离子液体[BMIM][DBP]+水+甲醇/乙醇三元工质溶液蒸汽压的测量和预测(英文)

The ionic liquid, 1-butyl-3-methylimidazolium dibutylphosphate ([BMIM][DBP]) was prepared and the vapor pressures of three set of binary solutions H2O(1)/CH3OH(1)/C2H5OH(1) + [BMIM][DBP](2) were measured at different temperature and in the ILs mole fraction range from 0.1 to 0.6 with a static equilibrium apparatus. The measured vapor pressures were correlated with Non-Random Two Liquid (NRTL) activity coefficient model and the average relative deviations (ARD) between experimental and correlated vapor pressures for these binary solutions were 3.19%, 2.42% and 2.95%, respectively. Then, the vapor pressures of two set of ternary solutions H2O(1) + CH3OH(2)/C2H5OH(2) + [BMIM][DBP](3) were measured with an inclined boiling apparatus and further predicted with NRTL activity coefficient model based on the binary interaction parameters coming from fitting the vapor pressures of the binary solutions. The results indicated that the ternary solutions containing [BMIM][DBP] were shown a strong negative deviation from Raoult’s Law when the mole fraction of [BMIM][DBP] was larger than 0.2, which meant that ternary solutions could absorb the refrigerant vapors at the same or below solution temperature. Meanwhile, the average relative deviations between experimental and predicted vapor pressures for ternary solutions were 2.92% and 3.06%, respectively. Consequently, the NRTL active coefficient model used for non-electrolyte solutions was still valid for predicting vapor-liquid equilibrium of binary or ternary solutions containing ILs.     

LiBr-[BMIM]Cl/H2O工质对的饱和蒸气压、结晶温度和腐蚀性

为了解决LiBr/H₂O工质对易结晶和腐蚀性强的问题,提出了LiBr-[BMIM]Cl/H₂O和LiBr-[BMIM]Br/H₂O新型工质对,研究了离子液体 [BMIM]Cl和[BMIM]Br对LiBr/H₂O结晶温度和饱和蒸气压的影响。对质量比为2.5的LiBr-IL(ionic liquids)/H₂O的饱和蒸气压、结晶温度和腐蚀性进行了测定并与LiBr/H₂O的进行了比较,结果表明[BMIM]Cl/H₂O和[BMIM]Br/H₂O的饱和蒸气压与质量分数低8%~9%的LiBr/H₂O的饱和蒸气压基本相同。在常用工作浓度范围内,LiBr-[BMIM]Cl/H₂O的结晶温度比相同吸收能力的LiBr/H₂O的低约30℃。在相同的腐蚀条件下,LiBr-[BMIM]Cl/H₂O对碳钢的腐蚀性明显小于LiBr/H₂O,对紫铜的腐蚀性与LiBr/H₂O的基本相同。因此,采用LiBr-[BMIM]Cl/H₂O作为替代工质对具有一定的应用潜力。     

Vapor pressure measurement and correlation of acetonitrile+1-butyl-3-methylimidazolium chloride,+1-butyl-3-methylimidazolium tetrafluoroborate,and+1-hexyl-3-methylimidazolium chloride

Vapor pressures were measured for acetonitrile+1-butyl-3-methylimidazolium chloride ([C4mim][Cl]),+1-butyl-3-methylimidazolium tetrafluoroborate ([C4mim][BF4]) and+1-hexyl-3-methylimidazolium chloride ...     

带共沸的乙醇/乙酸乙酯/2-丁酮三元物系变压精馏分离过程及其参数优化

提出了一种带两股循环的三塔变压精馏结构用于分离乙醇（C₂H₅OH）/乙酸乙酯（C₄H₈O₂-3）/2-丁酮（C₄H₈O-3）三元混合物。由该三元混合物的剩余曲线图（RCM）可知,在大气压下该混合物的每一对组元均形成二元最低共沸物,且乙醇/乙酸乙酯二元共沸物组成随压力变化敏感。三个最低共沸物的同时存在形成了精馏边界线夹紧点现象,而通常压力下的精馏塔无法跨越,以至于传统变压精馏无法应用。通过对精馏塔压力的最优化克服了这一困难,提出了新的分离流程,并对过程进行严格稳态模拟。针对初分塔（T1）塔压不同的6种流程,采用序贯迭代法对各塔的塔板数、进料板位置、回流比等参数进行了优化。通过对比6种流程的经济评价和比较,得到了T1塔的最优压力,并经过能量集成使得过程的年度总费用降低了14.88%。     

Preparation of multi-compositional gas sensing films by combinatorial solution deposition

Various compositions of gas sensing films were prepared by the combinatorial deposition of SnO₂, ZnO, and WO₃ sol solutions and their gas sensing behaviors were investigated. The film composition could be manipulated conveniently via the alternate dropping of different oxide sol solutions. From the correlation between film compositions and gas sensitivities, the selective detection of C₂H₅OH and CH₃COCH₃ in the presence of CO, C₃H₈, H₂, and NO₂ could be attained. In addition, the discrimination between C₂H₅OH and CH₃COCH₃, which is a challenging issue due to their similar chemical nature, becomes possible. This research demonstrates the precise design of the sensor-material composition for the selective gas detection via the combinatorial approach.     

醚基功能化离子液体催化合成乙酸正丁酯

合成了5种醚基功能化酸性离子液体[Me（OEt）₁-MOR-C₃SO₃H][MeSO₃]、[Me（OEt）₂-MOR-C₃SO₃H][MeSO₃]、[Me（OEt）₃-MOR-C₃SO₃H][MeSO₃]、[2（C₃SO₃H-MOR）-（OEt）₂₀₀][2MeSO₃]、[2（C₃SO₃H-MOR）-（OEt）₄₀₀][2MeSO₃],使用红外光谱和核磁共振氢谱对合成的离子液体结构进行表征,考察离子液体的黏度、溶解性和腐蚀性。以正丁醇和乙酸的酯化反应考察了离子液体的催化活性,并使用响应面分析法优化反应工艺。结果表明,当酸醇摩尔比为1.2：1、催化剂[2（C₃SO₃H-MOR）-（OEt）₄₀₀][2MeSO₃]用量为醇质量的5%、带水剂用量为醇质量的16%时,在90℃下反应5 h,酯收率可达97.8%,离子液体经回收干燥重复使用8次催化活性没有明显的降低。     

L-精氨酸衍生物的合成及其性质研究

以L-精氨酸(L-Arginine)和香兰素(Vanillin)为原料,首先合成新型的具有手性的希夫碱配体L(C_(14)H_(14)KN_3O_4),其次配体L分别与金属盐(CH_3COO)_2Ni·2H_2O、BaCl_2、(CH_3COO)_2Zn·2H_2O进行配位反应,得到3种新型的金属配合物(C_(16)H_(19)ZnKN_3O_7、C_(14)H_(14)BaClKN_3O_4和C_(18)H_(20)KN_3NiO_8),目标产物用IR、荧光分光光度计和元素分析仪等表征其结构,并用紫外漫反射光谱在可见光照射下,考察了配体L和3种新型的金属配位化合物的催化性能。实验结果推测配体L和L金属配合物均具有光催化性质,L金属配合物的催化性能更强。     

单乙醇胺和二乙醇胺甲酸盐离子液体对水、甲醇和乙醇挥发度的影响(英文)

Vapor pressures were measured for six binary systems containing water, ethanol, or methanol with one of the two ionic liquids （ILs） at different component concentrations and temperatures using a quasi-static ebulliometer, with the ILs mono-ethanolammonium formate （[HMEA][HCOO]） and di-ethanolammonium formate （[HDEA][HCOO]）. The vapor pressures of the IL-containing binary systems are well correlated using the NRTL model with an overall average absolute relative deviation （AARD） of 0.0062. The effect of ILs on the vapor pressure depression of sol-vents at 0.050 mole fraction of IL is that [HDEA][HCOO]〉[HMEA][HCOO], and the vapor pressure lowering de-gree follows the order of water〉methanol〉ethanol. Further, the activity coefficients of three solvents （viz. water, ethanol, and methanol） for the binary systems{solvent （1）＋IL （2）}predicted based on the fitted NRTL parameters at T=333.15 K indicate that the two ILs generate a negative deviation from Raoult’s law for water and methanol and a positive deviation for ethanol to a varying degree, change the relative volatility of a solvent. [HMEA][HCOO] may be a promising entrainer to efficiently separate ethanol aqueous solutions by special rectification.     

低黏二氰胺类离子液体乙烯汽液相平衡研究

从工业废气中回收分离乙烯（C₂H₄）具有重要意义,选用了三种低黏度二氰胺类离子液体,分别测定了293.15~333.15 K下其密度、黏度等物化性质,研究了其对乙烯（C₂H₄）吸收性能。采用非随机（局部）双液体模型（NRTL）关联了三种二元体系溶解度数据,实验值与计算值的平均相对偏差均小于3%。结果表明,低黏度二氰胺类离子液体对C₂H₄气体吸收性能良好,其中阳离子侧链长度增加和羟基功能团引入可增强对C₂H₄溶解度。同时,离子液体1-丁基-3-甲基咪唑二氰胺盐（[Bmim][DCN]）经过3次的吸收解吸循环,仍可以保持较好的C₂H₄吸收性能,表明该离子液体循环稳定性好,而1-丁基-3-甲基咪唑二氰胺盐（[Bmim][DCN]）对乙烯吸收量较高,具有作为C₂H₄吸收剂的潜力。     

Chemistry of surface oxygen formed from N2O on ZSM-5 at moderate temperatures

Conversion of CH₄, C₂H₆, C₃H₈, benzene and their binary mixtures over H-NaZSM-5 catalyst in the presence of N₂O was studied. It was found that under experimental conditions methane alkylates benzene to give toluene and xylenes. Acidity of the catalyst had no effect on the reactivity of active oxygen formed from N₂O towards methane and benzene, but affected their secondary transformation. Acidic samples favored the reaction of aromatic ring methylation with methane whereas deep oxidation of CH₄ prevailed on NaHZSM-5. Based on the relative reactivities and ¹³C label distribution in the products of ¹³CH₄+C₆H₆+N₂O feed conversion, the scheme of hydrocarbon transformation was proposed.     

溴肉桂醛衍生物的合成及其性质

以L-酪氨酸(L-Tyrosine)与溴肉桂醛为原料,首先合成了具有手性的新型席夫碱配体L、然后分别与乙酸铅和五水硫酸铜进行配位反应,生成了C₁₈H₁₅BrCuKNO₇S和C₂₂H₂₁BrKNO₇Pb两种新的氨基酸衍生物金属络合物。利用红外光谱、紫外光谱、质谱和荧光等进行表征和性质研究。结果表明,配体L在紫外区和可见区均可以作为光催化剂材料,配合物 C₂₂H₂₁BrKNO₇Pb只适合作为紫外光区的光催化剂材料。而C₁₈H₁₅BrCuKNO₇S络合产物不适合作为光催化剂材料。     

异丙醇钛控制水解的小角X射线散射研究

由金属醇盐水解制备溶胶的方法已广泛应用于溶胶-凝胶法制备纳米孔无机膜,但对金属醇盐水解机理的认识十分有限。通过控制异丙醇钛[Ti（i-OC₃H₇）₄]在异丙醇（i-C₃H₇OH）中水解制备TiO₂溶胶,利用小角X射线散射（SAXS）方法研究了由不同H₂O/Ti（i-OC₃H₇）₄的反应混合物[Ti（i-OC₃H₇）₄：H₂O：i-C₃H₇OH=1：m：30（摩尔比）]形成TiO₂溶胶的过程,探讨了控制Ti（i-OC₃H₇）₄水解的过程中胶粒形成与长大的规律。研究结果表明,所合成的TiO₂溶胶的胶粒粒径小于10 nm,胶粒的形成和长大与H₂O/Ti（i-OC₃H₇）₄摩尔比密切相关。H₂O/Ti（i-OC₃H₇）₄（摩尔比） ≥ 2.0时,随着H₂O/Ti（i-OC₃H₇）₄增加,溶胶的稳定性下降。     

含离子液体乙腈-正丙醇体系的等压汽液平衡

常压(101.3 kPa)下, 测定了如下体系的汽液平衡数据:乙腈-正丙醇-氯化1-苄基-3-甲基咪唑([BzMIM][Cl])、乙腈-正丙醇-溴化1-苄基-3-甲基咪唑([BzMIM][Br])、乙腈-正丙醇-溴化1-己基-3-甲基咪唑([HMIM][Br]), 考察了3种离子液体对乙腈-正丙醇体系相平衡行为的影响。实验结果表明, 3种离子液体都能够提高乙腈对正丙醇的相对挥发度, 3种离子液体提高相对挥发度的顺序为 [BzMIM][Cl] > [BzMIM][Br] > [HMIM][Br]。用NRTL模型对测得的汽液平衡数据进行了关联, 关联结果与实验结果具有良好的一致性。     

基于不同类型溶液蒸气压特性的太阳能界面蒸发实验研究

太阳能界面蒸发可实现高效太阳能海水淡化和蒸发式污水处理,但目前的研究大多局限于纯水或NaCl溶液。实际脱盐或废水处理中溶质会与此不同,导致溶液蒸气压变化并影响蒸发性能。本文首先分析了溶液表面蒸气压曲线类型,将其分为上凸型、下凹型和直线型。针对这几种蒸气压曲线进一步选取[EMIM][OTf]、[EMIM][Ac]和NaCl水溶液作为代表溶液,在不同辐照强度和浓度下进行了实验研究,并与纯水的蒸发作对比。实验结果表明：低浓度下[EMIM][OTf]水溶液展现出了良好的蒸发性能, 主要原因是由于其蒸气压处于上凸区间;当溶液浓度升高或辐照强度提升时,[EMIM][OTf]溶液的蒸发速率提升较NaCl水溶液小,主要原因在于蒸发过程的浓度极化导致气液界面处的[EMIM][OTf]浓度升高,蒸气压相差较小;不同工况下[EMIM][Ac]水溶液的蒸发速率均较慢,纯水的蒸发速率最快,体现了蒸气压对蒸发性能的关键影响,原因是低蒸气压导致高蒸发温度,并带来更多的能量损失。     

Water vapor sensitivity of nanosized La(Co, Mn, Fe)1−x(Cu, Pd)xO3 perovskites during NO reduction by C3H6 in the presence of oxygen

A series of La(Co, Mn, Fe)_1−x(Cu, Pd)_xO₃ perovskites having high specific surface areas and nanosized crystal domains was prepared by reactive grinding. The solids were characterized by N₂ adsorption, X-ray diffraction (XRD), scanning electron microscopy (SEM), temperature programmed desorption (TPD) of O₂, NO + O₂, C₃H₆, in the absence or presence of 5% H₂O, Fourier transform infrared (FTIR) spectroscopy, as well as activity tests towards NO reduction by propene under the conditions of 3000 ppm NO, 3000 ppm C₃H₆, 1% O₂, 0 or 10% H₂O, and 50,000 h⁻¹ space velocity. The objective was to investigate the influence of H₂O addition on catalytic behavior. A good performance (100% NO conversion, 77% N₂ yield, and 90% C₃H₆ conversion) was achieved at 600 °C over LaFe_0.8Cu_0.2O₃ under a dry feed stream. With the exposure of LaFe_0.8Cu_0.2O₃ to a humid atmosphere containing 10% water vapor, the catalytic activity was slightly decreased yielding 91% NO conversion, 51% N₂ yield, and 86% C₃H₆ conversion. A competitive adsorption between H₂O vapor with O₂ and NO molecules at anion vacancies over LaFe_0.8Cu_0.2O₃ was found by means of TPD studies here. A deactivation mechanism was therefore proposed involving the occupation of available active sites by water vapor, resulting in an inhibition of catalytic activity in C₃H₆ + NO + O₂ reaction. This H₂O deactivation was also verified to be strictly reversible by removing steam from the feed.     

Phase transitions in R2 SnCl6-type crystals (R = NH3 C2H3, NH3C2H5 and N(CH3)4)

The thermal dilatation in (NH₃ ·CH₃) SnCl₆, (NH₃ · C₂H₅) SnCl₆ and [N(CH₃)] SnCl₆ was measured, and as the results it has turned out that (NH₃ ⁶·C₂H₅) SnCl₆ and [N(CH₃)₄]₂ SnCl₆ undergo the first order transitions at 128 K and 158 K, respectively. The low temperature phases of (NH · C₂H₅) SnCl₆ and [N(CH₃)₄]₂ SnC1₆ are found to be monoclinic and tetragonal, respectively, No phase transition was observed in (NH₃ ·CH₃)₂ SnCl₆ down to 77 K.     

Boosting selective C2H2/CH4, C2H4/CH4 and CO2/CH4 adsorption performance via 1,2,3-triazole functionalized triazine-based porous organic polymers

Nitrogen-rich porous organic polymers have shown great potentials in gas adsorption/separation, photocatalysis, electrochemistry, sensing and so on. Herein, 1,2,3-triazole functionalized triazine-based porous organic polymers (TT-POPs) have been synthesized by the copper-catalyzed azide-alkyne cycloaddition (Cu-AAC) polymerization reactions of 1,3,5-tris(4-azidophenyl)-triazine with 1,4-diacetylene benzene and 1,3,5-triacetylenebenzene, respectively. The characterizations of N₂ adsorption at 77 K show TT-POPs possess permanent porosity with BET surface areas of 666 m²·g^-1 (TT-POP-1) and 406 m²·g^-1 (TT-POP-2). The adsorption capacities of TT-POPs for CO₂, CH₄, C₂H₂ and C₂H₄, as well as the selective separation abilities of CO₂/N₂, CO₂/CH₄, C₂H₂/CH₄ and C₂H₄/CH₄ were evaluated. The gas selective separation ratio of TT-POPs was calculated by the ideal adsorbed solution theory (IAST) method, wherein the selective separation ratios of C₂H₂/CH₄ and C₂H₄/CH₄ of TT-POP-2 was 48.4 and 13.6 (298 K, 0.1 MPa), which is comparable to other adsorbents (5.6-120.6 for C₂H₂/CH₄, 10-26 for C₂H₄/CH₄). This work shows that the 1,2,3-triazole functionalized triazine-based porous organic polymer has a good application prospect in natural gas purification.     

C2H6/C3H8影响CH4爆炸极限参数及动力学特性研究

为研究C₂H₆/C₃H₈对甲烷爆炸极限参数及动力学特性的影响,采用标准的可燃气体爆炸极限测定装置测定了不同配比的C₂H₆/C₃H₈混合气体对甲烷爆炸极限的影响规律,同时得出了氮气惰化条件下甲烷爆炸临界参数的变化规律。此外,利用Chemkin软件模拟了C₂H₆/C₃H₈混合气体对甲烷爆炸过程中中间产物浓度的影响情况,并进行了敏感性分析。结果表明,C₂H₆/C₃H₈的存在降低了甲烷的爆炸上下限,增大了甲烷的爆炸危险度;在氮气惰化过程中甲烷的爆炸上限下降,爆炸下限上升,最终爆炸上下限重合,重合点处甲烷浓度和氮气临界浓度均随C₂H₆/C₃H₈的添加而逐渐减小;此外,C₂H₆/C₃H₈混合气体使甲烷爆炸过程中CO和·H的生成量逐渐增大,而CO₂、·O和·OH的生成量则有下降趋势,通过对爆炸过程中甲烷体积的敏感性分析,发现C₂H₆/C₃H₈的存在在某种程度上促进了甲烷爆炸。对比不同配比的C₂H₆/C₃H₈混合气体,发现C₃H₈含量越高,其对甲烷爆炸过程中相关参数的影响越大,这可为工矿企业的安全生产提供一定的理论依据。     

CO, H2 or C3H8 assisted catalytic combustion of methane over supported LaMnO3 monoliths

The effect of the addition of a second fuel such as CO, C₃H₈ or H₂ on the catalytic combustion of methane was investigated over ceramic monoliths coated with LaMnO₃/La-γAl₂O₃ catalyst. Results of autothermal ignition of different binary fuel mixtures characterised by the same overall heating value show that the presence of a more reactive compound reduces the minimum pre-heating temperature necessary to burn methane. The effect is more pronounced for the addition of CO and very similar for C₃H₈ and H₂. Order of reactivity of the different fuels established in isothermal activity measurements was: CO>H₂≥C₃H₈>CH₄. Under autothermal conditions, nearly complete methane conversion is obtained with catalyst temperatures around 800 °C mainly through heterogeneous reactions, with about 60–70 ppm of unburned CH₄ when pure methane or CO/CH₄ mixtures are used. For H₂/CH₄ and C₃H₈/CH₄ mixtures, emissions of unburned methane are lower, probably due to the proceeding of CH₄ homogeneous oxidation promoted by H and OH radicals generated by propane and hydrogen pyrolysis at such relatively high temperatures.

Finally, a steady state multiplicity is found by decreasing the pre-heating temperature from the ignited state. This occurrence can be successfully employed to pilot the catalytic ignition of methane at temperatures close to compressor discharge or easily achieved in regenerative burners.     

Diamond and graphite crystallization from C–O–H fluids under high pressure and high temperature conditions

Crystallization of diamond was studied in the CO₂–C, CO₂–H₂O–C, H₂O–C, and CH₄–H₂–C systems at 5.7 GPa and 1200–1420°C. Thermodynamic calculations show generation of CO₂, CO₂–H₂O, H₂O and CH₄–H₂ fluids in experiments with graphite and silver oxalate (Ag₂C₂O₄), oxalic acid dihydrate (H₂C₂O₄·2H₂O), water (H₂O), and anthracene (C₁₄H₁₀), respectively. Diamond nucleation and growth has been found in the CO₂–C, CO₂–H₂O–C, and H₂O–C systems at 1300–1420°C. At a temperature as low as 1200°C for 136 h there was spontaneous crystallization of diamond in the CO₂–H₂O–C system. For the CH₄–H₂–C system, at 1300–1420°C no diamond synthesis has been established, only insignificant growth on seeds was observed. Diamond octahedra form from the C–O–H fluids at all temperature ranges under investigation. Diamond formation from the fluids at 5.7 GPa and 1200–1420°C was accompanied with the active recrystallization of metastable graphite.