Improvements in morphology,mechanical and thermal properties of films produced by reactive blending of poly(lactic acid)/natural rubber latex with dicumyl peroxide

The effect of dicumyl peroxide (DCP) as a free-radical cross-linking agent on the morphology, thermal and mechanical properties, and gas permeation of blown films prepared by reactive blending of poly(lactic acid) (PLA) and natural rubber latex was investigated. In comparison to the blown films without DCP, SEM micrographs revealed that the amount of debonded rubber domains from the cryofractured surface reduced considerably. This was when DCP at 0.003 phr was incorporated and the free radicals from thermally decomposed DCP reacted with PLA and NR chains, generating PLA–NR copolymers and cross-linked NR as confirmed by FTIR spectra. These PLA–NR copolymers acted as compatibilizers, which increased the strength at the PLA/NR interfaces, leading to the improvement in tensile strength, elongation at break, tensile toughness, impact strength, and tear strength. Although DCP did not influence the cold crystallization of PLA, TGA thermograms showed that thermal stability slightly increased owing to the enhanced interfacial adhesion. However, the addition of DCP at 0.005 and 0.010 phr resulted in a high content of cross-linked NR gel, by consuming the free radicals instead in copolymer formation. Therefore, the compatibilization efficiency was significantly reduced and the mechanical properties of reactive PLA/NR blown films finally dropped. Also, this poor interfacial adhesion facilitated the microvoid formation at the polymer–rubber interface as a result of mechanical stretching upon the film blowing process, increasing the permeation of water vapor and oxygen molecules. According to our study, it can be summarized that to optimize the morphology, mechanical properties, and gas permeation property of the free radical-assisted reactive blends, it is of great concern to carefully balance reactive compatibilizer formation and gel formation by adjusting the DCP content.     

Reactive modification and compatibilization of poly(lactide) and poly(butylene adipate‐co‐terephthalate) blends with epoxy functionalized‐poly(lactide) for blown film applications

Biodegradable blown films comprising of poly(lactide) (PLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) were produced using epoxy functionalized‐poly(lactide) (EF‐PLA) reactive modifiers for rheological enhancement and compatibilization. The epoxy groups on the EF‐PLA modifiers react with PBAT forming an in situ copolymer that localizes at the blend interphase resulting in compatibilization of the polymer blend components. The EF‐PLA modified polymer blends have improved melt strength and the resultant films showed better processability as seen by increased bubbled stability. This allowed for blown films with higher PLA content (70%) compared to the unmodified control films (40%). The static charge build‐up typically experienced with PLA film blowing was decreased with the inclusion of EF‐PLA yielding films with better slip and softness. The compatibilization effect of the EF‐PLA modifiers resulted in significant improvement in mechanical properties. For example, dart test performance was up to four times higher than the control, especially at higher PLA concentrations. Therefore, the rheological enhancement and compatibilization effects of the EF‐PLA reactive modifiers make them ideally suited to create high PLA content films. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43310.     

Improvement of microstructures and properties of poly(lactic acid)/poly(ε‐caprolactone) blends compatibilized with polyoxymethylene

Incompatibility of poly(lactic acid)/poly(?‐caprolactone) (PLA/PCL) (80:20) and (70:30) blends were modified by incorporation of a small amount of polyoxymethylene (POM) (≤3 phr). Impact of POM on microstructures and tensile property of the blends were investigated. It is found that the introduction of POM into the PLA/PCL blends significantly improves their tensile property. With increasing POM loading from zero to 3 phr, elongation at break increases from 93.2% for the PLA/PCL (70:30) sample to 334.8% for the PLA/PCL/POM (70:30:3) sample. A size reduction in PCL domains and reinforcement in interfacial adhesion with increasing POM loading are confirmed by SEM observations. The compatibilization effect of POM on PLA/PCL blends can be attributed to hydrogen bonding between methylene groups of POM and carbonyl groups of PLA and PCL. In addition, nonisothermal and isothermal crystallization behaviors of PLA/PCL/POM (70:30:x) samples were investigated by using differential scanning calorimetry and wide angle X‐ray diffraction measurements. The results indicate that the crystallization dynamic of PLA matrix increases with POM loadings. It can be attributed to the fact that POM crystals have a nucleating effect on PLA. While crystallization temperature is 100 °C, crystallization half‐time can reduce from 9.4 to 2.0 min with increasing POM loading from zero to 3 phr. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46536.     

膨胀阻燃三元乙丙橡胶/聚丙烯热塑性硫化胶的性能

分析了膨胀型阻燃剂聚磷酸铵(APP)、季戊四醇(PER)的加入方式对三元乙丙橡胶(EPDM)/聚丙烯(PP)体系硫化特性的影响,研究了加入不同膨胀型阻燃剂及协效剂硼酸锌(ZB)、有机蒙脱土(OMMT)对动态硫化EPDM/PP热塑性硫化胶(EPDM/PPTPV)性能的影响。结果表明,在动态硫化前加入APP或PER时,EPDM/PP体系不能进行硫化;当APP的加入量为30份时,EPDM/PPTPV的综合力学性能较佳;在EPDM/PPTPV中同时加入APP、PER、三聚氰胺(MEL)时,随着三者加入量的增加,体系的阻燃性能增强,但拉伸强度明显降低,三者的最佳用量为30份APP、10份PER、10份MEL,此时体系的黏度与纯EPDM/PPTPV相当;加入ZB或OMMT时,EPDM/PPTPV的拉伸强度降低,且加入OMMT体系的阻燃效果优于加入ZB体系;加入OMMT时,在低剪切速率下,体系的黏度减小;在高剪切速率下,体系的黏度增大;加入ZB时,在低剪切速率下,体系的黏度与未加ZB体系相当;在高剪切速率下,体系的黏度增大。     

In situ fibre‐reinforced composite films of poly(lactic acid)/low‐density polyethylene blends: effects of composition on morphology,transport and mechanical properties

This study aimed to investigate the effects of blend composition on packaging‐related properties of poly(lactic acid) (PLA) and low density polyethylene (LDPE) blown films. Blend films with PLA contents of 5–20 wt% were produced and compared. Scanning electron micrographs of cross‐sectional cryofractured surfaces of the blend films revealed that in situ fibre‐reinforced composites were obtained. Viscosity ratio of the polymer components of ca 1 confirmed that fibre formation was favourable for this blend system. PLA microdomains were dispersed throughout the film in forms of long fibres (length‐to‐diameter ratio > 100) and ribbons. The number of fibres and ribbons increased with an increase of PLA content. Critical content of PLA was found to be 20 wt% for effective improvement of both moduli and gas barrier properties. Incorporation of poly[ethylene‐co‐(methyl acrylate)] compatibilizer showed minimal effect on PLA structure. However, it did improve moduli and O₂ barrier properties when sufficient amount (1.5 pph) was used in 10 wt% PLA/LDPE. In short, flow behaviour, ratio of polymer components and degree of compatibility together played intricate roles in the morphology and hence mechanical and transport properties of PLA/LDPE immiscible blends. © 2017 Society of Chemical Industry     

Investigation on morphology and mechanical properties of polyamide 6/maleated ethylene‐propylene‐diene rubber/organoclay composites

Maleated ethylene‐propylene‐diene rubber (EPDM‐g‐MA) toughened polyamide 6 (PA6)/organoclay (OMMT) nanocomposites were prepared by melt blending. The role of OMMT in the morphology of the ternary composites and the relationship between the morphology and mechanical properties were investigated by varying the blending sequence. The PA6/EPDM‐g‐MA/OMMT (80/20/4) composites prepared by four different blending sequences presented distinct morphology and mechanical properties. The addition of OMMT could obviously decrease viscosity of the matrix and weaken the interfacial interactions between PA6 and EPDM‐g‐MA when blending EPDM‐g‐MA with a premixed PA6/OMMT nacocomposite, resulting in the increase of rubber particle size. The final mechanical properties are not only determined by the location of OMMT, but also by the interfacial adhesion between PA6 and EPDM‐g‐MA. Having maximum percentage of OMMT platelets in the PA6 matrix and keeping good interfacial adhesion between PA6 and EPDM‐g‐MA are beneficial to impact strength. POLYM. ENG. SCI., 2009. © 2008 Society of Plastics Engineers     

Rheological aspects and film processability of poly (lactic acid)/linear low-density polyethylene blends

Poly (lactic acid) (PLA) and Linear low-density polyethylene (LLDPE) were compounded in a corotating twin screw extruder. PE-g-glycidyl methacrylate was also added as a reactive compatibilizer in PLA/LLDPE blend system, which lowered interfacial tension between PLA and LLDPE. Blown films were prepared by using a single-screw extruder for all compounded blends. The investigation of the rheological properties of a polymeric system is very important to study the processability and understand structure-property relationship in blown films. In the present research work, the rheological properties have been investigated to assess the processability of blown films of PLA/LLDPE blends. Oscillatory shear rheology viscoelastic spectra showed an increase in the storage and loss moduli with the increase in LLDPE and compatibilizer content, which indicated pronounced viscoelastic behavior of PLA with the addition of LLDPE and compatibilizer. A steady increase in the value of extensional viscosity as a function of time was observed with the addition of LLDPE and compatibilizer in PLA. The blends with higher LLDPE content exhibited much more prominent strain hardening characteristics than those with lower LLDPE content.     

Structure and properties of poly(lactic acid)/poly(ε‐caprolactone) nanocomposites with kinetically induced nanoclay location

Poly(lactic acid)/poly(ε‐caprolactone)/organically modified montmorillonite (PLA/PCL/OMMT) nanocomposites were melt‐processed in a twin‐screw extruder under high shear conditions. As a result of the processing conditions employed, the OMMT layers located in the less compatible PCL phase in all the ternary nanocomposites. The morphology of the PLA/PCL blend evolved from “sea‐island” to co‐continuous upon the addition of OMMT. Both the X‐ray diffraction (XRD) and viscoelastic characterization suggested similar OMMT dispersion in the reference PLA binary and in the PLA/PCL ternary nanocomposites, regardless of its location in the PLA and PCL phase, respectively. The reinforcing effect of the organoclay was also similar. The addition of OMMT to the PLA/PCL blend fully compensated the loss in stiffness and oxygen barrier performance produced by PCL in PLA; the nanocomposite with 3% OMMT showed the same modulus and permeability values as those of pure PLA. Moreover, the ductile behavior (elongation at break > 80%) of the PLA/PCL blend remained constant even in the nanocomposite containing 5% OMMT. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43815.     

The Effect of Dynamic Vulcanization on the Mechanical Properties of EPDM/PP Thermoplastic Elastomers

ABSTRACT

EPDM/PP blends were prepared by melt mixing using Brabender Plasticorder at 200°C and 100 rpm. The curative concentration was progressively increased from 1 to 3.5 phr EPDM in order to study the influence of dynamic vulcanization on the mechanical properties of the blend. The effectiveness of dynamic vulcanization was ascertained by Brabender torque Rheometry, the increase in crosslink density, and the reduction in swelling index as well. The mechanical properties were found to increase with sulfur up to 1.4 phr after which reversion occurred. Scanning electron micrographs were inspected to differentiate between the cured EPDM/PP TPEs and the uncured counterpart. The micrographs showed that the blended system contains two incompatible phases. This is evident in both the case of the dynamically cured sample where the EPDM phase remains as dispersed particles in the PP matrix, and in the case of the uncured blend where the EPDM and PP formed two continuous phases.     

Design of highly tough poly(l‐lactide)‐based ternary blends for automotive applications

Technical renewable poly(l ‐lactide) (PLA)‐based blends represent an elegant way to achieve attractive properties for engineering applications. Recently, the miscibility between PLA and poly(methyl methacrylate) (PMMA) gave rise to new formulations with enhanced thermo‐mechanical properties but their high brittleness still remains a challenge to be overcome. This work here focuses on rubber‐toughened PLA/PMMA formulations for injection‐molding processes upon the addition of a commercially available ethylene‐acrylate impact modifier (BS). The miscibility between PLA and PMMA is not altered by the presence of BS but the incorporation of BS (17% by weight) into a PLA/PMMA matrix could enhance both ductility and toughness of PLA/PMMA blends for PMMA content up to 50 wt %. An optimum range of particle sizes (d_n ～0.5 µm) of the dispersed domains for high impact toughness is identified. These bio‐based ternary blends appear as promising alternatives to petro‐sourced blends such as ABS‐based blends in engineering injection‐molding parts. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43402.     

Miscibility of blends of ethylene‐propylene‐diene terpolymer and polypropylene

The miscibility of polymers is not only an important basis for selecting a proper blending method, but it is also one of the key factors in determining the morphology and properties of the blends. The miscibility between ethylene‐propylene‐diene terpolymer (EPDM) and polypropylene (PP) was explored by means of dynamic mechanical thermal analysis, transmission electron microscopy (TEM), and differential scanning calorimetry (DSC). The results showed that a decrease in the PP content and an increase of the crosslinking density of EPDM in the EPDM/PP blends caused the glass‐transition temperature peaks of EPDM to shift from a lower temperature to higher one, yet there was almost no variance in the glass‐transition temperature peaks of PP and the degree of crystallinity of PP decreased. It was observed that the blends prepared with different mixing equipment, such as a single‐screw extruder and an open mill, had different mechanical properties and blends prepared with the former had better mechanical properties than those prepared with the latter. The TEM micrographs revealed that the blends were composed of two phases: a bright, light PP phase and a dark EPDM phase. As the crosslinking degree of EPDM increased, the interface between the phases of EPDM and PP was less defined and the EPDM gradually dispersed in the PP phase became a continuous phase. The results indicated that EPDM and PP were both partially miscible. The mechanical properties of the blends had a lot to do with the blend morphology and the miscibility between the blend components. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 315–322, 2002     

Effect of dynamic crosslinking on impact strength and other mechanical properties of polypropylene/ethylene‐propylene‐diene rubber blends

The deformation and fracture behavior of several dynamic vulcanizate blends of isotactic polypropylene with ethylene‐propylene‐diene rubber (EPDM) was examined and compared with those of uncrosslinked blends of PP/EPDM. These blends were prepared by melt mixing in an internal mixer at 190°C in a composition range of 10–40 wt % EPDM rubber. The variation in yield stress, the strength of fibrils of the craze, and the number density of the EPDM rubber domains (morphology fixation) that are dominant factors for enhancing interfacial adhesion and toughness in dynamic vulcanizate blends were evaluated. The ductility and toughness of these materials were explained in light of the composition between crack formation and the degree of plastic deformation through crazing and shear yielding. The physicomechanical properties including the hardness, yield stress, Young's modulus, percentage elongation, impact strength, flexural strength, and flexural modulus of dynamic vulcanized blends were found to be consistent and displayed higher values compared with uncrosslinked blends. The nucleation effect of the crosslinked particles and the decrease of crystallinity of the EPDM rubber were also considered to contribute to the improvement in the impact strength. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2089–2103, 2000     

Structure and mechanical properties of nanodispersed fibrous silicate‐reinforced ethylene–propylene–diene monomer nanocomposites

In this study, ethylene–propylene–diene monomer (EPDM)/fibrillar silicate (FS) nanocomposites were successfully prepared by mechanically blending EPDM with FS, which was modified by silane coupling agent KH570 containing methacryloxy group. The effects of silane content and modified FS on the dispersion of FS and mechanical properties of the composites were investigated. The impact of water in FS on mechanical properties of the composites was also evaluated. The results showed that modified FS could be dissociated into nanofibers dispersing evenly in the EPDM matrix by increasing substantially the loading of silane through the mechanical blending. The optimum loading level of silane coupling agent was up to 24 phr/100 phr FS. Silane KH570 could improve the dispersion of FS and strengthen nanofibers–rubber interfacial adhesion even at the loading of as high as 50 phr FS, making FS to exhibit excellent reinforcement to EPDM. Too much FS could not be completely dissociated into nanofibers, slowing down further improvement. The EPDM/FS composites exhibited the similar stress–strain behavior and obvious mechanical anisotropy with short microfiber‐reinforced rubber composites. With the increase in silane coupling agent and modified FS, the number of nanofibers increased because of the exfoliation of FS microparticles; thus, the mechanical behaviors would become more obvious. It was suggested that the free water in FS should be removed before mechanically blending EPDM with FS because it obviously affected the tensile properties of the composites. Regardless of whether FS was dried or modified, the EPDM/FS composites changed little in tensile strength after soaked in hot water. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synergetic toughness and morphology of poly(propylene)/nylon 11/maleated ethylene‐propylene diene copolymer blends

Polypropylene (PP)/nylon 11/maleated ethylene‐propylene‐diene rubber (EPDM‐g‐MAH) ternary polymer blends were prepared via melt blending in a corotating twin‐screw extruder. The effect of nylon 11 and EPDM‐g‐MAH on the phase morphology and mechanical properties was investigated. Scanning electron microscopy observation revealed that there was apparent phase separation for PP/EPDM‐g‐MAH binary blends at the level of 10 wt % maleated elastomer. For the PP/nylon 11/EPDM‐g‐MAH ternary blends, the dispersed phase morphology of the maleated elastomer was hardly affected by the addition of nylon 11, whereas the reduced dispersed phase domains of nylon 11 were observed with the increasing maleated elastomer loading. Furthermore, a core‐shell structure, in which nylon 11 as a rigid core was surrounded by a soft EPDM‐g‐MAH shell, was formed in the case of 10 wt % nylon 11 and higher EPDM‐g‐MAH concentration. In general, the results of mechanical property measurement showed that the ternary blends exhibited inferior tensile strength in comparison with the PP matrix, but superior toughness. Especially low‐temperature impact strength was obtained. The toughening mechanism was discussed with reference to the phase morphology. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Solid‐state mechanical properties of polypropylene/nylon 6/clay nanocomposites

The mechanical and thermomechanical properties as well as microstructures of polypropylene/nylon 6/clay nanocomposites prepared by varying the loading of PP‐MA compatibilizer and organoclay (OMMT) were investigated. The compatibilizer PP‐MA was used to improve the adhesion between the phases of polymers and the dispersion of OMMT in polymer matrix. Improvement of interfacial adhesion between the PP and PA6 phases occurred after the addition of PP‐MA as confirmed by SEM micrographs. Moreover, as shown by the DSC thermograms and XRD results, the degree of crystallinity of PA6 decreased in the presence of PP‐MA. The presence of OMMT increased the tensile modulus as a function of OMMT loading due to the good dispersion of OMMT in the matrix. The insertion of polymer chains between clay platelets was verified by both XRD and TEM techniques. The viscosity of the nanocomposites decreased as PP‐MA loading increased due to the change in sizes of PA6 dispersed phase, and the viscosity increased as OMMT loading increased due to the interaction between the clay platelets and polymer chains. The clay platelets were located at the interface between PP and PA6 as confirmed by both SEM and TEM. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

A Facile Strategy for Compatibilization of PLA/PBS Blends by Incorporating Camellia Seed Powder

Using biodegradable blending materials is one of the most effective ways to address plastic pollution but it is hindered by its poor interfacial interaction along with high costs. Herein, an envirionmentally friendly filler, camellia seed powder (CSP)−a byproduct of camellia seed after defatting, is reported, which is first served as a compatibilizer in polylactic acid (PLA)/polybutylene succinate (PBS) blends without any other aids or complicated pretreatment, effectively toughening the PLA/PBS blends due to a better interfacial interaction. The results show that the toughness of composites increases with CSP content. With the addition of 30 phr CSP, its impact strength and elongation at break increase by 44.31% and 148.42%, respectively, as compared with the blend without CSP. The combined effects of improved interfacial bonding, reduced particle size of PBS and efficient stress transfer are responsible for the toughness enhancement. The compatibilization mechanism is proposed that ─COOH groups in PLA and PBS react with ─NH₂ in CSP. The above finding of CSP as a compatibilizer provides a facile and inexpensive strategy in the fabrication of high-performance biodegradable materials.     

Silica‐reinforced dynamically vulcanized ethylene–propylene–diene monomer/polypropylene thermoplastic elastomers: Morphology,rheology, and dynamic mechanical properties

Attempts were made to prepare dynamically crosslinked ethylene–propylene–diene monomer/polypropylene (EPDM/PP, 60/40 w/w) blends loaded with various amounts of silica as a particulate reinforcing agent. The dispersion of silica between the two phases under mixing conditions, and also extent of interaction, as the two main factors that influence the blend morphology were studied by scanning electron microscopy. Increasing the silica concentration led to the formation of large‐size EPDM aggregates shelled by a layer of PP. Dynamic mechanical thermal analysis performed on the dynamically cured silica‐loaded blend samples showed reduction in damping behavior with increasing silica content. Higher rubbery‐like characteristics under tensile load were exhibited by the silica‐filled EPDM/PP‐cured blends. However, increasing the silica level to 50 phr led to the enhancement of interface, evidenced by increases in the tensile modulus and extensibility of the blend compared with those of the unloaded sample. Addition of a silane coupling agent (Si69) into the mix improved the mechanical properties of the blend, attributed to the strengthening of interfacial adhesion between the PP matrix and silica‐filled EPDM phase. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2000–2007, 2004     

Enhancing gas barrier performance of polylactic acid/lignin composite films through cooperative effect of compatibilization and nucleation

In this work, lignin was used as a heterogeneous nucleating agent to increase polylactic acid (PLA) crystallinity. To enhance the gas barrier performance of PLA/LG composite films, two graft copolymers, polylactide-graft-glycidyl methacrylate (PLA-g-GMA) and polylactide-graft-poly (ethylene glycol) methyl ether methacrylate (PLA-g-PEGMA) were successfully synthesized and separately used as compatibilizers to modify PLA/LG composite properties such as interfacial adhesion, crystallinity, and mechanical properties. Since crystallites can act as obstacles to gas diffusion, the higher the crystallinity of the polymer matrix, the better gas barrier performance of the composite film will be. The crystallinity and crystalline structure of the PLA matrix was demonstrated by wide-angle X-ray diffraction and differential scanning calorimetry results. Since LG particles can act as efficient heterogeneous crystal nucleating agents, a roughly 50% reduction in oxygen permeability (P_O2) was obtained by adding 1 phr LG to the PLA matrix (PLA/1LG). Following addition of 10 phr PLA-g-GMA to the PLA/LG composite, PLA/PLA-g-GMA/LG composite films showed lower gas barrier properties than PLA/LG composites without added compatibilizer. Moreover, the interfacial adhesion of PLA/LG composites was significantly improved after addition of PLA-g-GMA. Therefore, PLA/PLA-g-GMA/3LG showed the highest tensile strength, 33% higher than that of neat PLA. Following addition of 10 phr PLA-g-PEGMA to the PLA/LG composite, the long liner side chains of PLA-g-PEGMA were able to act as nucleating agents for PLA to promote the crystallization of PLA. Accordingly, PLA/PLA-g-PEGMA/3LG with 3 phr LG showed a roughly 86% reduction in P_O2 when compared with neat PLA film.     

Toughening and compatibilization of polypropylene/polyamide‐6 blends with a maleated–grafted ethylene‐co‐vinyl acetate

In this article, maleated–grafted ethylene‐co‐vinyl acetate (EVA‐g‐MA) was used as the interfacial modifier for polypropylene/polyamide‐6 (PP/PA6) blends, and effects of its concentration on the mechanical properties and the morphology of blends were investigated. It was found that the addition of EVA‐g‐MA improved the compatibility between PP and PA6 and resulted in a finer dispersion of dispersed PA6 phase. In comparison with uncompatibilized PP/PA6 blend, a significant reduction in the size of dispersed PA6 domain was observed. Toluene‐etched micrographs confirmed the formation of interfacial copolymers. Mechanical measurement revealed that the addition of EVA‐g‐MA markedly improved the impact toughness of PP/PA6 blend. Fractograph micrographs revealed that matrix shear yielding began to occur when EVA‐g‐MA concentration was increased upto 18 wt %. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99:3300–3307, 2006     

PLA/PPC/OMMT纳米复合材料的结构与性能研究

采用双螺杆挤出机制备了聚乳酸（PLA）/聚碳酸亚丙酯（PPC）共混物和PLA/PPC/有机改性蒙脱土（OMMT）纳米复合材料,采用偏光显微镜、差示扫描量热仪和力学性能试验机等对共混物和纳米复合材料的相态结构、熔融与结晶行为和力学性能等进行了研究。结果表明,在PPC含量低于30 %时,随着PPC含量的增加,PLA/PPC和PLA/PPC/OMMT体系中PLA的玻璃化转变温度（Tg）均降低,在PPC含量为50 %时出现了明显的相分离;随着PPC含量的增加,PLA/PPC的冲击强度增大;OMMT的含量小于1.5 %时,PLA/PPC/OMMT体系的结晶度、拉伸强度、断裂伸长率和冲击强度均随OMMT含量的增加而增大。