阴离子表面活性剂辅助模板途径合成介孔结构氧化锆纳米晶

利用阴离子表面活性剂十二烷基磺酸钠(SDS)为辅助模板剂, 成功地合成了高稳定性的介孔氧化锆纳米晶, 采用DSC-TG, FT-IR, XRD, TEM, UV-Vis以及N₂吸附-脱附等方法对样品进行了表征. 研究表明, 以阴离子型十二烷基磺酸钠合成的氧化锆经600 ℃煅烧后仍为纯四方相, 氧化锆晶粒平均尺寸约为6.5 nm. 阴离子型表面活性剂与有机锆源形成自组装协同作用, 合成的氧化锆具有蠕虫状介孔结构, 经过500 ℃煅烧后介孔结构仍然保持, 且由于表面活性剂的去除, 比表面积显著提高, 显示了良好的热稳定性. 本实验制备的氧化锆纳米晶较一般方法制备的市售纳米氧化锆有明显紫外吸收边蓝移现象.     

超低硅铝比多级孔ZSM-5分子筛的无模板剂合成

以水玻璃为硅源、Al₂(SO₄)₃·18H₂O为铝源,投料硅铝比SAR=n(SiO₂)/n(Al₂O₃)=40,前躯体凝胶pH=11.2、Na₂O/SiO₂=0.18、 H₂O/SiO₂=43、m(晶种)/m(SiO₂)=0.16,不添加任何模板剂条件下合成了具有多级孔结构的超低硅铝比ZSM 5分子筛,其结构经²⁷Al NMR, SEM-EDS, Py-IR, NH₃-TPD, XRD和N₂-吸脱附表征。SEM结果表明ZSM-5分子筛晶体为侧面呈“维管束”状的长方体;EDS分析表明其表面硅铝分布具有显著不均一性：顶底表面SAR=20,侧面SAR=13。NH₃-TPD分析表明：该ZSM-5分子筛整体具备可观的弱酸总酸量(1.9 mmol·g^-1),且以Lewis酸为主。N₂吸脱附实验表明：ZSM-5分子筛存在明显的介孔结构,属同时含有微孔-介孔结构的多级孔、超低硅铝比ZSM-5分子筛。     

ZSM-5、ZSM-57分子筛和丝光沸石间的转晶规律

考察了硅铝比、碱度、有机胺模板剂、晶化时间及温度等合成条件对ZSM-5、ZSM-57 分子筛和丝光沸石之间相互转晶的影响. 发现较高的碱度、较长的晶化时间有利于合成丝光沸石；较低的碱度、较高的诱导晶化温度、较长的晶化时间有利于合成低硅铝比的ZSM-57 分子筛；合成低硅铝比的ZSM-5分子筛则需要在能合成丝光沸石和ZSM-57 分子筛的碱度区间内精确调节碱度, 缩短晶化时间、降低诱导晶化温度、加入适当晶种, 有利于合成低硅铝比的ZSM-5 分子筛. 合成条件稍微改变, 会导致各种沸石之间发生转晶, 晶化产物出现两种或两种以上的晶型.     

一步法合成多级孔结构ZSM-5分子筛

多级孔结构ZSM-5分子筛的合成过程复杂。利用双模板剂,通过优化晶化条件(如晶化时间与晶化温度)和Si/Al物质的量比等一步水热晶化合成了具有多级孔结构的ZSM-5分子筛,并采用XRD、N₂吸附-脱附、吡啶红外吸脱附、SEM和TEM等方法对样品的晶体结构、孔道结构、表面酸性和形貌等进行了表征。结果表明,一步法合成多级孔结构ZSM-5分子筛的适宜条件是:晶化温度160-180℃,晶化时间24-96 h,反应物组成为SiO₂/Al₂O₃/Na₂O/CTAB/TPABr/H₂O=1/x/0.4/0.05/0.12/280,(x:50-240)。其中,晶化温度160℃、晶化时间48 h和以Si/Al物质的量比50的凝胶合成的样品具有有序的介孔(平均尺寸3.60 nm)结构、较高的结晶度和较强的酸性。     

混合阳离子-非离子表面活性剂为模板剂合成含沸石次级结构单元的介孔分子筛

利用混合阳离子-非离子表面活性剂为模板剂采用两步晶化法合成了孔壁具有沸石次级结构单元的介孔分子筛，通过XRD、N2吸附-脱附、FT-IR以及异丙苯裂解探针反应等手段对样品进行了表征。结果表明，合成的介孔材料在结构上与相应的M41S材料类似，无微孔沸石相的存在。立方介孔材料具有较高的热稳定性和水热稳定性，在催化异丙苯裂解反应中，六方介孔材料的催化活性明显高于相似条件下用单一表面活性剂为模板剂合成的含沸石次级结构单元的六方介孔材料。     

Ti-Si介孔分子筛的转晶与控制

以季铵盐型阳离子Gemini表面活性剂[C16H33(CH3)2N+(CH2)6N+(CH3)2C16H33]•2Br−(GEM16-6-16)为模板剂, 改变n(Ti)/n(Si)比值, 合成了系列Ti-Si介孔分子筛. X射线衍射(XRD)和透射电子显微镜(TEM)等表征结果表明, 在n(Ti)/n(Si)≤0.20时, 分子筛为高度有序六方介孔; 当 n(Ti)/n(Si)为 0.30时, 介孔转晶为立方相; 当n(Ti)/n(Si)为0.50时, 介孔转晶为层状相; n(Ti)/n(Si)为1.0时, 材料失去有序孔道结构. FT-IR分析表明, 在分子筛骨架间形成了Ti—O—Si键, 而且Ti—O—Si键的数目随n(Ti)/n(Si)的增加而增加, 达到一定饱和值后基本保持不变. 乙醇和丁醇对纯硅基介孔分子筛孔结构转晶控制作用呈现六方相→立方相→层状相递变规律, 因而钛酸正丁酯水解生成的丁醇对Ti-Si介孔分子筛转晶具有一定的控制作用.     

不同模板剂合成具有介微结构的ZSM-5分子筛及其甲醇制丙烯性能

分别采用四丙基氢氧化铵(TPAOH),十六烷基三甲基溴化铵(CTAB)和N-十八烷基-N'-己基-四甲基-1, 6-己二铵(C_18-6-6Br₂)作为模板剂,合成了具有不同介微结构的纳米ZSM-5分子筛(NZ),介孔ZSM-5分子筛(MZ)和纳米薄层ZSM-5分子筛(NSZ).对合成的样品进行X射线衍射(XRD),扫描电子显微镜(SEM), N₂吸附-脱附和氨程序升温脱附(NH₃-TPD)表征,并与传统微孔ZSM-5分子筛(CZ)对比.结果表明,样品的介孔孔容和外表面积大小的顺序为NSZ > MZ > NZ > CZ,强/弱酸之比的顺序为CZ > MZ > NZ > NSZ.在甲醇制丙烯(MTP)反应中,催化剂的介微结构特征影响MTP反应的产物选择性及稳定性,丙烯和总低碳烯烃选择性随着介孔孔容的增加而增加, NSZ样品具有最高的丙烯选择性(47.5%)及总低碳烯烃选择性(78.4%).此外,介孔的引入能适当延长催化剂的寿命,具有适宜酸性质的NZ样品的催化寿命最长(200 h).     

晶种导向下干胶法合成ZSM-5分子筛

以廉价水玻璃为硅源,在晶种替代有机模板剂的条件下采用干胶法合成了ZSM-5分子筛。利用XRD、SEM、TEM、FTIR、N₂吸附-脱附和NH₃-TPD等分析方法对合成样品进行了表征和测试,考察了合成条件对ZSM-5分子筛晶化过程的影响。结果表明,在硅铝比（n/n）为30~70,钠硅比（n/n）为0.12~0.20时都可以得到结晶度良好的ZSM-5分子筛。研究发现,干胶法合成ZSM-5,在不引入外加水的情况下也可以得到ZSM-5样品,外加水的引入能够有效地提高晶化速率;与水热法合成ZSM-5分子筛相比,干胶法可以显著地缩短晶化时间,同时,合成样品的晶体尺寸也有所减小。     

晶种导向下干胶法合成ZSM-5分子筛

以廉价水玻璃为硅源,在晶种替代有机模板剂的条件下采用干胶法合成了ZSM-5分子筛。利用XRD、SEM、TEM、FTIR、N_2吸附-脱附和NH_3-TPD等分析方法对合成样品进行了表征和测试,考察了合成条件对ZSM-5分子筛晶化过程的影响。结果表明,在硅铝比(n/n)为30~70,钠硅比(n/n)为0.12~0.20时都可以得到结晶度良好的ZSM-5分子筛。研究发现,干胶法合成ZSM-5,在不引入外加水的情况下也可以得到ZSM-5样品,外加水的引入能够有效地提高晶化速率;与水热法合成ZSM-5分子筛相比,干胶法可以显著地缩短晶化时间,同时,合成样品的晶体尺寸也有所减小。     

无模板剂条件下ZSM-5与丝光沸石之间的可控转晶

采用预晶化液添加法,即将高温(190oC)预晶化液添加到低温(150oC)晶化母液中合成沸石分子筛,考察了高温预晶化液的Na2O:SiO2比、预晶化时间以及低温晶化母液的Na2O:SiO2比对ZSM-5与丝光沸石之间转晶的影响,并采用X射线衍射和扫描电子显微镜对合成的产物进行了表征.研究发现,通过调节整体合成液的Na2O:SiO2比可有效控制ZSM-5沸石与丝光沸石之间的转晶.当整体合成液的组成为xNa2O:100SiO2:2.5Al2O3:12SO42?:4000H2O时,Na2O:SiO2=0.18是ZSM-5沸石和丝光沸石的一个分界线.通过调节母液的Na含量,使Na2O:SiO2>0.18时,高温预晶化过程中产生MFI结构的晶体在低温晶化时可向丝光沸石发生转晶;当Na2O:SiO2≤0.18时,具有MFI和丝光沸石结构共生的晶体在低温晶化时向MFI结构的ZSM-5沸石发生转晶.ZSM-5与丝光沸石之间转晶的前提条件是高温预晶化所形成晶体的结晶度不能太高(≤30%).另外,整体合成液中Na2O含量对生成晶体的形貌也有影响.     

分步晶化法合成ZSM-5/SAPO-5复合材料

通过分步晶化水热处理的方式合成了ZSM-5/SAPO-5复合材料。研究了两种分子筛凝胶的混合方式、调节ZSM-5母液的酸类型、SAPO-5凝胶组成以及晶化时间对复合材料形成的影响。实验结果表明,简单将两种分子筛的合成凝胶混合不能得到复合材料。采用H₂SO₄调节ZSM-5合成母液的pH值,在ZSM-5与SAPO-5理论质量比为3.5、SAPO-5凝胶中P₂O₅与Al₂O₃摩尔比为1.2的条件下可以得到ZSM-5/SAPO-5复合材料。但样品中含有少量无定形物质,这些无定形通过延长晶化时间并不能完全消除。     

新型腰果酚双子表面活性剂的合成及表面活性

以天然生物质腰果酚、1,3-二溴丙烷及氯磺酸为原料,通过醚化、磺化及中和三步反应合成了一类新型的腰果酚基磺酸盐双子(Gemini)表面活性剂.采用傅立叶转换红外光谱仪和核磁共振谱仪表征了产物的结构;采用滴体积法测定了腰果酚Gemini表面活性剂的表面张力,研究了水溶液的表面性质,并与相应的单基腰果酚基磺酸盐表面活性剂进行了对比.结果表明:腰果酚Gemini表面活性剂水溶液的临界胶束浓度(cmc)为6.20×10-2 mmol.L-1,远小于相应的单基腰果酚表面活性剂水溶液的cmc(8.40mmol.L-1);其临界表面张力γcmc为36.92mN.m-1,与单基腰果酚表面活性剂水溶液的相近(γcmc为38.41mN.m-1).与此同时,腰果酚Gemini表面活性剂水溶液的最小分子截面积Amin为0.27nm2,比相应的单基表面活性剂水溶液的小得多.     

Rapid crystallization and morphological adjustment of zeolite ZSM-5 in nonionic emulsions

Zeolite ZSM-5 was synthesized for the first time in a nonionic emulsion composed of polyoxyethylated alkylphenol, butanol, cyclohexane and tetraethylammonium hydroxide (TEAOH)-containing zeolite synthesis mixture. The crystallization kinetics in the emulsion was investigated and the ZSM-5 product was characterized in detail by XRD, SEM, FT-IR, TG, N₂ adsorption and CHN analysis techniques. Compared with the conventionally hydrothermal synthesis with the same structure directing agent TEAOH, the emulsion system allows rapid crystallization of ZSM-5. The ZSM-5 product exhibits unusual agglomerated structure and possesses larger specific surface area. The FT-IR, TG results plus CHN analysis show the encapsulation of a trace of emulsion components in the emulsion ZSM-5. Control experiments show the emulsion system exerts the crystallization induction and morphological adjustment effects mainly during the aging period. The effects are tentatively attributed to the confined space domains, surfactant-water interaction as well as surfactant-growing crystals interaction existing in the emulsion.     

Synthesis and surface properties of PDMS–acrylate emulsion with gemini surfactant as co-emulsifier

Composite latex particles of acrylate and polydimethylsiloxane (PDMS) with high PDMS content was prepared by emulsion copolymerization and characterized by particle size analyzer, X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR). With gemini surfactant as the co-emulsifier in the system, the PDMS content in the system reached 50%, which was far higher than the other reported values. Through the characterization of the particle size analyzer, the particle size augmented with the increase of the amount of PDMS, which could be said that the polysiloxane had participated into the reaction and had been introduced into the colloid particle. The results of FTIR indicated that almost all the monomer had been exhausted in the reaction because there was no C=C and D₄ characteristic peaks in the spectrum. Besides the surface properties also were measured by surface tension analysis, water absorption, and the static contact angle, it could be found that with the increase of polysiloxane content, the excellent properties acquired by PDMS were clearly revealed by the findings, such as the decrease of surface tension and water absorption, and the increase of static contact angle. All the measurements were consistent with the conclusion that the composite latex particles of polysiloxane and acrylate with high siloxane content had been prepared successfully.     

Phase-transfer catalysis of a new cationic gemini surfactant with ester groups for nucleophilic substitution reaction

A highly effective phase transfer of a quaternary ammonium gemini surfactant with ester groups（（diethylhexanedioate） diyl-a,v-bis（dimethyl dodecyl ammonium bromide） referred to as 12-10-12）was synthesized with high yield and characterized by infrared spectroscopy, elemental analysis and1 HNMR. Then, 12-10-12 was used as a phase transfer catalyst to study the catalytic effect on the reaction of anhydrous sodium acetate and 4-methylbenzyl chloride. The possible catalytic mechanism and the influence of surfactant concentration, temperature and type are also discussed. The experimental results showed that the catalysis efficiency was more active than the traditional, single-chained surfactant,tetrabutyl ammonium bromide. It also revealed that the reaction was first-order with respect to the concentration of 4-methylbenzyl chloride. The concentration of 4-methylbenzyl chloride grew linearly with the concentration of 12-10-12 and as the reaction temperature increased. The optimum reaction time was 7 h.     

Synthesis of conducting polyaniline using novel anionic Gemini surfactant as micellar stabilizer

The Gemini surfactant 9B-4-9B containing sodium sulfonate as hydrophilic head group was synthesized based on nonylphenol and characterized by FTIR, ¹H NMR spectroscopy and the surface tension measurement. The CMC and C₂₀ of the 9B-4-9B were smaller than that of sodium dodecylbenzene sulfonate and sodium dodecylsulfate, respectively, indicating excellent efficiency of micelle formation and reduced surface tension. Conducting polyaniline salts were synthesized by chemical oxidative micellar polymerization of aniline in water firstly using Gemini surfactant 9B-4-9B as the micelle stabilizer and ammonium peroxydisulfate as the oxidant at 0 °C. The stable polyaniline dispersions have been obtained when the molar ratio of the 9B-4-9B to aniline was equal to or above 0.5 used in the polymerization system. The obtained granular polyaniline particles with the size of 1-2 μm were characterized by FTIR, UV-Vis, SEM, WAXD and conductivity measurement.     

Synthesis and characterization of a microcystalline ZSM-5 molecular sieve

Microcrystalline ZSM-5 zeolite has been prepared and characterized by using XRD, SEM, FT-IR, nitrogen adsorption, MASNMR techniques and the methanol to olefin (MTO) reaction. The selectivity of the MTO reaction is comparatively high.     

介孔ZSM-5沸石微球催化剂上萘的苄基化反应

以有机硅烷化的二氧化硅为硅源,制备了由纳米粒子聚集而成的、具有晶间和晶内介孔的微球状ZSM-5（MMZ-5）沸石. 通过吡啶（Py）和2,6-二叔丁基吡啶（DTBPy）在介孔沸石表面吸附的原位红外测试,对其酸性进行了表征. 与微孔ZSM-5 沸石相比,MMZ-5 沸石上的Lewis 酸位和总酸位增加,特别是探针大分子DTBPy（动力学直径约为1.05 nm）可及的Brönsted 酸位显著提高. 萘在MMZ-5沸石上的苄基化催化结果表明,反应发生在拥有大量活性位的沸石外表面,大的沸石外表面为该催化反应提供了作用空间,从而提高了沸石活性位的有效利用率,使MMZ-5 沸石上萘的苄基化反应活性显著提高,能够生成大分子产物一苄基萘和二苄基萘;其中,一苄基萘的选择性约为79%,且随着反应时间的延长,MMZ-5 沸石大的晶内介孔（3-5 nm）为反应提供了有效反应空间,促进一苄基萘向二苄基萘转化. 异构体α-一苄基萘和β-一苄基萘的摩尔比值约为83：17,该值不随着温度和转化率的变化而改变.     

介孔ZSM-5沸石微球催化剂上萘的苄基化反应

以有机硅烷化的二氧化硅为硅源,制备了由纳米粒子聚集而成的、具有晶间和晶内介孔的微球状ZSM-5(MMZ-5)沸石.通过吡啶(Py)和2,6-二叔丁基吡啶(DTBPy)在介孔沸石表面吸附的原位红外测试,对其酸性进行了表征.与微孔ZSM-5沸石相比,MMZ-5沸石上的Lewis酸位和总酸位增加,特别是探针大分子DTBPy(动力学直径约为1.05 nm)可及的Br?nsted酸位显著提高.萘在MMZ-5沸石上的苄基化催化结果表明,反应发生在拥有大量活性位的沸石外表面,大的沸石外表面为该催化反应提供了作用空间,从而提高了沸石活性位的有效利用率,使MMZ-5沸石上萘的苄基化反应活性显著提高,能够生成大分子产物一苄基萘和二苄基萘;其中,一苄基萘的选择性约为79%,且随着反应时间的延长,MMZ-5沸石大的晶内介孔(3-5 nm)为反应提供了有效反应空间,促进一苄基萘向二苄基萘转化.异构体α-一苄基萘和β-一苄基萘的摩尔比值约为83:17,该值不随着温度和转化率的变化而改变.     

Synthesis and Catalytic Properties of ZSM-5 Zeolite with Alkyl-polyamine Triethylene-tetramine as Directing Agent

With alkyl-polyamine triethylene-tetramine as the structure-directing agent,aluminosilicate zeolite ZSM-5(MFI) crystals were synthesized and characterized by XRD,SEM,FTIR,and TG-DTA. The results indicate that the organic amine has a certain influence on the crystal shape and size. The alkaline condition was in favor of the crystallization of ZSM-5 zeolite in the triethylene-tetramine system. The catalytic activity of as-synthesized crystals was examined for the aqueous hydroxylation of phenol with hydrogen ...