Thermal treatment effect on nanostructured TiO2 films deposited using diethanolamine stabilized precursor sol

A clear ethanol based precursor sol obtained using diethanolamine has been utilized for the deposition of TiO₂ films annealed at different temperatures. The influence of annealing temperature on the structural, optical and electrochemical properties of TiO₂ thin films has been examined. Diethanolamine stabilizes the precursor sol due to its chelate forming ability with the alkoxides. It reacts as a tridentate ligand with the titanium isopropoxide. The threshold for the onset of crystallization in the films is identified at a temperature of 300 °C. The SEM study on the films elucidates segregation of irregularly shaped features into finer round clusters as a function of annealing temperature. As determined from the AFM study, the roughness parameter in the films has shown an increase with the annealing temperature. Photoluminescence measurements have given an indirect evidence for the presence of stoichiometric titanium oxide in the films. An optimum crystallite size and high ion storage capacity in the 300 °C annealed film has led to its superior electrochromic activity with the transmission modulation and coloration efficiency of the same film being 42% and 8.1 cm² C⁻¹, respectively at 550 nm. The highest degree of porosity in the 300 °C annealed film as established from the SEM study is also the reason behind its best electrochromic performance. In addition, the 300 °C annealed film also exhibits the fastest coloration switching kinetics.     

Synthesis and characterization of highly stable optically passive CeO2-ZrO2 counter electrode

Transparent and adherent CeO₂-ZrO₂ thin films having film thicknesses ∼543-598 nm were spray deposited onto the conducting (fluorine doped tin oxide coated glass) substrates from a blend of equimolar concentrations of cerium nitrate hexahydrate and zirconium nitrate having different volumetric proportions (0-6 vol.% of Zr) in methanol. CeO₂-ZrO₂ films were polycrystalline with cubic fluorite crystal structure and the crystallinity was improved with increasing ZrO₂ content. Films were highly transparent (T ∼ 92%), showing decrease in band gap energy from 3.45 eV for pristine CeO₂ to 3.08-3.14 eV for CeO₂-ZrO₂ films. The different morphological features of the film obtained at various CeO₂-ZrO₂ compositions had pronounced effect on the ion storage capacity and electrochemical stability. CeO₂-ZrO₂ film prepared at 5 vol.% Zr concentration exhibited higher ion storage capacity of 24 mC cm⁻² and electrochemical stability of 10,000 cycles in 0.5 M LiClO₄ + PC electrolyte due to its film thickness (584 nm) coupled with relatively larger porosity (8%). The optically passive behavior of such CeO₂-ZrO₂ film (with 5 vol.% Zr) is affirmed by its negligible transmission modulation irrespective of repeated Li⁺ and electron insertion/extraction. The coloration efficiency of spray deposited WO₃ thin film is found to enhance from 47 to 107 cm² C⁻¹ when CeO₂-ZrO₂ is coupled as a counter electrode with WO₃ in an electrochromic device (ECD). These films can be used as stable ‘passive’ counter electrodes in electrochromic smart windows as they retain full transparency in both the oxidized and reduced states and ever-reported longevity.     

A comparative study on IrO2-Ta2O5 coated titanium electrodes prepared with different methods

The electrodes of IrO₂-Ta₂O₅ coated titanium were prepared using conventionally thermal decomposition procedure and polymer sol-gel (Pechini) method, respectively. The microstructure and electrochemical properties of the electrodes were studied with scanning electron microscope (SEM), energy dispersive X-ray (EDX), atomic force microscope (AFM), potentiodynamic polarization, cyclic voltammetry, electrochemical impedance spectroscopy and accelerated life test. As compared with the electrode formed using the traditional method of thermal decomposition, the oxide electrode prepared by Pechini method presents morphology of higher nano-scale roughness and more uniform surface composition with little precipitates. It also has larger electrochemically active surface area, better electrocatalytic activity for oxygen evolution and higher stability.     

Single step electrosynthesis of Cu2ZnSnS4 (CZTS) thin films for solar cell application

The Cu₂ZnSnS₄ (CZTS) thin films have been electrodeposited onto the Mo coated and ITO glass substrates, in potentiostatic mode at room temperature. The deposition mechanism of the CZTS thin film has been studied using electrochemical techniques like cyclic voltammetery. For the synthesis of these CZTS films, tri-sodium citrate and tartaric acid were used as complexing agents in precursor solution. The structural, morphological, compositional, and optical properties of the CZTS thin films have been studied using X-ray diffraction (XRD), scanning electron microscopy (SEM), EDAX and optical absorption techniques respectively. These properties are found to be strongly dependent on the post-annealing treatment. The polycrystalline CZTS thin films with kieserite crystal structure have been obtained after annealing as-deposited thin films at 550 in Ar atmosphere for 1 h. The electrosynthesized CZTS film exhibits a quite smooth, uniform and dense topography. EDAX study reveals that the deposited thin films are nearly stoichiometric. The direct band gap energy for the CZTS thin films is found to be about 1.50 eV. The photoelectrochemical (PEC) characterization showed that the annealed CZTS thin films are photoactive.     

Structure and properties of PbO2-CeO2 anodes on stainless steel

The lack of ideal anodes with excellent activity and stability is one of the critical problems in electrochemical oxidation for organic wastewater treatment. It is reported in this paper that the PbO₂-CeO₂ films electrodeposited on stainless steel were used as catalytic electrodes for treating antibiotic wastewater. The PbO₂-CeO₂ films on stainless steel were proved to be high stability, good activity and relatively low cost. Because of these properties, the films are more attractive than any other electrocatalytic materials among conventional dimensionally stable anodes (DSA). Experimental results showed that the PbO₂-CeO₂ electrode has a service life of 1100 h in 3 M H₂SO₄ solution under a current density of 1 A cm⁻² at 35 °C, compared with 300 h for PbO₂ under the same conditions. The X-ray diffraction (XRD) patterns and SEM images indicated that the PbO₂-CeO₂ films on stainless steel have a dense structure and the preferred crystalline orientation on the substrate surface was changed. Color and chemical oxygen demand (COD) of antibiotics wastewater were studied by electrolysis by using these electrodes as anode and stainless steel as cathode. The results indicated that the anodes have excellent activity in antibiotic wastewater treatment. The PbO₂-CeO₂ electrodes have high chemical stability which contributed by the superstable nature of the electrode, dense microstructure, good conductivity and the improvement of bonding with the stainless steel during electrodeposition.     

基于WO3-MoO3和TiO2/CdS复合电极的光电致变色器件

电致变色广泛应用于智能窗领域,但电致变色材料仍需外部电源驱动,将太阳能电池与电致变色材料结合起来的光电致变色器件可实现无需外部供电的智能变色调控。性能优异的变色阴极和光阳极是当下光电致变色器件的研究热点。通过水热法制备WO₃-MoO₃薄膜,研究其电致变色性能;通过水热法结合连续离子层沉积法制备TiO₂/CdS复合薄膜,研究其光电转换性能。最后将WO₃-MoO₃薄膜和TiO₂/CdS复合薄膜分别作为光电致变色器件的变色阴极、光阳极构建WO₃/MoO₃-TiO₂/CdS光电致变色器件。WO₃/MoO₃-TiO₂/CdS光电致变色器件具有较大的光学调制范围(630nm处为41.99%)、更高的着色效率(35.787%),将其作为智能窗应用在现代建筑、通行工具等领域具有重要应用价值。     

Improving electrochromic behavior of spray pyrolised WO3 thin solid films by Mo doping

The effects of molybdenum [Mo] doping on the electrochromic behavior of spray pyrolised tungsten trioxide [WO₃] thin films have been studied. It has been observed that the color-bleaching kinetics, coloration efficiency, and stability of electrochromic WO₃ films are closely related to molybdenum doping concentration, apart from their microstructure and crystallinity. While a nominal 6.0 at.% molybdenum doping produces best electrochromic response in WO₃ films, the electrochemical stability is highest when the nominal concentration of molybdenum is about 2.0 at.%. The improved electrochromic behavior of the Mo doped WO₃ films has been explained from the improved H⁺ ion diffusion coefficient in the films during coloration and decoloration process.     

Deposition of thin TiO2 layers on platinum by means of cyclic voltammetry of selected complex Ti(IV) media leading to anatase

Thin layers of anatase TiO₂, up to 1 μm, were produced on the surface of a platinum electrode by means of cycling voltammetry from the aqueous solutions of the peroxo-oxalate complexes and the oxalate complexes of titanium(IV). Mechanisms of TiO₂ electrodeposition as well as different electrochemical reactions causing pH changes at the electrode were studied. The electroreduction processes of hydrogen peroxide and nitrite ion on platinum cause the highest pH changes. Values of the molar ratio of Ti(IV)/H₂O₂ should be kept closely to 0.5.In all cases studied, the electrodeposition led to the partially decomposed amorphous oxalate compounds of titanium(IV), which can be converted into crystalline anatase above 500 °C in air. The thermal behaviour of TiO₂ precursor compounds was examined by DRIFTS and TG-DTA methods. Strong effects of K⁺ and NH₄⁺ ions on the electrodeposition process were found by using of the EQCM technique, Raman spectroscopy and XRD measurements. The ammonium electrolyte warrants purity of the anatase phase.Morphology of the oxide films produced in different solvents was examined by SEM.     

Optimization of microwave synthesis of Li[Ni0.4Co0.2Mn0.4]O2 as a positive electrode material for lithium batteries

A positive electrode material for lithium ion battery applications was successfully synthesized using microwave irradiation. This microwave synthesis has several merits such as homogeneity of final product and much shorter reaction time compared to conventional synthetic methods. We synthesized spherical [Ni_0.4Co_0.2Mn_0.4](OH)₂ as a precursor by a co-precipitation method. The pelletized mixture of the precursor and lithium hydroxide was calcined under different reaction times and temperatures by applying 1200 W of microwave irradiation at 2.45 GHz. We determined the optimum conditions of microwave synthesis for positive electrode materials. The powders were characterized by X-ray diffraction, scanning electron microscopy, and electrochemical testing. The capacity, its retention, and thermal stability of Li[Ni_0.4Co_0.2Mn_0.4]O₂ synthesized by the microwave synthesis were comparable to the Li[Ni_0.4Co_0.2Mn_0.4]O₂ prepared by the high temperature calcination method.     

Inkjet printing of photocatalytically active TiO2 thin films from water based precursor solutions

In this work, aqueous chemical solution deposition route suited for inkjet printing is used for the synthesis of photocatalytically active TiO₂ coatings. Environmentally friendly precursor solutions with electromagnetic ink-jet printing, allows cheap and simple processing of TiO₂ films on glass. The hydrolysis reaction of water sensitive titanium alkoxide (Ti-alkoxide) precursor is controlled by adding complexing agents as citric acid and triethanolamine prior to water addition, and aqueous stable solutions are achieved. The pH of the solutions is brought to neutral to guarantee flexible processing, avoid damage to substrates and equipment. Solution parameters are adapted to obtain optimal gelation conditions and good jettability. The influence of processing parameters on the phase formation and surface morphology is studied by thermogravimetric analysis and differential thermal analysis (TGA/DTA), X-ray diffraction (XRD), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The photocatalytic activity of the films is evaluated by the degradation of methyl orange.     

Enhanced inactivation of E. coli bacteria using immobilized porous TiO2 photoelectrocatalysis

Immobilized TiO₂ nanotube electrodes with high surface areas were grown via electrochemical anodization in aqueous solution containing fluoride ions for photocatalysis applications. The photoelectrochemical properties of the grown immobilized TiO₂ film were studied by potentiodynamic measurements (linear sweep voltammetry), in addition to the calculation of the photocurrent response. The nanotube electrode properties were compared to mesoporous TiO₂ electrodes grown by anodization in sulfuric acid at high potentials (above the microsparking potential) and to 1 g/l P-25 TiO₂ powder. Photocatalyst films were evaluated by high resolution SEM and XRD for surface and crystallographic characterization. Finally, photoelectrocatalytic application of TiO₂ was studied via inactivation of E. coli. The use of the high surface area TiO₂ nanotubes resulted in a high photocurrent and an extremely rapid E. coli inactivation rate of ∼10⁶ CFU/ml bacteria within 10 min. The immobilized nanotube system is proven to be the most potent electrode for water purification.     

Electrochemical oxidation of ammonia (NH4/NH3) on thermally and electrochemically prepared IrO2 electrodes

The electrochemical oxidation of ammonia (NH₄⁺/NH₃) in sodium perchlorate was investigated on IrO₂ electrodes prepared by two techniques: the thermal decomposition of H₂IrCl₆ precursor and the anodic oxidation of metallic iridium. The electrochemical behaviour of Ir(IV)/Ir(III) surface redox couple differs between the electrodes indicating that on the anodic iridium oxide film (AIROF) both, the surface and the interior of the electrode are electrochemically active whereas on the thermally decomposed iridium oxide films (TDIROF), mainly the electrode surface participates in the electrochemical processes.On both electrodes, ammonia is oxidized in the potential region of Ir(V)/Ir(IV) surface redox couple activity, thus, may involve Ir(V). During ammonia oxidation, TDIROF is deactivated, probably by adsorbed products of ammonia oxidation. To regenerate TDIROF, it is necessary to polarize the electrode in the hydrogen evolution region. On the contrary, AIROF seems not to be blocked during ammonia oxidation indicating its fast regeneration during the potential scan. The difference between both electrodes results from the difference in the activity of the iridium oxide surface redox couples.     

A study of lithium insertion into MnO2 containing TiS2 additive a battery material in aqueous LiOH solution

The electrochemical behavior and surface characterization of manganese dioxide (MnO₂) containing titanium disulphide (TiS₂) as a cathode in aqueous lithium hydroxide (LiOH) electrolyte battery have been investigated. The electrode reaction of MnO₂ in this electrolyte is shown to be lithium insertion rather than the usual protonation. MnO₂ shows acceptable rechargeability as the battery cathode. The influence of TiS₂ (1, 3 and 5 wt%) additive on the performance of MnO₂ as a cathode has been determined. The products formed on reduction of the cathode material have been characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS), fourier transform infrared spectroscopy (IR) and transmission electron microscopy (TEM). It is found that the presence of TiS₂ to ≤3 wt% improves the discharge capacity of MnO₂. However, increasing the additive content above this amount causes a decrease in its discharge capacity.     

Cerium salt activated nanoparticles as fillers for silane films: Evaluation of the corrosion inhibition performance on galvanised steel substrates

The present work investigates the electrochemical behaviour of galvanised steel substrates pre-treated with bis-[triethoxysilylpropyl] tetrasulfide silane (BTESPT) solutions modified with SiO₂ or CeO₂ nanoparticles activated with cerium ions. The electrochemical behaviour of the pre-treated substrates was evaluated via electrochemical impedance spectroscopy in order to assess the role of the nanoparticles in the silane film resistance and capacitance. The ability of the Ce-activated nanoparticles to mitigate corrosion activity at the microscale level in artificial induced defects was studied via scanning vibrating electrode technique (SVET). Complementary studies were performed using potentiodynamic polarisation. The results show that the presence of nanoparticles reinforces the barrier properties of the silane films and that a synergy seems to be created between the activated nanoparticles and the cerium ions, reducing the corrosion activity. The addition of CeO₂ nanoparticles was more effective than the addition of SiO₂ nanoparticles.     

Electrochemical behaviors of graphene-ZnO and graphene-SnO2 composite films for supercapacitors

Graphene, graphene-ZnO and graphene-SnO₂ films were successfully synthesized and used as electrode materials for electrochemical supercapacitors, respectively. The screen-printing approach was employed to fabricate graphene film on graphite substrate while the ZnO and SnO₂ were deposited on graphene films by ultrasonic spray pyrolysis. The electrochemical performances of these electrodes were comparatively analyzed through electrochemical impedance spectrometry, cyclic voltammetry and chronopotentiometry tests. The results showed that the incorporation of ZnO or SnO₂ improved the capacitive performance of graphene electrode. Graphene-ZnO composite electrode exhibited higher capacitance value (61.7 F/g) and maximum power density (4.8 kW/kg) as compared with graphene-SnO₂ and pure graphene electrodes.     

Semiconductor oxide based electrodes for the label-free electrical detection of DNA hybridization: Comparison between Sb doped SnO2 and CdIn2O4

First results are reported regarding the design, fabrication and operation of a DNA biochip based on a semiconductor oxide electrode that employs label-free electrical detection of the DNA hybridization. The same process of DNA functionalisation, including hydroxylation and silanization steps, was performed on two types of semiconductor oxide: Sb doped SnO₂ and CdIn₂O₄ thin films. These oxide electrodes were laboratory-made films deposited on glass substrates using a chemical vapour deposition method, i.e. the aerosol pyrolysis technique. After having characterized some physico-chemical properties of the bare films, the label-free electrical DNA hybridization detection, without redox couple labelling, was performed using electrochemical impedance spectrometry (EIS) before and after hybridization. On both oxides, over a large frequency range, a significant increase in the impedance modulus was obtained. The increase in the case of CdIn₂O₄ was by a factor of 2.1 ± 0.5 and in the case of Sb doped SnO₂ was by a factor of 1.6 ± 0.1. This phenomenon was especially marked on CdIn₂O₄ thin films, which exhibit a higher sensitivity to the surface event. The DNA hybridization to complementary DNA targets labelled with fluorescent markers was confirmed using fluorescence microscopy.     

TiO2, TiO2/Ag and TiO2/Au photocatalysts prepared by spray pyrolysis

TiO₂, TiO₂/Ag and TiO₂/Au photocatalysts exhibiting a hollow spherical morphology were prepared by spray pyrolysis of aqueous solutions of titanium citrate complex and titanium oxalate precursors in one-step. Effects of precursor concentration and spray pyrolysis temperature were investigated. By subsequent heat treatment, photocatalysts with phase compositions from 10 to 100% rutile and crystallite sizes from 12 to 120 nm were obtained. A correlation between precursor concentration and size of the hollow spherical agglomerates obtained during spray pyrolysis was established. The anatase to rutile transformation was enhanced with metal incorporations and increased precursor concentration. The photocatalytic activity was evaluated by oxidation of methylene blue under UV-irradiation. As-prepared TiO₂ particles with large amounts of amorphous phase and organic residuals showed similar photocatalytic activity as the commercial Degussa P25. The metal incorporated samples showed comparable photocatalytic activity to the pure TiO₂ photocatalysts.     

The investigation on electrochemical reaction mechanism of CuF2 thin film with lithium

Crystalline CuF₂ thin films were prepared by pulsed laser deposition under room temperature. The physical and electrochemical properties of the as-deposited thin films have been investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), galvanostatic cycling and cyclic voltammetry (CV). Reversible capacity of 544 mAh g⁻¹ was achieved in the potential range of 1.0–4.0 V. A reversible couple of redox peaks at 3.0 V and 3.7 V was firstly observed. By using ex situ XRD and TEM techniques, an insertion process followed by a fully conversion reaction to Cu and LiF was revealed in the lithium electrochemical reaction of CuF₂ thin film electrode. The reversible insertion reaction above 2.8 V could provide a capacity of about 125 mAh g⁻¹, which makes CuF₂ a potential cathode material for rechargeable lithium batteries.     

Synthesis of SnO2/Mg2SnO4 nanoparticles and their electrochemical performance for use in Li-ion battery electrodes

Uniform crystalline MgSn(OH)₆ nanocubes were synthesized by a hydrothermal method. The influences of reaction conditions were investigated and the results showed that the solvent constituents significantly affected the shape and size of MgSn(OH)₆·SnO₂/Mg₂SnO₄ has been obtained by thermal treatment at 850 °C for 8 h under a nitrogen atmosphere using MgSn(OH)₆ as the precursor. The electrochemical tests of SnO₂/Mg₂SnO₄ revealed that SnO₂/Mg₂SnO₄ has a higher capacity and better cyclability compared to pure SnO₂ or Mg₂SnO₄. The electrochemical performance of SnO₂/Mg₂SnO₄ was sensitive to the size of the nanoparticles. The lithium-driven structural and morphological changes of the electrode after cycling were also studied by the ex-situ XRD pattern and TEM tests. This work indicates that SnO₂/Mg₂SnO₄ is a promising anode material candidate for application in Li-ion batteries.     

Synthesis and characterization of mesoporous TiO2 nanostructured films prepared by a modified sol-gel method for application in dye solar cells

Anatase TiO₂ colloidal dispersions were obtained by hydrothermal synthesis at 200 °C from titanium isopropoxide gels modified with acetic acid in the presence of a non-ionic surfactant. Absolute ethanol, anhydrous terpineol and ethyl cellulose were added to this anatase dispersion resulting in a 23 wt% TiO₂ paste. Mesoporous films for application as working electrodes in dye-sensitized solar cells were prepared by the screen-printing method, yielding reproducible films with thicknesses about 10 μm and desired porosity levels in a single printing operation. An average energy conversion efficiency of 5.2%, and a fill factor of 0.66 were achieved with anatase particle sizes ranging between 15 and 20 nm. The reproducibility of the results was confirmed by electrochemical impedance spectroscopy analysis.