Dy(Ⅲ)离子在LiCl-KCl熔盐中的电化学行为及Dy-Ni金属间化合物的选择性制备

采用循环伏安、方波伏安和开路计时电位等电化学方法研究了Dy(Ⅲ)离子在LiCl-KCl 共晶盐中的电化学行为及Dy-Ni 合金形成的电化学机理. 循环伏安和方波伏安法研究表明, Dy(Ⅲ)离子的电化学还原过程为三个电子转移的一步反应. 与惰性W电极相比, Dy(Ⅲ) 离子在Ni 电极上的循环伏安曲线多出了三对氧化还原峰,是由于Dy与Ni 形成了合金化合物, 导致Dy(Ⅲ)离子在活性Ni 电极发生了欠电位沉积. 采用X射线衍射(XRD)和扫描电子显微镜(SEM)附带能量散射谱(EDS)对恒电位(-1.6, -1.8 和-2.0 V)电解制备的Dy-Ni 合金进行分析, 分别获得了DyNi₅, Dy₂Ni₇和DyNi₂金属间化合物. 实验结果表明, 通过控制电位进行恒电位电解可以有选择性地制备不同的金属间化合物.     

LiCl-KCl熔盐体系中镨(Ⅲ)在镍电极上的电化学行为

采用循环伏安、 方波伏安、 计时电位和开路计时电位等电化学方法研究了Pr(Ⅲ)离子在共晶LiCl-KCl熔盐中Ni电极上的电化学行为及Pr-Ni合金化机理. 结果表明, Pr(Ⅲ)离子的电化学还原过程为三电子转移的一步反应. 与惰性Mo电极上的循环伏安曲线相比, Pr(Ⅲ) 离子在活性Ni电极的循环伏安曲线上还出现了4对氧化还原峰, 表明Pr(Ⅲ)离子在Ni电极上发生欠电位沉积, 是由于生成不同的Pr-Ni金属间化合物. 采用X射线衍射仪和扫描电子显微镜-能谱仪等对恒电位电解的产物进行了表征. 结果表明, 在不同电位下进行恒电位电解时, 每个电位上只得到一种Pr-Ni金属间化合物, 分别为PrNi₂, PrNi₃, Pr₂Ni₇和PrNi₅.     

Pr(Ⅲ)离子在LiCl-KCl熔体中Bi膜W电极上的电化学行为

采用循环伏安、方波伏安、计时电位和开路计时电位等电化学方法研究了Pr（Ⅲ）离子在LiCl-KCl-BiCl₃熔体中W电极上的电化学行为。循环伏安和方波伏安的研究表明,Pr在预先沉积的Bi膜电极上发生欠电位沉积是由于生成了Pr-Bi金属间化合物,导致Pr（Ⅲ）在Bi膜电极上的还原电位比在W电极上还原电位更正。从开路计时电位曲线可以观察到两相共存的Pr-Bi金属间化合物的两个平台。利用开路计时电位计算了723-873 K温度范围内Pr在Pr-Bi合金中的活度和偏摩尔Gibbs自由能以及Pr-Bi金属间化合物的生成Gibbs自由能。通过恒电位电解,在液态Bi电极上得到了Pr-Bi合金,并采用X射线衍射（XRD）和扫描电子显微镜（SEM）附带能量散射谱（EDS）对样品进行了表征,结果表明所得到的Pr-Bi金属间化合物为PrBi₂和PrBi。     

在LiCl-KCl-ZnCl_2熔盐体系中电化学共还原提取钕

针对镧系元素钕,本文通过循环伏安、开路计时电位、方波伏安等方法研究了773 K时Nd(III)在钼电极上在LiCl-KCl-ZnCl2熔盐体系中的电化学行为及Zn-Nd合金的形成过程.结果表明:在LiCl-KCl-ZnCl2熔盐中,Nd(III)在预先沉积的Zn阴极上欠电位沉积形成三种Zn-Nd金属间化合物.基于电化学行为研究,采用恒电位电解提取Nd并用方波伏安曲线测量来检测Nd(III)离子浓度的变化,然后通过电解前后Nd(III)离子浓度变化评估了Nd的电解提取效率.实验结果表明:-1.84 V恒电位电解进行50 h后,Nd(III)离子浓度接近于零,提取效率为99.67%.在973 K时通过恒电流电解提取Nd并获得了Zn-Nd合金,通过X射线衍射(XRD)和扫描电子显微镜(SEM)附带能量散射谱(EDS)对合金的相组成和微观形貌进行了分析.XRD分析表明在Zn-Nd合金中存在Nd2Zn17,LiZn和Zn相,EDS能谱分析表明Nd在合金中的原子分数高达14.99%.     

在LiCl-KCl-ZnCl2熔盐体系中电化学共还原提取钕

针对镧系元素钕,本文通过循环伏安、开路计时电位、方波伏安等方法研究了773 K时Nd（Ⅲ）在钼电极上在LiCl-KCl-ZnCl₂熔盐体系中的电化学行为及Zn-Nd合金的形成过程. 结果表明：在LiCl-KCl-ZnCl₂熔盐中,Nd（Ⅲ）在预先沉积的Zn 阴极上欠电位沉积形成三种Zn-Nd金属间化合物. 基于电化学行为研究,采用恒电位电解提取Nd并用方波伏安曲线测量来检测Nd（Ⅲ）离子浓度的变化,然后通过电解前后Nd（Ⅲ）离子浓度变化评估了Nd的电解提取效率. 实验结果表明：-1.84 V恒电位电解进行50 h后,Nd（Ⅲ）离子浓度接近于零,提取效率为99.67%. 在973 K时通过恒电流电解提取Nd并获得了Zn-Nd合金,通过X射线衍射（XRD）和扫描电子显微镜（SEM）附带能量散射谱（EDS）对合金的相组成和微观形貌进行了分析. XRD分析表明在Zn-Nd合金中存在Nd₂Zn₁₇,LiZn 和Zn相,EDS能谱分析表明Nd在合金中的原子分数高达14.99%.     

LiCl-KCl-LaCl3熔盐体系中La(III)的电化学行为

在773 K条件下,研究了La（III）在LiCl-KCl熔盐中W和Ni电极上的电化学行为。La（III）还原反应是一步三电子转移的准可逆反应;通过在Ni电极上直接电沉积La的方法可以获得La-Ni金属间化合物;恒电位电解可以获得含三种金属间化合物（LaNi₅、La₇Ni₁₆和La₂Ni₃）的La-Ni合金层,并且通过X射线衍射仪（XRD）和扫描电镜-能谱分析仪（SEM-EDS）确定物相并表征结构。采用开路计时电位法估算了LaNi₅金属间化合物的标准生成吉布斯自由能。揭示了恒电位电解方法是制备La-Ni镀层合金以及提取熔盐中La的有效方法。     

Electrochemical behaviour of lanthanum fluoride in molten fluorides

The electrochemical behaviour of lanthanum fluoride dissolved in molten lithium fluoride and in eutectic mixture LiF-CaF₂ was investigated by cyclic voltammetry and laboratory electrolysis. The cyclic voltammetry experiments were carried out at 900°C and 800°C, respectively, in a graphite crucible (counter electrode). Several types of working electrodes (Mo, W, Ni and Cu) were used. Ni/Ni(II) was used as a reference electrode. Laboratory electrolysis was carried out in the system LiF-CaF₂-LaF₃ at 800°C in galvanostatic (j _c = −0.21 A cm⁻²) and potentiostatic (E = 0.87 V) regimes. In both cases, nickel served as the cathode and graphite as the anode. It was found that no new separate reduction peak occurred on the molybdenum or tungsten electrodes in the investigated systems. When copper or nickel electrodes were used, new peaks corresponding to the reduction of lanthanum(III) to lanthanum metal appeared. This can be explained by the formation of alloys or intermetallic compounds of lanthanum with copper or nickel. X-ray microanalysis showed that lanthanum was electrodeposited together with calcium under formation of intermetallic compounds with the electrode materials in the galvanostatic regime. In the potentiostatic regime, mainly lanthanum was deposited, which enabled its separation.     

铝电极在LiNO3-KNO3熔盐中的电化学行为

采用循环伏安和恒电位电解法考察了铝电极在LiNO3-KNO3熔盐中的电化学行为. 实验结果表明, 在该熔盐中, 锂离子在铝电极上的电还原过程伴随着新生态的锂原子向电极内部的随后扩散步骤; 锂原子进入铝电极后与铝发生合金化, 形成β-LiAl合金和γ-LiAl合金; 锂离子在铝电极上的还原过程受还原态锂在铝基体内的扩散步骤控制. 循环伏安实验发现, 铝电极在该熔盐中的氧化和还原峰电流都先随循环次数增加而增大, 最后基本上趋于稳定. 这表明铝电极在该熔盐体系中具有较好的电化学稳定性.     

TiO_2纳米管电极上电化学还原CO_2生成CH_3OH

采用原位阳极氧化-煅烧法制备TiO_2纳米管(TiO_2NTs)电极,运用X射线衍射(XRD)、电场发射扫描电子显微镜(FESEM)、X射线光电子能谱(XPS)、双电位阶跃测试等对制备电极进行表征,考察了其在0.1mol?L~(-1) KHCO_3水溶液中电化学还原CO_2的催化活性。结果表明TiO_2NTs电极上电化学还原CO_2的主产物为CH_3OH,CH_3OH由HCOOH和HCHO进一步还原而来。电极制备的最佳煅烧温度为450℃(TiO_2NTs-450),电解电位-0.56 V(vs RHE(可逆氢电极))时反应120 min后,生成CH_3OH的法拉第效率和分电流密度分别为85.8%和0.2 m A?cm~(-2)。与550和650℃煅烧的电极相比,TiO_2NTs-450电极具有更高的催化活性,归因于电极表面更多的三价钛活性位,有利于CO_2吸附,从而对·CO_2-起到稳定的作用,速率控制步骤转变为·CO_2-的质子化反应。     

Electrochemical Co-reduction of Bi(Ⅲ)and Y(Ⅲ)and Extracting Yttrium from Molten LiCl-KCl Using Liquid Bi as Cathode

The electrochemical reaction of Bi(Ⅲ)and co-reduction behaviour of Bi(Ⅲ)and Y(Ⅲ)ions were researched in molten LiCl-KCl on a ttmgsten(W)electrode employing a range of electrochemical teclmiques.Cyclic voltammetric and square-wave voltanunetric results revealed that the reduction of Bi(Ⅲ)was a one-step process,with the exchange of three electrons on a W electrode,and diffusion-controlled.The electrochemical curves showed two reduction peaks pertaining to the formation of Bi-Y alloy compounds,because of the co-reduction of Bi(Ⅲ)and Y(Ⅲ) by metallic Y deposited on the pre-deposited Bi-coated W electrode and reacting with Bi metal in molten LiCl-KCl. Furthermore,galvanostatic electrolysis was conducted using liquid Bi as cathode to extract yttrium at different current intensities,and the extractive products were analyzed by SEM,EDS and XRD.The results indicated that BiY intermetallic compotmd was formed in the molten LiCl-KCl-YCl3 system.     

Cr2O3粉末在CaCl2熔盐中直接电化学还原的金属通腔电极研究

应用金属通腔电极研究Cr2O3粉末于熔盐中的电化学行为,验证了900℃下Cr2O3粉末在含镁量<0.005%氯化钙熔盐中的分步还原机理,估算其电化学还原动力学参数;并由扫描电镜观察产物形貌,分析电解电位和时间对金属颗粒尺寸的影响.     

KCl-MgCl2-K2ZrF6-ZrO2熔盐体系中Mg-Zr合金的制备

在1023 K条件下,开展了Zr（IV）在KCl-MgCl₂-K₂ZrF₆和KCl-MgCl₂-K₂ZrF₆-ZrO₂熔盐中Mo电极上的电化学实验,并获得如下结果：Zr（IV）还原为Zr（0）是通过两步反应,即Zr（IV）+ 2e^- → Zr（II）和Zr（II）+2e^- → Zr（0）。两个反应是准可逆的。KCl-MgCl₂-K₂ZrF₆-ZrO₂熔盐中的电极反应表明在预沉积的Zr上欠电位沉积Mg可以用来制备Mg-Zr合金。感应耦合离体子体-原子发射光谱（ICP-AES）分析结果表明,在1023 K和KCl-MgCl₂-K₂ZrF₆-ZrO₂熔盐中K₂ZrF₆含量在9.2%（w）条件下,恒电流电解获得的Mg-Zr合金中Zr含量可以达到7.2%（w）。并采用X射线衍射（XRD）和扫描电镜-能谱仪（SEM-EPS）对合金进行表征。利用KCl、MgCl₂、K₂ZrF₆、KF和ZrO₂为原料,直接恒电流电解制备Mg-Zr合金是可行的,且在确定反应条件下实现合金中Zr含量可控;揭示了KCl-MgCl₂熔盐体系可以实现Mg和Zr的共电沉积,并且验证了直接电解ZrO₂获得Mg-Zr合金的可行性。     

NaCl-KCl熔盐体系中AlF3氟化Tb4O7电化学制备Al-Tb合金

在NaCl-KCl-Tb₄O₇-AlF₃体系中为了制备Al-Tb合金,首先对熔盐中的上清液和沉淀物进行了分析,X射线衍射（XRD）结果确定了Tb₄O₇能被AlF₃氟化生成TbF₃。采用一系列的电化学方法对NaCl-KCl-AlF₃-Tb₄O₇体系在Mo电极上的电化学行为进行了研究。循环伏安、方波伏安、计时电位和开路计时电位等电化学方法的研究结果表明Tb（III）在预先沉积的Al电极上发生欠电位沉积。在不同条件下进行恒电流电解制备了Al-Tb合金,并对所得合金样品进行XRD和扫描电镜-能量散射谱（SEM-EDS）表征。结果表明在-2.5 A进行恒电流电解得到的Al-Tb合金是由Al和Al₃Tb两相组成。采用电感耦合等离子体-原子发射光谱仪（ICP-AES）对实验所得沉积物的组成进行分析,研究了电解条件对合金组成和电流效率的影响。在电流强度为-1.5 A进行恒电流电解2 h,电流效率可达76.5%。     

Electrochemical Degradation of o-Chloronitrobenzene by Three-dimensional Electrodes

Degradation of o-chloronitrobenzene wastewater was experimentally investigated at a three-dimensional electrode(TDE) with granular activated carbon as the particle electrode, graphite as the anode, and stainless steel plate as the cathode. The kinetic model of o-chloronitrobenzene degradation was studied, and the effects of pH, electrolysis time, particle electrode, electrolyte concentration, and initial concentration of the solution on degradation efficiency were investigated to determine the optimal operating conditions. The degradation of o-chloronitrobenzene by oxidation at the TDE was monitored by chemical oxygen demand(COD) measurements, UV-Vis absorption, and high performance liquid chromatography(HPLC). COD degradation by electrochemical degradation followed pseudo-first order kinetics with respect to the concentration of o-chloronitrobenzene solutions. Optimal reaction conditions included 15 g of activated carbon as the particle electrode, 400 mg/L o-chloronitrobenzene solution containing 0.10 mol/L Na₂SO₄, pH=3, and 60 min of electrolysis. The UV-Vis absorption spectra and HPLC results illustrate that the benzene ring in o-chloronitrobenzene was rapidly broken down to form aliphatic substances through electrochemical degradation. COD degradation was approximately 98.5% at optimal conditions.     

Ni-Co/RuO2复合电极的制备及其电催化析氢性能

采用快速凝固结合去合金化的方法制备纳米多孔Ni-Co合金,利用RuO_2对Ni-Co合金进行表面修饰,通过X射线衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)对多孔材料进行物相分析和形貌表征,并通过线性扫描伏安法、多电位阶跃法、交流阻抗法和恒电流电解法测试多孔电极的电催化析氢性能。结果表明,Ni-Co/RuO_2复合电极材料在50 mA·cm~(-2)电流密度下析氢过电位为180 mV,析氢过程由Volmer-Heyrovsky步骤控制,交换电流密度为4.42 mA·cm~(-2),经10 h恒电流电解后电位仅增加20 mV,表现出良好的析氢稳定性。     

吡唑基镁卤化物/四氢呋喃可充镁电池电解液

将不同配比的吡唑与格氏试剂反应制得的吡唑基镁卤化物/四氢呋喃(THF)溶液用作可充镁电池电解液,采用循环伏安和恒电流充放电测试研究了该电解液的镁沉积-溶出性能和氧化分解电位;并通过X射线衍射(XRD)和扫描电镜(SEM)对沉积物的组分和形貌进行了分析.结果表明,吡唑上的取代基、吡唑与格氏试剂的反应配比对电解液的电化学性能都有影响.1 mol·L-11-甲基吡唑-PhMgCl(1:1摩尔比)/THF反应配制的电解液在不锈钢(SS)集流体的阳极氧化分解电位达到2.4 V(vs Mg/Mg2+),并具有镁沉积-溶出电位低、循环稳定性高、配制方便的特点,有希望应用于实际的可充镁电池体系中.     

双二苯基-1-甲基咪唑膦氯化镍的制备及其电催化还原CO2的研究

以二苯基-1-甲基咪唑膦（dpim）为配体制备了一种新型的配合物催化剂Ni(dpim)₂Cl₂. 循环伏安研究表明,Ni(dpim)₂Cl₂配合物在氮气气氛下表现出两步还原的电化学行为,在-0.7 V下为两电子的不可逆还原,在-1.3 V下为单电子准可逆还原. 向电解液中通入CO₂后,在-1.3 V下的还原峰变得不可逆,且其峰电流从0.48 mA·cm^-2增大到0.55 mA·cm^-2. 在质子源（CH₃OH）存在的条件下,该还原峰电流可继续增大到0.72 mA·cm^-2. 该研究结果表明,Ni(dpim)₂Cl₂配合物对CO₂还原具有良好的电催化性能,且其电催化还原过程符合ECE机理. 在-1.3 V下恒电位电解得到的还原产物主要为CO,催化转换频率（Turnover of Frenquency, TOF）为0.17 s^-1.     

FeCl2-K2MoS4体系电催化还原乙炔为乙烯

采用控电位电解、循环伏安法和交流阻抗法研究了FeCl₂-K₂MoS₄体系对乙炔在石墨电极上还原为乙烯的电催化活性及反应机理。实验结果表明,当石墨阴极的电位控制在-1.50V(vs.SCE)时,FeCl₂+K₂MoS₄的DMF溶液对C₂H₂还原为C₂H₄表现出明显的电催化活性和高的选择性。在-0.5～-1.0V时Mo(Ⅵ)还原为Mo(Ⅴ);在按连串的电子传递机理进行的Mo(Ⅴ)→Mo(Ⅲ)反应的电位区间(-1.0～-1.50V)溶液中所形成的络合品种传递电子的能力更强。Mo(Ⅲ)可能是络合物的电活性成分。     

Electrolysis of ammonia for hydrogen production catalyzed by Pt and Pt-Ir deposited on nickel foam

Electrolysis of ammonia in alkaline electrolyte solution was applied for the production of hydrogen. Both Pt-loaded Ni foam and Pt-Ir loaded Ni foam electrodes were prepared by electrodeposition and served as anode and cathode in ammonia electrolytic cell, respectively. The electrochemical behaviors of ammonia in KOH solution were individually investigated via cyclic voltammetry on three electrodes, i.e. bare Ni foam electrode, Pt-loaded Ni foam electrode and Pt-Ir loaded Ni foam electrode. The morphology and composition of the prepared Ni foam electrode were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Effects of the concentration of electrolyte solution and temperature of electrolytic cell on the electrolysis reaction were examined in order to enhance the efficiency of ammonia electrolysis. The competition of ammonia electrolysis and water electrolysis in the same alkaline solution was firstly proposed to explain the changes of cell voltage with the electrolysis proceeding. At varying current densities, different cell voltages could be obtained from galvanostatic curves. The low cell voltage of 0.58 V, which is less than the practical electrolysis voltage of water (1.6 V), can be obtained at a current density of 2.5 mA/cm². Based on some experimental parameters, such as the applied current, the resulting cell voltage and output of hydrogen gas, the power consumption per gram of H₂ produced can be estimated.     

Electrochemical Formation of Al-Li Alloys by Codeposition of Al and Li from LiCl-KCl-AlF3 Melts at 853 K

The electrochemical behavior of Al(III) ions was studied in molten LiCl-KCl melts on a molybdenum electrode. Cyclic voltammetry, chronopotentiometry and chronoamperometry were used to explore the deposition mechanism of Al and Li. Cyclic voltammetry expriment indicates that under potential deposition(UPD) of lithium on pre-deposited aluminium led to the formation of liquid Al-Li alloys at 853 K. The diffusion coefficient of Al(III) ions at 853 K in LiCl-KCl-AlF₃(1%, mass fraction) melts was determined to be (2.79±0.05)×10^?5 cm²/s. Chronopotentiograms and chronoamperograms demonstrate that the codeposition of Al(III) and Li(I) ions formed Al-Li alloys at cathodic current densities higher than ?0.28 A/cm² or cathodic potentials more negative than ?2.20 V. X-Ray diffraction(XRD) pattern indicates that Al-Li alloys with different phases formed via galvanostatic electrolysis. Inductively coupled plasma(ICP) analyses of the samples obtained by electrolysis show that lithium and aluminium contents of Al-Li alloys could be controlled by AlF₃ concentration and current intensity.