A study on the mechanism of high-lift generation by an airfoil in unsteady motion at low reynolds number

The aerodynamic force and flow structure of NACA 0012 airfoil performing an unsteady motion at low Reynolds number (Re=100) are calculated by solving Navier-Stokes equations. The motion consists of three parts: the first translation, rotation and the second translation in the direction opposite to the first. The rotation and the second translation in this motion are expected to represent the rotation and translation of the wing-section of a hovering insect. The flow structure is used in combination with the theory of vorticity dynamics to explain the generation of unsteady aerodynamic force in the motion. During the rotation, due to the creation of strong vortices in short time, large aerodynamic force is produced and the force is almost normal to the airfoil chord. During the second translation, large lift coefficient can be maintained for certain time period and , the lift coefficient averaged over four chord lengths of travel, is larger than 2 (the corresponding steady-state lift coefficient is only 0.9). The large lift coefficient is due to two effects. The first is the delayed shedding of the stall vortex. The second is that the vortices created during the airfoil rotation and in the near wake left by previous translation form a short “vortex street” in front of the airfoil and the “vortex street” induces a “wind”; against this “wind” the airfoil translates, increasing its relative speed. The above results provide insights to the understanding of the mechanism of high-lift generation by a hovering insect. The project supported by the National Natural Science Foundation of China (19725210)     

Investigation of flow field of clap and fling motion using immersed boundary coupled lattice Boltzmann method

This paper deals with the investigation of flow field due to clap and fling mechanism using immersed boundary coupled with lattice Boltzmann method. The lattice Boltzmann method (LBM), an alternative to Navier–Stokes solver, is used because of its simplicity and computational efficiency in solving complex moving boundary problems. Benchmark problems are simulated to validate the code, which is then used for simulating flow over two elliptic wing of aspect ratio 5 performing clap and fling flapping motion for different flow parameters such as Reynolds number (Re=75, 100, 150), advance ratio (J=10E−3.10E−2,0.2) and frequency (f=0.05 Hz, 0.25 Hz). Numerical simulation is able to capture typical low Reynolds number unsteady phenomena such as, ׳wake vortex wing interaction׳, ׳Kramer effect׳ and ׳delayed stall׳. The results are both qualitatively and quantitatively consistent with experimental observation. The parametric study involving different combinations of Re, f and J depict distinctly different aerodynamic performances providing physical insights into the flow physics. It is observed that a combination of low f, low J and high Re flow results in better aerodynamic performance. Pronounced lift enhancement via leading edge vortices are obtained in unsteady regime (J<1) compared to quasi-steady regime (J>1). The role of leading edge vortices in enhancing lift are investigated by studying the size and strength of these vortices for different flow conditions. For a given Re, the magnitude of maximum lift coefficient decreases with increasing f irrespective of the value of J; while the same is enhanced with the increasing Re.     

High fidelity numerical simulation of airfoil thickness and kinematics effects on flapping airfoil propulsion

High-fidelity numerical simulations with the spectral difference (SD) method are carried out to investigate the unsteady flow over a series of oscillating NACA 4-digit airfoils. Airfoil thickness and kinematics effects on the flapping airfoil propulsion are highlighted. It is confirmed that the aerodynamic performance of airfoils with different thickness can be very different under the same kinematics. Distinct evolutionary patterns of vortical structures are analyzed to unveil the underlying flow physics behind the diverse flow phenomena associated with different airfoil thickness and kinematics and reveal the synthetic effects of airfoil thickness and kinematics on the propulsive performance. Thickness effects at various reduced frequencies and Strouhal numbers for the same chord length based Reynolds number (=1200) are then discussed in detail. It is found that at relatively small Strouhal number (=0.3), for all types of airfoils with the combined pitching and plunging motion (pitch angle 20°, the pitch axis located at one third of chord length from the leading edge, pitch leading plunge by 75°), low reduced frequency (=1) is conducive for both the thrust production and propulsive efficiency. Moreover, relatively thin airfoils (e.g. NACA0006) can generate larger thrust and maintain higher propulsive efficiency than thick airfoils (e.g. NACA0030). However, with the same kinematics but at relatively large Strouhal number (=0.45), it is found that airfoils with different thickness exhibit diverse trend on thrust production and propulsive efficiency, especially at large reduced frequency (=3.5). Results on effects of airfoil thickness based Reynolds numbers indicate that relative thin airfoils show superior propulsion performance in the tested Reynolds number range. The evolution of leading edge vortices and the interaction between the leading and trailing edge vortices play key roles in flapping airfoil propulsive performance.     

褶皱幅度对仿生翼型滑翔气动特性的影响

蜻蜓翅膀具有独特的褶皱状形貌．研究者们致力于利用仿生学原理,设计在低雷诺数条件下具有更优气动性能的褶皱翼型．本文采用计算流体力学方法,求解二维不可压Navier-Stokes方程组,探讨了四种翼型（平板翼型、流线翼型、小幅度褶皱翼型和大幅度褶皱翼型）的气动表现．在低雷诺数条件下得到以下结果：(1) 较小幅度的褶皱结构有利于增加升力和减小阻力．(2) 雷诺数变化时褶皱翼型的升力系数呈非线性变化;在特定雷诺数区间,幅度相近的褶皱翼型会发生相对气动优势的转变．(3) 褶皱结构内的回流区通过减小粘性阻力,使得翼型总阻力下降．(4) 翼型前缘的极小区域会产生脉冲高升力,对升力表现产生较大影响．这些结果表明,调整褶皱幅度是实现褶皱翼型气动优化的有效方案．     

Numerical analysis of active chordwise flexibility on the performance of non-symmetrical flapping airfoils

This paper investigates the effect of active chordwise flexing on the lift, thrust and propulsive efficiency of three types of airfoils. The factors studied are the flexing center location, standard two-sided flexing as well as a type of single-sided flexing. The airfoils are simulated to flap with four configurations, and the effects of flexing under these configurations are investigated. Results show that flexing is not necessarily beneficial for the performance of the airfoils. However, with the correct parameters, efficiency is as high as 0.76 by placing the flexing centre at the trailing edge. The average thrust coefficient is more than twice as high, from 1.63 to 3.57 with flapping and flexing under the right conditions. Moreover, the single-sided flexing also gives an average lift coefficient as high as 4.61 for the S1020 airfoil. The shape of the airfoil does alter the effect of flexing too. Deviating the flexing phase angle away from 90° does not give a significant improvement to the airfoil’s performance. These results greatly enhance the design of a better performing ornithopter wing.     

Time resolved PIV analysis of flow over a NACA 0015 airfoil with Gurney flap

A NACA 0015 airfoil with and without a Gurney flap was studied in a wind tunnel with Re _c = 2.0 × 10⁵ in order to examine the evolving flow structure of the wake through time-resolved PIV and to correlate this structure with time-averaged measurements of the lift coefficient. The Gurney flap, a tab of small length (1–4% of the airfoil chord) that protrudes perpendicular to the chord at the trailing edge, yields a significant and relatively constant lift increment through the linear range of the C _L versus α curve. Two distinct vortex shedding modes were found to exist and interact in the wake downstream of flapped airfoils. The dominant mode resembles a Kàrmàn vortex street shedding behind an asymmetric bluff body. The second mode, which was caused by the intermittent shedding of fluid recirculating in the cavity upstream of the flap, becomes more coherent with increasing angle of attack. For a 4% Gurney flap at α = 8°, the first and second modes corresponded with Strouhal numbers based on flap height of 0.18 and 0.13. Comparison of flow around ‘filled’ and ‘open’ flap configurations suggested that the second shedding mode was responsible for a significant portion of the overall lift increment.     

Experimental study of pitching and plunging airfoils at low Reynolds numbers

Measurements of the unsteady flow structure and force time history of pitching and plunging SD7003 and flat plate airfoils at low Reynolds numbers are presented. The airfoils were pitched and plunged in the effective angle of attack range of 2.4°–13.6° (shallow-stall kinematics) and ?6° to 22° (deep-stall kinematics). The shallow-stall kinematics results for the SD7003 airfoil show attached flow and laminar-to-turbulent transition at low effective angle of attack during the down stroke motion, while the flat plate model exhibits leading edge separation. Strong Re-number effects were found for the SD7003 airfoil which produced approximately 25 % increase in the peak lift coefficient at Re = 10,000 compared to higher Re flows. The flat plate airfoil showed reduced Re effects due to leading edge separation at the sharper leading edge, and the measured peak lift coefficient was higher than that predicted by unsteady potential flow theory. The deep-stall kinematics resulted in leading edge separation that led to formation of a large leading edge vortex (LEV) and a small trailing edge vortex (TEV) for both airfoils. The measured peak lift coefficient was significantly higher (~50 %) than that for the shallow-stall kinematics. The effect of airfoil shape on lift force was greater than the Re effect. Turbulence statistics were measured as a function of phase using ensemble averages. The results show anisotropic turbulence for the LEV and isotropic turbulence for the TEV. Comparison of unsteady potential flow theory with the experimental data showed better agreement by using the quasi-steady approximation, or setting C(k) = 1 in Theodorsen theory, for leading edge–separated flows.     

钝后缘风力机翼型的环量控制研究

钝后缘风力机翼型具有结构强度高、对表面污染不敏感等优点,但其较大的阻力系数使得翼型的整体气动特性不够理想. 利用环量控制方法对钝后缘风力机翼型进行了流动控制,以改善钝后缘风力机翼型的气动特性,减弱尾迹区脱体涡强度. 通过对钝后缘风力机翼型环量控制方法进行相关的数值模拟,对比研究了环量控制方法的增升减阻效果, 研究了环量控制下翼型升阻力特性随射流动量系数的变化规律,并对不同射流动量系数下环量控制方法的气动品质因子和控制效率进行了分析. 研究结果表明:环量控制方法能够大幅提升钝后缘风力机翼型的升力系数,同时有效地降低翼型的阻力系数; 翼型的升力系数随射流动量系数的增大而增大,表现出很明显的分离控制阶段和超环量控制阶段的变化规律; 射流能耗的功率系数随射流动量系数的增大而增大,且增长速率逐渐增大;实施环量控制方法后叶片的输出功率同样随射流动量系数增大而增大,但增长速率逐渐降低. 总体来说,环量控制方法可以有效地改善钝后缘风力机翼型的气动特性以及功率输出特性,在大型风力机流动控制中具有很好的应用前景.      

High-fidelity simulations of moving and flexible airfoils at low Reynolds numbers

The present paper highlights results derived from the application of a high-fidelity simulation technique to the analysis of low-Reynolds-number transitional flows over moving and flexible canonical configurations motivated by small natural and man-made flyers. This effort addresses three separate fluid dynamic phenomena relevant to small fliers, including: laminar separation and transition over a stationary airfoil, transition effects on the dynamic stall vortex generated by a plunging airfoil, and the effect of flexibility on the flow structure above a membrane airfoil. The specific cases were also selected to permit comparison with available experimental measurements. First, the process of transition on a stationary SD7003 airfoil section over a range of Reynolds numbers and angles of attack is considered. Prior to stall, the flow exhibits a separated shear layer which rolls up into spanwise vortices. These vortices subsequently undergo spanwise instabilities, and ultimately breakdown into fine-scale turbulent structures as the boundary layer reattaches to the airfoil surface. In a time-averaged sense, the flow displays a closed laminar separation bubble which moves upstream and contracts in size with increasing angle of attack for a fixed Reynolds number. For a fixed angle of attack, as the Reynolds number decreases, the laminar separation bubble grows in vertical extent producing a significant increase in drag. For the lowest Reynolds number considered (Re _c  = 10⁴), transition does not occur over the airfoil at moderate angles of attack prior to stall. Next, the impact of a prescribed high-frequency small-amplitude plunging motion on the transitional flow over the SD7003 airfoil is investigated. The motion-induced high angle of attack results in unsteady separation in the leading edge and in the formation of dynamic-stall-like vortices which convect downstream close to the airfoil. At the lowest value of Reynolds number (Re _c  = 10⁴), transition effects are observed to be minor and the dynamic stall vortex system remains fairly coherent. For Re _c  = 4 × 10⁴, the dynamic-stall vortex system is laminar at is inception, however shortly afterwards, it experiences an abrupt breakdown associated with the onset of spanwise instability effects. The computed phased-averaged structures for both values of Reynolds number are found to be in good agreement with the experimental data. Finally, the effect of structural compliance on the unsteady flow past a membrane airfoil is investigated. The membrane deformation results in mean camber and large fluctuations which improve aerodynamic performance. Larger values of lift and a delay in stall are achieved relative to a rigid airfoil configuration. For Re _c = 4.85 × 10⁴, it is shown that correct prediction of the transitional process is critical to capturing the proper membrane structural response.     

On the Design of Lifting Airfoils with High Critical Mach Number Using Full Potential Theory

 We wish to construct airfoils that have the highest free-stream Mach number for a given set of geometric constraints for which the flow is nowhere supersonic. Nonlifting airfoils that maximize the critical Mach number for a given cross-sectional area are known to possess long sonic segments at their critical speed. To construct lifting airfoils, we proceed under the conjecture that an airfoil with a high value of has the longest possible arc length of sonic velocity over its upper and lower surface. In Kropinski et al. (1995) the lifting problem was tackled in transonic small-disturbance theory. In this paper we numerically construct lifting airfoils with high using the full potential theory and we show that these airfoils have significantly higher than some standard airfoils. We also construct airfoils with higher values of the lift coefficient, by relaxing the speed constraint on the lower surface of the airfoil to have a value less than sonic. Received 13 May 1996 accepted 12 September 1996)     

An experimental study of a bio-inspired corrugated airfoil for micro air vehicle applications

An experimental study was conducted to investigate the aerodynamic characteristics of a bio-inspired corrugated airfoil compared with a smooth-surfaced airfoil and a flat plate at the chord Reynolds number of Re _C  = 58,000–125,000 to explore the potential applications of such bio-inspired corrugated airfoils for micro air vehicle designs. In addition to measuring the aerodynamic lift and drag forces acting on the tested airfoils, a digital particle image velocimetry system was used to conduct detailed flowfield measurements to quantify the transient behavior of vortex and turbulent flow structures around the airfoils. The measurement result revealed clearly that the corrugated airfoil has better performance over the smooth-surfaced airfoil and the flat plate in providing higher lift and preventing large-scale flow separation and airfoil stall at low Reynolds numbers (Re _C  < 100,000). While aerodynamic performance of the smooth-surfaced airfoil and the flat plate would vary considerably with the changing of the chord Reynolds numbers, the aerodynamic performance of the corrugated airfoil was found to be almost insensitive to the Reynolds numbers. The detailed flow field measurements were correlated with the aerodynamic force measurement data to elucidate underlying physics to improve our understanding about how and why the corrugation feature found in dragonfly wings holds aerodynamic advantages for low Reynolds number flight applications.     

Proper Orthogonal Decomposition of Flexible Clap and Fling Elastic Motions via High-Speed Deformation Measurements

Many complex unsteady mechanisms are thought to facilitate the high efficiency and agility commonly observed in small biological flyers. One of these, the flexible clap and fling maneuver, has not been extensively studied; an experimental characterization is the focus of this work. The clap–fling mechanism is approximated with a single flexible membrane flapping wing, replacing the symmetry plane between two wings with a splitter plate simulating the pair wing. This produces a complex vibro-impact aeroelastic problem, the deformation resulting from which is measured with a high-speed visual image correlation system. A low-dimensional representation of the ensuing large data set is obtained with proper orthogonal decomposition. The POD modes, and the relative importance of each, can help elucidate crucial mechanisms and relationships within the flapping system, and are computed for various membrane wing structures and flapping frequencies, with or without the presence of the splitter plate.     

低雷诺数下柔性翼型气动性能分析

基于流固耦合方法对吸力面5%至95%弦长处为三段柔性结构的NACA0012翼型绕流进行了数值模拟,研究了不同弹性模量下柔性翼型的气动性能和结构响应.结果表明:在大攻角下,翼面变形影响着翼型表面的非定常流场,起到延缓失速和提高升力的作用;失速后柔性翼的升力系数下降得较为缓慢,且柔性越大,升力系数下降得越平缓;适当减小弹性模量能够提高翼型的气动性能,然而弹性模量过小反而不利于翼型气动性能的提升,并且翼面会产生大幅度的振动.     

A rotating elliptic airfoil in fluid at rest and in a parallel freestream

This paper reports results of DPIV measurements on a two-dimensional elliptic airfoil rotating about its own axis of symmetry in a fluid at rest and in a parallel freestream. In the former case, we examined three rotating speeds (Re _c,Ω = 400, 1,000 and 2,000), and in the later case, four rotating speeds (Ro _c,Ω = 2.4, 1.2, 0.6 and 0.4), together with two freestream velocities (Re _c,u  = 200 and 1,000) and two starting configurations of the airfoil (i.e., chord parallel to (α ₀ = 0°) or normal (α ₀ = 90°) to the freestream). Results show that a rotating airfoil in a stationary fluid produces two distinct types of vortex structures depending on the Reynolds number. The first type occurs at the lowest Reynolds number (Re _c,Ω = 400), where vortices shed from the two edges or tips of the airfoil dissipated quickly, resulting in the airfoil rotating in a layer of diffused vorticity. The second type occurs at higher Reynolds numbers (i.e., Re _c,Ω = 1,000 and 2,000), where the corresponding vortices rotated together with the airfoil. Due to the vortex suction effect, the torque characteristics are likely to be heavily damped for the first type because of the rapidly subsiding vortex shedding, and more oscillatory for the second type due to persistent presence of tip vortices. In a parallel freestream, increasing the tip-speed ratio (V/U) of the airfoil (i.e., decreasing the Rossby number, Ro _c,Ω) transformed the flow topology from periodic vortex shedding at Ro _c,Ω = 2.4 to the generation of a “hovering vortex” at Ro _c,Ω = 0.6 and 0.4. The presence of the hovering vortex, which has not been reported in literature before, is likely to enhance the lift characteristics of the airfoil. Freestream Reynolds number is found to have minimal effect on the vortex formation and shedding process, although it enhances shear layer instability and produces more small-scale flow structures that affect the dynamics of the hovering vortex. Likewise, initial starting configuration of the airfoil, while affecting the flow transient during the initial phase of rotation, has insignificant effect on the overall flow topology. Unfortunately, technical constraint of our apparatus prevented us from carrying out complimentary force measurements; nevertheless, the results presented herein, which are more extensive than those computed by Lugt and Ohring (1977), will provide useful benchmark data, from which more advanced numerical calculations can be carried out to ascertain the corresponding force characteristics, particularly for those conditions with the presence of hovering vortex.     

A new direct design method for the medium thickness wind turbine airfoil

The newly developed integral function of airfoil profiles based on Trajkovski conformal transform theory could be used to optimize the profiles for the thin thickness airfoil. However, it is hard to adjust the coefficients of the integral function for the medium thickness airfoil. B-spline curve has an advantage of local adjustment, which makes it to effectively control the airfoil profiles at the trailing edge. Therefore, a new direct design method for the medium thickness wind turbine airfoil based on airfoil integral expression and B-spline curve is presented in this paper. An optimal mathematical model of an airfoil is built. Two new airfoils with similar thickness, based on the new designed method and the original integral method, are designed. According to the comparative analysis, the CQU-A25 airfoil designed based on the new method exhibits better results than that of the CQU-I25 airfoil which is designed based on the original method. It is demonstrated that the new method is feasible to design wind turbine airfoils. Meanwhile, the comparison of the aerodynamic performance for the CQU-A25 airfoil and for the DU91-W2-250 airfoil is studied. Results show that the maximum lift coefficient and the maximum lift/drag ratio of the CQU-A25 airfoil are higher than the ones of DU91-W2-250 airfoil in the same condition. This new airfoil design method would make it possible to design other airfoils with different thicknesses.     

Maneuvering Aspects and 3D Effects of Active Airfoil Flow Control

An active flow control experiment was conducted on a cropped NACA 0018 airfoil to study 3D effects and maneuverability aspects made possible by a segmented actuation system installed in the airfoil. The 14 piezo-fluidic actuators were installed at the corner of the cropped region, inclined at 30° to the local surface, facing downstream. Operating all actuators at unison significantly increased lift and generated a pitch-down moment. Operating all actuators at the same magnitude but varying the phase along the span generated larger lift-increment, with respect to the uniform phase excitation. Significant rolling moment can be generated when only half-span of the wing is actuated. The latter effect, as indicated by the 3D pressure distribution, persists to the leading edge even though the excitation was introduced close to the trailing edge. When a pair, out of the possible fourteen actuators is not operating, very little of the control authority is lost. This is an important finding when issues like fault tolerance and robustness of fluidic-piezo actuators are considered.     

The ultra-low Reynolds number airfoil wake

Lift force and the near wake of an NACA 0012 airfoil were measured over the angle (α) of attack of 0°–90° and the chord Reynolds number (Re _c ), 5.3 × 10³–5.1 × 10⁴, with a view to understand thoroughly the near wake of the airfoil at low- to ultra-low Re _c . While the lift force is measured using a load cell, the detailed flow structure is captured using laser-Doppler anemometry, particle image velocimetry, and laser-induced fluorescence flow visualization. It has been found that the stall of an airfoil, characterized by a drop in the lift force, occurs at Re _c  ≥ 1.05 × 10⁴ but is absent at Re _c  = 5.3 × 10³. The observation is connected to the presence of the separation bubble at high Re _c but absence of the bubble at ultra-low Re _c , as evidenced in our wake measurements. The near-wake characteristics are examined and discussed in detail, including the vortex formation length, wake width, spanwise vorticity, wake bubble size, wavelength of K–H vortices, Strouhal numbers, and their dependence on α and Re _c .     

Analysis of non-symmetrical flapping airfoils

Simulations have been done to assess the lift, thrust and propulsive efficiency of different types of non-symmetrical airfoils under different flapping configurations. The variables involved are reduced frequency, Strouhal number, pitch amplitude and phase angle. In order to analyze the variables more efficiently, the design of experiments using the response surface methodology is applied. Results show that both the variables and shape of the airfoil have a profound effect on the lift, thrust, and efficiency. By using non- symmetrical airfoils, average lift coefficient as high as 2.23 can be obtained. The average thrust coefficient and efficiency also reach high values of 2.53 and 0.61, respectively. The lift production is highly dependent on the airfoil＇s shape while thrust production is influenced more heavily by the variables. Efficiency falls somewhere in between. Two-factor interac- tions are found to exist among the variables. This shows that it is not sufficient to analyze each variable individually. Vorticity diagrams are analyzed to explain the results obtained. Overall, the S1020 airfoil is able to provide relatively good efficiency and at the same time generate high thrust and lift force. These results aid in the design of a better ornithopter＇s wing.     

Reynolds number, thickness and camber effects on flapping airfoil propulsion

The effect of varying airfoil thickness and camber on plunging and combined pitching and plunging airfoil propulsion at Reynolds number Re=200, 2000, 20 000 and 2×10⁶ was studied by numerical simulations for fully laminar and fully turbulent flow regimes. The thickness study was performed on 2-D NACA symmetric airfoils with 6-50% thick sections undergoing pure plunging motion at reduced frequency k=2 and amplitudes h=0.25 and 0.5, and for combined pitching and plunging motion at k=2, h=0.5, phase ?=90°, pitch angle θ_o=15° and 30° and the pitch axis was located at 1/3 of chord from leading edge. At Re=200 for motions where positive thrust is generated, thin airfoils outperform thick airfoils. At higher Re significant gains could be achieved both in thrust generation and propulsive efficiency by using a thicker airfoil section for plunging and combined motion with low pitch amplitude. The camber study was performed on 2-D NACA airfoils with varying camber locations undergoing pure plunging motion at k=2, h=0.5 and Re=20 000. Little variation in thrust performance was found with camber. The underlying physics behind the alteration in propulsive performance between low and high Reynolds numbers has been explored by comparing viscous Navier-Stokes and inviscid panel method results. The role of leading edge vortices was found to be key to the observed performance variation.     

Sound generation and flow interaction of vortices with an airfoil and a flat plate in transonic flow

The mechanisms of sound generation and the kind of interaction of vortices with airfoils in an airflow are investigated. Experiments have been performed in stationary flow with vortices of a Kármán vortex street and in a shock tube flow with a starting vortex of a lifting airfoil. Depending on the dimensions of vortices and airfoils, their distance, and the flow Mach numbers, different kinds and amplitudes of upstream propagating steep sound waves occur.