形状记忆合金拟弹性行为的热力学描述

形状记忆合金是由马氏体和奥氏体组成并动态变化的两相材料 ,其拟弹性行为实质上是两相各自行为的动态组合。本文提出了形状记忆合金拟弹性行为的一种热力学描述。根据实验现象假设在感兴趣的温度和变形范围内 ,奥氏体相具有线弹性特性而马氏体相具有弹塑性特性 ,结合 Tanaka的相变描述 ,给出了小变形、初始各向同性和塑性不可压缩条件下形状记忆合金的三维本构方程。对不同温度下形状记忆合金材料的特性进行了描述 ,较好地预言了单调及循环加载下的响应和正、反相变行为及其温度影响 ,动态相变过程对应力响应的影响 ,高温相下的强度增加等。     

NiTi形状记忆合金动态压缩力学行为的实验研究

采用材料试验机和SHPB实验技术,对在不同初始温度(298～873K)和应变率(5×10-4、～2.3×103s-1)下的NiTi形状记忆合金的压缩力学行为进行了实验研究。结果表明:马氏体状态下的NiTi合金的力学行为对应变率的变化敏感,位错屈服段的硬化模量、相屈服段的硬化模量及马氏体重取向前的弹性模量对应变率的变化不敏感,而位错塑性变形前的弹性模量随应变率的提高迅速增大;奥氏体状态下的NiTi合金随着实验温度升高,无论是应力诱发马氏体相变应力还是奥氏体相屈服应力都逐渐下降,材料表现出温度软化效应。从超弹性温度范围内的卸载曲线中观察到了应力诱发马氏体到奥氏体的逆转变。     

形状记忆合金单晶细观本构关系的一种相变动力学模型及算法

形状记忆合金是由马氏体相和奥氏体相组成的非均质材料,热力载荷及相变不可避免地在材料中引起残余微应力场,它与外界驱动力的叠加可能导致低应力水平下发生马氏体相变或逆相变.论文假设马氏体相变及逆相变的驱动力是马氏体体积分数的连续函数,发展了形状记忆合金伪弹性的本构描述及相应的数值分析方法.分析表明,所发展的方法与理想相变模型间的误差远小于已有工作中引入的容许误差.对形状记忆合金单晶伪弹性响应的计算结果与试验结果或已有模型计算结果的比较表明所发展的方法具有较高的精度.此外,所发展的方法具有明晰的物理背景,且无需对每个变体的相变发生与否及其方向进行判断,简化了计算过程,提高了计算效率和收敛性.     

应力作用下NiTi形状记忆合金微结构演化的相场模拟及其本征应变率敏感性

基于Ginzburg-Landau动力学控制方程建立了NiTi形状记忆合金非等温相场模型,实现了对NiTi合金内应力诱导马氏体相变的数值模拟。同时将晶界能密度引入系统局部自由能密度,从而考虑多晶系统中晶界的重要作用。数值计算了单晶和多晶NiTi形状记忆合金在单轴机械载荷作用下微结构的动态演化过程和宏观力学行为,并重点研究了晶粒尺寸为60 nm的NiTi纳米多晶在低应变率下（0.000 5～15 s-1）力学行为的本征应变率敏感性。研究结果表明,单晶NiTi合金系统高温拉伸-卸载过程中马氏体相变均匀发生,未形成奥氏体-马氏体界面。而纳米多晶系统在加载阶段出现了马氏体带的形成-扩展现象,在卸载阶段出现了马氏体带的收缩-消失现象。相同外载作用过程中,NiTi单晶系统的宏观应力-应变曲线具有更大的滞回环面积,拥有更优的超弹性变形能力。计算结果显示,在中低应变率下纳米晶NiTi形状记忆合金应力-应变关系表现出较明显的应变率相关性,应变率升高导致材料相变应力提升。这一应变率相关性主要源于相场模型中外加载荷速率与马氏体空间演化速度的相互竞争关系。     

马氏体相变微结构演化过程的模拟与分析

实验中观察到形状记忆合金在应力诱发马氏体相变过程中,出现多界面的微结构,马氏体相会逐渐长大变粗,同时会出现由马氏体形核造成的应力突然降低.用多阱的弹性能函数来刻画此相变与微结构演化过程,发现相变时会出现多界面的微结构且伴随着马氏体相的形核至奥氏体相的消失过程,出现了界面数先增后减的变化,同时应力会出现跳跃而不连续.相对应的动力学模型的有限差分的计算结果同样显示形核时出现了多界面的微结构并伴随着应力的大幅振荡,随着载荷的增加界面位置随之移动,使得马氏体相区域逐渐长大.理论分析与数值模拟的结果较好地刻画了实验中观察到的马氏体相变过程中的形核,产生多界面,再到马氏体逐渐长大这一微结构的演化过程.     

Cu-Al-Be形状记忆合金湿磨粒磨损性能研究

采用销-盘式二体磨损试验研究了CuAlBe形状记忆合金的湿磨粒磨损行为．结果表明，CuAlBe形状记忆合金的磨损性能不完全取决于材料硬度，具有热弹性马氏体组织的A合金的抗磨性优于高硬度B合金．在湿磨粒磨损条件下，A合金具有β′1 β双相组织，在磨粒的交变应力作用下，由于β相应力诱发马氏体相变、β′1相马氏体变体择优取向并产生形状记忆效应，使应变弹性回复，并钝化裂纹尖端，使得A合金具有优良的抗磨粒磨损性能．     

热弹性马氏体相变连续介质热力学研究

介绍形状记忆合金热弹性马氏体相变连续介质热力学研究方法和最新进展, 着重分析了在推广的非线性弹性力学的框架下, 应用变分方法研究热弹性马氏体相变的理论和方法、存在的问题及发展趋势. 首先介绍如何计算马氏体相变24种变体的变形梯度, 然后拓展非线性弹性力学, 引入描述相变的多阱非凸弹性势能, 进而讨论了界面能和非局部能对相变微结构和相变过程的影响的相关研究理论方法和进展.      

纳米多晶NiTi形状记忆合金超弹性的晶粒取向依赖性相场研究

本文基于Ginzburg-Landau理论,建立了一个反映纳米多晶NiTi形状记忆合金取向依赖性的二维多晶相场模型,研究了晶粒取向对其超弹性性能的影响。结果表明,纳米多晶NiTi形状记忆合金的超弹性行为依赖于晶粒取向分布,即：多晶模型中在所研究的参数变化范围内,晶粒取向分布范围越广、晶粒间取向差越大（无明显织构）,超弹性性能越差;而晶粒取向分布范围越窄、晶粒间取向差越小（织构越强）,超弹性性能越好。该晶粒取向依赖性可解释为：由于晶粒取向的不同,马氏体相变过程中相邻晶粒间的变形不匹配程度不同,因此,多晶模型中在所研究的参数变化范围内,晶粒间取向差异越大,晶界处的变形失配越严重,由此而产生的局部内应力将阻碍其附近马氏体相变的扩展,进而导致纳米多晶NiTi形状记忆合金超弹性性能下降。     

超弹性镍钛形状记忆合金单轴相变棘轮行为的宏观唯象本构模型

超弹性镍钛形状记忆合金因其良好的力学性能以及独特的超弹性和形状记忆效应已广泛应用于土木工程、航空航天和生物医疗等多个领域,在实际服役环境中超弹性镍钛合金元件不可避免地会承受不同应力水平的循环载荷作用,亟待建立描述相变棘轮行为(即峰值应变和谷值应变随着正相变和逆相变循环的进行不断累积)的循环本构模型.为此,基于已有的超弹性镍钛形状记忆合金在不同峰值应力下的单轴相变棘轮行为实验研究结果,在广义黏塑性框架下,对Graesser等提出的通过背应力非线性演化方程反映超弹性镍钛形状记忆合金超弹性行为的一维宏观唯像本构模型进行了拓展,考虑了正相变和逆相变过程中特征变量的差异及其随循环的演化,以非弹性应变的累积量为内变量引入了正相变开始应力、逆相变开始应力、相变应变和残余应变的演化方程,同时通过峰值应力与正相变完成应力的比值来确定演化方程中的相关系数,建立了描述超弹性镍钛合金单轴相变棘轮行为的本构模型.将模拟结果与对应的实验结果进行对比发现,建立的宏观唯像本构模型能够合理地描述超弹性镍钛形状记忆合金的单轴相变棘轮行为及其峰值应力依赖性,模型的预测结果和实验结果吻合得很好.     

NiTi形状记忆合金裂纹尖端热力耦合行为研究

本文对NiTi形状记忆合金I型裂纹尖端热力耦合行为进行了数值仿真分析和实验验证。建立了包含相变和热力耦合的本构模型,通过有限元计算得到了裂纹尖端附近的纵向应变、马氏体体积分数和温度场分布,依据马氏体相变情况对裂纹尖端有效应力强度因子进行了修正,揭示了加载速率对形状记忆合金裂纹尖端有效应力强度影子的影响规律。参数研究表明,随着加载频率的增加,裂纹尖端附近温度逐渐升高,马氏体相变区域逐渐缩小,有效应力强度因子呈下降趋势,形状记忆合金表现出增韧效应,有助于减缓裂纹扩展。本研究结果对于揭示热力耦合作用下超弹性形状记忆合金疲劳裂纹扩展规律具有重要参考意义。     

A 3-D constitutive model for shape memory alloys incorporating pseudoelasticity and detwinning of self-accommodated martensite

A 3-D constitutive model for polycrystalline shape memory alloys (SMAs), based on a modified phase transformation diagram, is presented. The model takes into account both direct conversion of austenite into detwinned martensite as well as the detwinning of self-accommodated martensite. This model is suitable for performing numerical simulations on SMA materials undergoing complex thermomechanical loading paths in stress–temperature space. The model is based on thermodynamic potentials and utilizes three internal variables to predict the phase transformation and detwinning of martensite in polycrystalline SMAs. Complementing the theoretical developments, experimental data are presented showing that the phase transformation temperatures for the self-accommodated martensite to austenite and detwinned martensite to austenite transformations are different. Determination of some of the SMA material parameters from such experimental data is also discussed. The paper concludes with several numerical examples of boundary value problems with complex thermomechanical loading paths which demonstrate the capabilities of the model.     

A CONSTITUTIVE MODEL FOR TRANSFORMATION, REORIENTATION AND PLASTIC DEFORMATION OF SHAPE MEMORY ALLOYS

A constitutive model is developed for the transformation, reorientation and plastic deformation of shape memory alloys (SMAs). It is based on the concept that an SMA is a mixture composed of austenite and martensite, the volume fraction of each phase is transformable with the change of applied thermal-mechanical loading, and the constitutive behavior of the SMA is the combination of the individual behavior of its two phases. The deformation of the martensite is separated into elastic, thermal, reorientation and plastic parts, and that of the austenite is separated into elastic, thermal and plastic parts. Making use of the Tanaka’s transformation rule modified by taking into account the effect of plastic deformation, the constitutive model of the SMA is obtained. The ferroelasticity, pseudoelasticity and shape memory effect of SMA Au-47.5 at.%Cd, and the pseudoelasticity and shape memory effect as well as plastic deformation and its effect of an NiTi SMA, are analyzed and compared with experimental results.     

A three-dimensional constitutive model for shape memory alloys

Shape memory alloys (SMAs) are materials that, among other characteristics, have the ability to present high deformation levels when subjected to mechanical loading, returning to their original form after a temperature change. Literature presents numerous constitutive models that describe the phenomenological features of the thermomechanical behavior of SMAs. The present paper introduces a novel three-dimensional constitutive model that describes the martensitic phase transformations within the scope of standard generalized materials. The model is capable of describing the main features of the thermomechanical behavior of SMAs by considering four macroscopic phases associated with austenitic phase and three variants of martensite. A numerical procedure is proposed to deal with the nonlinearities of the model. Numerical simulations are carried out dealing with uniaxial and multiaxial single-point tests showing the capability of the introduced model to describe the general behavior of SMAs. Specifically, uniaxial tests show pseudoelasticity, shape memory effect, phase transformation due to temperature change and internal subloops due to incomplete phase transformations. Concerning multiaxial tests, the pure shear stress and hydrostatic tests are discussed showing qualitatively coherent results. Moreover, other tensile–shear tests are conducted modeling the general three-dimensional behavior of SMAs. It is shown that the multiaxial results are qualitative coherent with the related data presented in the literature.     

A NEW MODEL OF SHAPE MEMORY ALLOYS

A new constitutive model of shape memory alloys ( SMAs) based on Tanaka ' s martensite fraction exponential expression is produced. This new model can present recoverable shape memory strain during different phase transformation, and reflect the action of martensite reorientation . Also it can overcome the defect of Tanaka ' s Model when the SMAs ' microstructure is fully martensite . The model is very simple and suitable for using , and the correct behavior of the model is proved by test.     

A macroscopic multi-mechanism based constitutive model for the thermo-mechanical cyclic degeneration of shape memory effect of NiTi shape memory alloy

A macroscopic based multi-mechanism constitutive model is constructed in the framework of irreversible thermodynamics to describe the degeneration of shape memory effect occurring in the thermo-mechanical cyclic deformation of NiTi shape memory alloys(SMAs). Three phases,austenite A, twinned martensite Mtand detwinned martensite M~d, as well as the phase transitions occurring between each pair of phases( A → M~t, M~t→ A, A → M~d,M~d→ A, and M~t→ M~d) are considered in the proposed model. Meanwhile, two kinds of inelastic deformation mechanisms, martensite transformation-induced plasticity and reorientation-induced plasticity, are used to explain the degeneration of shape memory effects of NiTi SMAs. The evolution equations of internal variables are proposed by attributing the degeneration of shape memory effect to the interaction between the three phases(A, M~t, and M~d) and plastic deformation. Finally, the capability of the proposed model is verified by comparing the predictions with the experimental results of NiTi SMAs. It is shown that the degeneration of shape memory effect and its dependence on the loading level can be reasonably described by the proposed model.     

Coupling between martensitic phase transformations and plasticity: A microstructure-based finite element model

A microstructural finite element (MFE) model is developed to capture the interaction between martensitic transformations and plasticity in NiTi shape memory alloys (SMAs). The interaction is modeled through the grain-to-grain redistribution of stress caused by both plasticity and phase transformation, so that each mechanism affects the driving force of the other. A unique feature is that both processes are modeled at a crystallographic level and are allowed to operate simultaneously. The model is calibrated to pseudoelastic data for select single crystals of Ti–50.9at.%Ni. For polycrystals, plasticity is predicted to enhance the overall martensite volume fraction at a given applied stress. Upon unloading, residual stress can induce remnant (retained) martensite. For thermal cycling under load bias, plasticity is observed to limit the net transformation strain/cycle and increase the hysteretic width. Deformation processing, via plastic pre-straining at elevated temperature, is shown to dramatically alter subsequent pseudoelastic response, as well as induce two-way shape memory behavior during no-load thermal cycling. Overall, the model is suitable at smaller imposed strains, where martensite detwinning is not expected to dominate.     

Phase proportioning in CuAlBe shape memory alloys during thermomechanical loadings using electric resistance variation

The microstructure of shape memory alloys changes with the thermomechanical history of the material. During thermomechanical loading, austenite, thermally-induced martensite or stress-induced martensite can be simultaneously present in the material. In applications integrating SMA parts, utilization conditions seriously affect the microstructure and can generate macroscopic strain or stress. Consequently, during thermomechanical loadings, it is important to be able to proportion the different phases and consequently to understand the kinetic transformation. This is very useful in the development of constitutive equations. This study shows, by a series of tests, that the proposed experimental method, based on the measurement of the variation of electric resistance of CuAlBe wires, permits to determine the volume fraction of the different phases present in the material (i.e., austenite, stress-induced martensite and thermally-induced martensite). The proposed method is applied to the most common thermomechanical behavior met in engineering applications of shape memory alloys: pseudoelasticity, pseudoplasticity, recovery-stress and stress-assisted two-way shape memory effect. The proportioning method based on a mixture law integrating the resistivity of pure phases present in the SMA is first performed on different two-phase mixture cases and then applied to a three phase mixture case.