Corrosion prevention of passivated iron in 0.1 M NaCl by coverage with an ultrathin polymer coating and healing treatment in 0.1 M NaNO3

An ultrathin, ordered and two-dimensional polymer coating was prepared on a passivated iron electrode by modification of 16-hydroxyhexadecanoate ion HO(CH₂)₁₅CO₂⁻ self-assembled monolayer with 1,2-bis(triethoxysilyl)ethane (C₂H₅O)₃Si(CH₂)₂Si(OC₂H₅)₃ and octadecyltriethoxysilane C₁₈H₃₇Si(OC₂H₅)₃. Subsequently, the electrode was healed in 0.1 M NaNO₃. Protection of passivated iron against passive film breakdown and corrosion of iron was examined by monitoring of the open-circuit potential and repeated polarization measurements of the polymer-coated and healed electrode in an aerated 0.1 M NaCl solution during immersion for many hours. Localized corrosion was markedly prevented by coverage with the polymer coating and the healing treatment in 0.1 M NaNO₃. Prominent protection of iron from corrosion in 0.1 M NaCl was observed before the breakdown occurred. The electrode surface covered with the healed passive film and polymer coating was analyzed by contact angle measurement, X-ray photoelectron spectroscopy and electron-probe microanalysis.     

Mechanical relaxations of a (Zr77.5Ti22.5)55(Ni48Cu52)21.25Be23.75 amorphous alloy studied using dynamic mechanical analysis

The dynamic mechanical properties of a (Zr_77.5Ti_22.5)₅₅(Ni₄₈Cu₅₂)_21.25Be_23.75 amorphous alloy were investigated by frequency-dependent elastic moduli and isothermal multi-frequency measurements. The frequency-dependent loss modulus showed a relaxation behavior resulting from a glass transition, and the variation of the peak frequency was related to the Arrhenius equation. Isothermal multi-frequency measurement data were used to construct the master curves of the elastic moduli and tan δ by applying the time-temperature superposition principle. The temperature dependence of the shift factor was found to follow the Arrhenius relationship, and the activation energies for the low temperature relaxation and glass transition were approximately 156.6kJ/mol and 554kJ/mol, respectively. The glass transition temperature (T _g) was manifested by the crossover region of the shift factor dependence, and from the relationship between the shift factors and the temperature aboveT _g), the fragility index of this alloy was estimated.     

Corrosion behaviour of dc magnetron sputtered Fe1−xMgx alloy films in 3 wt% NaCl solution

Fe_1−xMg_x alloy films (with x ? 43.4 at.% Mg) were deposited by dc magnetron sputtering onto glass slide substrates. The objective of this study was to characterise the corrosion properties of these alloys in saline solution for application as new friendly environmentally sacrificial coatings in the protection of steel structures. The morphological and structural properties of the alloys were systematically studied prior to electrochemical experiments, and then the degraded surfaces were analysed to determine the composition and nature of corrosion products. Alloys with <25  at.% Mg were single-phase body-centred cubic (bcc) with enlarged lattice parameters, whereas for magnesium contents above 25 at.%, amorphisation occurred. The reactivity of the alloys in saline solution is strongly dependent on the Mg content and the alloy structure. The incorporation of magnesium leads to an open circuit potential shift of the alloy towards more negative values, that confers an attractive interest of these alloys as sacrificial coatings. A transition in corrosion activity is observed at 25 at.% Mg from which the reactivity decreases with the magnesium content increase. The evolution of the alloy corrosion behaviour is discussed in terms of structural and corrosion products evolution versus magnesium content.     

Oxidation of a quaternary three-phase Cu-20Ni-20Cr-5Fe alloy at 700-900 °C in 1 atm of pure O2

The oxidation of a quaternary Cu-Ni-Cr-Fe alloy containing approximately 20 at.% Ni, 20 at.% Cr and 5 at.% Fe, balance Cu (Cu-20Ni-20Cr-5Fe), was studied at 700-900 °C in 1 atm of pure oxygen. The alloy is composed of a mixture of three phases, where the lightest α phase with the largest Cu content forms the matrix, while the other two, much richer in Cr, form a dispersion of isolated particles. At variance with the ternary three-phase Cu-20Ni-20Cr alloy examined previously, which was unable to form protective chromia scales over the alloy surface even after an extended period of oxidation, the present alloy formed complex external scales containing mixtures of the oxides of the various components plus a deep internal region containing a mixture of alloy and oxide phases. With time, a very irregular and thin but essentially continuous chromia layer formed at the bottom of the mixed internal oxidation region, producing a gradual decrease of the oxidation rate. Thus, the addition of 5 at.% Fe to Cu-20Ni-20Cr alloy is able to decrease the critical Cr content required to form the most stable oxide and promotes the formation of a continuous chromia scale under a lower Cr content in spite of the simultaneous presence of three different phases.     

Corrosion behavior of Cr/Cu-coated Mg alloy (AZ91D) in 0.1 M H2SO4 with different concentrations of NaCl

An electroplating process was proposed for obtaining a protective Cr/Cu deposit on the two-phase Mg alloy AZ91D. The corrosion behavior of Cu-covered and Cr/Cu-covered AZ91D specimens was studied electrochemically in 0.1 M H₂SO₄ with different NaCl concentrations. Experimental results showed that the corrosion resistance of an AZ91D specimen improved significantly after Cr/Cu electrodeposition. The corrosion resistance of Cr/Cu-covered AZ91D decreased with increasing NaCl concentration in 0.1 M H₂SO₄ solution. After immersion in a 0.1 M H₂SO₄ with a NaCl-content above 3.5 wt.%, the surface of Cr/Cu-covered AZ91D suffered a few blisters. Cracks through the Cr deposit provided active pathways for corrosion of the Cu and the AZ91D substrate. Formation of blisters on the Cr/Cu-covered AZ91D surface was confirmed based on the results of an open-circuit potential test, which detected an obvious potential drop from noble to active potentials.     

Structure and thermal behavior of multicomponent Fe68−xNixZr15Nb5B12 (x = 5, 10, 15, 20) alloys

Multicomponent Fe_68−xNi_xZr₁₅Nb₅B₁₂ (x = 5, 10, 15, 20) alloy powders milled for 60 h were prepared by mechanical alloying (MA). The structure and crystallization behavior were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and differential thermal analysis (DTA). Ni enhances the amorphisation of alloy powders. Particle size increases with increasing Ni content. Both onset crystallization temperature T_x and the first crystallization peak temperature T_p of the four alloys shift to a higher temperature with increasing heating rate while melting temperature (T_m) is just the opposite. Fe_68−xNi_xZr₁₅Nb₅B₁₂ (x = 5, 10, 15, 20) alloys all have a large supercooled liquid region ΔT_x. The supercooled liquid region ΔT_x increases and the crystallization activation energy E decreases with increasing Ni content.