Preparation of Highly Active Pt-K/γ-Al2O3 Catalyst for o-Phenylphenol Synthesis from o-Cyclohexenyl-cyclohexanone Dehydrogenation

0.5%Pt-K/γ-Al2O3 catalysts for the synthesis of o-phenylphenol（OPP） from o-cyclohexenyl-cyclohexanone （dimer） dehydrogenation were prepared by means of a two subsequent impregnation method. The effects of catalyst preparation parameters, such as K promoters, calcination, and reduction conditions, were investigated. The results showed that the addition of K2SO4 to Pt/γ-Al2O3 catalyst notably promoted the selectivity of OPP, and its optimum content was found to be 6% in mass fraction. The higher activity was obtained when Pt/γ-Al2O3 catalyst was calcined in nitrogen atmosphere at 400--500 ℃ and then reduced at the same temperature for 3 h in hydrogen atmosphere. The conversion of the dimer and the selectivity of OPP were always above 99% and 90%, respectively, over 0.5%Pt-6% K2SO4/γ-Al2O3 catalyst during the pilot scale test of 8000 h.     

NiO在γ-Al2O3及 TiO2/γ-Al2O3载体上的表面存在状态

本文采用LRS,XRD,UV－DRS考查了γ－Al2O3上TiO2的分散容量,分散态Ti^4 离子的配位环境;NiO在经TiO2改性后的γ－Al2O3载体上的分散容量,结果表明,（1)TiO2在γ－Al2O3表面的分散容量约为0．65mmol/100m^2γ－Al2O3,当TiO2含量低于该分散容量时Ti^4 在γ－Al2O3载体表面以嵌入形式呈离子态分布,而含量离于分散容量时还有结晶态的TiO2出现,（2）NiO在TiO2/γ－Al2O3载体表面的分散容量约为1．1mmol/100m^2γ－Al2O3,比之在γ－A2O3载体表面的分散容量（1．5mmol/100m^2γ－Al2O3）要低,这是由于γ-AlO3表面上部分空位被Ti^4 离子占据,用表面相互作用的“嵌入模型”（Incorporation Model)讨论的这些结果。     

Selective oxidation of methanol on V2O5 and V2O5?MoO3 supported on montrmorillonite

Methanol oxidation on V₂O₅ and V₂O₅–MoO₃ catalysts supported on montmorillonite has been studied in the temperature range of 250–500°C. The V₂O₅–MoO₃ containing sample shows higher selectivity towards formaldehyde formation than the V₂O₅ catalyst.     

γ-Al2O3对SCR脱硝催化剂V2O5-WO3/TiO2的改性研究

采用溶胶凝胶法制备了不同γ-Al₂O₃含量的钛铝复合载体,以此为载体采用浸渍法负载V₂O₅和WO₃制备了一系列催化剂。采用X射线衍射(XRD)、比表面积测定(BET)、程序升温还原(H₂-TPR)、高分辨率透射电子显微镜(HRTEM)等表征技术对催化剂表面形态进行分析,同时在模拟氨气选择性催化还原NO(NH₃-SCR)的反应条件下,对催化剂的脱硝反应活性和SO₂抗中毒进行考察。结果发现,TiO₂和γ-Al₂O₃之间的协同作用使得V₂O₅-WO₃/TiO₂-γ-Al₂O₃催化剂的脱硝效率及活性窗口明显优于单一载体制备的催化剂,表现出了良好的热稳定性和抗SO₂毒化能力,特别是V₂O₅-WO₃/TiO₂-15% γ-Al₂O₃在310~460 ℃,NO的转化率均在80%以上,反应窗口最宽。各种表征结果表明,TiO₂-γ-Al₂O₃复合载体中γ-Al₂O₃高度分散在TiO₂上,复合载体具有较大的比表面积,同时具有较强的还原能力。     

Ammoxidation of 3- and 4-picolines over V2O5?SnO2/γ?Al2O3 catalyst

The ammoxidation of 3- and 4-picolines has been studied over V₂O₅–SnO₂/–Al₂O₃ catalysts prepared by surface impregnation technique. Best results were obtained for the generation of cyanopyridines in the temperature range 400–450°C and sub-stoichiometric value with respect to O₂. Catalysts that were calcined above 700°C showed no activity.

---

3- 4- V₂O₅–SnO₂/–Al₂O₃, . 400–450°C O₂. , 700 K, .

     

DME Synthesis From CO/H2 over Cu-Mn/?-Al2O3 Catalyst

A γ-alumina-supported copper-manganese oxide catalyst prepared by an impregnation method was used for DME synthesis from CO/H₂ (syngas). The Cu-Mn/γ-Al₂O₃ catalyst exhibits high catalytic activity in CO hydrogenation. The effect of the loading amount of Cu, the ratio of n(Cu)/n(Mn) and the reaction conditions on the activity and selectivity to dimethyl ether (DME) from CO/H₂ (syngas) were investigated. The activity was found to increase with increasing surface area of metallic copper to some extent, but it is not a linear relationship. This indicated that the catalytic activity depends on both the metallic copper area and the synergy between the copper and manganese oxide. This revised version was published online in June 2006 with corrections to the Cover Date.     

沉淀法结合超临界CO2干燥制备纳米γ-Al2O3

纳米γ-Al2O3具备多孔性、高比表面积、良好的吸附性、热稳定性和表面酸性[1,2],用作吸附剂和催化剂(及其载体),是催化剂载体领域应用最为广泛的品种[3～6].制备纳米氧化铝的方法有很多,大致可分为固相法、液相法、气相法等.     

γ-Al2O3表面原位合成Ni-Al-CO3LDHs研究

Ni-Al-CO₃LDHs/γ-Al₂O₃have been prepared using an in-situ synthesis technique. NH₃·H₂O was chosen as activation agent of Al on the γ-Al₂O₃surface as well as precipitant. Ni-Al-CO₃LDHs/γ-Al₂O₃was synthesized by controlling the reaction conditions such as temperature, concentration of Ni²⁺ and initial pH. The crystalline structure, chemical composition and porous structure were characterized by means of XRD, FT-IR, TG-DTA, ²⁷Al MAS-NMR and N₂ adsorption-desorption. The resulting sample of Ni-Al-CO₃LDHs/γ-Al₂O₃possesses higher specific area and narrower pore distribution, in which Ni-Al-CO₃LDHs are located on the surface of γ-Al₂O₃and share the same Al-O bonds with the γ-Al₂O₃lattice. Finally a possible structural model was proposed to account for the porous characters of Ni-Al-CO₃LDHs/γ-Al₂O₃.     

Hydrogenation of 2-ethylanthraquinone over Pd/Zro2-γ-Al2O3 catalyst

A ZrO₂-γ-Al₂O₃ supported Pd catalyst was prepared and characterized by XRD, XPS, H₂-TPR and TEM techniques. The catalytic activity was evaluated in the liquid-phase hydrogenation of 2-ethylanthraquinone. Comparing with Pd/γ-Al₂O₃, it showed high catalytic activity.     

CeO2/γ-Al2O3复合材料制备及其光催化性能研究

以Ce(NO₃)₃·6H₂O及Al(NO₃)₃·9H₂O为原料,NH₄HCO₃为造孔剂,以沉淀法制备了具有介孔结构的CeO₂/γ-Al₂O₃光催化材料。研究了不同NH₄∶Al及Ce∶Al摩尔比等条件下制备CeO₂/γ-Al₂O₃样品的光催化性能。结果表明,所制备CeO₂/γ-Al₂O₃复合材料具有优异的光催化性能,最佳NH₄∶Al及Ce∶Al摩尔比分别为1及0.2,该条件下制备的样品BET比表面积为94.4642 m²·g^-1,孔径为5.8565 nm,对亚甲基蓝(MB)的光催化降解率可达93.59%,动力学常数k为0.0218 m...     

CuMnCeLa-O/γ-Al2O3催化剂助燃脱硝性能研究

采用等体积浸渍法制备了Cu Mn-O/γ-Al_2O_3、Cu Mn Ce-O/γ-Al_2O_3和Cu Mn Ce La-O/γ-Al_2O_3催化剂.用XRD、BET、SEM、XPS和H_2-TPR技术对其物相和表面性质进行了表征.在连续固定床微反装置上评价了催化剂的CO+O_2和CO+NO反应性能.结果表明,催化剂样品中观测不到Cu O、Mn O_x、Ce O_2和La_2O_3的XRD晶相峰,活性组分在γ-Al_2O_3载体表面呈高度分散状态.Ce、La的引入对催化剂的比表面积、孔容和孔径分布影响不大.SEM谱图中未观测到活性组分的形貌,金属氧化物在载体表面均匀分布.Ce~(3+)!Ce~(4+)之间的可变价转换,引起Cu Mn Ce-O/γ-Al_2O_3催化剂表相Cu O中具有非完整结构的[Cu~(2+)_(1-x)Cu_x~+][O_(1-2)1_x□1_(2x)]增多,Cu~+/Cu~(2+)比例增大,表相氧空位增多,H_2-TPR还原峰温度向低温区偏移.Ce~(4+)、La~(3+)之间不平衡电荷以及共生过程中Cu-Mn-Ce-La-O之间的强相互作用,加大了Cu O和Mn O_x结构的不完整性,导致Cu Mn Ce La-O/γ-Al_2O_3催化剂样品表相产生更多的Cu~+、Mn~(2+)、Mn~(3+)和氧空位,相应的H_2-TPR还原峰温度进一步向低温区偏移.催化氧化CO和CO催化还原NO实验结果表明,在反应空速20 000 h~(-1),350℃反应温度下,Cu Mn Ce La-O/γ-Al_2O_3催化剂CO催化还原NO反应的CO转化率达到88.2%,NO转化率达到了96.1%,表现出了较好的氧化还原活性.     

Deposition of NiO onto MoO3/γ-Al2O3 extrudates by slurry impregnation method

NiO-MoO₃/γ-Al₂O₃ catalysts were prepared by the reaction of γ-Al₂O₃ extrudates with an aqueous slurry of MoO₃, followed by the reaction of the MoO₃/γ-Al₂O₃ catalyst with an aqueous slurry of NiO, Ni(OH)₂, NiCO₃·2Ni(OH)₂·xH₂O, or 2NiCO₃·3Ni(OH)₂·4H₂O and by subsequent drying. The NiO deposition was examined with electron probe microanalysis. The deposited Ni efficiently increased the activity in benzothiophene hydrodesulfurization.     

La2O3对Ni-Mo/γ-Al2O3催化剂CO和CO2甲烷化的影响

采用浸渍法制备了一系列Ni-Mo-La/γ-Al     

Effect of Fe-modified α-Al2O3 on the properties of Pd/α-Al2O3 catalysts in selective acetylene hydrogenation

The use of nanocrystalline Fe-modified α-Al₂O₃ prepared by sol–gel and solvothermal method as supports for Pd catalysts resulted in an improved catalyst performance in selective acetylene hydrogenation. Moreover, the amount of coke deposits was reduced due to lower acidity of the Fe-modified α-Al₂O₃ supports.     

Kinetics of Methane Partial Oxidation to Syngas over a LiLaNiO/γ -Al2O3 Catalyst

The kinetic behavior of partial oxidation of methane to syngas over a LiLaNiO/γ -Al₂O₃ catalyst was investigated under steady-state conditions. Under kinetic control, syngas, to a large extent, is formed via a direct partial oxidation (DPO) scheme. CO and CO₂ are formed in parallel by oxidation reaction over the catalyst. The active sites in the kinetically controlled regime are different from those in the non-kinetic regime, thus the CO selectivity in the former may not increase with temperature. This revised version was published online in June 2006 with corrections to the Cover Date.     

ESR Characterization and Activity of V_2O_5/γ-Al_2O_3 Catalysts for Dehydrogenation of Isobutane

IntroductionIsobutene is the raw material for theproduction of many important chemicals.Thedehydrogenation of isobutane to isobutene oncatalysts Cr2 O3/γ- Al2 O3and Pt/γ- Al2 O3have beenextensively studied and successfully applied inindustry[1,2 ] .The dehydrogenation of isobutane to isobuteneis an endothermic reaction and is limited by thechemical equilibrium.Coke is easy formed on thecatalyst surface and the catalyst is frequentlyregenerated in the running.The oxidativedehydrogenation …     

低温等离子体协助B2O3/γ-Al2O3 选择催化还原NO（英文）

研究了低温等离子体协助催化条件下甲烷选择性催化还原NO反应(SCR).反应气体经等离子体活化后,生成NO2,HCHO,CH3NO和CH3NO2等活性更高的中间产物.程序升温表面反应表明,这些中间产物可在等离子体后置催化装置上进一步反应,从而使NOx还原为N2.在考察的一系列催化剂(包括γ-Al2O3,Ag/γ-Al2O3,B2O3/γ-Al2O3,Ga2O3/γ-Al2O3,In2O3/γ-Al2O3等)中,B2O3/γ-Al2O3表现出最好的催化活性.当反应温度为300oC时,NOx转化率达到最高.与γ-Al2O3催化剂相比,在10wt%B2O3/γ-Al2O3催化剂上,300oC时,NOx转化为N2的转化率从33.4%提高至51.0%.催化剂的酸性对于经等离子体活化后的反应气体在催化剂上的SCR反应起到重要作用.同时,催化剂上吸附态NOx对于NOx的转化也起到一定作用.     

商业V2O5-WO3/TiO2脱硝催化剂砷中毒机理

采用浸渍法模拟商业V₂O₅-WO₃/TiO₂脱硝催化剂的砷中毒,并对不同As/V摩尔比中毒的催化剂进行脱硝实验测试,发现随着As中毒程度加深,催化剂的NO_x转化率随之降低.当测试温度为400℃时,新鲜V₂O₅-WO₃/TiO₂催化剂NO_x转化率有96.45%,而当As/V摩尔比到0.2的时候,As中毒催化剂的NO_x转化率降低至不足67%.采用XRD、BET、SEM、in situ DRIFTS和H₂-TPR等多种表征方法对As中毒前后催化剂的物性结构、表面物质的存在形式以及氧化还原性能的对比研究,结果显示As₂O₃堵塞催化剂微孔结构,导致催化剂表面微孔数量的减少,As₂O₅涂覆催化剂表面,进而阻碍了气相成分参与多相催化反应;As的引入使得表面形貌略有变差,并未导致催化剂晶型的变化,且As及其化合物在催化剂表面分散度较高.As会与催化剂表面的羟基作用形成As-OH,抑制催化剂酸性,尤其对Lewis酸的抑制效果明显;As中毒后的催化氧化还原能力增强.     

Conversion of alkylmercaptans in the presence of γ-Al2O3

In the presence of -Al₂O₃ at 200–500°C methylmercaptans quantitatively transform into dimethyl sulfides with almost equilibrium degrees of conversion. 100% selectivity towards diethyl sulfide is observed when ethylmercaptan conversion amounts to about 50% of its equilibrium value. In more severe conditions, dimethyl- and diethyl sulfides convert with eliminating hydrocarbons and H₂S. Selectivity towards diisopropylsulfide is as high as 30% with isopropylmercaptane conversion up to 25%; the reaction follows a parallel-consecutive scheme.

---

-Al₂O₃ 200–500°C . 100% 50% . - H₂S. 30% 25%, - .