Development of novel Ag/bauxite nanocomposite as a heterogeneous catalyst for biodiesel production

Ag/bauxite nanocomposites have been prepared using in situ reduction of aqueous AgNO₃ solution in a bauxite matrix and investigated for the transesterification of sunflower oil with methanol in order to study their potential as heterogeneous catalysts. The prepared nanocopmosites were characterized by XRD, SEM, EDX, FT-IR, and TG- DTA. The Central Composite Design of the Response Surface Methodology was used to optimize the effect of reaction temperature, reaction time, catalyst loading and methanol to oil molar ratio on the yield of fatty acid methyl esters. The highest yield was obtained at 67 °C reaction temperature, 3 h reaction time, 0.3 wt.% catalyst loading and 9:1 methanol to oil molar ratio. Under the optimal conditions, the methyl ester content was 94% and the catalyst successfully reused for at least 7 cycles without significant deactivation.     

Surfactant mediated enhanced glycerol uptake and hydrogen production from biodiesel waste using co-culture of Enterobacter aerogenes and Clostridium butyricum

In the present study, Tween 80, a non-ionic surfactant, has been used for enhanced hydrogen production by crude glycerol bioconversion using co-culture of Enterobacter aerogenes and Clostridium butyricum. The purpose of introducing the surfactant was to decrease the crude glycerol viscosity, so that apparent solubility and bioavailability of glycerol could be improved at the expenses of pretreatment steps. Experiments were planned using central composite design (CCD); crude glycerol and Tween 80 concentrations were optimized whereas, hydrogen production, glycerol utilization and viscosity of the media were considered as responses. The response surface for quadratic model showed, Tween 80 concentration had significant effect (p < 0.05) on all the three responses. Using the optimized conditions at 17.5 g/L crude glycerol and 15 mg/L Tween 80, hydrogen production reached a maximum of 32.1 ± 0.03 mmol/L of medium. The increase in hydrogen production was around 1.25-fold in presence of Tween 80 in comparison to its absence with 25.56 ± 0.91 mmol/L production. Selected optimum conditions were also validated against absence of crude glycerol (4.69 ± 0.76), with pretreated crude glycerol (20.06 ± 0.51) and across mono-culture system (15.43 ± 0.79 to 22.14 ± 0.94). Introduction of Tween 80 to the fermentation medium improved the glycerol utilization rate, resulting in increased hydrogen production and eliminated pretreatment steps.     

The improved CO2 capture system with heat recovery based on absorption heat transformer and flash evaporator

Absorption heat transformer (AHT) and flash evaporator (FE) are used to reduce the heat consumption of CO₂ capture processes and an AHT–FE-aided capture system is proposed. Analyses are carried out to verify the effectiveness in reducing heat consumption. Compared with the base CO₂ capture system of 3000 t/d CO₂ capture capacity from a 660 MW coal-fired power unit, the AHT–FE-aided capture system reduces the heat consumption from 3.873 GJ/tCO₂ to 3.772 GJ/tCO₂, and the corresponding energy saving is 2.62%. The economic analysis shows that the annual profit would be 2.94 million RMB Yuan. The payback period of the AHT–FE-aided capture system is approximately 2.4 years. Therefore, the AHT–FE-aided capture system is both economically and technically feasible for improving the CO₂ capture energy performance.     

Enhancement of lipid productivity in green microalgae Chlorella sp. via fast neutron irradiation

Microalgae is becoming a promising candidate for biofuel production and energetic lipid production, which urges the need to develop efficient methods for improvement of the lipid production. In this study, the neutron irradiation was employed to improve lipid production under different dosage irradiation. Effects of different dosages (No.1:8.14 × 10⁹, No.2:5.64 × 10⁸, No.4:9.42 × 10⁷ n/cm²) were compared by investigating associated algae cell growth, total lipid production, metabolization and enzyme activity. Dosages No.2 and No.4 improved the lipid content without negative influence on the growing, whereas irradiations shortened the period of biomass accumulation. The neutron irradiation in No.2 accelerated the synthesis of lipid from the carbohydrate transition process. In addition, the neutron irradiation not only increased the total lipid production by 20% but also speeded up the reaction rate to reach the maximal total lipid production in 28 days. Our results can provide a better understanding of the lipid production in microalgae Chlorella sp. by neutron irradiation, which are critical for evaluation of neutron irradiation based technologies for the sustainable and renewable biofuel production.     

An oil palm-based biorefinery concept for cellulosic ethanol and phytochemicals production: Sustainability evaluation using exergetic life cycle assessment

In this study, thermo-environmental sustainability of an oil palm-based biorefinery concept for the co-production of cellulosic ethanol and phytochemicals from oil palm fronds (OPFs) was evaluated based on exergetic life cycle assessment (ExLCA). For the production of 1 tonne bioethanol, the exergy content of oil palm seeds was upgraded from 236 MJ to 77,999 MJ during the farming process for OPFs production. Again, the high exergy content of the OPFs was degraded by about 62.02% and 98.36% when they were converted into cellulosic ethanol and phenolic compounds respectively. With a total exergy destruction of about 958,606 MJ (internal) and 120,491 MJ (external or exergy of wastes), the biorefinery recorded an overall exergy efficiency and thermodynamic sustainability index (TSI) of about 59.05% and 2.44 per tonne of OPFs' bioethanol respectively. Due to the use of fossil fuels, pesticides, fertilizers and other toxic chemicals during the production, the global warming potential (GWP = 2265.69 kg CO₂ eq.), acidification potential (AP = 355.34 kg SO₂ eq.) and human toxicity potential (HTP = 142.79 kg DCB eq.) were the most significant environmental impact categories for a tonne of bioethanol produced in the biorefinery. The simultaneous saccharification and fermentation (SSF) unit emerged as the most exergetically efficient (89.66%), thermodynamically sustainable (TSI = 9.67) and environmentally friendly (6.59% of total GWP) production system.     

Breakeven price of biomass from switchgrass,big bluestem,and Indiangrass in a dual-purpose production system in Tennessee

The objective was to determine the breakeven price for switchgrass (SG) (Panicum virgatum L.), a mix of big bluestem (Andropogon gerardii Vitman) and Indiangrass (BBIG) (Sorghastrum nutans L. Nash), and a combination of SG and BBIG (SG/BBIG) produced under three harvest treatments. Two-harvest treatments included a forage harvest at early boot (EB) and at early seedhead (ESH) plus a biomass harvest at fall dormancy (FD). The third harvest treatment was a single biomass harvest at FD. Mixed models were used to determine if there were differences in yield, crude protein, and nutrient removal for each of the native warm-season grass (NWSG) treatments at each harvest. The EB plus FD harvest system would be preferred over the ESH plus FD harvest system for all NWSG treatments. BBIG was the only NWSG treatment with a breakeven price for biomass that decreased with an EB harvest. For all three NWSG treatments, a producer would be better off harvesting once a year for biomass than twice for forage and biomass. The cost of harvesting and replacing the nutrients for the forage harvest was greater than the revenue received from selling the forage.     

Fuel property enhancement of biodiesel fuels from common and alternative feedstocks via complementary blending

Fatty acid methyl esters (biodiesel) prepared from field pennycress and meadowfoam seed oils were blended with methyl esters from camelina, cottonseed, palm, and soybean oils in an effort to ameliorate technical deficiencies inherent to these biodiesel fuels. For instance, camelina, cottonseed, and soybean oil-derived biodiesels exhibited poor oxidative stabilities but satisfactory kinematic viscosities. Field pennycress and meadowfoam seed oil methyl esters yielded excellent cold flow properties but high kinematic viscosities. Thus, field pennycress and meadowfoam-derived biodiesel fuels were blended with the other biodiesels to simultaneously ameliorate cold flow, oxidative stability, and viscosity deficiencies inherent to the individual fuels. Highly linear correlations were noted between blend ratio and cold flow as well as viscosity after least squares statistical regression whereas a non-linear relationship was observed for oxidative stability. Equations generated from statistical regression were highly accurate at predicting KV, reasonably accurate for prediction of cold flow properties, and less accurate at predicting oxidative stability. In summary, complementary blending enhanced fuel properties such as cold flow, kinematic viscosity, and oxidative stability of biodiesel.     

Sweet sorghum as a whole-crop feedstock for ethanol production

The potential of sweet sorghum as an alternative crop for ethanol production was investigated in this study. Initially, the enzymatic hydrolysis of sorghum grains was optimized, and the hydrolysate produced under optimal conditions was used for ethanol production with an industrial strain of Saccharomyces cerevisiae, resulting in an ethanol concentration of 87 g L⁻¹. From the sugary fraction (sweet sorghum juice), 72 g L⁻¹ ethanol was produced. The sweet sorghum bagasse was submitted to acid pretreatment for hemicellulose removal and hydrolysis, and a flocculant strain of Scheffersomyces stipitis was used to evaluate the fermentability of the hemicellulosic hydrolysate. This process yielded an ethanol concentration of 30 g L⁻¹ at 23 h of fermentation. After acid pretreatment, the remaining solid underwent an alkaline extraction for lignin removal. This partially delignified material, known as partially delignified lignin (PDC), was enriched with nutrients in a solid/liquid ratio of 1 g/3.33 mL and subjected to simultaneous saccharification and fermentation (SSF) process, resulting in an ethanol concentration of 85 g L⁻¹ at 21 h of fermentation. Thus, from the conversion of starchy, sugary and lignocellulosic fractions approximately 160 L ethanol.ton⁻¹ sweet sorghum was obtained. This amount corresponds to 13,600 L ethanol.ha⁻¹.     

Improving methane production from wheat straw by digestate liquor recirculation in continuous stirred tank processes

Wheat straw is an abundant, cheap substrate that can be used for methane production. However, the nutrient content in straw is inadequate for methane fermentation. In this study, recycling digestate liquor was implemented in single-stage continuous stirred tank processes for enrichment of the nutrient content of straw with the aim of improving the methane production. The VS-based organic loading rate was set at 2 g/(L d) and the solid retention time at 40 days. When wheat straw alone was used as the substrate, the methane yields achieved with digestate liquor recycling was on average 240 ml CH₄/g VS giving a 21% improvement over the processes without recycling. However, over time, the processes suffered from declining methane yields and poor stability evidenced by low pH. To maintain process stability, wheat straw was co-digested with sewage sludge or supplemented with macronutrients (nitrogen and phosphorous). As a result, the processes with digestate liquor recycling could be operated stably, achieving methane yields ranging from 288 to 296 ml CH₄/g VS. Besides, the processes could not be operated sturdily with supplementation of macronutrients without digestate liquor recycling. The highest methane yield (296 ± 16 ml CH₄/g VS) was achieved by co-digestion with sewage sludge plus recycling of digestate liquor after filtration (retention of nutrients and microorganisms). This was comparable to the maximum expected methane yield of 293 ± 13 ml CH₄/g VS achieved in batch test. The present study therefore demonstrated that digestate liquor recycling could lead to a decreased dilution of vital nutrients from the reactors thereby rendering high process performance and stability.     

Optimizing feedstock selection for biofuel production in Hawaii: CuO oxidative lignin products in C4 grasses

Global interest in renewable fuels is rapidly growing with particular emphasis on local energy growth and creating new energy feedstocks, specifically liquid fuel sources. However, the interactive effect of plant species/variety and growth environment on plant structural components, which may influence conversion efficiency and thus play an important role in optimizing the production of biofuels, is not fully understood. In this study cupric oxide (CuO) extractable lignin, which extracts and quantifies lignin-derived monomers, was determined for 25 cultivated and naturalized tropical perennial C₄ grass varieties of napiergrass and Guinea grass that were under assessment for suitability as feedstocks for liquid fuel generation. Principal component analysis of CuO extractable lignin-derived monomers showed differences in composition between napiergrass and Guinea grass, as well as environmental differences within many, but not all napiergrass varieties. Among the samples tested, the greatest differences in lignin composition occurred specifically in vanillyl lignin structures. A wide range (1–2.5) in the ratio of cinnamyl to vanillyl structures (C/V), which often relates to enzymatic degradability in natural systems, was also found. It is expected that the observed CuO lignin differences representing the structure and bonding of lignin will relate to ease of chemical and enzymatic conversion and the effectiveness of pretreatment and conversion in biofuel application. We hypothesize that the C/V ratio of feedstock will positively relate to conversion efficiency and if supported, then compositional lignin metrics such as the C/V ratio could be a predictor to select for more easily degradable biomass for biofuel production.     

Characterization,pretreatment and saccharification of spent seaweed biomass for bioethanol production using baker's yeast

Seaweeds are marine macroalgae found abundantly and viewed as potential source of phycocolloids to produce biofuel. In this study, seaweed spent biomass obtained from alginate production industry and biomass obtained after pigment extraction were found to contain a considerable amount of phycocolloids. These two spent biomasses were investigated for the production of ethanol. In this study, the red seaweed spent biomass of Gracilaria corticata var corticata showed higher content of polysaccharide (190.71 ± 30.67 mg g⁻¹ dry weight) than brown seaweed spent biomass (industrial) (136.28 ± 30.09 mg g⁻¹ dry weight). Hydrolysis of spent biomasses with different concentrations of sulfuric acid (0.1%, 0.5% and 1%) was also investigated. Brown seaweed spent biomass and red seaweed spent biomass exhibited high amount of sugar in 0.5% and 1% sulfuric acid treatment, respectively. Proximate and ultimate composition of seaweed spent biomasses were analysed for energy value. The FT-Raman spectra exhibited similar stretches for both acid hydrolysed spent biomasses with their respective standards. Ethanol produced through a fermentation process using spent hydrolysates with baker's yeast at pH 5.3 was found to be significant. The ethanol yield from brown seaweed spent biomass and red seaweed spent biomass was observed to be 0.011 g g⁻¹ and 0.02 ± 0.003 g g⁻¹ respectively, when compared with YPD (0.42 ± 0.03 g g⁻¹) and d-galactose (0.37 ± 0.04 g g⁻¹) as standard on day 4. The present study revealed the possibility of effective utilization of spent biomass from seaweed industry for ethanol production.     

Growth,yield, fiber content and lodging resistance in eight varieties of Cenchrus purpureus (Schumach.) Morrone intended as energy crop

Growth, biomass yield, fiber content and lodging resistance were studied, during a six month growth period, for eight varieties of Cenchrus purpureus, intended as energy crop, in Veracruz, Mexico. Then, only yield at day 182 was assessed for two additional years. The varieties were: CT115 (CT), African Cane (AC), Taiwan (TAI), King Grass (KG), Vruckwona (VRU), Roxo (RX), OM22 (OM) and Cameroon (CAM). Local weather is warm and sub-humid, historical data for monthly average temperature and annual rainfall were 25.8 °C and 1142 mm, respectively. Height, diameter and light interception were measured monthly from day 65–185. At day 185, biomass yield and tiller density were measured. Number of lying tillers was counted to estimate lodging resistance. Cellulose and hemicellulose content were estimated in leaf and stem. No differences were found for dry matter yield or stem yield at day 185 in the first year. Regarding the next two years, TAI yielded above CT, OM or ROX. Average dry matter yield was higher in the second year than in the establishment cycle (38.6 vs 21.1 Mg ha⁻¹), but decreased in the third year (32.2 Mg ha⁻¹). In both stem and whole plant, AC and KG showed higher hemicellulose content than RX, OM or CT; while AC and VRU had higher cellulose than RX in stem, or than CT in the whole plant. Furthermore, varieties AC, KG, VRU and TAI were resistant to lodging and had a higher fiber content, so they are recommended as energetic crops.     

A re-look at the biochemical strategies to enhance butanol production

Butanol produced from renewable feedstock is defined as an emerging biofuel and biochemical. Research efforts made during the last three decades on biochemical production of butanol via conventional ABE (acetone-ethanol-butanol) fermentation has tried to bring biobutanol close to competition with petrobutanol. However, each new effort of development has been often countered by new challenges, confining biobutanol production mostly to the laboratory scale. This review provides a systematic, comparative analysis of different steps in biochemical production of butanol and identifies the counteractive aspects and challenges to overcome. A special emphasis is given on process inhibitors, applied detoxification techniques, chemical supplements and research & development in industry in order to enhance and update ABE fermentation and make it cost effective. Biobutanol future lies in utilization of inexpensive cellulose enriched lignocellulosic hydrolysates and hyper-butanol producing bacteria, combined with specific detoxification techniques and followed by efficient continuous fermentation technologies together with in situ product recovery.     

Mild alkaline pre-treatments loosen fibre structure enhancing methane production from biomass crops and residues

Three ligno-cellulosic substrates representing varying levels of biodegradability (giant reed, GR; fibre sorghum, FS; barley straw, BS) were combined with mild alkaline pre-treatments (NaOH 0.05, 0.10 and 0.15 N at 25 °C for 24 h) plus untreated controls, to study pre-treatment effects on physical-chemical structure, anaerobic digestibility and methane output of the three substrates. In a batch anaerobic digestion (AD) assay (58 days; 35 °C; 4 g VS l⁻¹), the most recalcitrant substrate (GR) staged the highest increase in cumulative methane yield: +30% with NaOH 0.15 N over 190 ml CH₄ g⁻¹ VS in untreated GR. Conversely, the least recalcitrant substrate (FS) exhibited the lowest gain (+10% over 248 ml CH₄ g⁻¹ VS), while an intermediate behaviour was shown by BS (+15% over 232 ml CH₄ g⁻¹ VS). Pre-treatments speeded AD kinetics and reduced technical digestion time (i.e., the time needed to achieve 80% methane potential), which are the premises for increased production capacity of full scale AD plants. Fibre components (cellulose, hemicellulose and acid insoluble lignin determined after acid hydrolysis) and substrate structure (Fourier transform infra-red spectroscopy and scanning electron microscopy) outlined reductions of the three fibre components after pre-treatments, supporting claims of loosened binding of lignin with cellulose and hemicellulose. Hence, mild alkaline pre-treatments were shown to improve the biodegradability of ligno-cellulosic substrates to an extent proportional to their recalcitrance. In turn, this contributes to mitigate the food vs. fuel controversy raised by the use of whole plant cereals (namely, maize) as feedstocks for biogas production.     

Hydrogen,ethanol and cellulase production from pulp and paper primary sludge by fermentation with Clostridium thermocellum

Pulp and paper industry primary sludge being largely composed of lignocellulosic fibres, it could be used as carbon source by bacteria having cellulolytic capability. The aim of this study was to evaluate the use of cellulose contained in this type of sludge for Clostridium thermocellum to produce ethanol, hydrogen and cellulases. In an ATCC 1191 medium containing 5 kg m⁻³ dry primary sludge from recycled paper mill, batch culture reached stationary phase after 2 days. All of the available cellulose was hydrolysed after 60 h of incubation, with a final pH of 5.83. Metabolites produced after 60 h of fermentation were acetate (8.50 mol m⁻³), ethanol (11.30 mol m⁻³), lactate (8.75 mol m⁻³), formate (0.27 mol m⁻³), hydrogen (11.20 mol m⁻³) and carbon dioxide (18.41 mol m⁻³). Cellulase activity was detected in the supernatant after 36 h, with a maximal activity of 0.25 U cm⁻³ at 72 h. Pulp and paper primary sludge appeared to be a readily usable substrate for C. thermocellum at this concentration, yielding both potential biofuels (hydrogen and ethanol) as well as active cellulases.     

Combined ethanol and methane production from switchgrass (Panicum virgatum L.) impregnated with lime prior to steam explosion

Pretreatments are crucial to achieve efficient conversion of lignocellulosic biomass to soluble sugars. In this light, switchgrass was subjected to 13 pretreatments including steam explosion alone (195 °C for 5, 10 and 15 min) and after impregnation with the following catalysts: Ca(OH)₂ at low (0.4%) and high (0.7%) concentration; Ca(OH)₂ at high concentration and higher temperature (205 °C for 5, 10 and 15 min); H₂SO₄ (0.2% at 195 °C for 10 min) as reference acid catalyst before steam explosion. Enzymatic hydrolysis was carried out to assess pretreatment efficiency in both solid and liquid fraction. Thereafter, in selected pretreatments the solid fraction was subjected to simultaneous saccharification and fermentation (SSF), while the liquid fraction underwent anaerobic digestion (AD). Lignin removal was lowest (12%) and highest (35%) with steam alone and 0.7% lime, respectively. In general, higher cellulose degradation and lower hemicellulose hydrolysis were observed in this study compared to others, depending on lower biomass hydration during steam explosion. Mild lime addition (0.4% at 195 °C) enhanced ethanol in SSF (+28% than steam alone), while H₂SO₄ boosted methane in AD (+110%). However, methane represented a lesser component in combined energy yield (ethanol, methane and energy content of residual solid). Mild lime addition was also shown less aggressive and secured more residual solid after SSF, resulting in higher energy yield per unit raw biomass. Decreased water consumption, avoidance of toxic compounds in downstream effluents, and post process recovery of Ca(OH)₂ as CaCO₃ represent further advantages of pretreatments involving mild lime addition before steam explosion.     

Analysis of technology improvement opportunities for a 1.5 MW wind turbine using a hybrid stochastic approach in life cycle assessment

This paper presents an analysis of potential technological advancements for a 1.5 MW wind turbine using a hybrid stochastic method to improve uncertainty estimates of embodied energy and embodied carbon. The analysis is specifically aimed at these two quantities due to the fact that LCA based design decision making is of utmost importance at the concept design stage. In the presented case studies, better results for the baseline turbine were observed compared to turbines with the proposed technological advancements. Embodied carbon and embodied energy results for the baseline turbine show that there is about 85% probability that the turbine manufacturers may have lost the chance to reduce carbon emissions, and 50% probability that they may have lost the chance to reduce the primary energy consumed during its manufacture. The paper also highlights that the adopted methodology can be used to support design decision making and hence is more feasible for LCA studies.     

Lignocellulosic ethanol production employing immobilized Saccharomyces cerevisiae in packed bed reactor

Most of ethanol production processes are limited by lower ethanol production rate and recyclability problem of ethanologenic organism. In the present study, immobilized co-fermenting Saccharomyces cerevisiae GSE1618 was employed for ethanol fermentation using rice straw enzymatic hydrolysate in a packed bed reactor (PBR). The immobilization of S. cerevisiae was performed by entrapment in Ca-alginate for optimization of ethanol production by varying alginic acid concentration, bead size, glucose concentration, temperature and hardening time. Remarkably, extra hardened beads (EHB) immobilized with S. cerevisiae could be used up to repeated 40 fermentation batches. In continuous PBR, maximum 81.82 g L⁻¹ ethanol was obtained with 29.95 g L⁻¹ h⁻¹ productivity with initial glucose concentration of 180 g L⁻¹ in feed at dilution rate of 0.37 h⁻¹. However, maximum ethanol concentration of 40.33 g L⁻¹ (99% yield) with 24.61 g L⁻¹ h⁻¹ productivity was attained at 0.61 h⁻¹ dilution rate in fermentation of un-detoxified rice straw enzymatic hydrolysate (REH). At commercial scale, EHB has great potential for continuous ethanol production with high productivity using lignocellulosic hydrolysate in PBR.     

Evaluation of dilute acid and alkaline pretreatments,enzymatic hydrolysis and fermentation of napiergrass for fuel ethanol production

Napiergrass (Pennisetum purpureum Schum.) is a promising low cost raw material which does not compete with food prices, has attractive yields and an environmentally friendly farming. Dilute sulfuric acid pretreatment of napiergrass was effective to obtain high yields of sugars and low level of degradation by-products from hemicellulose. Detoxification with Ca(OH)₂ removed inhibitors but showed sugars loss. An ethanol concentration of 21 g/L after 176 h was found from the hydrolyzate using Pichia stipitis NBRC 10063 (fermentation efficiency 66%). An additional alkaline pretreatment applied to the solid fraction remaining from the diluted acid pretreatment improved the lignin removal. The highest cellulose hydrolysis values were found with the addition of β-glucosidase and PEG 6000. The simultaneous hydrolysis and fermentation of the cellulosic fraction with Saccharomyces cerevisiae, 10% (w/v) solid concentration, β-glucosidase and PEG 6000, showed the highest ethanol concentration (24 g/L), and cellulose hydrolysis values (81%). 162 L ethanol/t of dry napiergrass were produced (overall efficiency of 52%): 128 L/t from the cellulosic fraction and 34 L/t from the hemicellulosic fraction.     

Wind tunnel test for the NREL phase VI rotor with 2 m diameter

The aerodynamic performance of the ‘NREL Phase VI’ rotor with a 2 m diameter was tested in the open jet test section. The original rotor with a 10.06 m diameter was tested in the NASA Ames tunnel and the test result was used as validation data for the computational model. The Reynolds number of the sectional airfoils in the original test is around 1.0E6 which is too high for a conventional wind tunnel with a diameter less than 5 m. The wind tunnel test to study the Reynolds number effect on the rotor performance from Re = 0.1E6 to Re = 0.4E6 was conducted in the KARI low speed wind tunnel with a 5 m × 3.75 m open jet test section. The torque generated by the blade was directly measured by the sensor installed in the rotating axis. The variation of the Reynolds number was achieved by changing the rotational speed. Two surface conditions, free transition and forced transition were employed in this test to study the surface trip effect. The test results for the free transition condition show that the power coefficient, Cp gradually increases with the Reynolds number, but the Cp for the forced transition condition does not vary with the Reynolds number. The maximum Cp for the free transition is 0.30 and it decrease to 0.22 for the forced transition conditions at the Reynolds number 0.4E6. The downstream flow velocity measured by 5-hole probe in the wind tunnel test was compared with BEMT calculation result. The comparison results show that the torque dependency on Reynolds number in the blade is mainly originated from the airfoil drag characteristics. A model to estimate the power of full scale blade was suggested based on these measurement results. The estimated power shows a good agreement with the full scale test result.