Simulation design of normally-off AlGaN/GaN high-electron-mobility transistors with p-GaN Schottky hybrid gate

A novel normally-off AlGaN/GaN high-electron-mobility transistor (HEMT) with a p-GaN Schottky hybrid gate (PSHG) is proposed, and compared with the conventional p-GaN normally-off AlGaN/GaN HEMTs. This structure can be realized by selective etching of p-GaN layer, which enables the Schottky junction and PN junction to control the channel charge at the same time. The direct current (DC) and switching characteristics of the PSHG HEMTs are simulated by Slivaco TCAD, and the p-GaN HEMTs and conventional normally-on HEMTs are also simulated for comparison. The simulation results show that the PSHG HEMTs have a higher current density and a lower on-resistance than p-GaN HEMTs, which is more obvious with the decrease of p-GaN ratios of the PSHG HEMTs. The breakdown voltage and threshold voltage of the PSHG HEMTs are very close to those of the p-GaN HEMTs. In addition, the PSHG HEMTs have a higher switching speed than the conventional normally-on HEMTs, and the p-GaN layer ratio has no obvious effect on the switching speed.     

Investigation on threshold voltage of p-channel GaN MOSFETs based on p-GaN/AlGaN/GaN heterostructure

The threshold voltage (V_th) of the p-channel metal-oxide-semiconductor field-effect transistors (MOSFETs) is investigated via Silvaco-Atlas simulations. The main factors which influence the threshold voltage of p-channel GaN MOSFETs are barrier height Φ_1,p, polarization charge density σ_b, and equivalent unite capacitance C_oc. It is found that the thinner thickness of p-GaN layer and oxide layer will acquire the more negative threshold voltage V_th, and threshold voltage |V_th| increases with the reduction in p-GaN doping concentration and the work-function of gate metal. Meanwhile, the increase in gate dielectric relative permittivity may cause the increase in threshold voltage |V_th|. Additionally, the parameter influencing output current most is the p-GaN doping concentration, and the maximum current density is 9.5 mA/mm with p-type doping concentration of 9.5×10¹⁶ cm^-3 at V_GS = -12 V and V_DS = -10 V.     

具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管

介绍了一种具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管。采用原子层淀积(ALD)方法实现Al₂O₃栅介质的沉积。槽栅常关型AlGaN/GaN MOS-HEMT的栅长(L_g)为2 μm,栅宽(W_g)为0.9 mm(0.45 mm×2),栅极和源极(L_gs)之间的距离为5 μm,栅极和漏极(L_gd)之间的距离为10 μm。在栅压为－20 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电仅为0.65 nA。在栅压为+12 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电为225 nA。器件的栅压摆幅为－20~+12 V。在栅压V_gs=+10 V时,槽栅常关型AlGaN/GaN MOS-HEMT电流和饱和电流密度分别达到了98 mA和108 mA/mm (W_g=0.9 mm), 特征导通电阻为4 mΩ·cm²。槽栅常关型AlGaN/GaN MOS-HEMT的阈值电压为+4.6 V,开启与关断电流比达到了5×10⁸。当V_ds=7 V时,器件的峰值跨导为42 mS/mm (W_g=0.9 mm,V_gs=+10 V)。在V_gs=0 V时,栅漏间距为10 μm的槽栅常关型AlGaN/GaN MOS-HEMT的关断击穿电压为450 V,关断泄露电流为0.025 mA/mm。     

1000 V p-GaN混合阳极AlGaN/GaN二极管

GaN材料具有优异的电学特性,如大的禁带宽度(3.4 eV)、高击穿场强(3.3 MV/cm)和高电子迁移率(600 cm~2/(V·s)). AlGaN/GaN异质结由于压电极化和自发极化效应,产生高密度(1×10~(13)cm~(-2))和高迁移率(2000 cm~2/(V·s))的二维电子气(2DEG),在未来的功率系统中, AlGaN/GaN二极管具有极大的应用前景.二极管的开启电压和击穿电压是影响其损耗和功率处理能力的关键参数,本文提出了一种新型的具有高阻盖帽层(high-resistance-cap-layer, HRCL)的p-GaN混合阳极AlGaN/GaN二极管来优化其开启电压和击穿特性.在p-GaN/AlGaN/GaN材料结构基础上,通过自对准的氢等离子体处理技术,在沟道区域形成高阻盖帽层改善电场分布,提高击穿电压,同时在阳极区域保留p-GaN结构,用于耗尽下方的二维电子气,调控开启电压.制备的p-GaN混合阳极(p-GaN HRCL)二极管在阴阳极间距Lac为10μm时,击穿电压大于1 kV,开启电压+1.2 V.实验结果表明, p-GaN混合阳极和高阻GaN盖帽层的引入,有效改善AlGaN/GaN肖特基势垒二极管电学性能.     

Influence of Schottky drain contacts on the strained AlGaN barrier layer of AlGaN/AlN/GaN heterostructure field-effect transistors

Rectangular Schottky drain AlGaN/AlN/GaN heterostructure field-effect transistors (HFETs) with different gate contact areas and conventional AlGaN/AlN/GaN HFETs as control were both fabricated with same size. It was found there is a significant difference between Schottky drain AlGaN/AlN/GaN HFETs and the control group both in drain series resistance and in two-dimensional electron gas (2DEG) electron mobility in the gate-drain channel. We attribute this to the different influence of Ohmic drain contacts and Schottky drain contacts on the strained AlGaN barrier layer. For conventional AlGaN/AlN/GaN HFETs, annealing drain Ohmic contacts gives rise to a strain variation in the AlGaN barrier layer between the gate contacts and the drain contacts, and results in strong polarization Coulomb field scattering in this region. In Schottky drain AlGaN/AlN/GaN HFETs, the strain in the AlGaN barrier layer is distributed more regularly.     

Fabrication and characterization of the normally-off N-channel lateral 4H–SiC metal–oxide–semiconductor field-effect transistors

In this paper, the normally-off N-channel lateral 4H–Si C metal–oxide–semiconductor field-effect transistors(MOSFFETs) have been fabricated and characterized. A sandwich-(nitridation–oxidation–nitridation) type process was used to grow the gate dielectric film to obtain high channel mobility. The interface properties of 4H–Si C/SiO_2 were examined by the measurement of HF I–V, G–V, and C–V over a range of frequencies. The ideal C–V curve with little hysteresis and the frequency dispersion were observed. As a result, the interface state density near the conduction band edge of 4H–Si C was reduced to 2 × 10~(11) e V~(-1)·cm~(-2), the breakdown field of the grown oxides was about 9.8 MV/cm, the median peak fieldeffect mobility is about 32.5 cm~2·V~(-1)·s~(-1), and the maximum peak field-effect mobility of 38 cm~2·V~(-1)·s~(-1) was achieved in fabricated lateral 4H–Si C MOSFFETs.     

具有p-GaN岛状埋层耐压结构的横向AlGaN/GaN高电子迁移率晶体管

GaN基高电子迁移率晶体管(HEMT)相对较低的击穿电压严重限制了其大功率应用.为了进一步改善器件的击穿特性,通过在n-GaN外延缓冲层中引入六个等间距p-GaN岛掩埋缓冲层(PIBL)构成p-n结,提出一种基于p-GaN埋层结构的新型高耐压AlGaN/GaN HEMT器件结构.Sentaurus TCAD仿真结果表明,在关态高漏极电压状态下,p-GaN埋层引入的多个反向p-n结不仅能够有效调制PIBL AlGaN/GaN HEMT的表面电场和体电场分布,而且对于缓冲层泄漏电流有一定的抑制作用,这保证了栅漏间距为10μm的PIBL HEMT能够达到超过1700 V的高击穿电压(BV),是常规结构AlGaN/GaN HEMT击穿电压(580 V)的3倍.同时,PIBL结构AlGaN/GaN HEMT的特征导通电阻仅为1.47 m?·cm~2,因此获得了高达1966 MW·cm~(-2)的品质因数(FOM=BV~2/R_(on,sp)).相比于常规的AlGaN/GaN HEMT,基于新型p-GaN埋岛结构的HEMT器件在保持较低特征导通电阻的同时具有更高的击穿电压,这使得该结构在高功率电力电子器件领域具有很好的应用前景.     

基于原位等离子体氮化及低压化学气相沉积-Si_3N_4栅介质的高性能AlGaN/GaN MIS-HEMTs器件的研究

通过对低压化学气相沉积(LPCVD)系统进行改造,实现在沉积Si_3N_4薄膜前的原位等离子体氮化处理,氮等离子体可以有效地降低器件界面处的氧含量和悬挂键,从而获得了较低的LPCVD-Si_3N_4/GaN界面态,通过这种技术制作的MIS-HEMTs器件,在扫描栅压范围V_(G-sweep)=(-30 V,+24 V)时,阈值回滞为186 mV,据我们所知为目前高扫描栅压V_(G+)(20 V)下的最好结果.动态测试表明,在400 V关态应力下,器件的导通电阻仅仅上升1.36倍(关态到开态的时间间隔为100μs).     

Electron mobility in the linear region of an AlGaN/AlN/GaN heterostructure field-effect transistor

We simulate the current-voltage （I-V） characteristics of AlGaN/AlN/GaN heterostructure field-effect transistors （HFETs） with different gate lengths using the quasi-two-dimensional （quasi-2D） model. The calculation results obtained using the modified mobility model are found to accord well with the experimental data. By analyzing the variation of the electron mobility for the two-dimensional electron gas （213EG） with the electric field in the linear region of the AlGaN/AlN/GaN HFET I-V output characteristics, it is found that the polarization Coulomb field scattering still plays an important role in the electron mobility of AlGaN/AlN/GaN HFETs at the higher drain voltage and channel electric field. As drain voltage and channel electric field increase, the 2DEG density reduces and the polarization Coulomb field scattering increases, as a result, the 2DEG electron mobility decreases.     

阶梯AlGaN外延新型Al0.25Ga0.75N/GaNHEMTs器件实验研究

本文报道了作者提出的阶梯AlGaN外延层新型AlGaN/GaN HEMTs结构的实验结果. 实验利用感应耦合等离子体刻蚀(ICP)刻蚀栅边缘的AlGaN外延层, 形成阶梯的AlGaN 外延层结构, 获得浓度分区的沟道2DEG, 使得阶梯AlGaN外延层边缘出现新的电场峰, 有效降低栅边缘的高峰电场, 从而优化了AlGaN/GaN HEMTs器件的表面电场分布. 实验获得了阈值电压-1.5 V的新型AlGaN/GaN HEMTs器件. 经过测试, 同样面积的器件击穿电压从传统结构的67 V提高到新结构的106 V, 提高了58%左右; 脉冲测试下电流崩塌量也比传统结构减少了30%左右, 电流崩塌效应得到了一定的缓解.     

Ferroelectric effect and equivalent polarization charge model of PbZr_(0.2)Ti_(0.8)O_3 on AlGaN/GaN MIS-HEMT

PbZr_(0.2)Ti_(0.8)O_3(PZT) gate insulator with the thickness of 30 nm is grown by pulsed laser deposition(PLD) in AlGa N/Ga N metal–insulator–semiconductor high electron mobility transistors(MIS-HEMTs). The ferroelectric effect of PZT Al Ga N/Ga N MIS-HEMT is demonstrated. The polarization charge in PZT varies with different gate voltages. The equivalent polarization charge model(EPCM) is proposed for calculating the polarization charge and the concentration of two-dimensional electron gas(2 DEG). The threshold voltage(Vth) and output current density(IDS) can also be obtained by the EPCM. The theoretical values are in good agreement with the experimental results and the model can provide a guide for the design of the PZT MIS-HEMT. The polarization charges of PZT can be modulated by different gate-voltage stresses and the Vthhas a regulation range of 4.0 V. The polarization charge changes after the stress of gate voltage for several seconds. When the gate voltage is stable or changes at high frequency, the output characteristics and the current collapse of the device remain stable.     

电离辐射对部分耗尽绝缘体上硅器件低频噪声特性的影响

本文针对辐射前后部分耗尽结构绝缘体上硅(SOI)器件的电学特性与低频噪声特性开展试验研究. 受辐射诱生埋氧化层固定电荷与界面态的影响, 当辐射总剂量达到1 M rad(Si) (1 rad = 10^-2 Gy)条件下, SOI器件背栅阈值电压从44.72 V 减小至12.88 V、表面电子有效迁移率从473.7 cm²/V·s降低至419.8 cm²/V· s、亚阈斜率从2.47 V/dec增加至3.93 V/dec; 基于辐射前后亚阈斜率及阈值电压的变化, 可提取得到辐射诱生界面态与氧化层固定电荷密度分别为5.33×10¹¹ cm^{- 2}与2.36×10¹² cm^-2. 受辐射在埋氧化层-硅界面处诱生边界陷阱、氧化层固定电荷与界面态的影响, 辐射后埋氧化层-硅界面处电子被陷阱俘获/释放的行为加剧, 造成SOI 器件背栅平带电压噪声功率谱密度由7×10^{- 10} V²·Hz^-1增加至1.8×10^-9 V² ·Hz^-1; 基于载流子数随机涨落模型可提取得到辐射前后SOI器件埋氧化层界面附近缺陷态密度之和约为1.42×10¹⁷ cm^-3·eV^-1和3.66×10¹⁷ cm^-3·eV^-1. 考虑隧穿削弱因子、隧穿距离与时间常数之间关系, 本文计算得到辐射前后埋氧化层内陷阱电荷密度随空间分布的变化.     

Determination of the series resistance under the Schottky contacts of AlGaN/AlN/GaN Schottky barrier diodes

Rectangular AlGaN/AlN/GaN heterostructure field-effect transistors (HFETs) were fabricated, and the gate and the source of the HFETs consisted of AlGaN/AlN/GaN Schottky barrier diodes (SBDs). Based on the measured forward current-voltage and the capacitance-voltage characteristics of the AlGaN/AlN/GaN SBDs, the series resistance under the Schottky contacts (R_S) was calculated using the method of power consumption, which has been proved to be valid. Finally, the method of power consumption for calculating R_S was successfully used to study the two-dimensional electron gas electron mobility for a series of circular AlGaN/AlN/GaN SBDs. It is shown that the series resistance under the Schottky contacts cannot be neglected and is important for analysing and characterizing the AlGaN/AlN/GaN SBDs and the AlGaN/AlN/GaN HFETs.     

Negative transconductance effect in p-GaN gate AlGaN/GaN HEMTs by traps in unintentionally doped GaN buffer layer

We investigate the negative transconductance effect in p-GaN gate AlGaN/GaN high-electron-mobility transistor(HEMT) associated with traps in the unintentionally doped GaN buffer layer. We find that a negative transconductance effect occurs with increasing the trap concentration and capture cross section when calculating transfer characteristics.The electron tunneling through AlGaN barrier and the reduced electric field discrepancy between drain side and gate side induced by traps are reasonably explained by analyzing the band diagrams, output characteristics, and the electric field strength of the channel of the devices under different trap concentrations and capture cross sections.     

具有部分本征GaN帽层新型AlGaN/GaN高电子迁移率晶体管特性分析

为了优化传统Al GaN/GaN高电子迁移率晶体管(high electron mobility transistors,HEMTs)器件的表面电场,提高击穿电压,本文提出了一种具有部分本征GaN帽层的新型Al GaN/GaN HEMTs器件结构.新型结构通过在Al GaN势垒层顶部、栅电极到漏电极的漂移区之间引入部分本征GaN帽层,由于本征GaN帽层和Al GaN势垒层界面处的极化效应,降低了沟道二维电子气(two dimensional electron gas,2DEG)的浓度,形成了栅边缘低浓度2DEG区域,使得沟道2DEG浓度分区,由均匀分布变为阶梯分布.通过调制沟道2DEG的浓度分布,从而调制了Al GaN/GaN HEMTs器件的表面电场.利用电场调制效应,产生了新的电场峰,且有效降低了栅边缘的高峰电场,Al GaN/GaN HEMTs器件的表面电场分布更加均匀.利用ISE-TCAD软件仿真分析得出:通过设计一定厚度和长度的本征GaN帽层,Al GaN/GaN HEMTs器件的击穿电压从传统结构的427 V提高到新型结构的960 V.由于沟道2DEG浓度减小,沟道电阻增加,使得新型Al GaN/GaN HEMTs器件的最大输出电流减小了9.2%,截止频率几乎保持不变,而最大振荡频率提高了12%.     

增强型AlGaN/GaN高电子迁移率晶体管高温退火研究

深入研究了两种增强型AlGaN/GaN高电子迁移率晶体管(HEMT)高温退火前后的直流特性变化.槽栅增强型AlGaN/GaN HEMT在500 ℃ N₂中退火5 min后,阈值电压由0.12 V正向移动到0.57 V,器件Schottky反向栅漏电流减小一个数量级.F注入增强型AlGaN/GaN HEMT在 400 ℃ N₂中退火2 min后,器件阈值电压由0.23 V负向移动到-0.69 V,栅泄漏电流明显增大.槽栅增强型器件退火过程中Schottky有效势垒     

Comparison of electrical characteristic between AlN/GaN and AlGaN/GaN heterostructure Schottky diodes

Ni/Au Schottky contacts on AlN/GaN and AlGaN/GaN heterostructures are fabricated.Based on the measured current–voltage and capacitance–voltage curves,the electrical characteristics of AlN/GaN Schottky diode,such as Schottky barrier height,turn-on voltage,reverse breakdown voltage,ideal factor,and the current-transport mechanism,are analyzed and then compared with those of an AlGaN/GaN diode by self-consistently solving Schrdinger’s and Poisson’s equations.It is found that the dislocation-governed tunneling is dominant for both AlN/GaN and AlGaN/GaN Schottky diodes.However,more dislocation defects and a thinner barrier layer for AlN/GaN heterostructure results in a larger tunneling probability,and causes a larger leakage current and lower reverse breakdown voltage,even though the Schottky barrier height of AlN/GaN Schottky diode is calculated to be higher that of an AlGaN/GaN diode.     

阶梯AlGaN外延新型Al_(0.25)Ga_(0.75)N/GaNHEMTs击穿特性分析

为了优化AlGaN/GaN HEMTs器件表面电场,提高击穿电压,本文首次提出了一种新型阶梯AlGaN/GaN HEMTs结构.新结构利用AlGaN/GaN异质结形成的2DEG浓度随外延AlGaN层厚度降低而减小的规律,通过减薄靠近栅边缘外延的AlGaN层,使沟道2DEG浓度分区,形成栅边缘低浓度2DEG区,低的2DEG使阶梯AlGaN交界出现新的电场峰,新电场峰的出现有效降低了栅边缘的高峰电场,优化了AlGaN/GaN HEMTs器件的表面电场分布,使器件击穿电压从传统结构的446 V,提高到新结构的640 V.为了获得与实际测试结果一致的击穿曲线,本文在GaN缓冲层中设定了一定浓度的受主型缺陷,通过仿真分析验证了国际上外延GaN缓冲层时掺入受主型离子的原因,并通过仿真分析获得了与实际测试结果一致的击穿曲线.     

Low-voltage blue light emission from n-ZnO/p-GaN heterojunction formed by RF magnetron sputtering method

High quality n-ZnO/p-GaN heterojunction was fabricated by growing highly crystalline ZnO epitaxial films on commercial p-type GaN substrates via radio frequency (RF) magnetron sputtering. Low-voltage blue light emitting diode with a turn-on voltage of ∼2.5 V from the n-ZnO/p-GaN heterojunction was demonstrated. The diode gives a bright blue light emission located at ∼460 nm and a low threshold voltage of 2.7 V for emission. Based on the results of the photoluminescence (PL) and electroluminescence (EL) spectra, the origins of the EL emissions were studied in the light of energy band diagrams of ZnO–GaN heterojunction, and may attribute to the radiative recombination of the holes in p-GaN and the electrons injected from n-ZnO, which almost happened on the side of p-GaN layer. These results may have important implications for developing short wavelength optoelectronic devices.     

N极性GaN/AlGaN异质结二维电子气模拟

通过自洽求解薛定谔方程和泊松方程,较系统地研究了GaN沟道层、AlGaN背势垒层、Si掺杂和AlN插入层对N极性GaN/AlGaN异质结中二维电子气(2DEG)的影响,分析表明,GaN沟道层厚度、AlGaN背势垒层厚度及Al组分变大都能一定程度上提高二维电子气面密度,AlGaN背势垒层的厚度和Al组分变大也可提高二维电子气限阈性,且不同的Si掺杂形式对二维电子气的影响也有差异,而AlN插入层在提高器件二维电子气面密度、限阈性等方面表现都较为突出,在模拟中GaN沟道层厚度小于5nm时无法形成二维电子气,超过20nm后二维电子气面密度趋于饱和,而AlGaN背势垒厚度超过40nm后二维电子气也有饱和趋势,对均匀掺杂和delta掺杂而言AlGaN背势垒层Si掺杂浓度超过5×10~(19)cm~(-3)后2DEG面密度开始饱和,而厚度为2nmAlN插入层的引入会使2DEG面密度从无AlN插入层时的0.93×10~(13)cm~(-2)提高到1.17×10~(13)cm~(-2)。