高场应力及栅应力下AlGaN/GaN HEMT器件退化研究

采用不同的高场应力和栅应力对AlGaN/GaN HEMT器件进行直流应力测试,实验发现：应力后器件主要参数如饱和漏电流,跨导峰值和阈值电压等均发生了明显退化,而且这些退化还是可以完全恢复的;高场应力下,器件特性的退化随高场应力偏置电压的增加和应力时间的累积而增大;对于不同的栅应力,相对来说,脉冲栅应力和开态栅应力下器件特性的退化比关态栅应力下的退化大.对不同应力前后器件饱和漏电流,跨导峰值和阈值电压的分析表明,AlGaN势垒层陷阱俘获沟道热电子以及栅极电子在栅漏间电场的作用下填充虚栅中的表面态是这些不同应 关键词： AlGaN/GaN HEMT器件 表面态(虚栅) 势垒层陷阱 应力     

AlGaN/GaN 高电子迁移率晶体管漏电流退化机理研究

本文首先制备了与AlGaN/GaN高电子迁移率晶体管 (HEMT) 结构与特性等效的AlGaN/GaN异质结肖特基二极管, 采用步进应力测试比较了不同栅压下器件漏电流的变化情况, 然后基于电流-电压和电容-电压测试验证了退化前后漏电流的传输机理, 并使用失效分析技术光发射显微镜 (EMMI) 观测器件表面的光发射, 研究了漏电流的时间依赖退化机理. 实验结果表明: 在栅压高于某临界值后, 器件漏电流随时间开始增加, 同时伴有较大的噪声. 将极化电场引入电流与电场的依赖关系后, 器件退化前后的 log(I_FT/E)与√E 都遵循良好的线性关系, 表明漏电流均由电子Frenkel-Poole (FP) 发射主导. 退化后 log(I_FT/E)与√E 曲线斜率的减小, 以及利用EMMI在栅边缘直接观察到了与缺陷存在对应关系的“热点”, 证明了漏电流退化的机理是: 高电场在AlGaN层中诱发了新的缺陷, 而缺陷密度的增加导致了FP发射电流I_FT的增加. 关键词： AlGaN/GaN 高电子迁移率晶体管 漏电流 退化机理     

Low power fluorine plasma effects on electrical reliability of AlGaN/GaN high electron mobility transistor

The new electrical degradation phenomenon of the AlGaN/GaN high electron mobility transistor(HEMT) treated by low power fluorine plasma is discovered. The saturated current, on-resistance, threshold voltage, gate leakage and breakdown voltage show that each experiences a significant change in a short time stress, and then keeps unchangeable. The migration phenomenon of fluorine ions is further validated by the electron redistribution and breakdown voltage enhancement after off-state stress. These results suggest that the low power fluorine implant ion stays in an unstable state. It causes the electrical properties of AlGaN/GaN HEMT to present early degradation. A new migration and degradation mechanism of the low power fluorine implant ion under the off-stress electrical stress is proposed. The low power fluorine ions would drift at the beginning of the off-state stress, and then accumulate between gate and drain nearby the gate side. Due to the strong electronegativity of fluorine, the accumulation of the front fluorine ions would prevent the subsequent fluorine ions from drifting, thereby alleviating further the degradation of AlGaN/GaN HEMT electrical properties.     

Breakdown mechanisms in AlGaN/GaN high electron mobility transistors with different GaN channel thickness values

In this paper,the off-state breakdown characteristics of two different AlGaN/GaN high electron mobility transistors（HEMTs）,featuring a 50-nm and a 150-nm GaN thick channel layer,respectively,are compared.The HEMT with a thick channel exhibits a little larger pinch-off drain current but significantly enhanced off-state breakdown voltage(SV_off).Device simulation indicates that thickening the channel increases the drain-induced barrier lowering（DIBL） but reduces the lateral electric field in the channel and buffer underneath the gate.The increase of BV_off in the thick channel device is due to the reduction of the electric field.These results demonstrate that it is necessary to select an appropriate channel thickness to balance DIBL and BV_off in AlGaN/GaN HEMTs.     

Improvement of breakdown characteristics of an A1GaN/GaN HEMT with a U-type gate foot for millimeter-wave power application

<正>In this study,the physics-based device simulation tool Silvaco ATLAS is used to characterize the electrical properties of an AlGaN/GaN high electron mobility transistor(HEMT) with a U-type gate foot.The U-gate AlGaN/GaN HEMT mainly features a gradually changed sidewall angle,which effectively mitigates the electric field in the channel, thus obtaining enhanced off-state breakdown characteristics.At the same time,only a small additional gate capacitance and decreased gate resistance ensure excellent RF characteristics for the U-gate device.U-gate AlGaN/GaN HEMTs are feasible through adjusting the etching conditions of an inductively coupled plasma system,without introducing any extra process steps.The simulation results are confirmed by experimental measurements.These features indicate that U-gate AlGaN/GaN HEMTs might be promising candidates for use in miltimeter-wave power applications.     

The effects of 60Co γ-ray irradiation on the DC characteristics of enhancement-mode AlGaN/GaN high-electron-mobility transistors

The effects of 60Co γ-ray irradiation on the DC characteristics of AlGaN/GaN enhancement-mode high-electron-mobility transistors (E-mode HEMTs) are investigated. The results show that having been irradiated by 60Co γ-rays at a dose of 3 Mrad (Si), the E-mode HEMT reduces its saturation drain current and maximal transconductance by 6% and 5%, respectively, and significantly increases both forward and reverse gate currents, while its threshold voltage is affected only slightly. The obvious performance degradation of E-mode AlGaN/GaN HEMTs is consistent with the creation of electronegative surface state charges in the source-gate spacer and gate-drain spacer after being irradiated.     

增强型AlGaN/GaN高电子迁移率晶体管高温退火研究

深入研究了两种增强型AlGaN/GaN高电子迁移率晶体管(HEMT)高温退火前后的直流特性变化.槽栅增强型AlGaN/GaN HEMT在500 ℃ N₂中退火5 min后,阈值电压由0.12 V正向移动到0.57 V,器件Schottky反向栅漏电流减小一个数量级.F注入增强型AlGaN/GaN HEMT在 400 ℃ N₂中退火2 min后,器件阈值电压由0.23 V负向移动到-0.69 V,栅泄漏电流明显增大.槽栅增强型器件退火过程中Schottky有效势垒     

阶梯AlGaN外延新型Al0.25Ga0.75N/GaNHEMTs器件实验研究

本文报道了作者提出的阶梯AlGaN外延层新型AlGaN/GaN HEMTs结构的实验结果. 实验利用感应耦合等离子体刻蚀(ICP)刻蚀栅边缘的AlGaN外延层, 形成阶梯的AlGaN 外延层结构, 获得浓度分区的沟道2DEG, 使得阶梯AlGaN外延层边缘出现新的电场峰, 有效降低栅边缘的高峰电场, 从而优化了AlGaN/GaN HEMTs器件的表面电场分布. 实验获得了阈值电压-1.5 V的新型AlGaN/GaN HEMTs器件. 经过测试, 同样面积的器件击穿电压从传统结构的67 V提高到新结构的106 V, 提高了58%左右; 脉冲测试下电流崩塌量也比传统结构减少了30%左右, 电流崩塌效应得到了一定的缓解.     

阶梯AlGaN外延新型Al_(0.25)Ga_(0.75)N/GaNHEMTs击穿特性分析

为了优化AlGaN/GaN HEMTs器件表面电场,提高击穿电压,本文首次提出了一种新型阶梯AlGaN/GaN HEMTs结构.新结构利用AlGaN/GaN异质结形成的2DEG浓度随外延AlGaN层厚度降低而减小的规律,通过减薄靠近栅边缘外延的AlGaN层,使沟道2DEG浓度分区,形成栅边缘低浓度2DEG区,低的2DEG使阶梯AlGaN交界出现新的电场峰,新电场峰的出现有效降低了栅边缘的高峰电场,优化了AlGaN/GaN HEMTs器件的表面电场分布,使器件击穿电压从传统结构的446 V,提高到新结构的640 V.为了获得与实际测试结果一致的击穿曲线,本文在GaN缓冲层中设定了一定浓度的受主型缺陷,通过仿真分析验证了国际上外延GaN缓冲层时掺入受主型离子的原因,并通过仿真分析获得了与实际测试结果一致的击穿曲线.     

Improved device performance of recessed-gate AlGaN/GaN HEMTs by using in-situ N2O radical treatment

The N₂O radicals in-situ treatment on gate region has been employed to improve device performance of recessed-gate AlGaN/GaN high-electron-mobility transistors (HEMTs). The samples after gate recess etching were treated by N₂O radicals without physical bombardment. After in-situ treatment (IST) processing, the gate leakage currents decreased by more than one order of magnitude compared to the sample without IST. The fabricated HEMTs with the IST process show a low reverse gate current of 10^-9 A/mm, high on/off current ratio of 10⁸, and high f_T×L_g of 13.44 GHz· μm. A transmission electron microscope (TEM) imaging illustrates an oxide layer with a thickness of 1.8 nm exists at the AlGaN surface. X-ray photoelectron spectroscopy (XPS) measurement shows that the content of the Al-O and Ga-O bonds elevated after IST, indicating that the Al-N and Ga-N bonds on the AlGaN surface were broken and meanwhile the Al-O and Ga-O bonds formed. The oxide formed by a chemical reaction between radicals and the surface of the AlGaN barrier layer is responsible for improved device characteristics.     

The effects of ⁶⁰Co γ-ray irradiation on the DC characteristics of enhancement-mode AlGaN/GaN high-electron-mobility transistors

The effects of 60Co γ-ray irradiation on the DC characteristics of AlGaN/GaN enhancement-mode high-electron-mobility transistors (E-mode HEMTs) are investigated. The results show that having been irradiated by 60Co γ-rays at a dose of 3 Mrad (Si), the E-mode HEMT reduces its saturation drain current and maximal transconductance by 6% and 5%, respectively, and significantly increases both forward and reverse gate currents, while its threshold voltage is affected only slightly. The obvious performance degradation of E-mode AlGaN/GaN HEMTs is consistent with the creation of electronegative surface state charges in the source-gate spacer and gate-drain spacer after being irradiated.     

The reliability of AlGaN/GaN high electron mobility transistors under step-electrical stresses

In spite of their extraordinary performance, AlGaN/GaN high electron mobility transistors (HEMTs) still lack solid reliability. Devices under accelerated DC stress tests (off-state, V_DS =0 state, and on-state step-stress) are investigated to help us identify the degradation mechanisms of the AlGaN/GaN HEMTs. All our findings are consistent with the degradation mechanism based on crystallographic-defect formation due to the inverse piezoelectric effects in Ref. [1] (Joh J and del Alamo J A 2006 IEEE IDEM Tech. Digest p. 415). However, under the on-state condition, the devices are suffering from both inverse piezoelectric effects and hot electron effects, and so to improve the reliability of the devices both effects should be taken into consideration.     

Impact of oxygen in electrical properties and hot-carrier stress-induced degradation of GaN high electron mobility transistors

The role of the oxygen in AlGaN/GaN high electron mobility transistors (HEMTs) before and after semi-on state stress was discussed. Comparing with the electrical characteristics of the devices in vacuum, air, and oxygen atmosphere, it is revealed that the oxygen has significant influence on the electric characteristics and the hot-carrier-stress-induced degradation of the device. Comparing with the situation in vacuum, the gate leakage increased an order of magnitude in oxygen and air atmosphere. Double gate structure was used to separate the barrier leakage and surface leakage of AlGaN/GaN HEMT it is found that surface leakage is the major influencing factor in gate leakage of SiN-passivated devices before and after semi-on state stress. During semi-on state stress in the oxygen atmosphere, the electric-field-driven oxidation process promoted the oxidation of the nitride layer, and the oxidation layer in the SiN/AlGaN interface leads to the decreasing of the surface leakage.     

场板结构AlGaN/GaN HEMT的电流崩塌机理

在不同的漏偏压下，研究了钝化和不同场板尺寸AlGaN/GaN HEMT对电流崩塌的抑制能力.实验结果表明，钝化器件对电流崩塌的抑制能力随着漏偏压的升高而显著下降；在高漏偏压下，场板的尺寸对器件抑制崩塌的能力有较大影响，而合适尺寸的场板结构在各个漏偏压下都能够很好的抑制电流崩塌.深入分析发现，场板结构不仅能够抑制虚栅的充电过程，而且提供了放电途径，有利于虚栅的放电，从而抑制电流崩塌.在此基础上，通过建立场板介质对虚栅放电的模型，解释了高漏偏压下场板的尺寸对器件抑制崩塌的能力有较大影响的原因.     

场板结构AlGaN/GaN HEMT的电流崩塌机理

在不同的漏偏压下,研究了钝化和不同场板尺寸AlGaN/GaN HEMT对电流崩塌的抑制能力.实验结果表明,钝化器件对电流崩塌的抑制能力随着漏偏压的升高而显著下降;在高漏偏压下,场板的尺寸对器件抑制崩塌的能力有较大影响,而合适尺寸的场板结构在各个漏偏压下都能够很好的抑制电流崩塌.深入分析发现,场板结构不仅能够抑制虚栅的充电过程,而且提供了放电途径,有利于虚栅的放电,从而抑制电流崩塌.在此基础上,通过建立场板介质对虚栅放电的模型,解释了高漏偏压下场板的尺寸对器件抑制崩塌的能力有较大影响的原因. 关键词： AlGaN/GaN HEMT 场板 电流崩塌     

AlGaN表面坑状缺陷及GaN缓冲层位错缺陷对AlGaN/GaN HEMT电流崩塌效应的影响

利用金属有机气相外延(MOVPE)技术生长了具有不同AlGaN表面坑状缺陷和GaN缓冲层位错缺陷密度的AlGaN/GaN 高电子迁移率晶体管(HEMT)样品,并对比研究了两种缺陷对器件栅、漏延迟电流崩塌效应的影响.栅延迟测试表明,AlGaN表面坑状缺陷会引起栅延迟电流崩塌效应和源漏电阻的增加,而且表面坑状缺陷越多,栅延迟电流崩塌程度和源漏电阻的增加越明显.漏延迟测试显示,AlGaN表面坑状缺陷对漏延迟电流崩塌影响不大,而GaN缓冲层位错缺陷主要影响漏延迟电流崩塌.研究结果表明,AlGaN表面坑状缺陷和Ga 关键词： AlGaN/GaN HEMT 电流崩塌 坑状缺陷 位错缺陷     

AlGaN/GaN high-electron-mobility transistors with transparent gates by Al-doped ZnO

AlGaN/GaN high-electron-mobility transistors （HEMTs） with Al-doped ZnO （AZO） transparent gate electrodes are fabricated, and Ni/Au/Ni-gated HEMTs are produced in comparison. The AZO-gated HEMTs show good DC characteristics and Schottky rectifying characteristics, and the gate electrodes achieve excellent transparencies. Compared with Ni/Au/Ni-gated HEMTs, AZO-gated HEMTs show a low saturation current, high threshold voltage, high Schottky barrier height, and low gate reverse leakage current. Due to the higher gate resistivity, AZO-gated HEMTs exhibit a current-gain cutoff frequency （fT） of 10 GHz and a power gain cutoff frequency （fmax） of 5 GHz, and lower maximum oscillation frequency than Ni/Au/Ni-gated HEMTs. Moreover, the C-V characteristics are measured and the gate interface characteristics of the AZO-gated devices are investigated by a C-V dual sweep.     

基于脉冲方法的超短栅长GaN基高电子迁移率晶体管陷阱效应机理

陷阱效应导致的电流崩塌是制约GaN基微波功率电子器件性能提高的一个重要因素,研究深能级陷阱行为对材料生长和器件开发具有非常重要的意义.随着器件频率的提升,器件尺寸不断缩小,对小尺寸器件中深能级陷阱的表征变得越发困难.本文制备了超短栅长（L_g=80 nm）的AlGaN/GaN金属氧化物半导体高电子迁移率晶体管（MOSHEMT）,并基于脉冲I-V测试和二维数值瞬态仿真对器件的动态特性进行了深入研究,分析了深能级陷阱对AlGaN/GaN MOSHEMT器件动态特性的影响以及相关陷阱效应的内在物理机制.结果表明,AlGaN/GaN MOSHEMT器件的电流崩塌随着栅极静态偏置电压的增加呈非单调变化趋势,这是由栅漏电注入和热电子注入两种陷阱机制共同作用的结果.根据研究结果推断,可通过改善栅介质的质量以减小栅漏电或提高外延材料质量以减少缺陷密度等措施达到抑制陷阱效应的目的,从而进一步抑制电流崩塌.     

Time-dependent degradation of threshold voltage in AlGaN/GaN high electron mobility transistors

This paper gives a detailed analysis of the time-dependent degradation of the threshold voltage in AlGaN/GaN high electron mobility transistors(HEMTs) submitted to off-state stress. The threshold voltage shows a positive shift in the early stress, then turns to a negative shift. The negative shift of the threshold voltage seems to have a long recovery time. A model related with the balance of electron trapping and detrapping induced by shallow donors and deep acceptors is proposed to explain this degradation mode.     

Simulation design of normally-off AlGaN/GaN high-electron-mobility transistors with p-GaN Schottky hybrid gate

A novel normally-off AlGaN/GaN high-electron-mobility transistor (HEMT) with a p-GaN Schottky hybrid gate (PSHG) is proposed, and compared with the conventional p-GaN normally-off AlGaN/GaN HEMTs. This structure can be realized by selective etching of p-GaN layer, which enables the Schottky junction and PN junction to control the channel charge at the same time. The direct current (DC) and switching characteristics of the PSHG HEMTs are simulated by Slivaco TCAD, and the p-GaN HEMTs and conventional normally-on HEMTs are also simulated for comparison. The simulation results show that the PSHG HEMTs have a higher current density and a lower on-resistance than p-GaN HEMTs, which is more obvious with the decrease of p-GaN ratios of the PSHG HEMTs. The breakdown voltage and threshold voltage of the PSHG HEMTs are very close to those of the p-GaN HEMTs. In addition, the PSHG HEMTs have a higher switching speed than the conventional normally-on HEMTs, and the p-GaN layer ratio has no obvious effect on the switching speed.