SnO2-coated multiwall carbon nanotube composite anode materials for rechargeable lithium-ion batteries

SnO₂-coated multiwall carbon nanotube (MWCNT) nanocomposites were synthesized by a facile hydrothermal method. The as-prepared nanocomposites were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). The SnO₂/MWCNT composites, when combined with carboxymethyl cellulose (CMC) as a binder, show excellent cyclic retention, with the high specific capacity of 473 mAh g⁻¹ beyond 100 cycles, much greater than that of the bare SnO₂ which was also prepared by the hydrothermal method in the absence of MWCNTs. The enhanced capacity retention could be mainly attributed to good dispersion of the tin dioxide particles in the matrix of MWCNTs, which protected the particles from agglomeration during the cycling process. Furthermore, the usage of CMC as a binder is responsible for the low cost and environmental friendliness of the whole electrode fabrication process.     

High reversible capacity of SnO2/graphene nanocomposite as an anode material for lithium-ion batteries

A gas–liquid interfacial synthesis approach has been developed to prepare SnO₂/graphene nanocomposite. The as-prepared nanocomposite was characterized by X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, and Brunauer–Emmett–Teller measurements. Field emission scanning electron microscopy and transmission electron microscopy observation revealed the homogeneous distribution of SnO₂ nanoparticles (2–6 nm in size) on graphene matrix. The electrochemical performances were evaluated by using coin-type cells versus metallic lithium. The SnO₂/graphene nanocomposite prepared by the gas–liquid interface reaction exhibits a high reversible specific capacity of 1304 mAh g⁻¹ at a current density of 100 mA g⁻¹ and excellent rate capability, even at a high current density of 1000 mA g⁻¹, the reversible capacity was still as high as 748 mAh g⁻¹. The electrochemical test results show that the SnO₂/graphene nanocomposite prepared by the gas–liquid interfacial synthesis approach is a promising anode material for lithium-ion batteries.     

Ultrafine SnO2 nanoparticles as a high performance anode material for lithium ion battery

In this paper, the ultrafine tin oxides (SnO₂) nanoparticles are fabricated by a facile microwave hydrothermal method with the mean size of only 14 nm. Phase compositions and microstructures of the as-prepared nanoparticles have been investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). It was found that the ultrafine SnO₂ nanoparticles are obtained to be the pure rutile-structural phase with the good dispersibility. Galvanostatic cycling and cyclic voltammetry results indicate that the first discharge capacity of the ultrafine SnO₂ electrode is 1196.63  mAh g⁻¹, and the reversible capacity could retain 272.63 mAh g⁻¹ at 100 mA g⁻¹ after 50 cycles for lithium ion batteries (LIBs). The excellent electrochemical performance of the SnO₂ anode for LIBs is attributed to its ultrafine nanostructure for providing active sites during lithium insertion/extraction processes. Pulverization and agglomeration of the active materials are effectively reduced by the microwave hydrothermal method.     

Graphene-supported SnO2 nanoparticles prepared by a solvothermal approach for an enhanced electrochemical performance in lithium-ion batteries

SnO₂ nanoparticles were dispersed on graphene nanosheets through a solvothermal approach using ethylene glycol as the solvent. The uniform distribution of SnO₂ nanoparticles on graphene nanosheets has been confirmed by scanning electron microscopy and transmission electron microscopy. The particle size of SnO₂ was determined to be around 5 nm. The as-synthesized SnO₂/graphene nanocomposite exhibited an enhanced electrochemical performance in lithium-ion batteries, compared with bare graphene nanosheets and bare SnO₂ nanoparticles. The SnO₂/graphene nanocomposite electrode delivered a reversible lithium storage capacity of 830 mAh g⁻¹ and a stable cyclability up to 100 cycles. The excellent electrochemical properties of this graphene-supported nanocomposite could be attributed to the insertion of nanoparticles between graphene nanolayers and the optimized nanoparticles distribution on graphene nanosheets.     

Facile synthesis and superior anodic performance of ultrafine SnO2-containing nanocomposites

Ultrafine SnO₂-containing nanocomposites were synthesized from glucose/SnCl₂ acid solution under hydrothermal environment. The content of SnO₂ in the nanocomposites could be adjusted by changing the mass ratio of SnCl₂ to glucose in the initial solution. The crystalline structure and morphology of the as-synthesized nanocomposites have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM). The results revealed that the nanocomposites were composed of highly dispersing SnO₂ nanoparticles with the sizes of only a few nanometers (3–5 nm). Electrochemical tests demonstrated that the electrochemical performances were strongly dependent on the content of SnO₂ in the nanocomposites. The nanocomposites containing 75 wt.% SnO₂ exhibited an outstanding reversible capacity of 610 mAh/g and high capacity retention after 200 cycles. The extraordinary performance should originate from the very small size of SnO₂ nanoparticles and carbon precursor matrix derived from glucose which can confer the ability to accommodate the volume changes and prevent the agglomeration of Sn particles during charge/discharge process.     

Facile preparation of Bi nanoparticles by novel cathodic dispersion of bulk bismuth electrodes

A novel electrochemical approach has been developed to prepare clean bismuth nanoparticles (NPs) with a bulk Bi electrode in a 0.5 mol dm⁻³ NaOH solution under highly cathodic polarization of −8 V versus a saturated mercurous sulfate electrode, requiring no any precursor ions and organic protective agents. The bulk Bi electrode can be facilely dispersed into Bi NPs at the condition of intensive hydrogen evolution. This cathodic dispersion of the bulk Bi electrode involves the formation and decomposition of unstable bismuth hydrides and the aggregation of atomic bismuth from the decomposition. Moreover, Bi₂O₃ NPs have also been achieved by heating the precursor Bi NPs. Field-emission scanning electron microscopy, transmission electron microscope and X-ray diffraction were used to characterize these NPs. The as-prepared Bi NPs mainly existed in rhombohedral phase.     

Hydrothermally prepared nanocrystalline Mn–Zn ferrites: Synthesis and characterization

Nanocrystalline particles of Mn_xZn_1−xFe₂O₄ were prepared by chemical precipitation of hydroxides, followed by hydrothermal processing and freeze–drying. The synthesis involves the hydrolysis of aqueous metal precursors by using ammonia as precipitating agent. The chlorine ion concentration in the solution and the pH of the precipitation, are shown to play a crucial role in retaining the initial stoichiometry of the solution to the nanoparticles. The obtained products exhibited some interesting and unique features: they consisted of nanoparticles with sizes ranging from 5 to 25 nm, they had surface areas between 60 and 110 m² g⁻¹ and pore sizes in the mesopore region (i.e. 8–20 nm). The produced materials were examined by powder X-ray diffraction for crystalline phase identification, scanning electron microscopy for grain morphology, high resolution transmission electron microscopy for particle size distribution and nitrogen sorption for surface area, pore volume and pore size distribution determination. The sintering of the ferrite powders was also studied by thermogravimetric analysis and dilatometry of the powders mixed with an organic binder to improve their compaction properties.     

Synthesis of uniform polycrystalline tin dioxide nanofibers and electrochemical application in lithium-ion batteries

Under optimized synthesis conditions, very large area uniform SnO₂ nanofibers consisting of orderly bonded nanoparticles have been obtained for the first time by thermal pyrolysis and oxidization of electrospun tin(II)2-ethylhexanoate/polyacrylonitrile (PAN) polymer nanofibers in air. The structure and morphology were elaborated by X-ray diffraction (XRD), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The SnO₂ nanofibers delivered a reversible capacity of 446 mAh g⁻¹ after 50 cycles at the 100 mA g⁻¹ rate and excellent rate capability of 477.7 mAh g⁻¹ at 10.0 C. Owing to the improved electrochemical performance, this electrospun SnO₂ nanofiber could be one of the most promising candidate anode materials for the lithium-ion battery.     

Preparation and electrochemical performance of micro-nanostructured nickel

Micro-nanostructured nickel has been prepared as anode materials for Li ion batteries, via a rheological phase reaction method. Ni₂C₂O₄·xH₂O (x = 2 or 2.5) as precursors are obtained from the solid–liquid rheological mixture of (NH4)₂C₂O₄·H₂O and Ni(NO₃)₂. The nickel powders are prepared by thermal decomposition of the precursors. The structural, morphological and electrochemical performance are investigated by means of thermogravimetry (TG), differential scanning calorimetry (DSC), powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM) and typical electrochemical tests. The micro-nanostructured nickel displays an initial discharge capacity of 457 mAh g⁻¹. It also has a remarkable cycling stability with an average capacity fade of 0.17% per cycle from 13th to 50th cycle in 0.01–3.00 V versus Li at a constant current density of 100 mA g⁻¹.     

Nonaqueous and template-free synthesis of Sb doped SnO2 microspheres and their application to lithium-ion battery anode

Antimony doped SnO₂ (ATO) microspheres composed of ATO nanoparticles were prepared by using a hydrothermal process in a nonaqueous and template-free solution from the inorganic precursors (SnCl₄ and Sb(OC₂H₅)₃). The physical properties of the as-synthesized samples were investigated by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), N₂ adsorption-desorption isotherms, and X-ray photoelectron spectrum (XPS). The resulting particles were highly crystalline ATO microspheres in the diameter range of 3-10 μm and with many pores. The as-prepared samples were used as negative materials for lithium-ion battery, whose charge-discharge properties, cyclic voltammetry, and cycle performance were examined. The results showed that a high initial discharge capacity of 1981 mAh g⁻¹ and a charge capacity of 957 mAh g⁻¹ in a potential range of 0.005-3.0 V was achieved, which suggests that tin oxide-based materials work as high capacity anodes for lithium-ion rechargeable batteries. The cycle performance is improved because the conducting ATO nanoparticles can also perform as a better matrix for lithium-ion battery anode.     

Free-standing single-walled carbon nanotube/SnO2 anode paper for flexible lithium-ion batteries

Free-standing single-walled carbon nanotube/SnO₂ (SWCNT/SnO₂) anode paper was prepared by vacuum filtration of SWCNT/SnO₂ hybrid material which was synthesized by the polyol method. From field emission scanning electron microscopy and transmission electron microscopy, the CNTs form a three-dimensional nanoporous network, in which ultra-fine SnO₂ nanoparticles, which had crystallite sizes of less than 5 nm, were distributed, predominately as groups of nanoparticles on the surfaces of single walled CNT bundles. Electrochemical measurements demonstrated that the anode paper with 34 wt.% SnO₂ had excellent cyclic retention, with the high specific capacity of 454 mAh g^?1 beyond 100 cycles at a current density of 25 mA g^?1, much higher than that of the corresponding pristine CNT paper. The SWCNTs could act as a flexible mechanical support for strain release, offering an efficient electrically conducting channel, while the nanosized SnO₂ provides the high capacity. The SWCNT/SnO₂ flexible electrodes can be bent to extremely small radii of curvature and still function well, despite a marginal decrease in the conductivity of the cell. The electrochemical response is maintained in the initial and further cycling process. Such capabilities demonstrate that this model hold great promise for applications requiring flexible and bendable Li-ion batteries.     

Synthesis and characterization of microspheres composed of SnO2 nanoparticles processed via a chemical route

SnO₂ microspheres were synthesized by a chemical route, heating the mixed Sn²⁺ and sulfuric acid solution in the presence of pressurized oxygen at 900 °C in a designed calorimetric pump. Phase analysis was carried out by X-ray diffraction (XRD) and the results confirmed the SnO₂ microspheres as a single-phase tetragonal structure. Scanning electron microscopy (SEM) images indicated that these microspheres with average diameters of 0.9 μm were composed of SnO₂ nanoparticles with a diameter of about 4.7 nm and a crystallite size of 3.7 nm, as observed by transmission electron microscope (TEM) and calculated by Scherrer's equation from diffractograms, respectively. The formation mechanism of microspheres composed of SnO₂ nanoparticles and the influence of changes in processing are proposed and explained.     

Preparation and electrochemical performance of SnO2@carbon nanotube core–shell structure composites as anode material for lithium-ion batteries

Carbon nanotube-encapsulated SnO₂ (SnO₂@CNT) core–shell composite anode materials are prepared by chemical activation of carbon nanotubes (CNTs) and wet chemical filling. The results of X-ray diffraction and transmission electron microscopy measurements indicate that SnO₂ is filled into the interior hollow core of CNTs and exists as small nanoparticles with diameter of about 6 nm. The SnO₂@CNT composites exhibit enhanced electrochemical performance at various current densities when used as the anode material for lithium-ion batteries. At 0.2 mA cm^?2 (0.1C), the sample containing wt. 65% of SnO₂ displays a reversible specific capacity of 829.5 mAh g^?1 and maintains 627.8 mAh g^?1 after 50 cycles. When the current density is 1.0, 2.0, and 4.0 mA cm^?2 (about 0.5, 1.0, and 2.0C), the composite electrode still exhibits capacity retention of 563, 507 and 380 mAh g^?1, respectively. The capacity retention of our SnO₂@CNT composites is much higher than previously reported values for a SnO₂/CNT composite with the same filling yield. The excellent lithium storage and rate capacity performance of SnO₂@CNT core–shell composites make it a promising anode material for lithium-ion batteries.     

The role of particle size on the electrochemical properties at 25 and at 55 °C of the LiCr0.2Ni0.4Mn1.4O4 spinel as 5 V-cathode materials for lithium-ion batteries

The role of the particle size on the electrochemical properties at 25 and at 55 °C of the LiCr_0.2Ni_0.4Mn_1.4O₄ spinel synthesized by combustion method has been determined. Samples with different particle size were obtained by heating the raw spinel from 700 to 1100 °C, for 1 h in air. X-ray diffraction patterns revealed that all the prepared materials are single-phase spinels. The main effect of the thermal treatment is the remarkable increase of the particles size from 60 to 3000 nm as determined by transmission electron microscopy. The electrochemical properties were determined at high discharge currents (1C rate) in two-electrode Li-cells. At 25 and at 55 °C, in spite of the great differences in particle size, the discharge capacity drained by all samples is similar (Q_dch ≈ 135 mAh g⁻¹). Instead, the cycling performances strongly change with the particle size. The spinels with Φ > 500 nm show better cycling stability at 25 and at 55 °C than those with Φ < 500 nm. The samples heated at 1000 and 1100 °C, with high potential (E ≈ 4.7 V), elevate capacity (Q ≈ 135 mAh g⁻¹), and remarkable cycling performances (capacity retention after 250 cycles >96%) are very attractive materials as 5V-cathodes for high-energy Li-ion batteries.     

Carbon incorporation and deactivation of MgO(0 0 1) supported Pd nanoparticles during CO oxidation

We have investigated the structure and composition of the model catalyst system Pd/MgO(0 0 1) during oxidation, CO reduction and CO oxidation at near atmospheric pressures by a combination of in situ X-ray diffraction and ex situ transmission electron microscopy and spectroscopy techniques. From the in situ X-ray experiments, we find: (a) the Pd nanoparticles with 9 nm in diameter transform into epitaxial PdO above 10⁻¹ mbar O₂ pressure at 570 K, (b) the oxidation process can be reverted by CO exposure, recovering Pd nanoparticles in their initial orientation, and (c) during CO oxidation in a mixture of 50 mbar O₂ and 50 mbar CO a new phase is evolving with lattice constant close to the MgO substrate value, which we assign to expanded Pd nanoparticles forming upon carbon incorporation. Ex situ transmission electron microscopy and different spectroscopy techniques uncover the CO₂ induced growth of a disordered overlayer containing C, Mg and O, which forms during CO oxidation and leads to an overgrowth of Pd nanoparticles thereby deactivating the catalyst.     

The investigation on electrochemical reaction mechanism of CuF2 thin film with lithium

Crystalline CuF₂ thin films were prepared by pulsed laser deposition under room temperature. The physical and electrochemical properties of the as-deposited thin films have been investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), galvanostatic cycling and cyclic voltammetry (CV). Reversible capacity of 544 mAh g⁻¹ was achieved in the potential range of 1.0–4.0 V. A reversible couple of redox peaks at 3.0 V and 3.7 V was firstly observed. By using ex situ XRD and TEM techniques, an insertion process followed by a fully conversion reaction to Cu and LiF was revealed in the lithium electrochemical reaction of CuF₂ thin film electrode. The reversible insertion reaction above 2.8 V could provide a capacity of about 125 mAh g⁻¹, which makes CuF₂ a potential cathode material for rechargeable lithium batteries.     

Enhanced cycling performance of Fe3O4-graphene nanocomposite as an anode material for lithium-ion batteries

Fe₃O₄-graphene nanocomposite was prepared by a gas/liquid interface reaction. The structure and morphology of the Fe₃O₄-graphene nanocomposite were characterized by X-ray diffraction, scanning electron microscopy and high-resolution transmission electron microscopy. The electrochemical performances were evaluated in coin-type cells. Electrochemical tests show that the Fe₃O₄-22.7 wt.% graphene nanocomposite exhibits much higher capacity retention with a large reversible specific capacity of 1048 mAh g⁻¹ (99% of the initial reversible specific capacity) at the 90th cycle in comparison with that of the bare Fe₃O₄ nanoparticles (only 226 mAh g⁻¹ at the 34th cycle). The enhanced cycling performance can be attributed to the facts that the graphene sheets distributed between the Fe₃O₄ nanoparticles can prevent the aggregation of the Fe₃O₄ nanoparticles, and the Fe₃O₄-graphene nanocomposite can provide buffering spaces against the volume changes of Fe₃O₄ nanoparticles during electrochemical cycling.     

The synthesis of Li(Ni1/3Co1/3Mn1/3)O2 using eutectic mixed lithium salt LiNO3–LiOH

A lithium-ion battery cathode material, Li(Ni_1/3Co_1/3Mn_1/3)O₂, with excellent electrochemical properties was prepared via two-step isothermal sintering, using eutectic lithium salts (0.38LiOH·H₂O–0.62LiNO₃) mixed with Co, Ni, or Mn hydroxides. Based on analysis using X-ray diffraction (XRD), scanning electron microscopy (SEM), a thermogravimetric-differential scanning calorimetric (TG–DSC) analyzer, and Fourier-transform Infrared (FT-IR), this synthetic process consists of procedures including lithium salt melting, permeation, reaction, crystalline transformation, and crystallization. Due to the lower melting point of the eutectic molten salts compared with that of the single lithium salt, a relatively mild synthetic condition (low temperature) is needed, and the product can be highly crystallized with low cation mixing, which facilitates maintenance of the precursor morphology. The electrochemical properties of the product were investigated by constant current discharge–charge and cyclic voltammetry. The results show that the initial discharge capacity is 160 mhA g⁻¹, with excellent cycling stability even after 50 cycles. We conclude that this novel eutectic molten salt method is a promising and practical approach for synthesizing cathode materials for lithium-ion batteries.     

Controllable synthesis of CaTi2O4(OH)2 nanoflakes by a facile template-free process and its properties

Serrated leaf-like CaTi₂O₄(OH)₂ nanoflake crystals were synthesized via a template-free and surfactant-free hydrothermal process. The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM). The growth process for CaTi₂O₄(OH)₂ nanoflakes was dominated by a crystallization–dissolution–recrystallization growth mechanism. BET analysis showed that CaTi₂O₄(OH)₂ nanoflakes had mesoporous structure with an average pore size of 8.7 nm, and a large surface area of 88.4 m² g⁻¹. Cyclic voltammetry and galvanostatic charge–discharge tests revealed that the electrode synthesized from CaTi₂O₄(OH)₂ nanoflakes reached specific capacitances of 162 F g⁻¹ at the discharge current of 2 mA cm⁻², and also exhibited excellent electrochemical stability.     

Electrochemical energy storage performance of heterostructured SnO2@MnO2 nanoflakes

In this work, we report synthesis of SnO₂@MnO₂ nanoflakes grown on nickel foam through a facile two-step hydrothermal route. The as-obtained products are characterized by series of techniques such as scanning electron microscopy (SEM), X-ray diffraction spectroscopy (XRD), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). The as-obtained SnO₂@MnO₂ nanoflakes are directly used as supercapacitor electrode materials. The results show that the electrode possesses a high discharge areal capacitance of 1231.6 mF cm⁻² at 1 mA cm⁻² and benign cycling stability with 67.2% of initial areal capacitance retention when the current density is 10 mA cm⁻² after 6000 cycles. Moreover, the heterostructured electrode shows 41.1% retention of the initial capacitance when the current densities change from 1 to 10 mA cm⁻², which reveals good rate capability. SnO₂@MnO₂ nanoflakes products which possess excellent electrochemical properties might be used as potential electrode materials for supercapacitor applications.