万古霉素键合手性固定相高效液相色谱法直接分离泰妥拉唑对映体

利用反相高效液相色谱法在大环抗生素类手性固定相万古霉素键合手性固定相(Chirobiotic V)上直接分离了泰妥拉唑对映体。考察了缓冲溶液的种类、浓度和pH值,有机改性剂的种类和浓度,柱长和柱温等对手性分离的影响。优化后的色谱条件为:Chirobiotic V色谱柱(150 mm×4.6 mm,5 μm),流动相为0.02 mol/L 醋酸铵缓冲液(pH 6.0)-四氢呋喃(体积比为93∶7),流速为0.5 mL/min,柱温为20 ℃,检测波长为306 nm。在此条件下泰妥拉唑对映体达到了基线分离,分离度达1.68;对映体保留时间的相对标准偏差分别为0.48%和0.49%(n=6),峰面积的相对标准偏差分别为0.45%和0.55%(n=6)。所建立的手性分离方法具有简便快速及重复性好等优点。     

C18柱串联冠醚手性柱高效分离3种芳香族氨基酸对映体

将C18柱与手性冠醚柱串联,建立了一种反相高效液相色谱法用于3种芳香族氨基酸对映体同时拆分的方法.考察了反相色谱流动相的组成、pH值、柱温、流速对对映体拆分的影响.实验结果表明,当流动相为HClO4-乙睛溶液(86:14,V/V,pH 2.0)、柱温20℃、流速0.4 mL/min时,3种氨基酸对映体可获得基线分离.进一步对比了C18柱、冠醚手性柱和串联顺序不同的4种分离模式,结果表明,C18柱不能拆分氨基酸对映体,仅能分离不同种类氨基酸;冠醚手性柱可分离氨基酸映体,但不同种类氨基酸色谱峰出现重叠;串联模式能实现3种氨基酸对映体的基线分离,实现双柱优势互补,而串联顺序对分离影响不大,仅影响色谱峰的峰形.     

手性流动相HPLC法拆分对羟基苯甘氨酸对映体的研究

将β-环糊精、羟丙基-β-环糊精作为手性流动相添加剂,系统地研究了D,L对羟基苯甘氨酸在RP-HPLC系统中的拆分。分别考察了手性流动相的种类,手性试剂β-环糊精的浓度,流动相的pH,修饰剂的种类及浓度,色谱柱温度等对拆分效果的影响,以-βCD为手性流动相添加剂,建立了-βCD手性流动相分离对羟基苯甘氨酸对映体的方法。结果表明:用ODS柱(250 mm×4.6 mmi.d.),以V(甲醇-β环糊精)∶V(pH 4.5磷酸盐缓冲液)=30∶70为流动相,流速0.2 mL/min,柱温25℃,检测波长为230 nm时对羟基苯甘氨酸对映体得到了良好的基线分离,分离度可达1.71。     

α1-酸性糖蛋白柱拆分马来酸曲美布汀对映体

以α1-AGP为固定相,建立了马来酸曲美布汀的HPLC对映体拆分方法.考察了流动相pH、缓冲盐溶液的浓度、有机改性剂种类和浓度、流速、柱温等对对映体分离的影响.优化后的色谱条件为Chiral-AGP(100 mm×4.0 mm,5 μm)色谱柱,流动相为10 mmol/L醋酸铵缓冲液(pH 3.8);流速为0.4 mL/min;柱温为35℃.马来酸曲美布汀对映体的保留时间分别为7.4 min和9.8 min;分离度为1.59.     

手性流动相添加剂法拆分比索洛尔对映体

以羧甲基-β-环糊精作为手性流动相添加剂,建立了高效液相色谱拆分比索洛尔对映体的方法。系统考察了手性添加剂的种类及浓度、流动相中甲醇的含量、pH值和流速等因素对拆分的影响。色谱分离条件:流动相甲醇∶乙腈∶水为20∶67∶13(V/V/V),羧甲基-β-环糊精浓度为0.5g.L-1,pH值为4.07(以三乙胺-冰乙酸调节),流速为0.3mL.min-1,检测波长223nm,对映体得到基线分离,分离度为1.89。     

手性流动相添加剂法拆分安妥沙星对映体

采用L-苯丙氨酸和CuSO_4作为手性流动相添加剂,建立液相色谱法拆分安妥沙星对映体的方法。考察了手性添加剂的种类、浓度及流动相pH等对安妥沙星对映体分离的影响。采用Welch Ultimate XBC_(18)色谱柱(4.6 mm×250 mm,5μm),优化流动相为8 mmol/L L-苯丙氨酸溶液(含4 mmol/L的CuSO_4,pH 3.5)-甲醇(80∶20,V∶V),流速:1.0 mL/min,检测波长:302 nm,结果左、右旋安妥沙星峰达到基线分离,分离度为6.6。     

高效液相色谱手性流动相添加剂分离西孟坦对映体

以 β 环糊精作为手性流动相添加剂 ,研究了DL 西孟坦在反相HPLC系统中的拆分。考察了缓冲盐的浓度、pH、β 环糊精的浓度、流动相中甲醇的比例、流动相流速和温度对手性分离的影响 ,建立了 β 环糊精动态手性固定相法分离西孟坦对映体的方法。色谱条件为 :ZirchromKromasilODS 1(5 μm ,15 0mm× 4 .6mm)色谱柱 ,流动相为 2 0mmol/L磷酸盐缓冲液 (pH 6 .0 )含 12mmol/Lβ 环糊精∶甲醇 (70∶30 ,V/V) ,流速为 0 .8mL/min ,温度为 17℃。DL 西孟坦对映体的保留时间分别为 2 2 .5和 2 4 .5min ,分离度为 1.5 7。     

直链淀粉手性固定相分离马来酸曲美布汀和昂丹司琼对映体

建立了马来酸曲美布汀和昂丹司琼对映体的高效液相色谱拆分方法。使用Chiralpak AD-H手性色谱柱,采用正相洗脱方式,考察了流动相中有机改性剂的种类和浓度、酸碱比(冰乙酸-三乙胺)、柱温及流速等因素对对映体拆分的影响。确定了最佳拆分条件:分离马来酸曲美布汀的流动相为正己烷-异丙醇-冰乙酸-三乙胺(97∶3∶0.1∶0.3),流速为0.6mL/min;分离昂丹司琼的流动相为正己烷-异丙醇-冰乙酸-三乙胺(70∶30∶0.2∶0.4),流速为0.4mL/min,柱温均为20℃。在上述色谱条件下,两种手性药物对映体达到基线分离。     

高效液相色谱手性流动相添加法拆分阿卓乳酸对映体

采用C₁₈反相色谱柱,以磺丁基醚-β-环糊精（SBE-β-CD）作为手性流动相添加剂,建立了阿卓乳酸对映体的高效液相色谱拆分方法。考察了环糊精衍生物类型、手性添加剂浓度、流动相pH、流速和柱温对手性分离的影响,同时探讨了高效液相色谱采用磺丁基醚-β-环糊精分离阿卓乳酸对映体的分离机制及包结常数,确定了色谱条件为YMC-Pack ODS-A C₁₈色谱柱（250 mm×4.6 mm,5 μm）,流动相为含25 mmol/LSBE-β-CD的0.1 mol/L磷酸盐缓冲液（pH 2.68）-乙腈（90：10,v/v）,流速为0.6 mL/min,柱温为30 ℃,紫外检测波长为220 nm。对映体的保留时间分别为26.65和28.28 min,分离度为1.68。本方法分离度好,简便易行,且比使用手性固定相分离更加经济。     

磺丁基醚-β-环糊精手性流动相添加剂法拆分佐匹克隆对映体

采用磺丁基醚-β-环糊精(SBE-β-CD)为手性流动相添加剂,建立了反相高效液相色谱手性流动相添加剂法拆分分离佐匹克隆对映体的方法。在普通C18色谱柱(250 mm×4.6 mm×5.0μm)上,考察了水相pH、磺丁基醚-β-环糊精浓度、磷酸盐缓冲液浓度、甲醇含量、柱温等对佐匹克隆对映体拆分效果的影响。确定最适用的色谱条件:流动相为水相(5 mmol/L NaH2PO4,含磺丁基醚-β-环糊精5 mmo/L,以H3PO4调pH为3):甲醇=78:22(V/V),检测波长305nm,流速为1 mL/min,柱温为30℃,此条件下佐匹克隆对映体的保留时间分别为23.0和25.6 min,分离度为1.81。两对对映体质量浓度在0.04~0.36g/L范围内线性关系良好(r≥0.9990),保留时间的RSD分别为0.73%和0.80%,峰面积的RSD分别为1.2%和1.1%。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.