运算放大器的新进展—电流反馈型放大器

本文介绍了一种新型的运算放大器－电流反馈型放大器的特性，原理和应用，这种运算放大器的增益－带宽和摆率显著高于一般运算放大器，并且它的频带，摆率建立时间基本上和闭环增益无关，它可用于通讯，雷达，仪器等各个领域，本文给出了应用实例和电流反馈型放大器性能一览表。     

高速运算放大器新技术——电流反馈运算放大器

简述了高速运算放大器的进展，着重描述了８０年代末期基于互补双极工艺发展起来的电流反馈运算放大器的原理，特点，应用及制造工艺，分析了电流反馈运算放大器的小信号特性和大信号特性。     

电流反馈运算放大器与电压反馈运算放大器的区别与应用

本文介绍了电流反馈运算放大器与电压反馈运算放大器的区别及其有关的增益表达式，并且列举了几个应用实例，说明如何选用运算放大器。     

电流反馈运算放大器的特点

一种新型的高频运算放大器——电流反馈运算放大器,又称互阻抗运算放大器,最近很流行。本文不讨论其广为流行的理由,仅讨论在一定的条件下它比传统的电压反馈运算放大器具有优良的高频性能。 电流反馈运算放大器的等效电路图如图1所示。像电压反馈运算放大器一样,电流反馈运算放大器也有反     

一种电压反馈型高速宽带运算放大器的设计

介绍了一种融合电流映射传输方式的电压反馈型高速宽带运算放大器的工作特性。结合高速宽带运算放大器工作原理,对设计思路进行分析。研究了影响高速宽带运算放大器特性的相关因素,讨论了优化运算放大器动态性能的部分措施。在相关分析的基础上,结合亚微米高速双极工艺,对电路的特性参数进行了仿真设计。     

一种超高速宽带运算放大器的设计北大核心

介绍了一种采用高速双极工艺研制的超高速宽带运算放大器电路。运算放大器内部采用高速电流反馈结构进行信号传输和放大,通过带宽提升、电压/电流信号转换以及稳定性补偿等设计技术,获得了要求的速度和带宽。研究了高速宽带运放性能的影响因素,并结合高速双极工艺进行了电路仿真设计和流片制作。测试结果表明:在±5 V电源电压下,运算放大器的电源电流≤6 mA,-3 dB带宽≥500 MHz,转换速率≥1 500 V/μs。     

集成电流反馈运算放大器的特性及应用设计

介绍电流反馈运算放大器包括电路组成，工作原理及有关的应用设计。     

一种CMOS电流型运算放大器

本文描述一种全差动输入、差动输出的电流型运算放大器（ＣＯＡ）。该放大器采用三个第二代电流转换器（ＣＣＩＩ）作为基本单元部件。在全对称电流型反馈放大器中能提供恒定的增益－带宽乘积或者在互阻抗反馈放大器中提供恒定带宽。该放大器的增益－带宽乘积为３ＭＨｚ，失调电流为０．８μＡ（信号范围±７００μＡ），理论上转换速率极大。此放大器采用２．４μｍ标准ＣＭＯＳ工艺实现。     

新型电流反馈放大器的特点及应用

电流反馈运算放大器CFOA是近几年才推出的新型器件。与电压反馈运算放大器VFOA相比,CFOA具有更宽的带宽和更高的转换速率。如电压运算放大器OP27的转换速率SR＝2.8V／μs,增益带宽积为8MHz。电流反馈放大器EL2020最小的转换速率SR＝500V／μs,带宽为50MHz并且与闭环增益无关。输出电流可达+33mA。新型运算放大器要能够进行电流反馈,运算放大器的设计就要使其中一个输入端为低阻抗。考虑到通常的输入信号为电压信号,另一个输入端设计有一个放大倍数为1的电压缓冲器,输入信号电压接到电压缓冲器上,使该运算放大器能被电压驱…     

电压反馈和电流反馈运算放大器的比较

从闭环特性、开环特性、输入级、噪声等几个方面，对电流反馈(CFB)放大器和电压反馈(VFB)放大器进行了详细的比较，得出了CFB放大器和VFB放大器的一些基本特性和应用场合。通过对这两种电路的比较，有助于电路设计师在实际应用中选择最适合自己要求的运算放大器。     

Realization of nth-order series impedance function using only (n-1) current-feedback amplifiers

A new configuration for realizing a higher-order series impedance function using current-feedback amplifiers (CFAs) is presented. The nth-order series impedance function employs only (n–1) CFAs and (2n–1) passive elements. The higher order series impedance function can be applied to realize various higher-order highpass and lowpass filters. The passive element values can be easily decided from the coefficients of the filter transfer functions. The use of CFAs simplifies the circuit implementation and makes the proposed circuit attractive for application. Experiments and simulation results are given to confirm the theoretical analysis.     

冷阴极正交场放大管作用空间设计与工作点选择

本文从冷阴极启动角度出发,综合回轰阴极产生的二次电子平均速度与慢波结构上传输的慢电磁波相速同步条件,获得正交场器件的磁场强度与频率的关系.探讨了慢波结构的节距相位移与互作用空间尺寸以及阳极电压间的关系,提出了该类管型互作用空间以及确定工作点的工程设计方法.     

Analysis and design of LC amplifiers and LC oscillators using current-feedback amplifiers

The present paper discusses specific types of LC amplifier and LC oscillator using a current-feedback amplifier (CFA). The main advantage of the CFAs versus voltage-feedback amplifiers (VFAs) is their gain-bandwidth independence. Some of the monolithic CFAs provide an additional pin between the first stage (current-controlled current source) and the second stage (voltage follower), where the resistance is very high. This allows a parallel resonance LC tank to be connected to the additional op amp correction pin. The main advantage of this new configurations is the insignificant influence of the load over the parameters of the circuit (voltage gain, Q-factor, etc.). Some recommendations for designing this kind of analogue circuit are given, based on simulation results, symbol analysis of the transfer function and physical experiments as well as elements’ values calculation using centre frequency, voltage gain, bandwidth and Q-factor of the LC amplifiers as input parameters.     

用改进的遗传算法对多信道FRA泵浦源进行优化设计

Based on the nonlinear power coupled equations of fiber Raman amplifiers （FRA）, the optimal design to the pumps source has been done with modified genetic arithmetic in this paper. The numerical simulation shows that, for a 40 channels DWDM system and with three pump sources, the Raman gain of about 10dB can be obtained, and the gain ripple is about 1.5dB. The result is useful for the design of backward-pump FRA.     

Applications of the current feedback operational amplifiers

The current feedback operational amplifiers (CFOAs) are receiving increasing attention as basic building blocks in analog circuit design. This paper gives an overview of the applications of the CFOAs, in particular several new circuits employing the CFOA as the active element are given. These circuits include differential voltage amplifiers, differential integrators, nonideal and ideal inductors, frequency dependent negative resistors and filters. The advantages of using the CFOAs in realizing low sensitivity universal filters with grounded elements will be demonstrated by several new circuits suitable for VLSI implementation. PSPICE simulations using the AD844-CFOA which indicate the frequency limitations of some of the proposed circuits are included.     

S—波段光纤放大器及其研究进展

介绍了实现S-波段放大的3种光纤放大器；掺铥光纤放大器（TDFA）、增益位移TDFA（GSTD-FA）和光纤喇曼放大器，就其原理、结构、特点和发展现状进行了综述。     

Multiple-loop feedback filters using current feedback amplifiers

Novel high-order filter topologies realised by employing current feedback operational amplifiers as active elements are introduced in this article. These are constructed from multiple-loop feedback paths and could be utilised for the realisation of filters of arbitrary order and type. An offered benefit is the requirement for employing only grounded capacitors and resistors. Two design examples are provided and the correct operation of the corresponding topologies has been evaluated through experimental results.     

Alternative Realizations of CMOS Current Feedback Amplifiers for Low Voltage Applications

Two variants of a new current feedback amplifier (CFA) are presented in this paper. These CFAs are realized in CMOS technology and both are capable of working at low voltages. It is shown that one circuit performs better than the other by virtue of an increased impedance at its Z terminal achieved through the use of additional transistors. Analysis of both variants of the current conveyor and buffer that form the current feedback amplifier gives an insight into the location of primary poles and zeros of the CFAs. Simulation results indicate an overall gain bandwidth product in excess of 59 MHz and 102 MHz for each circuit at a gain of –10 and with a 3.3 V supply. Experimental results from a chip fabricated in a 0.35 m CMOS technology agree closely with the simulation results.     

一种分析掺铒光纤放大器性能的简单方法

掺铒光纤放大器的主要性能是它的饱和增益特性和噪声系数。本文首先用两个经验公式，介绍了一种用于模拟掺铒光纤放大器性能的简单方法，接着给出了一个超定方程组，对这种方法作了进一步的改进，最后分别给出利用改进前后的方法计算所得到的结果，同时对计算结果和测量数据作了比较，比较显示我们的方法有着更高的精度。     

自适应预失真线性化技术新方法

随着移动通信中线性调制方法的出现,功率放大器的线性化已成为一个重要的研究课题。迄今人们已研究出了多种对放大器进行线性化的技术和方法,然而理论分析和计算机仿真及实验结果显示,预失真线性化技术是最理想的对放大器进行线性化的技术。提出了一种预失真线性化技术的新方法,对该方法的组成原理作了较为详心头 地论述了并给出了实验仿真结果。