有机体系中电合成纳米PbTiO3粉体及表征

The precursor PbTi(OCH₂CH₃)_6-y(acac)_y for the mixed oxide PbTiO₃was synthesized by electrochemical dissolution of Lead and Titanium with a 1∶2 electricity quality in ethanol and acetyl-acetone solution. Nano-sized PbTiO₃powder was prepared by drying and calcining the xerogel from a direct sol-gel hydrolyzation of the precursor solution under pH of 8.5. The FTIR, TG-DTA, XRD and TEM were employed to characterize the structure of the precursor and nano-sized PbTiO₃. The results showed that the optimized conditions for the preparation of nano-sized PbTiO₃ were the electrolysis of the Lead plate and Titanium plate at 50 ℃ and 40 ℃ respectively under 0.03mol·dm^-3Bu₄NBr solution. The nano-sized PbTiO₃prepared by electrolysis exhibited a dispersive structure with an average diameter of 10 to 15 nm.     

纳米尖晶石LixMn2O4的制备与电化学性能表征

Nano-spinel Li_xMn₂O₄(0.6 ≤x≤ 1.0) was synthesized by two steps of coprecipitation and calcination. The influences of calcination temperature, time and Li/Mn ratio on the crystal structure and the particle size of Li_xMn₂O₄ were investigated. It was shown that the higher the calcination temperature, the more complete the crystal structure, and the larger the particle size. Moreover, the influence of calcination time on the crystal structure was insignificant when it was more than 3h at 700℃. With the increase of x in Li_xMn₂O₄ in the range of 0.6～1.0, the d111 and lattice parameter a increased first and then decreased. The electrochemical properties of nano-spinel LiMn₂O₄ using as cathode material of lithium-ion battery were studied. The low discharge capacity might be due to the irreversible capacity loss brought by the large surface area and lattice vacancies of the nano-spinel.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

有机溶液中电化学制备纳米MgTiO3

In a cell without separating the cathode and anode spaces, the precursor MgTi(OCH₂CH₃)_(6-y)(acac)_y of the mixed oxide MgTiO₃ was directly synthesized by electrochemical dissolution of titanium for 4 hours and then of magnesium for 1 hour 40 minutes at the current of 0.2 A in ethanol and acetyl-acetone solution. The nano- MgTiO₃ powder was prepared by a direct sol-gel process of the electrolyte solution under pH≈8.5 followed by washing, drying in vacuum for 24 h, and calcination at 500 ℃ for 2 h. IR and Raman spectroscopy, XRD, and TEM were used to investigate the structure of nano-MgTiO₃ and its precursor. The result suggested that it was more appropriate to control the temperature between 35～40 ℃ and the concentration of conductive additive (Bu₄N)Br at 0.04 mol·L^-1. The xerogel with an average particle size of 12 nm and the nano-MgTiO₃ of 20 nm was thus obtained in a high purity.     

掺镍型层状LixNiyMn1-yO2正极材料的合成与电性能研究

A kind of cathode material of layered Li_xNi_yMn_1-yO₂ characterized with the O2 type has been synthesized by a simple method. Its precursor Na_xNi_yMn_1-yO₂ has been prepared from manganese dioxide， nickel hydroxide and sodium carbonate at high temperature in air and quickly cooled in cold water， then it has been exchanged by the melted LiNO₃ at 300～400℃ in air. The effects of calcine-temperature for the precursors and its compositions (the content of Na and Ni) on the electrochemical properties of the material Li_xNi_yMn_1-yO₂ have been investingated by XRD and electrochemical tests. The results show that the sample Li_0.7Ni_0.3Mn_0.7O₂， has the best electrochemical properties which shows only one charge-discharge potential stage of 2.8～3.0V and has a high specific capacity over 180mAh·g^-1 cycled between 2.0～4.20V. A significant structure transformation to the spinal-type phase has not been found in the charge-discharge cycling and the discharge specific capacity around 165mAh·g^-1 has re-mained after the 20th cyclings for the material.     

层状钙钛矿型Sm2-2xSr1+2x-2yCa2yMn2O7(x=0.2，0.3，0.4，0.5；y=0，0.2，0.3)的溶胶凝胶合成及电性能研究

Layered perovskite manganites with a nominal chemsitry of Sm_2-2xSr_1+2x-2_yCa_2yMn₂O₇(x=0.2, 0.3, 0.4, 0.5; y=0, 0.2, 0.3) were prepared using sol-gel method. The crystal structures of these compounds were studied by X-ray diffraction (XRD) and FTIR absorption spectra. The absorption peaks become weaker and move a little to higher frequency with increasing of Sm/Sr concentration. As the Sm doping increases to x=0.2 and x=0.3, the absorption peaks show a cubic structure character, reflecting that the samples suffer from a transition from tetragonal structure to cubic structure. This coincides with the X-ray diffraction results. The high temperature electrical properties were studied by conventional four-probe method. Although all samples exhibit the semiconductive behavior, lnρ-1 000/T curves are not linear and they obey the small polaron hopping mechanism. Moreover, the resistivity decreases with x reducing. This is due to that Sm doping increases the Jahn-Teller ion Mn³⁺/Mn⁴⁺ ratio, and decreases the e_g bandwidth.     

电镀烧结法制备Ti/SnO2-Sb2O4电极的研究

The Ti/SnO₂-Sb₂O₄ electrode has been prepared by the electroplate-sinter method. The effect of SbCl₃ adding amount and sintering temperature on its electrode lifetime and oxygen evolution potential were investigated by means of EDX, SEM and XRD analysis. The results indicated that the electrode appeared the best performance when the SbCl₃ adding amounts was 0.2g and the sintering temperature was 550℃. In optimized conditions Ti substrate was entirely covered by SnO₂-Sb₂O₄ and the combinations among them were tight. Due to the use of electroplate method, the electrical conductivity, the oxygen evolution potential and the electrode lifetime were increased, so the elec-tro-catalytic activity and the electrochemical stability of the prepared electrode were found to be superior.     

BaTiO3/ IPNs的制备及介电性能与阻尼性能的相关性

BaTiO₃/ Interpenetrating Polymer Networks (IPNs) composites were prepared by combination of BaTiO₃nanocrystal in tetragonal system and polyurethane(PU) / unsaturated polyester (UP) interpenetrating polymer networks (IPNs). The tetragonal nanocrystalline BaTiO₃was obtained by hydrothermal process and calcination at 1 200 ℃. The prepared materials were polarized with high voltage and small current, and protected by silicon oil. The morphology of BaTiO₃/ IPNs and the effect of combination of BaTiO₃on the damping behavior of IPNs were studied. The relationship between damping performance and dielectric charater was also discussed in terms of dielectric constant and dielectric loss measured. The results show that the areas under loss modulus (E″) and the values of loss factors (tanδ) were both increased by combination of BaTiO₃into IPNs system. The maximum value of E″ increased above 100 MPa compared with pure IPNs and the extent increased more remarkably after polarizing process. The main and shoulder peak of tanδ curves both moved toward higher temperature ranges, and the temperature ranges of tanδ>0.3 was higher than 100 ℃. Moreover, through polarizing process, the composites exhibited synergistic action caused by elastomeric damping, interfacial abrasive damping and piezoelectric damping mechanisms. The relationship study of damping property and dielectric characters showed that the temperature ranges exhibited excellent consistency of maximum dielectric loss and modulus with damping loss factor.     

多元掺杂尖晶石型Li1.02MxMn2-xQyO4-y正极材料的电化学特性

The effect of doping on the electrochemical performance was studied for spinel type Li_1.02M_xMn_2-xQ_yO_4-y used as cathode material in lithium-ion battery. TG/DTA curves of the precursor(the raw materials) doped with different elements were studied. The spinel materials Li_1.02Mn₂O₄, Li_1.02Co_0.02Cr_0.01La_0.01Mn_1.96F_0.02O_3.98, Li_1.02Co_0.02Cr_0.01 La_0.01Mn_1.96Cl_0.02O_3.98, Li_1.02Co_0.02La_1.02Mn_1.97Cl_0.02O_3.98, Li_1.02Co_0.02Cr_0.01Mn_1.97O₄, were prepared by solid-state reaction method after the pretreatment of conversion under low temperature and uniform mixing. X-ray diffraction patterns showed that all the samples had perfect spinel structure. SEM indicated that the particles of the samples had uniform size and were distributed evenly. The results of the charge/discharge curves showed that Li_1.02Co_0.02Cr_0.01La_0.01Mn_1.96F_0.02O_3.98 had better performance than other materials according to the inhibition of decline of reversible capacity of spinel Li_1.02M_xMn_2-xQ_yO_4-y. Therefore, cycle performance had been improved so obviously that 93.9% of the initial capacity were preserved after 100 cycles. Furthermore, electrochemical impedance tests were carried out with the spinel Li_1.02Co_0.02Cr_0.01La_0.01Mn_1.96F_0.02O_3.98 as working electrode, Lithium as counter electrode and reference electrode. Results showed that this material possessed good charge/discharge reversible capability and had the lowest impedance in 3.95～4.25 V range (on the stage of charge / discharge).     

Sr3SiO5∶Eu2+荧光粉的微波合成及性能研究

Silicate orange yellow phosphor used in white-light LED was prepared by microwave method. The structure and optical properties of phosphor were studied. Sr₃SiO₅∶Eu²⁺ phosphor synthesized by microwave method is tetragonal structure of Sr₃SiO₅ with uniform particle distribution. Luminescence spectrum is a broad band spectrum peaking at 575 nm. The peak of excitation is at 532 nm and phosphor can be excited by blue LED. The warm white light was obtained combined phosphor and blue LED. The CIE chromaticity coordinates and correlated color temperature of white light is (x=0.394, y=0.341) and 3 239 K respectively.     

Ni_xCu_(1-x)Fe_2O_4的H_2/CO_2氧化还原反应性能

完全还原的NixCu1-xFe2O4(x=0.25,0.5,0.75)可用来分解CO2。采用共沉淀法制备了NixCu1-xFe2O4(x=0.25,0.5,0.75)系列铁酸盐的纳米微粒,利用H2-TG数据分析NixCu1-xFe2O4(x=0.25,0.5,0.75)中Cu2+的还原反应动力学数据,得出表观活化能Ea并不是单纯随着Ni2+或Cu2+含量的变化而变化,当x=0.25时反应活化能具有最大值。通过CO2-TG比较不同样品经H2完全还原后分解CO2的活性,得出Ni0.5Cu0.5Fe2O4具有最低的起始反应温度和最大的分解活性,并采用XRDRietveld拟合方法对Ni0.5Cu0.5Fe2O4的完全还原产物和分解CO2产物进行物相分析。     

The structure Tl3SbS3, Tl3SbSe3, Tl3SbS3−xSex, and Tl3SbyAs1−ySe3

The space group symmetry and crystal structure of Tl₃SbS_3−xSe_x compounds in the composition range 0 < x < 3 have been determined by a combination of powder X-ray diffraction, electron diffraction, and high-resolution electron microscopy. The incongruently melting compound Tl₃SbSe₃ has been shown to crystallize in cubic space group P2₁3 with a = 9.435Å in a structure related to that of Langbeinite. The convergent beam electron diffraction pattern of Tl₃SbS₃ is in accord with the space group R3m determined by X-ray diffraction. The cubic Langbeinite-type structure is found for Tl₃SbS_3−xSe_x for 0.5 < x < 3 and for Tl₃Sb_yAs_1−ySe₃ for 0.077 < y < 1.0. A five-component compound Tl₃Sb_0.5As_0.5Se_1.5S_1.5 was also found to be cubic.     

MnOx/Al2O3催化剂低温SCR脱硝性能

采用浸渍法制备了MnO_x/Al_2O_3低温脱硝催化剂,研究了Mn的含量对MnO_x/Al_2O_3催化剂低温烟气中NOx脱除率的影响,并通过XRD、SEM、BET、XPS、NH_3-TPD和H_2-TPR等手段对催化剂进行了表征.结果表明,当Mn含量为9%,空速为45 000 h-1时,MnO_x/Al_2O_3催化剂NO_x脱除率最高,在220℃时达79%;9MnO_x/Al_2O_3催化剂表面MnO_x氧化物分散较均匀,且稳定性及抗H_2O性能较好,但抗SO_2性能有待提高;MnO_x/Al_2O_3催化剂孔径主要分布在4~20 nm范围内,Mn含量对催化剂孔径变化影响较小;催化剂中活性组分Mn主要以Mn~(3+)和Mn~(4+)的形式存在;Mn~(4+)和Oα含量增加有利于NO_x的脱除;且添加Mn后,活性酸位点的数量增长,增强了催化剂还原能力,促进了NO_x脱除率的增加.     

纳米复合材料Ag/MxOy-TiO2(MxOy=ZnO、Al2O3和Fe2O3)的制备及其微波辅助光催化降解甲基橙

采用溶胶-凝胶-程序升温溶剂热一步法,利用表面活性剂EO₂₀PO₇₀EO₂₀(P123)作为模板剂,分别制备了三元纳米复合材料Ag/ZnO-TiO₂、Ag/Al₂O₃-TiO₂和Ag/Fe₂O₃-TiO₂。通过XRD、氮气吸附-脱附测定、TEM以及扫描电子显微镜配合X-射线能量色散谱仪(SEM-EDS)等对合成的3种催化剂进行了对比表征分析。结果表明,复合材料Ag/M_xO_y-TiO₂中Ag以单质形式存在并较好地分布在M_xO_y-TiO₂表面上。所合成产物颗粒尺寸较小(约10 nm左右),形貌较好。其中,Ag/ZnO-TiO₂的比表面积与Ag/Al₂O₃-TiO₂十分相近,略大于Ag/Fe₂O₃-TiO₂。光催化活性研究中,以甲基橙为模型分子且辅以微波场作用。结果显示,上述三元复合材料的活性均明显高于未掺杂银的二元复合材料,其中Ag/ZnO-TiO₂的光催化活性最好,在90 min内对甲基橙的降解率高达86%。     

Electronic structure of magnetic semiconductors Cd1 ? xMnxGeAs2 and Cu1 ? xMnxGaTe2

The band structures of pure semiconductors CdGeAs₂ and CuGaTe₂, as well as magnetic semiconductors Cd_{1 − x} Mn _x GeAs₂ and Cu_{1 − x} Mn _x GaTe₂ (x = 0.0625), have been calculated by the density functional theory method. In both compounds, the Mn3d orbitals form a narrow band near the Fermi level. In the case of Cd_{1 − x} Mn _x GeAs₂, the Mn3d orbitals are slightly involved in chemical bonding. In the case of Cu_{1 − x} Mn _x GaTe₂, the same orbitals are considerably involved in chemical bonding. The relationship of these results with the properties of the compounds and ferromagnetism models is discussed. Original Russian Text ? S.V. Murashov, V.G. Yarzhemsky, V.I. Nefedov, E.N. Murav’ev, 2007, published in Zhurnal Neorganicheskoi Khimii, 2007, Vol. 52, No. 8, pp. 1327–1331.     

Simulation of dielectric properties and stability of clusters (H2O)i, CO2(H2O)i, and CH4(H2O)i

Molecular dynamics method is used for studying complex permittivity ɛ and the stability of individual water clusters as a function of the number of involved molecules (7 ≤ i ≤ 20) and also the corresponding characteristics of water aggregates with a captured CO₂ or CH₄ molecule. Absorption of the latter molecules leads to considerable changes in dielectric properties and stability of clusters. In particular, upon the addition of a CO₂ molecule to a water cluster, the oscillation parameters of the real and imaginary parts of the permittivity change. Capture of a CH₄ molecule by a water aggregate changes the ɛ(ω) dependence from the relaxation to resonance type. For i ≥ 15, the thermal stability of individual water clusters can be lower than that of aggregates CO₂(H₂O) _i and CH₄(H₂O) _i . The mechanical stability of (H₂O) _{i ≥ 13} clusters can exceed that of heteroclusters under consideration. Clusters (H₂O) _i and CO₂(H₂O) _i have approximately the same dielectric stability, whereas aggregates CH₄(H₂O) _i exhibit lower stability with respect to electric perturbations. Original Russian Text ? A.E. Galashev, V.N. Chukanov, A.N. Novruzov, O.A. Novruzova, 2007, published in Elektrokhimiya, 2007, Vol. 43, No. 2, pp. 143–153.     

Global minima of (C60)nCa, (C60)nF and (C60)nI clusters

Likely candidates for the lowest potential energy minima of (C₆₀)_nCa²⁺, (C₆₀)_nF⁻ and (C₆₀)_nI⁻ clusters are located using basin-hopping global optimisation. In each case, the potential energy surface is constructed using the Girifalco form for the C₆₀ intermolecular interaction, an averaged Lennard–Jones C₆₀–ion interaction, and a polarisation potential, which depends on the first few non-vanishing C₆₀ multipole polarisabilities. We find that the ions generally occupy the interstitial sites of a (C₆₀)_n cluster, the coordination shell being tetrahedral for Ca²⁺ and F⁻. The I⁻ ion has an octahedral coordination shell in the global minimum for (C₆₀)₆I⁻, however for 12  n  8 the preferred coordination geometry is trigonal prismatic.     

SiO2负载氮掺杂TiO2可见光响应光催化剂的制备及性能

以四氯化钛为钛源,尿素为氮源,采用液相水解-沉淀法制得SiO2负载N掺杂TiO2可见光响应TiO2-xNy/SiO2光催化剂(TSN)。以苯酚为模型物,考察了TSN在可见光区、紫外光区及太阳光下的光催化活性,以及催化剂的使用寿命、分离性能。采用XPS、FTIR、UV-Vis DRS、XRD、TEM和低温氮物理吸附等对催化剂的结构进行表征。结果表明,N以阴离子形式进入TiO2体相并置换晶格中的O,适量N掺杂的TSN在紫外光区、可见光区及太阳光下均表现出较高的活性。SiO2与TiO2界面间有Ti-O-Si键形成,结合牢固。N掺杂在TiO2表面生成Ti-O-N键,形成新的能级结构,使催化剂的吸收红移至450~500 nm,诱发TiO2可见光催化活性。SiO2负载可减小TiO2颗粒平均尺寸,增加催化剂比表面积;同时SiO2负载还可改善催化剂的分离性能,提高催化剂使用寿命。     

The regular features of chlorine formation in the systems NaCl-MexOy-O2 and Ca(Zn)Cl2-MexOy-O2

The reaction of sodium, calcium, and zinc chlorides with atmospheric oxygen in the presence of transition metal oxides and antimony oxide at temperatures exceeding the melting temperatures of chlorides was studied. The content of chorine, product of oxidation of chloride ions in molten NaCl and CaCl₂, was determined as a function of the polarization force of cations of transition metal oxides.     

Au10(TBBT)10: the Begining and the End of Aun(TBBT)m Nanoclusters

Gold(I) thiolate compounds (i.e. Au^I-SR) are important precursors for the synthesis of atomically precise Au_n(SR)_m nanoclusters. However, the nature of the Au^I-SR precursor remains elusive. Here, we report that the Au₁₀(TBBT)₁₀ complex is a universal precursor for the synthesis of Au_n(TBBT)_m nanoclusters (where TBBT=4-tertbutylbenzenethiol/thiolate). Interestingly, the Au₁₀(TBBT)₁₀ complex is also found to be re-generated through extended etching of the Au_n(SR)_m nanoclusters with excess of TBBT thiol and O₂. The formation of well-defined Au₁₀(TBBT)₁₀ complex, instead of polymeric Au^I-SR, is attributed to the bulkiness of the TBBT thiol. Through 1D and 2D NMR characterization, the structure of Au₁₀(TBBT)₁₀ is correlated with the previously reported X-ray structure, which contains two inter-penetrated Au₅(TBBT)₅ rings. The photophysical property of Au₁₀(TBBT)₁₀ complex is further probed by femtosecond transient absorption spectroscopy. The accessibility of the precise Au₁₀(TBBT)₁₀ precursor improves the efficiency of the synthesis of the Au_n(TBBT)_m nanoclusters and is expected to further facilitate excellent control and understanding of the reaction mechanisms of nanocluster synthesis.