Electrosynthesis and electrochromic properties of free‐standing copolymer based on oligo(oxyethylene) cross‐linked 2,2’‐bithiophene and 3,4‐ethylenedioxythiophene

Oligo(oxyethylene) chains cross‐linked 2,2’‐bithiophene (BT‐E5‐BT) has been synthesized successfully. A free‐standing copolymer film based on BT‐E5‐BT and 3,4‐ethylenedioxythiophene (P(BT‐E5‐BT‐co‐EDOT)) has been synthesized by electrochemical polymerization. The electrical conductivity of P(BT‐E5‐BT‐co‐EDOT) copolymer (16 S m^?1) has improved by four orders of magnitude compared to the homopolymer of BT‐E5‐BT (P(BT‐E5‐BT), 5 × 10^?3 S m^?1) at room temperature. Both homopolymer and copolymer films exhibit well‐defined redox and satisfied coloration efficiency. Spectroelectrochemistry studies indicate that the P(BT‐E5‐BT‐co‐EDOT) has a lower band gap in the range of 1.83–1.90 eV and shows more plentiful electrochromic colours (green, blue, purple and salmon pink) compared with the homopolymer P(BT‐E5‐BT). The Copolymer P(BT‐E5‐BT‐co‐EDOT) shows the moderate optical contrast (26% of 480 nm) and coloration efficiency (205.41 cm^?1 C^?2). The copolymer method provides a novel way to fabricate a free‐standing organic electrochromic device. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1583–1592     

Poly(thieno[3,4‐b]‐1,4‐oxathiane) and poly(3,4‐ethylenedioxythiophene‐co‐thieno[3,4‐b]‐1,4‐oxathiane)/poly(styrene sulfonic sodium): Preparation,characterization, and optoelectronic performance

In this work, the asymmetrical analog of 3,4‐ethylenedioxythiophene (EDOT), thieno[3,4‐b]‐1,4‐oxathiane (EOTT), was synthesized and chemically polymerized first in aqueous solution using poly(styrene sulfonic sodium) (PSS) as the polyelectrolyte to yield poly(thieno[3,4‐b]‐1,4‐oxathiane) (PEOTT)/PSS. As‐formed film exhibited low electrical conductivity (～10^?4 S/cm). Alternatively, EOTT together with EDOT (in different molar ratio of 1:1 and 1:5) was copolymerized and the polymer poly(EOTT‐co‐EDOT)/PSS had electrical conductivity of 10^?1 S/cm. After dimethyl sulfoxide (DMSO) treatment, the electrical conductivity was enhanced to 10⁰ S/cm; however, the conductivity of the above homopolymer was reduced (～10^?5 S/cm). Raman spectroscopy was used to interpret conductivity enhancement or reduction after DMSO treatment. The conductivity decrease of PEOTT/PSS compared to poly(EOTT‐co‐EDOT)/PSS may arise from the conformational change of PEOTT backbone from the quasi‐planar to the distorted planar mode induced by PSS^–/PSSH through ionic interaction. Kinetic studies revealed that the copolymer had high coloration efficiencies (375 cm²/C), low switching voltages (?0.8 to +0.6 V), decent contrast ratios (45%), moderate response time (1.0 s), excellent stability, and color persistence. An electrochromic device employing poly(3‐methylthiophene) and poly(EOTT‐co‐EDOT)/PSS as the anode and cathode materials was also studied. From these results, poly(EOTT‐co‐EDOT)/PSS would be a promising candidate material for organic electronics. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2285–2297     

单体摩尔比对共聚物电化学及电致变色性质的影响

通过电化学聚合法制备了3, 6-(二噻吩基)-9-(二茂铁甲酸己酯基)-咔唑(BTC-H-Fc)与3, 4-乙烯二氧噻吩(EDOT)不同摩尔比下的共聚物,并运用电化学、傅里叶变换红外(FT-IR)光谱及光谱电化学对其结构与性能进行了表征。研究结果表明所得共聚物均能显示良好的电化学特性,光谱电化学测试结果表明,当摩尔浓度比为1时, P(BTC-H-Fc:EDOT)-1中性态下表现浅绿色,且随着施加电压增加转变为绿色和紫色; P(BTC-H-Fc:EDOT)-4则显示了最丰富的颜色,可在中性态的红褐色、棕黄色、绿色、蓝色和紫色五种颜色之间可逆变换;当摩尔比继续增加时, P(BTC-H-Fc:EDOT)-8可以显示红褐色、灰黑色、蓝绿色和天空蓝四种颜色。另外,三种摩尔比的聚合物薄膜还具有不错的光学对比度,转换响应时间及着色效率,该性能为其在电致变色器件的应用提供了潜力。     

A Free‐standing electrochromic material of poly(5,7‐bis(2‐(3,4‐ethylenedioxy)thienyl)‐indole) and its application in electrochromic device

Free‐standing poly(5,7‐bis(2‐(3,4‐ethylenedioxy)thienyl)‐indole) (PETI) was electrochemically obtained from 5,7‐bis(2‐(3,4‐ethylenedioxy)thienyl)‐indole (ETI) prepared by Stille coupling reaction of 5,7‐dibromoindole and 3,4‐ethylenedioxythiophene. For comparison, poly(5,7‐bis(2‐thiophene)‐indole) was also electrosynthesized from 5,7‐bis(2‐thiophene)‐indole (BTI) which was prepared from the 5,7‐dibromoindole and thiophene. Characterizations of ETI and BTI were performed by cyclic voltammetry, scanning electron microscopy, ¹H NMR, and ¹³C NMR spectroscopy. Spectroelectrochemical studies showed PETI had better electrochromic properties and showed two different colors (brown and blue‐violet) under various potentials with better maximum contrast (ΔT%) and coloration efficiency (CE). An electrochromic device (ECD) based on PETI and poly(3,4‐ethylenedioxythiophene) (PEDOT) was also constructed and characterized. This ECD had fast response time, high CE, better optical memory, and long‐term stability. These results indicated that PETI had potential applications for ECD. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2356–2364     

Phenothiazine‐S,S‐dioxide‐ and fluorene‐based light‐emitting polymers: Introduction of e−‐deficient S,S‐dioxide into e−‐rich phenothiazine

A novel series of poly(10‐hexyl‐phenothiazine‐S,S‐dioxide‐3,7‐diyl) and poly(9,9′‐dioctyl‐fluorene‐2,7‐diyl‐alt‐10‐hexyl‐3,7‐phenothiazine‐S,S‐dioxide) (PFPTZ‐SS) compounds were synthesized through Ni(0)‐mediated Yamamoto polymerization and Pd(II)‐catalyzed Suzuki polymerization. The synthesized polymers were characterized by ¹H NMR spectroscopy and elemental analysis and showed higher glass transition temperatures than that of pristine polyfluorene. In terms of photoluminescence (PL), the PFPTZ‐SS compounds were highly fluorescent with bright blue emissions in the solid state. Light‐emitting devices were fabricated with these polymers in an indium tin oxide/poly(3,4‐ethylene dioxythiophene):poly(styrene sulfonate)/polymer/Ca/Al configuration. The electroluminescence (EL) of the copolymers differed from the PL characteristics: the EL device exhibited a redshifted greenish‐blue emission in contrast to the blue emission observed in the PL. Additionally, this unique phenothiazine‐S,S‐dioxide property, triggered by the introduction of an electron‐deficient SO₂ unit into the electron‐rich phenothiazine, gave rise to improvements in the brightness, maximum luminescence intensity, and quantum efficiency of the EL devices fabricated with PFPTZ‐SS. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1236–1246, 2007     

Electrochromic enhancement of poly(3,4‐ethylenedioxythiophene) films functionalized with hydroxymethyl and ethylene oxide

2‐((2,3‐Dihydrothieno[3,4‐b]dioxin‐2‐yl)methoxy)methyl oxirane (EDOT‐MO) was successfully synthesized by the reaction of epichlorohydrin with hydroxymethylated‐3,4‐ethylenedioxylthiophene (EDOT‐MeOH), which was synthesized via a simple four‐step sequence. Poly(hydroxymethylated‐3,4‐ethylenedioxylthiophene) (PEDOT‐MeOH) and poly(2‐((2,3‐dihydrothieno[3,4‐b]dioxin‐2‐yl)methoxy)methyl oxirane) (PEDOT‐MO) were electrosynthesized through electropolymerization of EDOT‐MeOH and EDOT‐MO, respectively. Structural, electrochemical, optical, and thermal properties of as‐formed polymers were investigated by FTIR, cyclic voltammetry, UV–vis, and thermogravimetry. Spectroelectrochemistry studies demonstrated that PEDOT‐MeOH and PEDOT‐MO could be reversibly oxidized and reduced accompany with obvious color changes. Further kinetic studies demonstrated that the introduction of hydroxymethyl or ethylene oxide group significantly improved electrochromic properties of 3,4‐ethylenedioxythiophene (PEDOT) and resulted in high contrast ratios (57.3% at 585 nm) and coloration efficiencies (338.5 cm² C^?1), low switching voltages, and fast response time. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1989–1999     

Synthesis and characterization of novel germanium‐containing poly(p‐phenylenevinylene) derivatives

Novel blue‐emitting germanium‐containing poly(p‐phenylenevinylene) (PPV) derivatives with well‐defined conjugation lengths were synthesized via Wittig‐condensation polymerizations. The polymers can be color‐tuned by the introduction of various chromophores into the PPV‐based polymer backbones. The photoluminescence (PL) spectra of the polymers, GePVK (containing carbazole moieties), GeMEH (containing dialkoxybenzene moieties), and GePTH (containing phenothiazine moieties), were found to exhibit blue, greenish blue, and green emissions, respectively. GePTH produces more red‐shifted emission than GeMEH and GEPVK, resulting in green emission, and the solution and solid state PL spectra of GePVK consist of almost blue emission. The electroluminescence spectra of GeMEH and GePTH contain yellowy green and yellow colors, respectively. Interestingly, GePVK exhibits white emission with CIE coordinates of (0.33, 0.37) due to electroplex emission in the light‐emitting diodes. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 979–988, 2008     

Novel chiral PEDOTs for selective recognition of 3,4‐dihydroxyphenylalanine enantiomers: Synthesis and characterization

Two new 3,4‐ethylenedioxythiophene (EDOT) derivatives, (2R)‐(2,3‐dihydrothieno[3,4‐b][1,4]dioxin‐2‐yl)methyl 2‐phenylpropanoate ((R)‐EDTM‐PP) and (2S)‐(2,3‐dihydrothieno[3,4‐b][1,4]dioxin‐2‐yl)methyl 2‐phenylpropanoate ((S)‐EDTM‐PP), were synthesized and electropolymerized in dichloromethane (CH₂Cl₂) and terabutylammonium hexafluorophosphate (Bu₄NPF₆) system. As chiral electrodes, poly((2R)‐(2,3‐dihydrothieno[3,4‐b][1,4]dioxin‐2‐yl)methyl 2‐phenylpropanoate) ((R)‐PEDTM‐PP) and poly((2S)‐(2,3‐dihydrothieno[3,4‐b][1,4]dioxin‐2‐yl)methyl 2‐phenylpropanoate) ((S)‐PEDTM‐PP)‐modified glassy carbon electrodes (GCEs) were employed to successfully recognize 3,4‐dihydroxyphenylalanine (DOPA) enantiomers. Cyclic voltammetry presents that (R)‐PEDTM‐PP and (S)‐PEDTM‐PP had good redox activity and stability. Spectroelectrochemistry studies revealed (R)‐PEDTM‐PP and (S)‐PEDTM‐PP polymers have electronic bandgap of 1.68 and 1.66 eV, and could be reversibly oxidized and reduced accompanying with obvious color changes from dark blue to light purple. In addition, the electrochemical behavior, structural characterization, thermal stability, morphology and circular dichroism of (R)‐PEDTM‐PP and (S)‐PEDTM‐PP films were investigated in detail. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2238–2251     

Electrochromic Properties of ‘Trimeric' Thiophene‐pyrrole‐thiophene Derivative Grown from Electrodeposited 6‐(2,5‐di(thiophen‐2‐yl)‐1H‐pyrrol‐1‐yl)hexan‐1‐amine and its Copolymer

A centrosymmetric polymer precursor, namely 6‐(2,5‐di(thiophen‐2‐yl)‐1H‐pyrrol‐1‐yl)hexan‐1‐amine (TPHA), was synthesized via a Knorr–Paal reaction using 1,4‐di(2‐thienyl)‐1,4‐butanedione and hexane‐1,6‐diamine. The resultant monomer was characterized by Nuclear Magnetic Resonance (¹H‐NMR). Electroactivity of TPHA was investigated via cyclic voltammetry. The electronic structure and the nature of electrochromism in P(TPHA) and its copolymer with EDOT, (P(TPHA‐co‐EDOT)), were examined via spectroelectrochemistry studies. P(TPHA) switches between claret red neutral state and blue oxidized state. Optical response times for coloring and bleaching processes of the P(TPHA) and P(TPHA‐co‐EDOT) were found as 2.1 s and 1.6 s, respectively.

The copolymer of TPHA was used to construct dual type polymer electrochromic devices (ECDs) against poly(3,4‐ethylenedioxythiophene) (PEDOT). Spectroelectrochemistry and electrochromic switching out of the devices were investigated.     

Palladium on carbon‐catalyzed direct C—H arylation polycondensation of 3,4‐ethylenedioxythiophene with various dibromoarenes

We have demonstrated a direct arylation polycondensation of 3,4‐ethylenedioxythiophene with 2,7‐dibromo‐9,9‐dioctylfluorene using palladium on carbon (Pd/C) as a catalyst. Pd/C is a low‐cost solid‐supported palladium catalyst, giving one of the effective catalytic systems for direct arylation. The Pd/C‐catalyzed direct arylation polycondensation with acetic acid/potassium carbonate in N,N‐dimethylacetamide furnished a high molecular weight π‐conjugated alternating copolymer of EDOT‐fluorene (M_n = 89,300, M_w/M_n = 3.27) in high yield. The polycondensation of EDOT with various dibromoarenes was also achieved, giving EDOT‐carbazole, EDOT‐dialylamine, and EDOT‐bithiophene polymers. Optical and electrochemical properties of the polymers were also discussed. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 55, 1183–1188     

A novel high‐contrast ratio electrochromic material from spiro[cyclododecane‐1,9′‐fluorene]bicarbazole

A novel electroactive spirocyclododecylfluorene monomer named 2,7‐bis(carbazol‐9‐yl)‐9,9′‐spiro[cyclododecane‐1,9′‐fluorene] (SFC) was synthesized and electrochemically polymerized to give a very stable multi‐electrochromic polymer (poly‐SFC). Two separate oxidation processes were observed for both SFC monomer and poly‐SFC that carries two carbazole units. The polymeric film of poly‐SFC was coated onto ITO/glass surface, and it shows different colors (transparent, yellowish green, green, and dark green) upon stepwise oxidations. An electrochromic device based on poly‐SFC was assembled in the sandwich cell configuration of ITO/poly‐SFC//gel electrolyte//PEDOT/ITO. Poly‐SFC exhibits 90% of transparency at neutral state and a high contrast ratio (ΔT = 58% at 800 nm). This device constructed from it represents a response time of about 1 s, high coloration efficiency (1377 cm² C^–1) and retained its performance by 96.4% even after 1000 cycles. Exhibiting high transparency at neutral state, reversible redox behavior, resistance to overoxidation, and especially high contrast ratio at near IR region can make poly‐SFC be useful and promising candidate for electrochromic applications despite having a relatively slow response time. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

High‐efficiency blue light‐emitting polymers based on 3,6‐silafluorene and 2,7‐silafluorene

A novel blue‐emitting polymer based on 3,6‐silafluorene and 2,7‐silafluorene was synthesized via the Suzuki polycondensation. The resulting polymers are readily soluble in common organic solvents, such as toluene, xylene, THF, and chloroform. The thermal, electrochemical, photophysical, and electroluminescence properties of the resulting polymers were investigated. The device fabricated from the copolymer with a configuration of ITO/PEDOT:PSS/PVK/polymer/Ba/Al exhibited an external quantum efficiency of 1.95%, a luminous efficiency of 1.69 cd A^?1 and a maximal brightness of 6000 cd m^?2. It has been found that the incorporation of the 3,6‐silafluorene unit into the poly(2,7‐silafluorene) main chain can not only improve the color purity of the devices from the resulting copolymer but also enhance its device efficiency. Moreover, no undesired long‐wavelength green emission was observed in the PL spectra of P36‐27SiF90 compared to that of PFO with a dominating emission at 500–600 nm after thermal annealing at 200 °C for 8 h. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4941–4949, 2007     

High red,green, and blue color purity electroluminescence from MEH‐PPV and polyalkyfluorenes‐based bright white polymer light emitting displays

A series of white polymer light emitting displays (PLEDs) based on a polymer blend of polyalkylfluorenes and poly(2‐methoxy‐5,2′‐ethyl‐hexyloxy‐1,4‐phenylene vinylene) (MEH‐PPV) was developed. MEH‐PPV or red light emitting alkyfluorene copolymer (PFR) was blended with blue light emitting alkyfluorene copolymer (PFB), and MEH‐PPV was blended with both green light emitting alkyfluorene copolymer (PFG) and PFB to generate white light emission PLEDs. Low turn on voltage (2.7 V), high brightness (12,149 nits), high efficiency (4.0 cd/A, 4.0 lm/W), and good color purity (Commission Internationale de L'Eclairage (CIE_x,y) co‐ordinates (0.32, 0.34)) were obtained for the white PLEDs based on the PFB and MEH‐PPV polymer blend. Exciplex formation in the interface between PFR and PFB induced a new green emission peak for these two components based white PLEDs. As a result, strong white emission (4078 nits) was obtained by mixing the red, green, and blue (RGB) three primary colors. High color purity of blue (CIE, x = 0.14, y = 0.08), green (CIE, x = 0.32, y = 0.64) and red (CIE, x = 0.67, y = 0.33) emissions was achieved for white PLEDs combining with dielectric interference color‐filters. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 330–341, 2007     

Red,green, and blue electrochromism in ambipolar poly(amine–amide–imide)s based on electroactive tetraphenyl‐p‐phenylenediamine units

A series of novel poly(amine–amide–imide)s (PAAIs) based on tetraphenyl‐p‐phenylenediamine (TPPA) units showing anodically/cathodically electrochromic characteristic with three primary colors [red, green, and blue (RGB)] were prepared from the direct polycondensation of the TPPA‐based diamine monomer with various aromatic bis(trimellitimide)s. These multicolored electrochromic polymers were readily soluble in polar organic solvents and showed excellent thermal stability associated with high glass‐transition temperatures (288–314 °C) and high‐char yield (higher than 60% at 800 °C in nitrogen). The PAAI films revealed electrochemical oxidation and reduction accompanied with high contrast of optical transmittance color changes from the pale yellow neutral state to the green/blue oxidized state and red reduced state, respectively. The electrochromic films had high‐coloration efficiency (CE = 178 and 242 cm²/C at the first and the second stages, respectively), low‐switching time, and good redox stability, which still retained a high electroactivity after long‐term redox cycles. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and characterization of indeno[1,2‐b]fluorene‐based white light‐emitting copolymer

An indenofluorene‐based copolymer containing blue‐, green‐, and red light‐emitting moieties was synthesized by Suzuki polymerization and examined for application in white organic light‐emitting diodes (WOLEDs). Tetraoctylindenofluorene (IF), 2,1,3‐benzothiadiazole (BT), and 4,7‐bis(2‐thienyl)‐2,1,3‐benzothiadiazole (DBT) derivatives were used as the blue‐, green‐, and red‐light emitting structures, respectively. The number‐average molecular weight of the polymer was determined to be 25,900 g/mol with a polydispersity index of 2.02. The polymer was thermally stable (T_d = ～398 °C) and quite soluble in common organic solvents, forming an optical‐quality film by spin casting. The EL characteristics were fine‐tuned from the single copolymer through incomplete fluorescence energy transfer by adjusting the composition of the red/green/blue units in the copolymer. The EL device using the indenofluorene‐based copolymer containing 0.01 mol % BT and 0.02 mol % DBT units ( PIF‐BT01‐DBT02 ) showed a maximum brightness of 4088 cd/m² at 8 V and a maximum current efficiency of 0.36 cd/A with Commission Internationale de L'Eclairage (CIE) coordinates of (0.34, 0.32). The EL emission of PIF‐BT01‐DBT02 was stable with respect to changes in voltage. The color emitted was dependent on the thickness of the active polymer layer; layer (～60 nm) too thin was unsuitable for realizing WOLED via energy transfer. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3467–3479, 2009     

Synthesis and properties of conjugated copolycondensates consisting of carbazole‐2,7‐diyl and fluorene‐2,7‐diyl

Carbazole and fluorene‐based random and alternating copolycondensates were synthesized to develop high‐performance blue light‐emitting polymers by improving electron injection ability of poly(N‐aryl‐2,7‐carbazole)s that showed intense blue electroluminescence (EL) with good hole‐injection and ‐transport ability. These copolycondensates absorbed light energy at about λ_max = 390 nm in CHCl₃ and 400 nm in film state, and fluoresced at about λ_max = 417 nm in CHCl₃ and 430 nm in the thin film state. Energy gaps between highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) of them were about 2.9 eV, and the energy levels of LUMO situated lower than that of corresponding polycarbazole. Polymer light‐emitting diode devices having configuration of indium tin oxide/poly(3,4‐ethylenedioxythiophene)‐poly(styrenesulfonate)/polymer/CsF/Al using the copolycondensates, poly(N‐arylcarbazole‐2,7‐diyl), and poly(9,9‐dialkylfluorene‐2,7‐diyl), emitted bluish EL at operating voltages lower than 7 V. The device embedded the random copolycondensate showed notably higher performance with maximum luminance of 31,200 cd m^?2 at 11.0 V, and the current efficiencies observed under operating voltages lower than 7 V were higher than those of the other devices. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Simple synthesis,photophysics, and electroluminescent properties of poly[2,7‐bis(4‐tert‐butylstyryl)fluorene‐9, 9‐diyl‐alt‐alkane‐α,ω‐diyl]

A simple synthetic route was used for the synthesis of a novel series of alternating copolymers based on substituted 2,7‐distyrylfluorene bridged through alkylene chains. First, 2,7‐dibromofluorene was reacted with 2 equiv of butyllithium, and this was followed by a treatment with 1 equiv of α,ω‐dibromoalkane to yield the intermediate, poly(2,7‐dibromofluorene‐9,9‐diyl‐alt‐alkane‐α,ω‐diyl). ( 1 ) Heck coupling of the latter with 1‐tert‐butyl‐4‐vinylbenzene afforded the target, poly[2,7‐bis(4‐tert‐butylstyryl)fluorene‐9,9‐diyl‐alt‐alkane‐α,ω‐diyl] ( 2 ). The two versions of 2 ( 2a and 2b which have hexane and decane, respectively, as alkane groups) were readily soluble in common organic solvents. Their glass‐transition temperature was relatively low (52 and 87 °C). An intense blue photoluminescence emission with maxima at about 408 and 409 nm was observed in tetrahydrofuran solutions, whereas thin films exhibited an orange emission with maxima at 569 and 588 nm. Very large redshifts of the photoluminescence maxima and Stokes shifts in thin films indicated strong aggregation in the solid state. Both polymers oxidized and reduced irreversibly. Single‐layer light‐emitting diodes with hole‐injecting indium tin oxide and electron‐injecting aluminum electrodes were fabricated. They emitted orange light with external electroluminescence efficiencies of 0.52 and 0.36% photon/electron, as determined in light‐emitting diodes made of 2a and 2b , with alkylenes of (CH₂)₆ and (CH₂)₁₀, respectively. An increase in the external electroluminescence efficiency up to 1.5% was reached in light‐emitting diodes made of polymer blends consisting of 2a and poly(9,9‐dihexadecylfluorene‐2,7‐diyl), which emitted blue‐white light. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 809–821, 2007.     

Copolymerization of Azobenzene-bearing Monomer and 3,4-Ethylenedioxythiophene(EDOT): Improved Electrochemical Performance for Electrochromic Device Applications

In this study,novel electrochromic copolymers of 3,4-ethylenedioxythiophene(EDOT)and(E)-1,2-bis(2-fluoro-4-(4-hexylthiophen-2-yl)phenyl)diazene(M1)with different monomer feed ratios were designed and synthesized electrochemically.Electrochemical and spectroelectrochemical characterizations were performed using voltammetry and UV-Vis-NIR spectrophotometry techniques to test the applicability of copolymers for electrochromic applications.In terms of electrochemical behaviors,addition of an electron-rich EDOT unit into the azobenzenecontaining copolymer increased the electron density on the polymer chain and afforded copolymers with very low oxidation potentials at around0.30 V.While the homopolymers(P1 and PEDOT)exhibited neutral state absorptions centered at 510 and 583 nm,EDOT-bearing copolymers showed red shifted absorptions compared to those of P1 with narrower optical band gaps.In addition,the poor optical contrast and switching times of azobenzene-bearing homopolymer were significantly improved with EDOT addition into the copolymer chain.As a result of the promising electrochromic and kinetic preperties,Co P1.5-bearing single layer electrochromic device that works between purple and light greenish blue colors was constructed and characterized.     

Poly(ϵ‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ϵ‐caprolactone) triblock copolymers: Synthesis and self‐assembly in aqueous solutions

Nontoxic and biodegradable poly(?‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(?‐caprolactone) triblock copolymers were synthesized by the solution polymerization of ?‐caprolactone in the presence of poly(ethylene glycol). The chemical structure of the resulting triblock copolymer was characterized with ¹H NMR and gel permeation chromatography. In aqueous solutions of the triblock copolymers, the micellization and sol–gel‐transition behaviors were investigated. The experimental results showed that the unimer‐to‐micelle transition did occur. In a sol–gel‐transition phase diagram obtained by the vial‐tilting method, the boundary curve shifted to the left, and the gel regions expanded with the increasing molecular weight of the poly(?‐caprolactone) block. In addition, the hydrodynamic diameters of the micelles were almost independent of the investigated temperature (25–55 °C). The atomic force microscopy results showed that spherical micelles formed at the copolymer concentration of 2.5 × 10^?4 g/mL, whereas necklace‐like and worm‐like shapes were adopted when the concentration was 0.25 g/mL, which was high enough to form a gel. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 605–613, 2007     

Blue to light gray electrochromic polymers from dodecyl‐derivatized thiophene Bis‐substituted dibenzothiophene/dibenzofuran

3‐Dodecylthiophene end‐capped two monomers: 2,8‐bis‐(4‐dodecyl‐thiophen‐2‐yl)‐dibenzothiophene (DBT‐3DTh) and 2,8‐bis‐(4‐dodecyl‐thiophen‐2‐yl)‐dibenzofuran (DBF‐3DTh) were synthesized via Stille coupling reaction. Both monomers exhibited emission peaks at about 400 nm with fluorescence quantum yields ranging from 0.16 to 0.21. The corresponding electroactive polymers poly(2,8‐bis‐(4‐dodecyl‐thiophen‐2‐yl)‐dibenzothiophene) (PDBT‐3DTh) and poly(2,8‐bis‐(4‐dodecyl‐thiophen‐2‐yl)‐dibenzofuran) (PDBF‐3DTh) were obtained by electropolymerization method and displayed good electrochemical stability. Both polymers switched between light gray in the neutral state and blue in the oxidized state. Kinetic investigations showed that PDBT‐3DTh exhibited a maximum optical contrast (ΔT %) of 25.23% at 575 nm with the coloration efficiency (CE) of 196 cm² C^?1. However, the electrochromic properties of PDBF‐3DTh were inferior to PDBT‐3DTh. Further detailed discussions with EDOT and 3‐alkylthiophenes end‐capped DBT/DBF hybrid electrochromic polymers were comparatively studied. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1468–1478