Carbon electrodes modified with ruthenium metallodendrimer multilayers for the mediated oxidation of methionine and insulin at physiological pH

A pentaerythritol-based metallodendrimer with ruthenium(II) terpyridine units, Ru(II)Den, catalyzed the oxidation of L-methionine and insulin at pH 7.0. The Ru(II)Den was immobilized on a carbon surface through layer-by-layer electrostatic deposition; the negatively charged polymer, poly(styrene sulfonate), was its counterpart. These bilayers were assembled on a glassy carbon electrode that was first modified by deposition of a layer of the conjugate base of sulfanilic acid and then with quaternized poly(4-vinylpyridine). Reversible voltammetry for the Ru(II/III) redox couple was observed, the current for which increased linearly with layer number, n, of Ru(II)Den up to n = 12. Cyclic voltammetry was used to demonstrate the mediation of L-methionine oxidation by a Ru(II)Den-containing multilayer assembly. Flow injection amperometric determination of insulin at pH 7.0 at this modified electrode yielded a calibration curve with the following characteristics: linear dynamic range, 6 nM-0.4 microM; sensitivity, 225 nA microM(-1); detection limit (k = 3 criterion), 2 nM. Of particular importance was that the sensitivity was proportional to the number of Ru(II)Den layers.     

Langmuir-Blodgett films from polyaniline/ruthenium complexes as modified electrodes for detection of dopamine

Langmuir-Blodgett (LB) films from mixtures of polyaniline (PANI) and the ruthenium complex mer-[RuCl₃(dppb)(py)] (dppb=PPh₂(CH₂)₄PPh₂; py=pyridine) (Rupy) were used to modify electrodes and to detect dopamine (DA). The electrochemical response has been used as the principle of detection in order to exploit the molecular-level interaction between PANI and Rupy in the LB films. Cyclic voltammograms were performed in a potential range where the Rupy complex is not electroactive and the response is dominated by the interconversion between the oxidation states leucoemeraldine and emeraldine of PANI. In the presence of DA a further redox pair appears at approximately 230 and 0 mV, associated with oxidation/reduction of DA to dopaminequinone. The current increased linearly in the range between 4.0×10⁻⁵ and 1.2×10⁻³ mol/l. The detection limit for DA concentrations for the 21-layer LB film from PANI/Rupy was 4.0×10⁻⁵ mol/l, which is sufficient to detect DA in a pharmaceutical product. The modified electrode based on PANI/Rupy LB films is selective to DA, particularly because the oxidation potential for DA is lowered, in comparison to a bare indium-tin-oxide electrode. The presence of ascorbic acid, which is an important interferent for DA, could be detected when its concentration was three times that of DA.     

Catalytic wet air oxidation of chlorophenols over supported ruthenium catalysts

A series of noble metal (Pt, Pd, Ru) loaded zirconia catalysts were evaluated in the catalytic wet air oxidation (CWAO) of mono-chlorophenols (2-CP, 3-CP, 4-CP) under relatively mild reaction conditions. Among the investigated noble metals, Ru appeared to be the best to promote the CWAO of CPs as far as incipient-wetness impregnation was used to prepare all the catalysts. The position of the chlorine substitution on the aromatic ring was also shown to have a significant effect on the CP reactivity in the CWAO over 3wt.% Ru/ZrO(2). 2-CP was relatively easier to degradate compared to 3-CP and 4-CP. One reason could be the higher adsorption of 2-CP on the catalyst surface. Further investigations suggested that 3wt.% Ru/ZrO(2) is a very efficient catalyst in the CWAO of 2-CP as far as high 2-CP conversion and TOC abatement could still be reached at even lower temperature (393K) and lower total pressure (3MPa). Additionally, the conversion of 2-CP was demonstrated to increase with the initial pH of the 2-CP solution. The dechlorination reaction is promoted at higher pH. In all cases, the adsorption of the reactants and the reaction intermediates was shown to play a major role. All parameters that would control the molecule speciation in solution or the catalyst surface properties would have a key effect.     

Electrogenerative oxidation of dilute sulfur dioxide with gas diffusion electrodes

Oxidation of dilute SO₂ at gas diffusion-type catalytic electrodes, Pt/PTFE and Pt/carbon/PTFE, was studied in electrogenerative cells equipped wit     

Insulin oxidation and determination at carbon electrodes

The redox chemistry of insulin was investigated at glassy carbon (GC) electrodes that were coated with films of chitosan (CHIT) and multiwalled carbon nanotubes (CNT). While bare electrodes deactivated quickly during insulin oxidation, the GC electrodes coated with CHIT and CHIT-CNT films generated stable insulin currents. The GC/CHIT-CNT electrodes were used for investigating the electrooxidation process of insulin and amperometric determination of insulin. The mass spectrometric, electron paramagnetic resonance, and separation studies of electrolyzed insulin solutions suggested that the loss of 4 mass units upon insulin oxidation at CNT could be accounted for by the formation of two dityrosine cross-links intramolecularly. At a potential of 0.700 V and physiological pH 7.40, the GC/CHIT-CNT electrodes displayed a detection limit of approximately 30 nM insulin (S/N = 3), sensitivity of 135 mA M(-1) cm(-2), linear dynamic range from 0.10 to 3.0 microM (R2 = 0.995), and superior operational and long-term stability. The CNT-based electrodes are promising new insulin detectors for diabetes-related studies such as fast chromatographic analysis of therapeutic insulin formulations or evaluation of quality of pancreatic islets prior to their transplantation.     

Flow injection amperometric detection of 2'-deoxyguanosine at a ruthenium oxide hexacyanoferrate modified electrode

A ruthenium oxide hexacyanoferrate (RuOHCF) modified electrode was developed. Hydrodynamic voltammetry was employed to demonstrate the remarkable electrocatalytic activity toward the oxidation of 2'-deoxyguanosine. The RuOHCF modified electrode was used as amperometric detector for 2'-deoxyguanosine determination in a FIA apparatus. The influence of various experimental conditions was explored for optimum analytical performance, and at these experimental conditions, the method exhibited a linear response range to 2'-deoxyguanosine extending from 3.8 to 252 micromol L(-1) with detection limit of 94 nmol L(-1). Applications in DNA samples were examined, and the results for determination of 2'-deoxyguanosine were in good agreement with those obtained by HPLC analysis. Studies on the kinetics of the in vitro consumption of 2'-deoxyguanosine by acetaldehyde were also performed.     

Enhanced electrochemical oxidation of methanol on copper electrodes modified by electrocorrosion and electrodeposition

In this paper, we report a study of electrocatalytic oxidation of methanol on copper electrodes subjected to different surface treatments, either electrocorrosion or electrodeposition in the absence of strong hydrogen co-deposition. The surface morphology of treated electrodes was examined by Field Emission Scanning Electron Microscopy (FE-SEM). The effect of different treatment conditions and the methanol concentration dependence were evaluated by cyclic voltammetric technique. The results indicate that the oxidation of methanol can be enhanced by a suitable micro and nano structure generated by these treatments. This enhanced electrode activity is related to an increase of the effective surface area and/or to an increase of the surface concentration of electroactive molecules or intermediates.     

Photoelectrochemical reactions of electrodes modified with composites between conjugated polymer or ruthenium complex and single-walled carbon nanotubes

Composite materials between conjugated polymer; poly[2-methoxy-5-(2'-ethylhexyloxy)-1.4-phenylene vinylene] (MEHPPV), or ruthenium(II)-tris(2,2'-bipyridine) (Ru(bpy)₃²⁺)-poly(sodium 4-styrenesulfonate) (PSS) complex and single-walled carbon nanotubes (SWNTs) were fabricated using polymer wrapping method. Formation of SWNT/MEHPPV or SWNT/PSS/Ru(bpy)₃²⁺ composite was confirmed by absorption and fluorescence spectra, and AFM images. Electrode modified with SWNT/MEHPPV or SWNT/PSS/Ru(bpy)₃²⁺ composite was prepared by casting from DMF solution of SWNT/MEHPPV or aqueous solution of SWNT/PSS/Ru(bpy)₃²⁺. The electrode modified with SWNT/MEHPPV or SWNT/PSS/Ru(bpy)₃²⁺ composite showed photocurrent response due to photoexcitation of MEHPPV or Ru(bpy)₃²⁺. The photocurrents are ascribed to photoinduced electron-transfer reaction from excited state of MEHPPV or Ru(bpy)₃²⁺ to SWNT.     

Synthesis and characterization of ruthenium dioxide nanostructures

We report the synthesis of ruthenium dioxide (RuO₂) nanostructures by thermal evaporation of RuO₂ powder. RuO₂ nanostructures of different shapes were synthesized at various concentration, flow rate, and pressure of oxygen. At a constant pressure of 3 torr of flowing oxygen, polygonal prism-like RuO₂ nanorods with flat tips were grown at an O₂ flow rate of 100 sccm; club-shaped nanorods with obelisk tip were formed at 300 and 600 sccm, and hollow rods with square tip were formed at 1800 sccm. A mixture of O₂ and Ar at a total flow rate of 600 sccm led to the formation of short club-shaped nanorods indicating the suppression effect of Ar on the growth of nanorods. The pressure also had a significant effect on the formation of RuO₂ nanostructures, at a fixed flow rate of 600 sccm of O₂, a pressure of 3 torr resulted in the growth of club-shaped RuO₂ nanorods, while high pressures of 380 and 760 torr resulted in the formation of both linear club-shaped and pine tree-like hierarchical RuO₂ nanorods. X-ray diffraction and transmission electron microscopy analysis indicated the formation of tetragonal phase of RuO₂ with high crystallinity. A density functional calculation on RuO₂, RuO₃, and RuO₄ was performed to help to explain the experimental results.     

Electrochemical oxidation of histamine and serotonin at highly boron-doped diamond electrodes

The electrochemistry of histamine and serotonin in neutral aqueous media (pH 7.2) was investigated using polycrystalline, boron-doped diamond thin-film electrodes. Cyclic voltammetry, hydrodynamic voltammetry, and flow injection analysis (FIA) with amperometric detection were used to study the oxidation reactions. Comparison experiments were carried out using polished glassy carbon (GC) electrodes. At diamond electrodes, highly reproducible and well-defined cyclic voltammograms were obtained for histamine with a peak potential at 1.40 V vs SCE. The voltammetric signal-to-background ratios obtained at diamond were 1 order of magnitude higher than those obtained for GC electrodes at and above 100 microM analyte concentrations. A linear dynamic range of 3-4 orders of magnitude and a detection limit of 1 microM were observed in the voltammetric measurements. Well-defined sweep rate-dependent voltammograms were also obtained for 5-hydroxytryptamine (5-HT). The characteristics of the voltammogram indicated lack of adsorption of its oxidation products on the surface. No fouling or deactivation of the electrode was observed within the experimental time of several hours. A detection limit of 0.5 microM (signal-to-noise ratio 13.8) for histamine was obtained by use of the FIA technique with a diamond electrode. A remarkably low detection limit (10 nM) was obtained for 5-HT on diamond by the same method. Diamond electrodes exhibited a linear dynamic range from 10 nM to 100 microM for 5-HT determination and a range of 0.5-100 microM for histamine determination. The FIA response was very reproducible from film to film, and the response variability was below 7% at the actual detection limits.     

Electrochemical oxidation of oxalic acid at highly boron-doped diamond electrodes

Electrochemical oxidation of oxalic acid has been investigated at bare, highly boron-doped diamond electrodes. Cyclic voltammetry and flow injection analysis with amperometric detection were used to study the electrochemical reaction. Hydrogen-terminated diamonds exhibited well-defined peaks of oxalic acid oxidation in a wide pH range. A good linear response was observed for a concentration range from 50 nM to 10 microM, with an estimated detection limit of approximately 0.5 nM (S/N = 3). In contrast, oxygen-terminated diamonds showed no response for oxalic acid oxidation inside the potential window, indicating that surface termination contributed highly to the control of the oxidation reaction. An investigation with glassy carbon electrodes was conducted to confirm the surface termination effect on oxalic acid oxidation. Although a hydrogen-terminated glassy carbon electrode showed an enhancement of signal-to-background ratio in comparison with untreated glassy carbon, less stability of the current responses was observed than that at hydrogen-terminated diamond.     

Electrothermal flow on electrodes arrays at physiological conductivities

AC electrothermal (ET) flow is inevitable for microfluidic systems dissipating electric energy in a conducting medium. Therefore, many practical applications of biomicrofluidics are prone to ET flow. Here, a series of observations are reported on ET flow in a microfluidic chamber that houses three electrode pairs. The observations indicate that the variations in liquid conductivity and channel height critically impact the structure and magnitude of the flow field. Observations indicate that after a critical conductivity a global ET flow is present in the chamber, while at lower conductivities a vortex is present at every electrode edge. In addition, no ET flow is observed when the chamber height is kept below a critical value at physiological conductivity (∼1.5 S/m). The experimental observations are compared with the numerical simulations of ET flow. The validity of the assumptions made in the current AC ET flow theory is also discussed in the light of the experimental data. The observations can be critical while designing microfluidic systems that involve power dissipation in conductive fluids.Inspec keywords: bioelectric phenomena, microfluidics, numerical analysis, bioMEMSOther keywords: electrode array, physiological conductivity, AC electrothermal flow, microfluidic system, electric energy, biomicrofluidics, microfluidic chamber, liquid conductivity, flow field structure, flow field magnitude, global ET flow, ET flow numerical simulation, AC ET flow theory, power dissipation, conductive fluid     

Practically modified attenuated total reflection surface-enhanced IR absorption spectroscopy for high-quality frequency-extended detection of surface species at electrodes

A practically modified ATR configuration has been proposed for in situ electrochemical surface-enhanced IR absorption spectroscopy (SEIRAS) by sandwiching an ultrathin water interlayer between a hemicylindrical ZnSe prism and a Si wafer as an integrated window. This new ATR optics significantly enhances the throughput of an effective IR beam across the ZnSe/gap/Si/metal film, enabling high-quality spectral fingerprints down to 700 cm(-1) to be readily detected at larger incidence angles without compromising the electrochemical feasibility and stability of metallic films deposited on Si. The advantages of this modified ATR-SEIRAS have been initially applied to explore two selected systems: wide-ranged in situ ATR-SEIRA spectra provided strong evidence in support of the formate intermediate pathway for methanol electrooxidation at the Pt electrode in an acid solution; in addition, new spectral fingerprints revealed comprehensive orientational information about of the p-nitrobenzoate species at Pt electrode as a result of the dissociative adsorption of p-nitrobenzoic acid molecules from an acid solution.     

Electrochemical detection of carbamate pesticides at conductive diamond electrodes

Conductive boron-doped diamond thin-film electrodes were used for the electrochemical detection of selected N-methylcarbamate pesticides (carbaryl, carbofuran, methyl 2-benzimidazolecarbamate, bendiocarb) after liquid chromatographic separation. Two kinds of detection methods were adopted in this study. In the first method, a direct detection of underivatized pesticides was carried out at an operating potential of 1.45 V versus Ag/AgCl, which resulted in the detection limits of 5-20 ng/mL (or 5-20 ppb) with S/N = 2 due to the low background current and wide potential window of the diamond electrode. In the second method, the detection limits were improved by subjecting the pesticide samples to alkaline hydrolysis in a separate step prior to injection. The phenolic derivatives obtained by alkaline hydrolysis oxidize at a relatively lower potential (0.9 V vs Ag/AgCl), which increases the sensitivity drastically. The advantage of the diamond electrode for the detection of phenolic derivatives is that it offers excellent stability in comparison to other electrodes. This method gives the detection limits of 0.6-1 ng/mL (or 0.6-1 ppb), which are well below the maximum residue levels allowed for carbaryl, carbofuran, and bendiocarb. While the lowest detection limits (LOD) obtained by the direct detection of pesticides are comparable to the those reported by the well-established HPLC-fluorescence, the LODs of the alkaline hydrolysis method are found to be even lower than the reported limits. On-line reactivation of the diamond electrode surface was shown to be possible by an anodic treatment of the electrode at approximately 3 V for 30 min in case of electrode fouling, which may occur after a prolonged use. Such a treatment damages the glassy carbon (GC) and metal electrodes, while the diamond electrode remains stable. These results suggest that the diamond electrode is superior to the other previously used electrodes such as GC and Kelgraf type for highly sensitive and stable detection of carbamate pesticides.     

Electrocatalytic tetracycline oxidation at a mixed-valent ruthenium oxide--ruthenium cyanide-modified glassy carbon electrode and determination of tetracyclines by liquid chromatography with electrochemical detection

Mixed-valent films of ruthenium oxide-ruthenium cyanide were electrodeposited onto glassy carbon and characterized for the electrocatalytic oxidation of tetracycline. The currents produced by tetracycline were higher than from previously reported electrode modifications or pretreatments. In H(2)SO(4) pH 1.0 + 0.5 M K(2)SO(4), the second-order rate constant for the reaction between tetracycline and the Ru(III/IV) couple of ruthenium oxide was 3 x 10(5) +/- 1 x 10(5) mol(-1) cm(3) s(-1), and the rate of charge diffusion through the films was 4.5 x 10(-7) +/- 3.5 x 10(-7) cm(2) s(-1). Reaction was localized at the film-solution interface. When used as detectors in liquid chromatography (in H(3)PO(4) pH 2.5 + 0.1 M KH(2)PO(4) + 20% CH(3)CN, E = 1.10 V vs SCE), the electrodes gave limits of detection (>3 S/N) of 0.1 ppm for tetracycline and oxytetracycline and 0.5 ppm for doxycycline and chlorotetracycline. These limits were suitable for FDA and Codex Alimentarius guidelines for tetracyclines in food. Recoveries of the four tetracyclines from sea and freshwater shrimp were in the range 73-111%, which was higher or similar to the previously reported recoveries from shrimp.