13Cr超级马氏体不锈钢热压缩变形行为与组织演变

通过Gleeble-3500热模拟试验机对13Cr超级马氏体不锈钢进行单道次压缩变形试验,系统研究变形温度在950~1150 ℃、应变速率为0.001~10 s^-1条件下的热变形行为。利用双曲正弦模型建立了13Cr超级马氏体不锈钢的流变应力本构方程,求得试验钢的热变形激活能为412 kJ/mol,并基于动态材料模型(DMM)理论绘制了材料的热加工图,得出材料的最佳热变形工艺参数窗口为:变形温度1032~1072 ℃,应变速率0.039~0.087 s^-1。组织演变结果表明,试验钢在高变形温度和低应变速率的条件下,容易发生动态再结晶。当应变速率一定时(0.01 s^-1),变形温度从950 ℃升到1050 ℃,动态再结晶的体积分数从18.7%升高到60.1%,组织的再结晶程度提高,晶粒均匀细小;当变形温度一定时(1050 ℃),随着应变速率的降低,动态再结晶的晶粒长大粗化。     

铸态耐热合金CN617热变形行为研究

用Gleeble-3800热模拟试验机研究了铸态耐热合金CN617退火后在形变温度1050~1180 ℃,应变速率0.01~10 s^-1条件下的热变形行为,建立了该合金的热变形本构方程,绘制了热加工图。结果表明：在形变温度1050~1180 ℃,应变速率0.01~1 s^-1条件下,CN617合金的热变形曲线呈现稳态的流变应力;当在形变温度1100~1180 ℃,应变速率10 s^-1条件下,其热变形行为表现为持续硬化+动态软化过程。CN617合金热变形的热激活能平均为502.35 kJ/mol。在形变温度1050~1125 ℃,应变速率0.2~10 s^-1时形成流变失稳。其原因是动态再结晶程度较低,流变应力较高。     

Incoloy901合金的热加工图与热变形行为

利用Gleeble-3800热模拟机研究Incoloy901高温合金在变形温度950~1150 ℃,应变速率0.005~1 s^-1,真应变0.6下的热变形行为。结果表明:变形温度大于1000 ℃,应变速率大于0.01 s^-1时,Incoloy901合金真应力-应变曲线呈现动态再结晶特征。根据应力-应变曲线构建Incoloy901合金的本构方程与热加工图,得出形变激活能Q=439.401 kJ/mol,最佳热加工工艺为:变形温度1050~1150 ℃,应变速率0.005~0.1 s^-1,在此工艺范围内合金的高温变形功率耗散系数η较高,可达37%,能获得较好的动态再结晶组织。     

DH780钢的热变形行为及热加工图

采用Thermecmastor-Z热模拟试验机研究了试验钢在800~1150 ℃、应变速率0.01~10 s^-1的热压缩变形行为,并观察变形后显微组织。基于试验数据分析,确定了试验钢在奥氏体区的热变形方程,建立试验钢在0.8真应变下的热加工图。结果表明:试验钢的流变应力和峰值应变随变形温度的升高而减小;试验钢在奥氏体区的热变形激活能为385.91 kJ/mol。根据试验钢功率耗散及流变失稳判据确定最佳热加工工艺参数为热变形温度范围1050~1150 ℃和应变速率0.01~0.1 s^-1。在该范围内,试验钢发生完全动态再结晶,功率耗散系数为17%~32%。     

微合金元素Nb对高碳合金钢动态再结晶行为的影响

为研究微合金元素Nb对高碳合金钢动态再结晶行为的影响,利用Gleeble-3500热模拟试验机进行单道次压缩试验,测定了高碳合金钢在变形温度为950~1150 ℃、应变速率为0.01~5 s^-1的流变应力曲线,利用Zeiss光学显微镜观察了奥氏体动态再结晶晶粒形态,通过回归计算获得了相应的再结晶激活能,建立了热变形方程。结果表明:较高的变形温度和较低的应变速率有利于含铌高碳合金钢发生动态再结晶;含铌高碳合金钢的动态再结晶晶粒尺寸随着变形温度的升高而增大,当变形温度为1050 ℃时,含铌高碳合金钢已大量出现动态再结晶晶粒;0.040%铌加入到高碳合金钢中,在应变速率为0.1 s^-1,变形温度为1150 ℃时推迟了钢的动态再结晶开始时间约2.23 s,动态再结晶形变激活能增加了52.26 kJ/mol。     

17Cr2Ni2MoVNb和20Cr2Ni4A齿轮钢的动态再结晶行为及热加工图

利用Gleeble-3800热模拟试验机得到17Cr2Ni2MoVNb和20Cr2Ni4A齿轮钢在1000~1150 ℃、0.01~10 s^-1的流变应力曲线,构建了两种钢的动态再结晶Avrami动力学模型和热加工图。结果表明,两种钢在高变形温度、低应变速率下易发生动态再结晶。17Cr2Ni2MoVNb钢中较高的Nb和Mo含量对动态再结晶的抑制作用大于20Cr2Ni4A钢中的高Ni含量的影响,导致在相同的热变形条件下17Cr2Ni2MoVNb钢的动态再结晶体积分数小于20Cr2Ni4A钢。17Cr2Ni2MoVNb钢的最佳热加工工艺参数为:温度为1050~1150 ℃、应变速率为0.1~0.6 s^-1;20Cr2Ni4A钢的最佳加工参数为:温度为1100~1150 ℃、应变速率为3.3~5.5 s^-1。     

两种冶炼工艺下A286高温合金的热变形行为

为了探究真空感应+真空自耗(VIM+VAR)和电炉+精炼+真空自耗(EAF+LF+VAR)两种工艺冶炼A286高温合金的热变形行为,利用Gleeble-3800热模拟试验机在温度950~1150 ℃和应变速率0.01~10 s^-1范围内进行热压缩试验。基于摩擦和绝热加热修正后的真应力-真应变曲线和应变硬化率曲线建立了A286合金的Arrhenius本构方程,确定了VIM+VAR合金和EAF+LF+VAR合金的热激活能分别为358.15和372.54 kJ·mol^-1。利用临界应变和动态再结晶体积分数50%应变引入动态再结晶速度参数k_v,建立新的动态再结晶模型。采用Prasad 准则绘制两种钢在应变0.2、0.5和0.9下的热加工图,并结合组织分析,确定VIM+VAR合金的最佳热加工工艺条件为1050~1100 ℃,0.01~1 s^-1和1100~1150 ℃,0.1~10 s^-1;EAF+LF+VAR合金的最佳热加工工艺条件为1050~1100 ℃,0.01~1 s^-1和1100~1150 ℃,0.1~3 s^-1,得出VIM+VAR合金的热加工区间较宽,其热加工性能优于EAF+LF+VAR合金。     

22Cr-32Fe-40Ni合金热变形行为

采用Gleeble-3800热模拟试验机对22Cr-32Fe-40Ni合金在变形温度为950～1150℃、应变速率为0.1～10 s^-1范围内进行了热模拟压缩试验，对材料在热变形过程中的流变特性和组织演变规律进行了研究。结果表明，在变形温度高于1000℃或应变速率小于1 s^-1时，材料的硬化效应和软化效应达到动态平衡；在变形温度低于1000℃或应变速率为10 s^-1时，材料以动态再结晶为主的软化效应占主导作用。通过应变硬化率曲线确定了动态再结晶临界条件，基于温度补偿Arrhenius方程建立了22Cr-32Fe-40Ni合金的热变形本构方程，热变形激活能Q为438.339 kJ·mol^-1。22Cr-32Fe-40Ni合金适宜的热加工区间为变形温度1040～1150℃,应变速率0.1～0.47 s^-1。     

100Cr6轴承钢的热变形行为及热加工图

采用Gleeble-3500热模拟试验机研究了100Cr6轴承钢在变形温度为850～1150℃、应变速率为0.01～10 s~(-1)条件下的热变形行为。分析了应变速率和变形温度对流变应力的影响,建立了100Cr6轴承钢热变形时的本构方程和热加工图,并讨论了组织变化情况。结果表明,在相同的应变速率下,流变应力随着温度的升高而降低;而在相同的变形温度下,流变应力随着应变速率的升高而增大。当应变速率为0.1 s~(-1)时,在850℃和950℃压缩变形时,发生了动态回复软化;而在1050℃和1150℃热压缩变形时,加工硬化的软化机理为动态再结晶。结合显微组织观察,得到变形温度950～1150℃、应变速率0.01～0.1 s~(-1)为100Cr6钢的合理热加工工艺参数。     

低碳Ti-Mo微合金马氏体钢的热变形行为

利用Gleeble-3800热模拟试验机对试验钢在950~1100 ℃,应变速率为0.1~5.0 s^-1,最大应变量为60%的条件下进行了热压缩模拟试验。结果表明：高变形温度、低应变速率和大变形量有利于动态再结晶,试验在1050 ℃、变形量60%、变形速率1 s^-1条件下得到圆整均匀再结晶晶粒,平均晶粒尺寸为14.84 μm;推演出低碳Ti-Mo微合金马氏体钢的形变激活能为462.8 kJ/mol及Z参数与动态再结晶变形条件的关系;建立起试验钢动态再结晶临界应变公式ε_c=0.3729Z^0.3496。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

The Mirror with Patterns of Auspicious Animals and Grapes——Exquisite cast mirror and the technology of surface tin-enrichment by rubbing-in and infiltration of tin-rich powder

<正>Bronze mirrors were used by the Chinese people before the introduction of the glass mirror.Only after it was replaced by the glass mirror did the bronze mirror gradually retreat from people's lives.Different styles of bronze mirrors were made in different historical periods,particularly in the Warring States Period,the Han and Tang Dynasties,which were the three peaks of the development of bronze mirror arts in ancient China.The casting techniques were exquisite.The surface of the bronze mirror was smooth and bright enough to reflect one's image,and there were scarcely any casting defects on the mirror surface.On the back of the bronze mirror,there were rich depictions of Arts and Humanities,and the ornamentations were also     

The 9th China International Diecasting Congress & Exhibition

The 9th China International Diecasting Congress ＆ Exhibition was held on July 22-24, 2014 at Shanghai New International Expc Centre. This exhibition was the most successful over the years, with over 6890 visitors and 155 exhibitors, and the exhibition area increased by 30% from 9,500 square meters in 2012 to 12340 square meters. Die casting enterprises from a total of 24 countries and regions, including China mainland, Chinese Taiwan and Hong Kong, South Korea, Japan, Germany, India, Thailand, Malaysia, the United States, Russia, Australia, Iran, Ukraine, Brazil, Colombia, Singapore, Austria, Canada, Croatia, France, Turkey, United Kingdom, Vietnam, attended the congress and exhibition.     

Introduction of the Fluid Control Engineering Institute of Kunming University of Science and Technology

正The Fluid Control Engineering Institute of Kunming University of Science and Technology was set up in 1996.The researches of institute concentrate on electro-hydraulic(pneumatic)servo/proportional control and hydromechatronics.The Institute is committed to research and development of electro-hydraulic control of high-end technical equipment in ferrous metallurgy refining produc-     

RARE METALS Volume Contents

正~~     

Antimony Induced Crystallization of Amorphous Silicon

Antimony induced crystallization of PVD (physics vapor deposition) amorphous silicon can be observed on sapphire substrates. Very large crystalline regions up to several tens of micrometers can be formed. The Si diffraction patterns of the area of crystallization can be observed with TEM (transmission electron microscopy). Only a few and much smaller crystals of the order of 1μm were formed when the antimony layer was deposited by MBE (molecular beam epitaxy) compared with a layer formed by thermal evaporation. The use of high vacuum is essential in order to observe any Sb induced crystallization at all. In addition it is necessary to take measures to limit the evaporation of the antimony.     

A CUMULATIVE FATIGUE DAMAGE RULE UNDER THE ALTERNATIVE OF CORROSION OR CYCLIC LOADING

Fatigue damage increases with the applied loading cycles in a cumulative manner and the material deteriorates with the corrosion time. A cumulative fatigue damage rule under the alternative of corrosion or cyclic loading was proposed. The specimens of aluminum alloy LY12-CZ soaked in corrosive liquid for different times were tested under the constant amplitude cyclic loading to obtain S-N curves. The test was carried out to verify the proposed cumulative fatigue damage rule under the different combinations among corrosion time, loading level, and the cycle numbers. It was shown that the predicted residual fatigue lives showed a good agreement with the experimental results and the proposed rule was simple and can be easily adopted.