空气节流对超燃燃烧室火焰稳定影响的数值研究

空气节流通过在流场中产生激波串,有效地辅助燃料实现稳定燃烧。非定常数值模拟研究了空气节流对超燃燃烧室燃料稳定燃烧的影响,分析了节流实现燃料稳定燃烧的机理。结果表明:在燃烧室入口马赫数2、静温548.8K、静压0.1MPa,乙烯燃料当量比为0.5,先锋氢辅助点火的条件下,距离发动机入口845mm处,30%入口空气流量的节流流量有效地实现了燃料的稳定燃烧,激波串是实现燃料稳定燃烧的根本原因,节流参数对节流效果有着较大的影响。     

空气节流对超燃冲压发动机燃烧室起动点火影响的数值研究

利用空气节流在流场中产生激波串,有效地辅助燃料实现起动点火.非定常Navier-Stokes方程数值模拟研究了空气节流对超燃冲压发动机燃烧室起动点火的影响,分析了起动点火时间段(0~1.0ms)内空气节流 对流场参数的影响.数值模拟结果表明:在燃烧室入口马赫数为2.0、静温为548.8K、静压为101555.9 Pa,乙烯燃料当量比为0.5,先锋氢辅助点火的条件下,距离发动机入口845mm处,节流流量为入口空气流量的30%,有效地实现了发动机的起动点火,无空气节流情况下的发动机点火效果不佳,火焰最终熄灭.      

脉冲燃烧风洞中空气节流对煤油燃料超燃冲压发动机火焰稳定影响研究

采用试验与数值模拟方法研究了空气节流对煤油燃料超燃冲压发动机火焰稳定的影响。发动机入口气流总温、总压和马赫数分别为1100K,1.0MPa和2.0。空气节流位置距离发动机入口625mm,空气节流流量为入口发动机空气流量的27.2%。多种非接触光学测量手段被应用于超燃冲压发动机燃烧流场结构和火焰传播规律的诊断,包括纹影、阴影、差分干涉、自发光照相和OH-PLIF。首先考察了有、无空气节流时超燃冲压发动机冷流流场的结构,结果显示:在实施空气节流后,流场内产生了激波串结构。激波串促使流场的静温和静压升高,马赫数降低。同时激波串与边界层相互作用,导致了边界层分离,促进了燃料与空气的高效混合,实现了煤油的可靠点火。其次考察了先锋氢气燃烧流场的火焰传播规律与稳定形态,结果表明:当先锋氢气当量比为0.3时,燃烧流场振荡;当先锋氢气当量比为0.1时,燃烧流场稳定。最后研究了空气节流对煤油燃料超燃冲压发动机火焰稳定的影响,结果表明:不实施空气节流时,液态室温煤油吹熄了先锋火焰,煤油点火失败;实施空气节流后,煤油成功点火,当先锋氢气和空气节流撤除后,煤油仍然保持稳定的燃烧。     

超燃冲压发动机燃烧室空气节流技术研究

为考察空气节流对超燃冲压发动机燃烧室的影响,非定常数值模拟和地面实验相结合证实了空气节流可以实现超燃燃烧室燃料稳定燃烧,研究了节流位置、节流流量、节流撤去时间对节流效果的影响。结果表明:在燃烧室入口马赫数2,静温548.8K,静压101555.9Pa条件下,745mm处节流时,激波串稳定时间较短,稳焰失败;875mm处节流时,火焰稳定成功。随着节流流量和节流撤去时间的增加,燃烧越来越剧烈,壁面压力逐渐升高,可能影响进气道的起动,对于本文来流条件,30%入口空气流量作为节流流量是合适的,440ms以前撤去空气节流是恰当的。     

空气节流对乙烯燃料超燃冲压发动机流场结构影响研究

空气节流可以有效地实现超燃冲压发动机燃烧室燃料的稳定燃烧,采用非定常数值模拟和地面试验研究了空气节流作用下乙烯燃料超燃冲压发动机的流场特性。结果表明:在燃烧室入口马赫数2、静温530K,静压0.1MPa,845mm处节流条件下,冷流流场达到稳定所需时间较短,约为2ms;在空气节流开始后的6ms注入燃料实现发动机的起动点火是合适的;28ms后燃烧流场稳定,流场呈现短周期的小幅振荡,周期约为0.86ms,振荡对流场的影响很小;壁面压力数据的数值模拟结果与试验结果匹配良好,数值模拟更加全面地给出了流场结构信息。     

正十二烷和甲基环己烷在超燃燃烧室中的点火和稳焰特性研究

主要研究了液态单组份碳氢燃料在超燃燃烧室中的点火和稳焰性能,所用燃料为正十二烷和甲基环己烷,研究结果可以为超燃冲压发动机的燃料制备提供部分依据。试验在以蓄热式加热器为核心的直连式试验台上进行,超燃燃烧室进口总温在1040~1100K范围内,进口马赫数2.03,进口空气流量2.0kg/s左右,点火器为燃气发生器,采用串联凹腔作为火焰稳定装置,在第一个凹腔前常温燃料垂直喷射到燃烧室中。研究结果表明:与正十二烷相比,甲基环己烷在来流总温较低的超声速流中更容易被点燃和实现稳火,但总体来讲,当燃烧室进口总温低于1100K时,常温液态燃料的点火和稳焰性能较差。理论分析了两种燃料的蒸发特性,计算结果表明在来流参数相同时,甲基环己烷的蒸发特性优于正十二烷。利用一维分析方法结合试验测量的壁面静压、燃烧室入口马赫数和空气流量,得到了正十二烷和甲基环己烷不同工况时的总温分布和出口燃烧效率。     

M3条件下乙烯燃料超燃冲压发动机空气节流点火试验

在隔离段入口Ma=3(模拟飞行马赫数6.5)条件下,采用乙烯燃料的超燃冲压发动机点火十分困难。为解决该难题,采用了空气节流作为辅助点火措施。基于脉冲燃烧风洞直连式试验平台进行了空气节流点火试验,通过壁面压力测量,获得了节流点火的火焰发展历程。以点火时间为指标,对节流流量、乙烯当量比、节流时间等参数进行了定量分析,节流流量的调节范围为0%~45%,乙烯当量比调节范围为0.6~1.2,节流时间调节范围为190~350ms。分析了三个节流参数各自的作用机理,通过数据拟合,绘制了节流流量与点火时间、乙烯当量比与点火时间的关系曲线,揭示了节流时间与点火时间的关系。      

空气节流对超燃发动机燃烧性能的影响

为优化隔离段及燃烧室内的流场结构,减小流动速度,提高流道压力,在凹槽稳焰器下游布置空气节流装置,向燃烧室内喷入高压空气,目的是在隔离段建立合适的激波串,以利于点火和火焰稳定.采用CFD方法,对比了无/有空气节流时的冷流流场、燃烧流场,结果表明:节流激波串扩大了低动量区域,激波引起的流动扭曲和较长的驻留时间使得分离流内的空气/燃料混合程度得到显著增强,混合效率由无节流时的40%提高到85%,燃烧效率由无节流时的10%提高到60%.对节流位置和节流量进行了参数化研究,以隔离段入口为坐标原点,分别考察了785,1000,1100mm三个流向节流位置,以及10%,15%,30%三种节流量的影响,结果表明:距离凹槽较近的节流位置对燃烧的影响更为显著,所需节流量更少.30%的节流量将使燃烧室背压急剧提高,引起流动壅塞.研究表明在785mm的流向节流位置采用15%的节流量可获得最好的燃烧性能.      

马赫数4下氢气自燃辅助乙烯点火实验研究

为了研究氢气自燃辅助乙烯点火的具体点火参数和点火性能,在直连式脉冲燃烧风洞设备上进行了模拟飞行马赫数4条件下的超燃发动机乙烯点火试验,试验来流的总温935K,总压0.8MPa,隔离段入口马赫数2.1。试验利用不同质量流量的引导氢气自燃辅助点火,成功实现了乙烯燃料的点火和稳定燃烧。通过流场显示和壁面压力测量发现:(1)能够成功点火的引导氢气流量范围为 0.43~12.61g/s,相当于当量比0.005~0.142;(2)0.43g/s流量氢气注入燃烧室后10ms以内被点燃,乙烯燃料注入后经过了约20ms才被点燃,点火的主要位置为凹槽内;(3)6.68g/s的氢气注入燃烧室后20ms才被点燃,乙烯燃料注入后约8ms即被点燃,点火的主要位置为凹槽下游和凹槽出口位置;(4)点火试验中火焰能够在凹槽内和剪切层内向上游逆传;(5)凹槽下游和下壁面的燃烧,是促进凹槽内燃烧、提升燃烧室压力和引起燃烧室压力震荡的主要原因。      

气化煤油与乙烯超声速燃烧特性对比

为了研究燃料成分变化对超燃冲压发动机燃烧特性的影响,以气化RP-3(中国3#航空煤油)和乙烯为燃料进行了一系列直连式燃烧试验。模型燃烧室入口参数为Ma=2.92,3.46,总温Tt=1430K。基于点火延迟时间、燃烧室壁面静压分布、推力增益和比冲,对比分析了两种燃料的超声速燃烧特性。结果表明,化学活性更高的乙烯比气化煤油具有更高的燃烧性能和燃料利用效率;Ma=2.92,当量比φ≈0.60和1.06时,乙烯的比冲比气化煤油分别约高15%和7.2%;当Ma增加到3.46时,相当的当量比下乙烯和气化煤油之间的比冲差距稍有扩大,约为18%和9.6%。燃烧室入口马赫数和当量比等工况参数对发动机燃烧特性有显著影响。燃料成分对发动机燃烧特性的影响随当量比的提高而弱化,但对燃烧室入口马赫数不敏感。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.