真空退火对355nm Al2O3/MgF2高反射薄膜性能的影响

 采用电子束蒸发沉积技术制备了355nm Al₂O₃/MgF₂ 高反射薄膜，并在真空中进行不同温度梯度的退火，用X射线衍射（XRD）观察了薄膜微结构的变化，用355nm Nd：YAG脉冲激光测试了薄膜的激光损伤阈值，用Lambda 900光谱仪测试了薄膜的透过和反射光谱。结果表明在工艺条件相同的条件下真空退火过程对薄膜的性能有很大的影响，退火温度梯度越小的样品，吸收越小，阈值越大，并且是非晶结构。选择合适的真空退火过程可以减少355nm Al₂O₃/MgF₂ 高反射膜的膜层吸收，提高薄膜的激光损伤阈值。     

HfO_2单层膜的吸收和激光损伤阈值测试

薄膜吸收是降低膜层激光损伤阈值的重要原因,为了研究薄膜吸收对激光损伤阈值的影响,对HfO2单层膜在1 064 nm处的吸收及其在不同波长激光辐照下的损伤阈值进行了测试和分析。研究结果表明:薄膜的激光损伤阈值由薄膜吸收平均值(决定于薄膜中缺陷的种类和数量)和吸收均匀性(决定于薄膜中缺陷的分布)共同决定;根据HfO2单层膜在1064 nm波长处的吸收值,不但可以定性判断薄膜在1 064 nm波长,而且还可以判断在其它波长激光辐照下的抗激光损伤能力。     

1 053，527，351 nm倍频分离膜的制备与性能研究

 用电子束蒸发及光电极值监控技术在石英基底上沉积了三倍频分离膜，将部分样品置空气中于250 ℃温度下进行3 h热退火处理。然后用Lambda900分光光度计测量了样品的光谱性能；用表面热透镜技术测量了样品的弱吸收值；用调Q脉冲激光装置测试了样品分别在355 nm和1 064 nm的抗激光损伤阈值。实验结果发现，样品的实验光谱性能良好，退火前后其光谱性能几乎没有发生温漂，说明薄膜的温度稳定性好；同时弱吸收平均值从退火前的1.07×10^-4下降到退火后的6.2×10^-5，从而使对基频的抗激光损伤阈值提高，从14.6 J/cm²上升到18.8 J/cm²，但是三倍频阈值在退火后有显著降低，从7.5 J/cm²下降到2.5 J/cm²。     

紫外Sc_2O_3薄膜的光学和结构性能表征及其激光作用下的损伤机理

利用电子束蒸发方法,在不同沉积温度(50~350℃)下制备了Sc2O3薄膜。分别用分光光度计,小角掠入射X射线衍射仪和轮廓仪测试了薄膜样品的光谱、微结构和表面粗糙度信息,并用薄膜分析软件Essential Macleod计算了Sc2O3薄膜的折射率和消光系数。结果表明:随着沉积温度升高,Sc2O3薄膜结晶程度增强,晶粒尺寸增大,且较高的沉积温度有利于获得较高的折射率。最后用355 nm,8 ns的三倍频Nd:YAG激光器测试了其激光损伤阈值(LIDT),最大值为2.6 J/cm2,且阈值与薄膜的消光系数、表面粗糙度、光学损耗均呈现相反的变化趋势。用光学显微镜和扫描电子显微镜表征了该薄膜的破坏形貌,详细分析了薄膜在不同激光能量作用下破坏的发展过程,以及Sc2O3薄膜在355 nm紫外激光作用下LIDT与制备工艺的关系,重点分析了355 nm激光作用下薄膜的破坏机理。     

高损伤阈值三倍频分离膜

 设计了Nd：YAG激光用三倍频分离膜,膜层材料为SiO₂和HfO₂。经过优化,膜系在355 nm处的反射率在99%以上,在532 nm和1 064 nm处透射率也在99%以上。采用电子束蒸发技术,在熔融石英基底上制备了样品,经测量,制备的分离膜光学性能与设计值接近。分离膜在355 nm激光辐照下的损伤阈值为5.1 J/cm²,并用微分干涉显微镜表征了薄膜损伤形貌。     

缓冲层对LiB_3O_5晶体上1064nm,532nm倍频增透膜性能的影响

采用电子束蒸发方法在LiB3O5(LBO)晶体上制备了无缓冲层和具有不同缓冲层的1064nm,532nm倍频增透膜。利用Lambda900分光光度计、MTS Nano Indenter纳米力学综合测试系统以及调Q脉冲激光装置对样品的光学性能、附着力和激光损伤阈值进行了测试分析。结果表明,所有样品在1064nm和532nm波长的剩余反射率都分别小于0.1%和0.2%。与无缓冲层样品相比,预镀Al2O3缓冲层的样品的附着力提高了43%,具有Si O2缓冲层的样品的附着力显著提高。激光损伤阈值分析表明,采用Si O2缓冲层改进了薄膜的抗激光损伤性能,但是Al2O3缓冲层的插入却导致薄膜的激光损伤阈值降低。     

两种后处理方法对HfO2薄膜性能的影响

利用电子束蒸发和光电极值监控技术制备了氧化铪薄膜,并分别用两种后处理方法(空气中退火和氧等离子体轰击)对样品进行了处理.然后,对样品的透过率、吸收和抗激光损伤阈值进行了测试分析.实验结果表明,两种后处理方法都能不同程度地降低了氧化铪薄膜的吸收损耗、提高了抗激光损伤阈值.实验结果还表明,氧等离子体轰击的后处理效果明显优于热退火,样品的吸收平均值在氧等离子体后处理前后分别为34.8 ppm和9.0 ppm,而基频(1 064 nm)激光损伤阈值分别为10.0 J/cm2和21.4 J/cm2.     

缓冲层对LBO晶体上1 064 nm,532 nm二倍频增透膜的激光损伤阈值的影响

采用电子束蒸发方法在LBO晶体上制备了无缓冲层和具有不同缓冲层的1 064 nm,532 nm二倍频增透膜.利用Lambda900分光光度计和调Q脉冲激光装置对样品的光学性能和抗激光损伤性能进行了测试分析.结果表明,所有样品在1 064 nm和532 nm波长的剩余反射率都分别小于0.1%和0.2%.与无缓冲层样品相比,采用SiO2和MgF2缓冲层薄膜的激光损伤阈值分别提高了23.1%和25.8%,而Al2O3缓冲层的插入却导致薄膜的激光损伤阈值降低.通过观察薄膜的激光损伤形貌,分析破斑的深度信息和电场分布,表明LBO晶体上1 064 nm,532 nm二倍频增透膜的激光损伤破坏主要表现为膜层剥落,激光产生的热冲击应力使薄膜应力发生很大变化,超过膜层之间的结合而引起膜层之间的分离.采用SiO2或MgF2缓冲层可改进Al2O3膜层的质量,从而有利于提高薄膜的激光损伤阈值.     

缓冲层对LBO晶体上1 064 nm|532 nm二倍频增透膜的激光损伤阈值的影响

采用电子束蒸发方法在LBO晶体上制备了无缓冲层和具有不同缓冲层的1 064 nm,532 nm二倍频增透膜.利用Lambda900分光光度计和调Q脉冲激光装置对样品的光学性能和抗激光损伤性能进行了测试分析.结果表明,所有样品在1 064 nm和532 nm波长的剩余反射率都分别小于0.1％和0.2％.与无缓冲层样品相比,采用SiO2和MgF2缓冲层薄膜的激光损伤阈值分别提高了23.1％和25.8％,而Al2O3缓冲层的插入却导致薄膜的激光损伤阈值降低.通过观察薄膜的激光损伤形貌,分析破斑的深度信息和电场分布,表明LBO晶体上1 064 nm,532 nm二倍频增透膜的激光损伤破坏主要表现为膜层剥落,激光产生的热冲击应力使薄膜应力发生很大变化,超过膜层之间的结合而引起膜层之间的分离.采用SiO2或MgF2缓冲层可改进Al2O3膜层的质量,从而有利于提高薄膜的激光损伤阈值.     

LBO晶体上1064 nm,532 nm二倍频增透膜的制备和性能

采用电子束蒸发方法在三硼酸锂(LBO)晶体上制备了1064 nm,532 nm二倍频增透膜.利用Lambda900分光光度计、MTSNanoIndenter纳米力学综合测试系统以及调Q脉冲激光装置对样品的光学性能、附着力和激光损伤阈值进行了分析测试.结果表明,通过多次实验,不断改进薄膜沉积工艺条件,在LBO晶体上获得了综合性能优异的二倍频增透膜.样品在1064 nm,532 nm波长的剩余反射率分别为0.07%和0.16%,薄膜粘附失效的临界附着力和激光损伤阈值分别为137.4 mN和15.14 J/cm2,薄膜激光损伤发生在Al2O3膜层.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.