一种基于光子晶体光纤的高灵敏度Sagnac型温度传感器建模研究

为提高Sagnac型温度传感器的测温范围和灵敏度，提供了一种具有高双折射高温度灵敏度特性的光子晶体光纤设计方法。通过在光纤空气孔内填充温敏液体材料，使光纤具有良好的温敏特性。在COMSOL中建立该光子晶体光纤的电磁场模型并对光纤特性进行分析计算，利用有限元法分析结构参数对双折射和光纤双折射温度灵敏度的影响，并在所确定结构基础上研究了温敏液体的填充方式和填充液体类型对光纤温敏特性的影响。确定了最优的结构和液体填充方式，最优情况下该光纤的双折射温度灵敏度能够达到2.050 7×10^-5/℃，在1 550 nm处可获得5.96×10^-2的双折射。将2 mm光子晶体光纤应用于Sagnac型温度传感器中并进行传感性能仿真分析，利用多项式拟合的方法对结果数据进行拟合以分析传感器的温度灵敏度，提高拟合准确性、减小测量误差。结果表明在0～75℃范围内传感器平均灵敏度可达11.28 nm/℃，与现有典型Sagnac型温度传感器相比，本文Sagnac型温度传感器在尽量减小光纤长度的基础上获得了较高的温度灵敏度，并且测温范围更大、准确性更高。因此，该传感器在温度测...     

基于低双折射光子晶体光纤Sagnac干涉仪的超低温度系数扭曲传感器

研究了低双折射光子晶体光纤中由光纤扭曲造成的圆双折射效应,并应用Sagnac干涉仪结构设计了扭曲传感器.在Sagnac环中的光子晶体光纤上施加机械压力引入初始线双折射并产生正弦干涉光谱,再扭曲光纤产生圆双折射使干涉光谱随扭曲角度移动.光谱峰值波长随扭曲角度变化符合Sinc函数关系,理论分析与实验相符.传感器灵敏度为1.00 nm/°,分比率为0.01°,并具有超低的温度系数-0.5 pm/℃.     

基于二阶保偏光纤Sagnac环光纤激光器的振动检测研究

提出了一种可用于振动检测的新型光纤光栅传感技术. 用偏振控制器和高双折射保偏光纤构建成Sagnac环, 结合掺铒光纤、单模光纤和隔离器, 形成了单波长光纤激光器, 由粘有光纤Bragg光栅的悬臂梁作为传感探头, 并利用Sagnac环本身的线性边缘, 解调振动信号. 阐述了Sagnac环原理及其产生的边缘效应, 并进行了数值模拟计算, 对振动信号进行了检测实验, 检测系统从L₁到L₁+L₂之间对应的周期可调, 灵敏度高达38.2 μ W/nm, 线性度为0.9996, 动态范围在40–70 dB, 可满足振动传感检测的技术参数要求. 关键词： 光纤光学 振动检测 保偏光纤Sagnac环 光纤激光器     

基于保偏光子晶体光纤的Sagnac干涉温度与应变传感特性

提出一种基于Sagnac干涉原理的光纤传感器,并将其用于温度和应变的环境检测。实验中,选用乙醇溶液填充前后的保偏光子晶体光纤（PM-PCF）作为传感单元。首先,将未填充乙醇溶液的PM-PCF熔接到Sagnac干涉环路中,依靠PM-PCF基底材料的光热效应和光弹性效应,分别在26～50℃温度范围内和0～900μ?应变范围内,实现了-1.72 nm/℃的温度传感灵敏度和35.35 pm/μ?的应变灵敏度。然后,利用氮气加压装置,将乙醇溶液填充到PM-PCF包层空气孔内。这是利用功能材料的外场调谐作用来增强Sagnac干涉仪的传感性能。填充乙醇溶液后,该传感器的温度灵敏度达到-2.66 nm/℃,约为原始PM-PCF温度灵敏度的1.55倍。所提出的用于温度和应变测量的Sagnac干涉传感器结构较为简单,具有良好的迟滞性,对提升光纤传感灵敏度具有一定的借鉴意义。     

基于游标效应的增敏型光纤法布里-珀罗干涉仪温度传感器

本文介绍了一种高灵敏度光纤温度传感器.该传感器由一小段毛细管熔接于单模光纤和一段大模场光纤之间而构成串联的两个法布里-珀罗干涉仪.由于俩干涉仪具有相近的自由光谱区,因而它们的叠加光谱会产生游标效应.实验结果显示,利用游标效应解调,该传感器的温度灵敏度可从单一空气腔法布里-珀罗干涉仪的0.71 pm/℃提高到179.30 pm/℃.该传感器结构紧凑(1 mm)且灵敏度高,具有良好的应用前景.     

基于低双折射光子晶体光纤Sagnac干涉仪的超低温度系数扭曲传感器

研究了低双折射光子晶体光纤中由光纤扭曲造成的圆双折射效应,并应用Sagnac干涉仪结构设计了扭曲传感器.在Sagnac环中的光子晶体光纤上施加机械压力引入初始线双折射并产生正弦干涉光谱,再扭曲光纤产生圆双折射使干涉光谱随扭曲角度移动.光谱峰值波长随扭曲角度变化符合Sinc函数关系,理论分析与实验相符.传感器灵敏度为1....     

基于Sagnac干涉仪的保偏光子晶体光纤氢气传感器

提出了一种基于Sagnac干涉仪的保偏光子晶体光纤(PM-PCF)氢气传感器,建立了传感模型并进行了实验研究和验证。采用对靶磁控溅射技术将钯银(Pd/Ag)合金快速均匀地沉积在保偏光子晶体光纤侧面,并利用Pd吸收氢气后的形变调制保偏光子晶体光纤的双折射,通过测量Sagnac干涉仪输出光谱峰值的变化实现氢气浓度的测量。实验结果表明该传感器可检测的氢气浓度范围为0%~4%,且具有良好的重复性。室温下对低浓度氢气具有较高的灵敏度,氢气浓度由0%变化到1%时的波长偏移量达1.307nm。采用双折射温度不敏感的保偏光子晶体光纤,可很好地抑制外界温度变化对传感器的干扰。     

基于高双折射Sagnac环的可调环形腔掺铒光纤激光器理论与实验研究

报道了一种利用偏振控制器（PC）和保偏光纤（PMF）组成的高双折射Sagnac干涉环实现选频和调谐的环形腔掺铒光纤激光器.理论模拟了PMF和PC对波长的控制作用.实验中调节PC得到了单波长、双波长和多波长激光;并验证了滤波间隔随PMF长度的变化规律.实验中得到了斜率效率20%,3 dB线宽0.016 nm,30 dB线宽0.097 nm,边模抑制比（SMSR）40 dB左右的稳定激光输出. 关键词： 光纤激光器 Sagnac干涉环 环形腔 掺铒光纤     

基于长周期光纤光栅和保偏光纤Sagnac环光谱特性的温度与应变测量研究

提出并研制了一种结构简单、成本低廉的温度与应变同时测量系统,其结构是在保偏光纤Sagnac环内接入一个长周期光纤光栅(LPFG)。利用LPFG对保偏光纤Sagnac环的透射光谱进行调制,通过监测谐振峰波长和强度的变化,发现波长随温度和保偏光纤的应变变化,强度随LPFG的应变变化,因此可以实现温度与应变的区分测量,并且可判断出应变的施加位置。实验得到该系统的温度灵敏度为0.181 81 nm·℃-1,LPFG区的应变灵敏度为0.005 283 dB·με-1,保偏光纤Sagnac环区的应变灵敏度为0.015 72 nm·με-1。实验结果表明该方案可行,并具有一定的实用性。     

监测点波长对高双折射光纤环镜轴向应变灵敏度的影响

研究了高双折射光纤环镜监测点波长对轴向应变灵敏度的影响. 经理论推导得出高双折射光纤环镜轴向应变灵敏度公式. 结果表明: 当高双折射光纤材料选定后, 灵敏度随着监测点波长的增大而增大; 当监测点选定后, 监测点的灵敏度为常数, 波长变化与应变成线性关系. 实验选取不同波长的波峰进行应变灵敏度监测, 对各监测点进行数据拟合, 实验结果与理论分析一致. 研究结果对提高高双折射光纤环镜应变、温度等灵敏度具有指导意义. 关键词： 波长 灵敏度 监测点 高双折射光纤环镜     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.