Structural transformation of layered hydrogen trititanate (H2Ti3O7) to TiO2(B) and its electrochemical profile for lithium-ion intercalation

The thermally-induced structural transformation of layered hydrogen trititanate (H₂Ti₃O₇) to TiO₂(B) has been systematically studied by means of in situ X-ray diffraction (XRD) over a wide temperature range from 170 to 450 °C. Our data indicate a structural transition realized via continuous loss of interlayer water, which results in a series of non-stoichiometric hydrogen titanate compounds (3TiO₂·δH₂O). Electrochemical analysis of hydrogen titanates for lithium-ion intercalation shows that reversible specific capacity increases as calcination temperature increases, whereas cycling stability decreases during the continuous dehydration process.     

Oxygen-releasing step of ZnFe2O4/(ZnO + Fe3O4)-system in air using concentrated solar energy for solar hydrogen production

The oxygen-releasing step of the ZnFe₂O₄/(ZnO + Fe₃O₄)-system for solar hydrogen production with two-step water splitting using concentrated solar energy was studied under the air-flow condition by irradiation with concentrated Xe lamp beams from a solar simulator. The spinel-type compound of ZnFe₂O₄ (Zn-ferrite) releases O₂ gas under the air-flow condition at 1800 K and then decomposes into Fe₃O₄ () and ZnO with a nearly 100% yield (ZnFe₂O₄ = ZnO + 2/3Fe₃O₄ + 1/6O₂). The ZnO was deposited as the thin layer on the surface of the reaction cell wall. A thermodynamic study showed that the ZnO was produced by the reaction between the O₂ gas in the air and the metal Zn vapor generated from ZnFe₂O₄. With the combined process of the present study on the O₂-releasing step and the previous one on the H₂ generation step (ZnO + 2/3Fe₃O₄ + 1/3H₂O = ZnFe₂O₄ + 1/3H₂) for the ZnFe₂O₄/(ZnO + Fe₃O₄)-system, solar H₂ production was demonstrated by one cycle of the ZnFe₂O₄/(ZnO + Fe₃O₄)-system, where the O₂-releasing step had been carried out in air at 1800 K and the H₂ generation step at 1100 K.     

Ag/Al2O3(Li2O)/g-C3N4光催化乙醇制取环氧乙烷

本文制备了一系列Ag/Al₂O₃(Li₂O)/g-C₃N₄复合催化剂,考察了其可见光催化乙醇制取环氧乙烷的性能。Li₂O可调变Al₂O₃表面的酸性,从而降低了主要副产物乙醛的选择性。Ag/Al₂O₃(Li₂O) 在g-C₃N₄上的负载量对产物环氧乙烷的选择性有较大影响,当Ag/Al₂O₃(Li₂O) 负载量为5wt%时,乙醇具有较高的转换率,且环氧乙烷的选择性高达100%。     

Structural,electronic, dynamical and thermodynamic properties of Ca10(PO4)6(OH)2 and Sr10(PO4)6(OH)2: First-principles study

Density functional theory (DFT) with optPBE-vdW functional is used to simulate the structural, electronic, dynamical and thermodynamic properties of Ca₁₀(PO₄)₆(OH)₂(Ca-HA) and Sr₁₀(PO₄)₆(OH)₂(Sr-HA). The calculated structural properties within optPBE-vdW functional is found to yield better agreement with the experimental results, which indirectly suggests the important role of weak hydrogen bond in this crystal. The calculated electronic properties indicate that Ca-HA and Sr-HA are insulator materials with indirect band gap of 5.52 eV and 5.10 eV, respectively. The detailed dynamical properties of two apatites are obtained by the linear-response approach. With replacement of Ca by Sr, the librational mode of OH group decreases from 612 cm^?1 to 569 cm^?1, the stretching mode of OH group increases from 3614.5 cm^?1–3649.9 cm^?1, which is consistent with the experimental results. Finally, some phonon related thermodynamic properties, such as Helmholtz free energy F, internal energy E, entropy S and heat capacity C_V of Sr-HA and Ca-HA are studied according to the phonon calculations within the harmonic approximation. The present calculation results of two apatites with optPBE-vdW functional are in good agreement with the existing experimental.     

Behaviour of AgBi(Cr2O7)2 as a possible cathode for lithium cells

The electrochemical reduction of AgBi(Cr₂O₇)₂ electrodes occurs in a nearly continuous way from 3.5 V to 2 V/Li⁺/Li and leads to a final oxidation state of about III for chromium ions. Three reduction steps can be distinguished:- CR(VI) reduction leading approximately to Cr(V)- Ag(I) reduction to Ag(O)- Further reduction of chromium, leading approximately to CR(III) in a quasi-reversible way.A loss of capacity was observed, however, during repeated charge/discharge cycles.     

Layered GdBa0.5Sr0.5Co2O5+δ as a cathode for intermediate-temperature solid oxide fuel cells

The layered GdBa_0.5Sr_0.5Co₂O_5+δ (GBSC) perovskite oxides are synthesized by Pechini method and investigated as a novel cathode material for intermediate-temperature solid oxide fuel cells (IT-SOFCs). The single cell of NiO–SDC (Sm_0.2Ce_0.8O_1.9)/SDC (20 μm)/GBSC (10 μm) is operated from 550 to 700 °C fed with humidified H₂ as fuel and the static air as oxidant. An open circuit voltage of 0.8 V and a maximum power density of 725 mW cm⁻² are achieved at 700 °C. The interfacial polarization resistance is as low as 0.88, 0.29, 0.13 and 0.05 Ω cm² at 550, 600, 650 and 700 °C, respectively. The ratio of polarization resistance to total cell resistance decreases with the increase in the operating temperature, from 60% at 550 °C to 21% at 700 °C, respectively. The experimental results indicate that GBSC is a promising cathode material for IT-SOFCs.     

Convenient storage of concentrated hydrogen peroxide as a CaO2·2H2O2(s)/H2O2(aq) slurry for energy storage applications

Prior investigations have proposed, and successfully implemented, a stand-alone supply of aqueous hydrogen peroxide for use in fuel cells. An apparent obstacle for considering the use of aqueous hydrogen peroxide as an energy storage compound is the corrosive nature of the nominally required 50 wt.% maximum concentration. Here we propose storage of concentrated hydrogen peroxide in a high weight percent solid slurry, namely the equilibrium system of CaO₂·2H₂O₂(s)/H₂O₂(aq), that mitigates much of the risk associated with the storage of such high concentrations. We have prepared and studied surrogate slurries of calcium hydroxide/water that are assumed to resemble the peroxo compound slurries. These slurries have the consistency of a paste rather than a distinct two-phase (liquid plus solid) system. This paste-like property of the prepared surrogates enable them to be contained within a 200 lines-per-inch. (LPI) nickel mesh screen (33.6% open area) with no solids leakage, and only liquid transport driven by an adsorbent material is placed in physical contact on the exterior of the screen. This hydrogen peroxide slurry approach suggests a convenient and safe mechanism of storing hydrogen peroxide for use in, say, vehicle applications. This is because fuel cell design requires only aqueous hydrogen peroxide use, that can be achieved using the separation approach utilizing the screen material here. This proposed method of storage should mitigate hazards associated with unintentional spills and leakage issues arising from aqueous solution use.     

Photogalvanic behaviour of [Cr2O2S2(1-Pipdtc)2(H2O)2] in aqueous DMF

The photogalvanic behaviour of [Cr₂O₂S₂(1-Pipdtc)₂(H₂O)₂] was performed in a Honda Cell using 100% DMF and different percentages of water-DMF systems. The maximum potential of 200 mV with 18 μA of current was generated in DMF. The experiments were performed at different pH conditions and added dyes. The system was found to generate a maximum potential of 86, 67 and 36 mV at pH∼4, 7 and 8, respectively, at 65 °C. Malachite green and methylene blue (10⁻⁴ M) produced maximum potential of 100 and 82 mV, respectively. The system was reversible when the irradiated solution was aerated immediately. When the solution was kept in dark for a long time (12 h) and then aerated, the solution was found to be irreversible. The Cr(V) is photoreduced to Cr(IV) with the light irradiation and the unstable Cr(IV) reverts to Cr(V) by aerial oxidation.     

Structural and electrochemical properties of Li1+xNi0.5Mn0.5O2+δ (0 ≤ x ≤ 0.7) cathode materials for lithium-ion batteries

A comparative analysis of the properties of LiNi_0.5Mn_0.5O₂ and Li_1+xNi_0.5Mn_0.5O₂ (0.2 ≤ x ≤ 0.7) powders, obtained by the freeze drying method, was performed. Lattice parameters of Li_1+xNi_0.5Mn_0.5O₂ decreased considerably with growing amounts of Li until x = 0.3; at x > 0.5 trace amounts of Li₂MnO₃ are observed by X-ray diffraction (XRD) patterns. X-ray photoelectron spectroscopy (XPS) analysis displayed an increase of Ni³⁺/Ni²⁺ ratio at 0.3 < x < 0.5, while Mn 2p spectra were almost identical in all samples. Rechargeable capacity values (V = 2.5–4.6 V) increased systematically with x reaching its maximum (185–190 mAh g⁻¹) at x = 0.5. Samples with superstoichiometric lithium content also demonstrated good C rate characteristics.     

A modified Al2O3 coating process to enhance the electrochemical performance of Li(Ni1/3Co1/3Mn1/3)O2 and its comparison with traditional Al2O3 coating process

Al₂O₃-modified Li(Ni_1/3Co_1/3Mn_1/3)O₂ is synthesized by a modified Al₂O₃ coating process. The Al₂O₃ coating is carried out on an intermediate, (Ni_1/3Co_1/3Mn_1/3)(OH)₂, rather than on Li(Ni_1/3Co_1/3Mn_1/3)O₂. As a comparison, Al₂O₃-coated Li(Ni_1/3Co_1/3Mn_1/3)O₂ also is prepared by traditional Al₂O₃ coating process. The effects of Al₂O₃ coating and Al₂O₃ modification on structure and electrochemical performance are investigated and compared. Electrochemical tests indicate that cycle performance and rate capability of Li(Ni_1/3Co_1/3Mn_1/3)O₂ are enhanced by Al₂O₃ modification without capacity loss. Al₂O₃ coating can also enhance the cycle performance but cause evident capacity loss and decline of rate capability. The effect of Al₂O₃ coating and Al₂O₃ modification on kinetics of lithium-ion transfer reaction at the interface of electrode/electrolyte is investigated via electrochemical impedance spectra (EIS). The result support that the Al₂O₃ modification increase Li⁺ diffused coefficient and decrease the activation energy of Li⁺ transfer reaction but the traditional Al₂O₃ coating lead to depression of Li⁺ diffused coefficient and increase of activation energy.     

Physical and electrochemical properties of spherical Li1+x(Ni1/3Co1/3Mn1/3)1−xO2 cathode materials

A (Ni_1/3Co_1/3Mn_1/3)CO₃ precursor with an uniform, spherical morphology was prepared by coprecipitation using a continuously stirred tank reactor method. The as-prepared spherical (Ni_1/3Co_1/3Mn_1/3)CO₃ precursor served to produce dense, spherical Li_1+x(Ni_1/3Co_1/3Mn_1/3)_1−xO₂ (0 ≤ x ≤ 0.15) cathode materials. These Li-rich cathodes were also prepared by a second synthesis route that involved the use of an M₃O₄ (M = Ni_1/3Co_1/3Mn_1/3) spinel compound, itself obtained from the carbonate (Ni_1/3Co_1/3Mn_1/3)CO₃ precursor. In both cases, the final Li_1+x(Ni_1/3Co_1/3Mn_1/3)_1−xO₂ products were highly uniform, having a narrow particle size distribution (10-μm average particle size) as a result of the homogeneity and spherical morphology of the starting mixed-metal carbonate precursor. The rate capability of the Li_1+x(Ni_1/3Co_1/3Mn_1/3)_1−xO₂ electrode materials, which was significantly improved with increased lithium content, was found to be better in the case of the denser materials made from the spinel precursor compound. This result suggests that spherical morphology, high density, and increased lithium content were key factors in enabling the high rate capabilities, and hence the power performances, of the Li-rich Li_1+x(Ni_1/3Co_1/3Mn_1/3)_1−xO₂ cathodes.     

High rate cycling performance of Li1.05Ni1/3Co1/3Mn1/3O2 materials prepared by sol-gel and co-precipitation methods for lithium-ion batteries

High rate performance of Li_1.05Ni_1/3Co_1/3Mn_1/3O₂ cathode materials prepared using sol-gel (SG) and co-precipitation (CP) methods were investigated. Scanning electron microscopy results showed that the particle sizes of the materials prepared by SG and CP methods were 300-400 nm and 1-2 μm, respectively. Rate capability tests were performed and compared on these cathode materials with same electrode loading (7 mg cm⁻²). Li_1.05Ni_1/3Co_1/3Mn_1/3O₂ cathode with smaller particle size (SG-nano) demonstrated higher discharge capacity than that of the cathode with larger particle size (CP-micro) at different C-rates. However, upon extended cycling at 1C and 8C, CP-micro showed better capacity retention when compared to that of SG-nano. CP-micro exhibited 95 and 91% where as SG-nano exhibited only 87 and 76%, respectively, at 1C and 8C after 50 cycles. The results showed that the use of nanosized materials was advantageous for obtaining a better rate capability where as the use of microsized materials was beneficial for better capacity retention during extended cycling at high C-rates.     

Iron oxide (n-Fe2O3) nanowire films and carbon modified (CM)-n-Fe2O3 thin films for hydrogen production by photosplitting of water

Iron oxide n-Fe₂O₃ nanowire photoelectrodes were synthesized by thermal oxidation of Fe metal sheet (Alfa Co. 0.25 mm thick) in an electric oven then tested for their photoactivity. The photoresponse of the n-Fe₂O₃ nanowires was evaluated by measuring the rate of water splitting reaction to hydrogen and oxygen, which is proportional to photocurrent density, J_p. The optimized electric oven-made n-Fe₂O₃ nanowire photoelectrodes showed photocurrent densities of 1.46 mA cm⁻² at measured potential of 0.1 V/SCE at illumination intensity of 100 mW cm⁻² from a Solar simulator with a global AM 1.5 filter. For the optimized carbon modified (CM)-n-TiO₂ synthesized by thermal flame oxidation the photocurrent density for water splitting was found to increase by two fold to 3.0 mA cm⁻² measured at the same measured potential and the illumination intensity. The carbon modified (CM)-n-Fe₂O₃ electrode showed a shift of the open circuit potential by −100 mV/SCE compared to undoped n-Fe₂O₃ nanowires. A maximum photoconversion efficiency of 2.3% at applied potential of 0.5 V/E_aoc was found for CM-n-Fe₂O₃ compared to 1.69% for n-Fe₂O₃ nanowires at higher applied potential of 0.7 V/E_aoc. These CM-n- Fe₂O₃ and n- Fe₂O₃ nanowires thin films were characterized using photocurrent density measurements under monochromatic light illumination, UV-Vis spectra, X-ray diffraction (XRD) and scanning electron microscopy (SEM).     

Solar cells with Cu(In1−xGax)S2 thin films prepared by sulfurization

By rapid thermal processing of Cu/In/GaS precursors, good-quality CuIn_1–xGa_xS₂ films are synthesized. By suppressing the formation of In-rich hillocks, we could obtain homogeneous CuIn_1–xGa_xS₂ surfaces. A conversion efficiency of 12% has been achieved using a relatively low (1.2) Cu/In ratio.     

Preparation of Culn(SxSe1−x)2 thin films by sulfurization and selenization

A CuIn(S_xSe_1−x)₂ alloy thin-film was prepared by selenization of CuInS₂: its composition ratio x can be controlled by the number of selenization cycles implemented. Crystallinity of the films was improved by annealing in vacuum. The resistivity of the film was about 1 Ω cm and increased by one to two orders of magnitude after KCN treatment. An 8.1 % efficiency solar cell was obtained by using this annealed alloy thin-film.     

Structural and photoluminescence study of the quaternary alloys system CuIn(SxSe1−x)2

The full composition range CuIn(S_xSe_1−x)₂ alloy system has been studied using 40 mm length crystal cuts from 10 mm diameter ingots grown by the classical Bridgman method. X-ray diffraction diffractographs show that the CuIn(S_xSe_1−x)₂ compounds have a chalcopyrite structure for each composition x, they exhibit an expansion on the unit cell characteristics by the tetragonal distortion which depends linearly on the electronegativity of the atoms. The photoluminescence spectra is investigated as a function of various compositions, temperature and excitation intensities. Photoluminescence spectra shows a wide variation in the dominant peak location and an overall blue shift with the increase of sulphur content. Photoluminescence CuInS₂ and CuIn(S_0.72Se_0.28)₂ have been studied in detail.     

High performance layered SmBa0.5Sr0.5Co2O5+δ cathode for intermediate-temperature solid oxide fuel cells

The layered SmBa_0.5Sr_0.5Co₂O_5+δ (SBSC) perovskite oxide is synthesized by the Pechini method and investigated as a novel cathode material for intermediate-temperature solid oxide fuel cells (IT-SOFCs). A laboratory-sized Sm_0.2Ce_0.8O_1.9 (SDC)-based tri-layer cell of NiO–SDC/SDC/SBSC is operated from 500 to 700 °C fed with humidified H₂ (3% H₂O) as a fuel and the static ambient air as oxidant. A maximum power density of 1147 mW cm⁻² is achieved at 700 °C. The interfacial polarization resistance is as low as 1.01, 0.38, 0.16, 0.06 and 0.03 Ω cm² at 500, 550, 600, 650 and 700 °C, respectively. The experimental results indicate that SBSC is a very promising cathode material for IT-SOFCs.     

Preparation and characterization of Ce1−x(Gd0.5Pr0.5)xO2 electrolyte for IT-SOFCs

The Ce_1−x(Gd_0.5Pr_0.5)_xO₂ (x = 0–0.24) compositions were synthesized through the sol–gel process followed by low temperature combustion. X-ray diffraction data analysis showed that all the samples exhibit a cubic structure with single phase. The lattice parameter was calculated by rietveld refinement of XRD patterns. Dense ceramics were prepared by sintering the pellets at 1300 °C. The relative density of the samples was over 98%. The surface morphology was studied by Scanning electron microscopy (SEM). Chemical composition was analyzed by Energy dispersive spectroscopy (EDX). A.C. impedance spectroscopy measurements were carried out to study the grain, grain boundary and total ionic conductivity of co-doped ceria samples in the temperature range 150–700 °C. The Ce_0.84(Gd_0.5Pr_0.5)_0.16O₂ composition showed highest grain ionic conductivity i.e., 1.059 × 10⁻² S/cm at 500 °C which is 11.5% higher than the Ce_0.9Gd_0.1O₂ (with an activation energy 0.62 eV). At intermediate temperatures, the Ce_1−x(Gd_0.5Pr_0.5)_xO₂ materials were found to be ionic in nature.     

Preparation and properties of LiCoyMnxNi1−x−yO2 as a cathode for lithium ion batteries

The preparation of LiCo_yMn_xNi_1−x−yO₂ from LiOH·H₂O, Ni(OH)₂ and γ-MnOOH in air was studied in detail. Single-phase LiCo_yMn_xNi_1−x−yO₂ (0y0.3 and x=0.2) is obtained by heating at 830–900°C. The optimum heating temperatures are 850°C for y=0–0.1 and 900°C for y=0.2–0.3. Excess lithium (1z1.11 for y=0.2) and the Co doping level (0.05y0.2) do not significantly affect the discharge capacity of Li_zCo_yMn_0.2Ni_0.8−yO₂. The doping of Co into LiMn_0.2Ni_0.8O₂ accelerates the oxidation of the transition metal ion, and suppresses partial cation mixing. Since the valence of the manganese ion in LiMn_0.2Ni_0.8O₂ is determined to be 4, the formation of a solid solution between LiCo_yNi_1−yO₂ and Li₂MnO₃ is confirmed.     

Development of Ag-(BaO)0.11(Bi2O3)0.89 composite cathodes for intermediate temperature solid oxide fuel cells

The electrochemical performances of Ag-(BaO)_0.11(Bi₂O₃)_0.89 (BSB) composite cathodes on Ce_0.8Sm_0.2O_1.9 electrolytes have been investigated for intermediate temperature solid oxide fuel cells (ITSOFCs) using ac impedance spectroscopy from 500 to 700 °C. Results indicate that the electrochemical properties of these composites are quite sensitive to the composition and the microstructure of the cathode. The optimum BSB addition (50% by volume) to Ag resulted in about 20 times lower area specific resistance (ASR) at 650 °C. The ASR values for the Ag50-BSB and Ag cathodes were 0.32 and 6.5 Ω cm² at 650 °C, respectively. The high performances of Ag-BSB cathodes are determined by the high catalytic activity for oxygen dissociation and ionic conductivity of BSB, and by the excellent catalytic activity for oxygen reduction of silver. The maximum power density of the Ag50-BSB cathode was 224 mWcm⁻² at 650 °C, which classify this composite as a promising material for ITSOFC.