Potential migration of Diisopropyl naphthalenes from recycled paperboard packaging into dry foods

The results of a study of the potential migration of diisopropyl naphthalenes (DIPN) from recycled paperboard packaging into some types of dry solid foodstuffs are reported. Paperboard diskettes containing different DIPN concentrations were prepared and put into contact with four types of dry solid foodstuffs, having high specific surface areas and different lipid contents. At regular intervals the DIPN content in the foods was determined. Two migration mechanisms have been proposed and verified. The first one relates to the direct contact existing between paperboard and foodstuff. The second one refers to the indirect contact between paperboard and food, controlled by an air space created above the paperboard into which the DIPN has diffused. Both mechanisms occurred and the migration depended on different factors: the contact time, the characteristics of the foodstuffs and the DIPN content in the cellulose-based matrix. However, only very low levels of contamination in the foodstuffs occurred in migration. As a consequence, this report also considers possible limitations which could be applied to the content of carbonless copy paper in packaging paperboard formulations.     

Recycled paper–paperboard for food contact materials: Contaminants suspected and migration into foods and food simulant

Contaminant residues in food packaging is a new challenge of our time, as it may pose a threat for consumers. Higher levels of contaminants were observed in food packaging made by recycled materials, even if little information is available for some groups of contaminants. The present study proposes a procedure for analyzing three different groups of organic contaminants in recycled paper and paperboard. Seventeen commercial samples were analyzed for the presence of bisphenol A (BPA), bis (2-ethylhexyl) phthalate (DEHP), nonylphenol monoethoxylate (NMP) and nonylphenol di-ethoxilate (NDP). Not all the samples contained all the contaminants; BPA was the only substance present in all the samples. The concentrations detected were quite high and, in most of the cases, in agreement with results reported in previous studies. Substance migration tests from spiked/non-spiked samples for two dry foods and Tenax® food simulant were undertaken. BPA migration quotients were always lower than 1%, whereas the migration quotients of DEHP were higher than 2.0%. The highest nonylphenols migration quotients were 6.5% for NMP and 8.2% for NDP. Tenax® simulates well the contaminants migration from paperboard to dry food, in some cases being even more severe than the food.     

Investigation of migration from paper and board into food-development of methods for rapid testing

A range of paper and board materials including carton board, corrugated board, napkins and paper towels intended for contact with food have been solvent extracted and substances present at the highest levels identified and quantified by GC/MS. Dibutyl phthalate, and diisopropylnaphthalene (DIPN) were selected to study migration to food and potential food simulants with the aim of developing a simple quick test that will give an equivalent or higher result. Tenax was found to be a suitable food simulant for dry foods and dry 'fatty foods' such as pastry and cake and was also found to be a suitable simulant for pizza base tested at higher temperatures for short contact times. The percentage migration values from corrugated and carton boards were generally in the range 15-40%, with the highest percentage being 49% for rice using conditions representing ambient storage. Quick tests were developed using Tenax under accelerated conditions of 4h at 80°C to cover room temperature storage with dry foods and fatty dry foods. These tests are suitable for compliance testing of paperboard samples if migration limits are applied in future legislation. Migration from tissues, napkins and paper towels was found to be at very low or not detectable levels, even when the levels of DIPN and DBP were significant. It is strongly suspected that this finding is due to a combination of short contact time, low grammage and the fact that the tissues absorb fat and moisture from foods, thus minimizing extraction from the paper. In all cases, the results from migration experiments into food and Tenax indicate that for the substances found at highest concentrations in the paper, currently accepted safety limits were not exceeded where they exist in EU legislation or in working documents applying to plastics.     

纸质食品包装材料的矿物油迁移研究进展

食品中的矿物油污染物是指石油来源的C10~C50烃类化合物, 包括烷烃矿物油(mineral oil saturated hydrocarbons, MOSH)和芳烃矿物油(mineral oil aromatic hydrocarbons, MOAH)2大类。近年来的研究表明, 食品中的矿物油污染物主要来源于食品的回收纸包装材料迁移。本文综述了国外近十年来纸质包装材料的矿物油迁移研究情况, 包括纸质包装材料迁移的矿物油分析方法——液相色谱-气相色谱联用法; 矿物油迁移至食品的2种方式: 气态扩散迁移和包装材料接触迁移; 降低矿物油迁移的技术方法, 即食品包装纸质材料的回收工艺, 向包装纸质中添加活性炭等吸附剂以及增加阻隔层以阻挡矿物油的迁移。旨在为相关企业和机构提供数据与技术参考。     

Kinetic migration studies from packaging films into meat products

One of the main concerns regarding safety of food packaging is the possible migration of chemical substances (monomers and other starting substances, additives, residues) from food contact materials into foods. To evaluate the effect of the fat content and of the temperature of storage on the migration from plastics packaging films into meat products as an important class of foodstuffs, the kinetic mass transport of a model migrant (diphenylbutadiene) from low density polyethylene (LDPE) film in contact with different meat products was investigated. From the data, the diffusion coefficients were calculated for the applied test conditions, by use of a mathematical model. The results showed that migration increased with fat content and storage temperature. Analysis of migration data corresponding to minced pork meat containing different amounts of fat, stored for 10 days at 25°C, revealed an excellent relationship between migration level and fat content. This behaviour was also found for other types of meat products (chicken and pork neck). A simplifying mathematical model was applied to derive effective diffusion coefficients in the polymer which, however, do take kinetic effects in the meat also into account. In the case of pork meat contact, the effective diffusion coefficients derived from mathematical modelling were ten times higher for storage at 25°C (1.88×10(-9)cm(2)s(-1)) than for storage at 5°C (1.2×10(-10)cm(2)s(-1)).     

Time- and temperature-dependent migration studies of Irganox 1076 from plastics into foods and food simulants

The study provides an exhaustive set of migration data for octadecyl 3-(3,5-di-tert-butyl-4-hydroxyphenyl)propionate (Irganox 1076) from low-density polyethylene (LDPE) in several food matrices. Irganox 1076 was used as a model migrant because it represents one of the typical substances used as an antioxidant in food packaging polymers. Kinetic (time-dependent) migration studies of Irganox 1076 were performed for selected foodstuffs chosen with different physical-chemical properties and in relation to the actual European food consumption market. The effect of fat content and of the temperature of storage on the migration from plastic packaging was evaluated. The results show that migration increased with fat content and storage temperature. All data obtained from real foods were also compared with data obtained from simulants tested in the same conditions. In all studied cases, the kinetics in simulants were higher than those in foodstuffs. The work provides data valuable for the extension of the validation of migration model developed on simulants to foodstuffs themselves.     

塑料食品包装材料中有毒有害化学残留物及分析方法

食品包装材料中有毒有害化学物质的迁移是引起食品污染的重要途径之一。本文主要根据近年来发表的有关食品包装材料、卫生检测领域的相关文献为基础,针对塑料食品包装材料中的单体、低聚体、添加剂和污染物等几类有毒有害化学物质的组成、毒性、卫生限量标准及主要检测方法进行了分析,为相关食品包装企业的质量控制技术人员和科研工作者提供参考。     

The specific diffusion behaviour in paper and migration modelling from recycled board into dry foodstuffs

Recycled board plays an important role in food packaging, but the great variety of organic impurities must be considered as potential food contaminants. The diffusion behaviour of the impurities is significantly different from that in plastic materials. The two-layer concept for paper and board introduced recently is now treated in more detail. In the rate-determining surface region the diffusion coefficients of the n-alkanes in the homologous series with 15–35 carbon atoms decrease proportionally as their vapour pressures. This leads to a different equation of the diffusion coefficients in comparison with that for the core layer. Different polarities of the migrants have additional influences on the diffusion due to their interactions with the fibre matrix. A new analytical method for the quantification of aromatic impurities has previously been developed. Based on this method and on the described diffusion behaviour, a migration model for specific and global mass transfer of impurities from recycled board into dry food and food simulants is given.     

The determination of monomers and oligomers from polyester-based can coatings into foodstuffs over extended storage periods

The polymeric coating used in metal packaging such as cans for foods and beverages may contain residual amounts of monomers used in the production of the coating, as well as unreacted linear and cyclic oligomers. Traditionally, although designed for use with plastic food contact materials, food simulants have been used to determine the migration of monomers from coatings into foodstuffs. More recently, food simulants have also been used to determine oligomeric species migrating from can coatings. In the work reported here, the migration of both monomers and oligomers from polyester-based can coatings into food simulants and foodstuffs, some of which were towards the end of their shelf-life, is compared. The concentrations of monomers and selected oligomers in canned foods at the end of their shelf life were found to be significantly lower than those in food simulants, which in turn was lower than those in the extraction solvent acetonitrile.     

Contamination of packaged food by substances migrating from a direct-contact plastic layer: Assessment using a generic quantitative household scale methodology

The contamination risk in 12 packaged foods by substances released from the plastic contact layer has been evaluated using a novel modeling technique, which predicts the migration that accounts for (i) possible variations in the time of contact between foodstuffs and packaging and (ii) uncertainty in physico-chemical parameters used to predict migration. Contamination data, which are subject to variability and uncertainty, are derived through a stochastic resolution of transport equations, which control the migration into food. Distributions of contact times between packaging materials and foodstuffs were reconstructed from the volumes and frequencies of purchases of a given panel of 6422 households, making assumptions about household storage behaviour. The risk of contamination of the packaged foods was estimated for styrene (a monomer found in polystyrene yogurt pots) and 2,6-di-tert-butyl-4-hydroxytoluene (a representative of the widely used phenolic antioxidants). The results are analysed and discussed regarding sensitivity of the model to the set parameters and chosen assumptions.     

Use of Tenax® films to demonstrate the migration of chemical contaminants from cardboard into dry food

ABSTRACT

Contaminants in food packaging are a challenge of our time since the packaging material itself has been found to represent a source of food contamination through the migration of substances from it. Before first use, packaging materials destined for the packaging of dry foods can be evaluated by performing migration experiments with the simulant for dry foods, Tenax®. This simulant is commercially available as a powder that is more difficult to handle during the migration experiments. This paper reports the development of a Tenax film. The film can be applied to the cardboard surface to conduct the migration test. After the migration is completed, the film can be easily extracted to determine the concentration of the contaminants in the film. Finally, the performance of the Tenax film was compared with the conventional Tenax powder for the evaluation of 15 model migrants.     

Time‐ and temperature‐dependent migration studies of Irganox 1076 from plastics into foods and food simulants

The study provides an exhaustive set of migration data for octadecyl 3‐(3,5‐di‐tert‐butyl‐4‐hydroxyphenyl)propionate (Irganox 1076) from low‐density polyethylene (LDPE) in several food matrices. Irganox 1076 was used as a model migrant because it represents one of the typical substances used as an antioxidant in food packaging polymers. Kinetic (time‐dependent) migration studies of Irganox 1076 were performed for selected foodstuffs chosen with different physical–chemical properties and in relation to the actual European food consumption market. The effect of fat content and of the temperature of storage on the migration from plastic packaging was evaluated. The results show that migration increased with fat content and storage temperature. All data obtained from real foods were also compared with data obtained from simulants tested in the same conditions. In all studied cases, the kinetics in simulants were higher than those in foodstuffs. The work provides data valuable for the extension of the validation of migration model developed on simulants to foodstuffs themselves.     

Model studies of migration from paper and board into fruit and vegetables and into Tenax™ as a food simulant

Four samples of paper and board (P/B) of a type used for packaging dry foods were subjected to migration tests using mushrooms, apples, potatoes and bananas, and using the polymeric powder Tenax? as a food simulant. The P/B samples contained only low levels of diisopropylnaphthalene (DiPN) and diisobutyl phthalate (DiBP) and so the experiments were conducted after impregnating the P/B with added model substances. These were o-xylene, acetophenone, dodecane, benzophenone, DiPN and DiBP. Migration levels depended strongly on the nature of the substance and on the nature of the food and much less on the characteristics of the P/B, except insofar as they affected the contact area – flexible papers giving more extensive contact with the food than thick rigid board. Migration into Tenax? was at least a factor of 10 higher than migration into the fresh fruit and vegetables. The food samples were placed in contact with the P/B and then overwrapped loosely with aluminium foil and so this correction factor will tend to be conservative compared with a more open storage of the packed foods. Washing, peeling or cooking the fruits and vegetables after contact with the P/B had a surprisingly small effect on contaminant levels in general, and no one processing step was effective in giving a significant reduction of all the types of chemicals studied. This was because either they had penetrated into the food (so resisting peeling), or were not freely water-soluble (so resisting washing) or were not particularly volatile (so resisting loss by evaporation during cooking).     

Correlation of foodstuffs with ethanol–water mixtures with regard to the solubility of migrants from food contact materials

Today most foods are available in a packed form. During storage, the migration of chemical substances from food packaging materials into food may occur and may therefore be a potential source of consumer exposure. To protect the consumer, standard migration tests are laid down in Regulation (EU) No. 10/2011. When using those migration tests and applying additional conservative conventions, estimated exposure is linked with large uncertainties including a certain margin of safety. Thus the research project FACET was initiated within the 7th Framework Programme of the European Commission with the aim of developing a probabilistic migration modelling framework which allows one (1) to calculate migration into foods under real conditions of use; and (2) to deliver realistic concentration estimates for consumer exposure modelling for complex packaging materials (including multi-material multilayer structures). The aim was to carry out within the framework of the FACET project a comprehensive systematic study on the solubility behaviour of foodstuffs for potentially migrating organic chemicals. Therefore a rapid and convenient method was established to obtain partition coefficients between polymer and food, K_P/F. With this method approximately 700 time-dependent kinetic experiments from spiked polyethylene films were performed using model migrants, foods and ethanol–water mixtures. The partition coefficients of migrants between polymer and food (K_P/F) were compared with those obtained using ethanol–water mixtures (K_P/F’s) to investigate whether an allocation of food groups with common migration behaviour to certain ethanol–water mixtures could be made. These studies have confirmed that the solubility of a migrant is mainly dependent on the fat content in the food and on the ethanol concentration of ethanol–water mixtures. Therefore dissolution properties of generic food groups for migrants can be assigned to those of ethanol–water mixtures. All foodstuffs (including dry foods) when allocated to FACET model food group codes can be classified into a reduced number of food categories each represented by a corresponding ethanol–water equivalency.     

Retention of α-tocopherol in low-density polyethylene (LDPE) and polypropylene (PP) in contact with foodstuffs and food-simulating liquids

Alpha-tocopherol occurs as a natural antioxidant in many foods and has also found use as a stabiliser in polymeric packaging materials. During storage of a food in contact with a plastic material, α-tocopherol may be released from the packaging material and transferred into the food. An active packaging application with the transfer of a substance, such as an antioxidant, from a packaging material to a food may help to prolong the shelf-life of the food. In this study, the retention of α-tocopherol in low-density polyethylene (LDPE) and polypropylene (PP) was investigated for contact with liquid foods with different fat contents and food simulants with different ethanol contents. The PP film exhibited excellent retention of α-tocopherol when in contact with all media, whereas some losses were observed from the LDPE film. A number of factors including fat, alcohol and organic acid contents of the various foodstuffs seemed to influence the loss of α-tocopherol from the LDPE film. © 1999 Society of Chemical Industry     

Contamination of dry foods with trimethyldiphenylmethanes by migration from recycled paper and board packaging

Contamination of foods with trimethyldiphenylmethanes is reported and the origin is shown to be migration from food packaging materials of which the use of recycled carbonless copy paper was found to be the major source. This chemical is one of the solvents used in the carbonless copy paper and its presence in food and the environment has not been previously identified. In this paper we have pursued previous studies on diisopropylnaphthalenes and hydrogenated terphenyls contamination from packaging and now report the identification of this new food contaminant and present evidence of its source. Solid foods such as egg pasta, barley coffee and rice were analysed by GC/MS and a mean concentration of 18 µg/kg of trimethyldiphenylmethanes was found. Extracts from carbonless copy paper were analysed by proton NMR to characterize the trimethyldiphenylmethanes. Since trimethyldiphenylmethanes are found in solid food together with diisopropylnaphthalenes, and considering their similar chemical character, they may follow the same migration pathway as one another.     

Estimation of exposure to food packaging materials. 1: Development of a food-packaging database

A food-packaging database was developed to provide qualitative information on the types of packaging materials used for foods. Packaging information was collected from a sample of 594 children aged 5-12 years as part of a national children's food survey carried out in Ireland during 2003-04. All the food packaging collected during the survey was forwarded to the coordinating centre for further analysis and entry into the Irish Food Packaging Database. The database was created in Microsoft Access® and stored information on: the brand of the food, the packaging type, the unit weight, the contact layer, the European Union food type (i.e. aqueous, acidic, alcoholic or fatty) and other relevant parameters. Of the 5551 different brand foods consumed by children in the food survey, packaging information was collected on 3441 (62%). As some brand foods had different unit weights and packaging formats, there was duplication of some brand foods in the database to account for this fact. Therefore, there were 3672 packaging entries in the database. Of these, plastics were the most common packaging contact layer (n = 2874, 78.3%). Multimaterial multilayers with a plastic contact layer accounted for 459 (12.5%) entries. Polyethylene was the most frequently used contact layer (n = 941), with polypropylene a close second (n = 809). This database is unique in Europe for the quality and amount of food packaging information it contains and could be used to develop packaging use factors for a more refined exposure assessment to food packaging materials in the European Union.     

陶瓷、玻璃食品包装中化学物质的检测和迁移研究进展

陶瓷和玻璃食品包装中的化学物质迁移到食品中危害消费者的健康,为此国内外建立了相关的法规来确保陶瓷和玻璃包装使用的安全性。本文对陶瓷和玻璃食品包装中的有害金属元素、欧盟和我国相关法规中的限量标准、与陶瓷接触的食品样品的消解方法、陶瓷和玻璃食品包装中有害金属元素的检测方法和迁移研究予以综述。     

纳米塑料复合食品包装中的纳米成分及其迁移研究进展

在塑料食品包装中加入纳米材料可以实现很好的机械性、气体阻隔性或抗菌性等优良性能。然而在与食品 接触的过程中这些纳米材料也有可能迁移到食品中,从而对消费者的健康产生威胁,甚至对市场及消费者信心造成 负面影响。对纳米材料进行迁移研究是对其进行风险评估的重要一环,已经得到国内外学者的广泛关注。本文综述 了纳米塑料复合包装的种类、在食品包装中应用较多的纳米材料及其作用,并详细分析了食品包装中纳米材料向食 品或食品模拟物迁移的研究。结果表明：食品包装中纳米材料向食品或食品模拟释放的量较小,但到目前为止,关 于它们是否会以纳米形态释放出来仍然没有达成统一意见。另外,微波处理、塑料助剂的添加可以影响纳米材料的 释放。     

Studies on the usability of recycled PET for food packaging applications

The need of and opportunities for recycling of plastics for food packaging have been recognized, and a lot of work to find meaningful and cost-effective solutions to this issue is in progress. The safety of recycled plastics for food contact use is largely dictated by the ability of post-consumer contaminants to absorb into recycled materials and later diffuse from recycled plastics into the food. The objective of the present study was to establish a suitable analytical approach to identifying and quantifying any chemical substances that derive from the earlier use and remain in the polyethylene terephthalate (PET). A simple gas chromatographic technique using flame ionization detection was developed to allow quantification of solvent extractable compounds in a series of recycled PET samples. Identification of the nature and extent of contaminants in the PET samples was also attempted using GC/MS analysis.