Coir pith/nylon/epoxy hybrid composites: Dynamic mechanical,ageing, and dielectric properties

Coir pith/epoxy, nylon/epoxy, and coir pith/nylon/epoxy composites were prepared keeping the coir pith content at 65%. Two series of the above composites, one with chemically treated coir pith and another without chemically treated coir pith were fabricated. The Dynamic mechanical properties of composites were evaluated with respect to type of composites and treatment. Storage modulus was found to improve with hybridization and chemical treatment. Meanwhile Tan δ of composites were found to be decreased with hybridization and chemical treatment. Compressive strength of composites with chemically treated coir pith was found to be higher than other composite samples and this has been justified in terms of increased crystallinity of coir pith on treatment. The studies on sea water ageing of composites also indicated improved stability of composites with hybridization and chemical treatment. The dielectric properties of the boards were also evaluated in this investigation and the boards were found to show lower dielectric constant with chemical treatment of coir pith. POLYM. COMPOS., 38:1671–1679, 2017. © 2015 Society of Plastics Engineers     

Physical,mechanical, and water absorption behavior of coir/glass fiber reinforced epoxy based hybrid composites

Fiber reinforced polymer composites has been used in a variety of application because of their many advantages such as relatively low cost of production, easy to fabricate, and superior strength compare to neat polymer resins. Reinforcement in polymer is either synthetic or natural. Synthetic fiber such as glass, carbon, etc. has high specific strength but their fields of application are limited due to higher cost of production. Recently there is an increase interest in natural composites which are made by reinforcement of natural fiber. In this connection, an investigation has been carried out to make better utilization of coconut coir fiber for making value added products. The objective of the present research work is to study the physical, mechanical, and water absorption behavior of coir/glass fiber reinforced epoxy based hybrid composites. The effect of fiber loading and length on mechanical properties like tensile strength, flexural strength, and hardness of composites is studied. The experimental results reveal that the maximum strength properties is observed for the composite with 10 wt% fiber loading at 15 mm length. The maximum flexural strength of 63 MPa is observed for composites with 10 wt% fiber loading at 15 mm fiber length. Similarly, the maximum hardness value of 21.3 Hv is obtained for composites with 10 wt% fiber loading at 20 mm fiber length. Also, the surface morphology of fractured surfaces after tensile testing is examined using scanning electron microscope (SEM). POLYM. COMPOS., 35:925–930, 2014. © 2013 Society of Plastics Engineers     

Dynamic mechanical analysis of pineapple leaf/glass hybrid fiber reinforced polyester composites

The dynamic mechanical properties of randomly oriented intimately mixed hybrid composites based on pineapple leaf fibers (PALF) and glass fibers (GF) in unsaturated polyester (PER) matrix were investigated. The PALFs have high‐specific strength and improve the mechanical properties of the PER matrix. In this study, the volume ratio of the two fibers was varied by incorporating small amounts of GF such as PALF/GF, 90/10, 80/20, 70/30, and 50/50, keeping the total fiber loading constant at 40 wt%. The dynamic modulus of the compositeswas found to increase on GF addition. The intimately mixed (IM) hybrid composites with PALF/GF, 80/20 (0.2 V_f GF) showed highest E′ values and least damping. Interestingly, the impact strength of the composites was minimum at this volume ratio. The composites with 0.46 V_f GF or PALF/GF (50/50) showed maximum damping behavior and highest impact strength. The results were compared with hybrid composites of different layering patterns such as GPG (GF skin and PALF core) and PGP (PALF skin and GF core). IM and GPG hybrid composites are found more effective than PGP. The activation energy values for the relaxation processes in different composites were calculated. The overall results showed that hybridization with GF enhanced the performance properties. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Effects of glass fibers and polypropylene/glass fiber hybrid fibers on the kinetics and mechanical properties of epoxy composites

Curing reactions of diglycidyl ether of bisphenol F (DGEBP‐F) and pre‐catalyzed methyltetrahydrophthalic anhydride (MTHPA) with benzyl triethyl ammonium chloride (BTEAC) were studied and effects of glass fibers evaluated. The influence on the kinetics of glass fibers and a hybrid blend of maleated polypropylene + glass fibers is studied. Isothermal and dynamic kinetic parameters are determined by differential scanning calorimetry (DSC). Applicability of the autocatalytic model is investigated. The model serves well in the range of degrees of conversion between 25 and 80%. At high conversion rates the diffusion control becomes apparent. Glass fibers accelerate the curing, shortening the time needed to reach the maximum reaction rate; this is reflected in lower activation energies for curing in comparison to the neat resin. The effects observed can be explained by a reaction between the amine group present on the fiber surfaces and the epoxy glycidyl groups. The result of both isothermal and non‐isothermal curing of resin + glass fibers commingled with polypropylene are close to those for the neat resin. The reinforcement increases the elastic modulus 12 times, the tensile strength 2 times, and the impact strength 285 times. The glass fibers + commingled polypropylene reinforcement provides comparable mechanical properties as glass fibers alone when normalized with respected to the density fraction of the fibers.     

Dynamic mechanical,mechanical and morphological properties of reactive thermotropic liquid crystalline polymer/unsaturated polyester/glass fibre hybrid composites

Abstract

Unsaturated polyester (UP) reinforced with self-synthesised reactive thermotropic liquid crystalline polymer (TLCP)–methacryloyl copolymer (LCMC) and glass fibre (GF), the hybrid composites of UP/GF/LCMC were prepared by moulding technology. The dynamic mechanical analysis indicated that storage modulus and glass transition temperature (T _g) of hybrid composites increased significantly because of the addition of LCMC. The effect of LCMC content on the mechanical properties of LCMC/UP/GF hybrid composites such as impact strength, specific strength and modulus and load–displacement relationship were also investigated through static mechanical tests. The mechanical properties of hybrid composites increased significantly because of the addition of LCMC. The crystal behaviour analysis of LCMC/UP blend was investigated by X-ray diffraction and polarising optical microscopy. The results showed that the crystal phase and texture structure of LCMC still existed in the blends after blending with UP. The morphology of fracture surfaces of hybrid composites containing different TLCP contents was observed by scanning electron microscopy. The present paper discussed the mechanism for the improvement of dynamic mechanical and mechanical properties.     

Fabrication and mechanical properties of glass fiber‐reinforced wood plastic hybrid composites

To fully utilize the resource in the municipal solid waste (MSW) and improve the strength and toughness of wood plastic composites, glass fiber (GF)‐reinforced wood plastic hybrid composites (GWPCs) were prepared through compounding of recycled high‐density polyethylene (HDPE) from MSW, waste wood fibers, and chopped GF. Mechanical tests of GWPCs specimens with varying amounts of GF content were carried out and the impact fractured surface of GWPCs was observed through scanning electron microscope (SEM). The tensile strength of GWPCs and the efficiency coefficient values were predicted by Kelly‐Tyson method. The results indicated that the tensile strength and impact strength of GWPCs could be improved simultaneously by adding type L chopped GF (L‐GF), and would be dropped down when type S chopped GF (S‐GF) was included. The tensile strength of GWPCs was well accordant with the experimental result. The efficiency coefficient values of S‐GF and L‐GF are ?0.19 and 0.63, respectively. Inspection of SEM micrographs indicated that L‐GF had achieved full adhesion with the plastic matrix through addition of maleic anhydride‐g‐polyethylene. The main fracture modes of GWPCs included pullout of GF, broken of matrix, and interfacial debonding. Because of the synergistic effects between hybrid components in GF/wood fiber/HDPE hybrid system, a special 3D network microstructure was formed, which was the main contribution to the significant improvement in the tensile strength and impact strength of L‐GF‐reinforced hybrid composites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Dynamic mechanical analysis of the effect of water on glass bead–epoxy composites

Dynamic mechanical analysis (DMA) has been used to investigate the effect of water and glass bead surface treatment on the properties of glass bead–epoxy composites. By treating or not treating the glass beads with a silane coupling agent, we fabricated composites with ostensibly good or poor interfacial adhesion. SEM images of fracture surfaces and water uptake data confirmed this picture. We used dynamic mechanical tests to measure the material properties of dry and wet specimens. Temperature sweep tests of atmosphere-conditioned specimens indicated that the value of the loss tangent at the temperature of the α-α-relaxation peak was most sensitive to interfacial adhesion. For wet specimens, the magnitude of an additional relaxation process, denoted as the ω-relaxation, correlated strongly with water uptake and, indirectly, interfacial adhesion. Master curves constructed from frequency sweep tests also manifested differences among dry and wet specimens, but shift factor data suggested that these tests were more prone to complications due to water loss. Apparent activation energies of α- and β-relaxation processes were statistically significant indicators of interfacial adhesion in dry and wet composites, respectively. © 1996 John Wiley & Sons, Inc.     

Dynamic mechanical properties of some epoxy matrix composites

Dynamic mechanical properties of some epoxy matrix composites have been studied, comparing experimental data with theoretical models. The matrix in all composite samples was Shell Epon 828, a diglycidyl ether of bisphenol A, cured with meta-phenylenediamine. Fibrous composite samples were made with glass and graphite fibers. Particulate composite samples were made with glass microspheres, atomized aluminum, powdered silica, alumina, asbestos, mica, carbon black, and graphite. The dynamic elastic modulus and damping of these samples were measured at temperatures between 85° and 345°K by a free-free flexural resonance technique. The dynamic modulus of parallel fiber composites follows the linear rule of mixtures for low fiber volume fractions; deviations from linearity at higher volume fractions appear to be due to defects caused by the sample fabrication technique. Dynamic moduli of the particulate composites conform, within experimental error, to the static modulus theory of Wu up to filler volume fractions of 0.35 to 0.40. Deviations from Wu's theory at higher volume fractions may be due to agglomeration of filler particles. The damping of particulate composites with quasi-spherical filler particles appears to follow the rule of mixtures. In particulate composites with needle- and flake-type fillers, and in fibrous composites, the fillers are more highly stressed; with more of the strain energy in the low-damping fillers, overall damping is reduced. Damping greater than that attributable to the matrix and filler may be due to slippage at the interface between them. In addition to supporting Wu's theory of the elastic modulus of a particulate composite, this study demonstrates the utility of the nondestructive free-free flexural resonance techniques for obtaining a large body of reliable data in a short time from relatively few small samples. This greatly facilitates the experimental testing of theoretical models and the evaluation of fillers, matrix materials, and fabrication techniques.     

Effect of coupling agents on the mechanical properties of mica/epoxy and glass fiber/mica/epoxy composites

The effect of coupling agents, two silane and one zirconate, on the mechanical properties of mica/epoxy and glass fiber/mica/epoxy composites has been investigated. The results showed that tensile modulus and flexural strength and modulus values were improved by the surface treatment of the coupling agents. The property retention was also found to be better in the case of coupling agent-treated mica/epoxy samples after boiling in water for 2h. In the case of glass fiber/mica/epoxy composites, the flexural modulus and interlaminar shear strength values improved with increase in mica content, but the effect of coupling agents was not pronounced.     

改性空心玻璃微珠/环氧树脂复合材料力学性能研究

采用偶联剂对玻璃微珠表面进行改性处理,借助超声波振动,使改性空心玻璃微珠在环氧树脂中均匀、稳定分散,增强了玻璃微珠与环氧树脂之间的相容并探讨了改性空心玻璃微珠对环氧树脂力学性能的影响。结果表明,复合材料中改性空心玻璃微珠添加质量分数为3%时,其拉伸强度达到最大值68.54 MPa,与空白样相比提高了20.3%;冲击强度达到最大值24.42 kJ/m2,比纯环氧树脂提高了166%;KIC(断裂韧性)达到最大值2.338 MPa/m2,是空白试样的2.27倍,增韧效果较为明显。     

Dynamic mechanical properties of oil palm fiber/phenol formaldehyde and oil palm fiber/glass hybrid phenol formaldehyde composites

The dynamic mechanical properties of oil palm fiber reinforced phenol formaldehyde (PF) composites and oil palm/glass hybrid fiber reinforced PF composites were investigated as a function of fiber content and hybrid fiber ratio. The dynamic modulus of the neat PF sample decreases with decrease in frequency. Glass transition attributed with the α relaxation of the neat PF sample was observed around 140°C. Tanδ values and storage modulus show great enhancement upon fiber addition. The value increases with increase in fiber content. The loss modulus shows a reverse trend with increase in fiber loading. Incorporation of oil palm fiber shifts the glass transition towards lower temperature value. The glass transition temperature of the hybrid composites is lower than that of the unhybridized composites. The highest value of mechanical damping is observed in hybrid composites. Storage modulus of the hybrid composites is lower than unhybridized oil palm fiber/PF composite. A similar trend is observed for loss modulus. Activation energies for the relaxation processes in different composites were calculated. Activation energy is increased upon fibrous reinforcement. Complex modulus variations and phase behavior of the composites were studied from Cole‐Cole plots. Finally, master curves for the viscoelastic properties of the composites were constructed on the basis of time‐temperature superposition principle. POLYM. COMPOS., 26:388–400, 2005. © 2005 Society of Plastics Engineers     

Morphological,mechanical, and electromagnetic interference shielding effectiveness characteristics of glass fiber/epoxy resin/MWCNT buckypaper composites

Glass fiber/epoxy resin composites (GF/EP) using one and three multi-walled carbon nanotube buckypapers (BP) were obtained and their complex parameters, reflectivity, and electromagnetic interference (EMI) shielding effectiveness (SE) at X-band (8.2–12.4 GHz) and Ku-band (12.4–18 GHz) were evaluated. The preparation of BP used polyacrylonitrile (PAN) nanofibers (PF These composites show both large storage and energy loss capacity in both bands revealing promising results related to EMI SE applications. Besides, a high attenuation of around 67% and 72% were achieved for BP based composites. The cross-section view of the buckypaper and the laminates was analyzed by scanning electron microscopy (SEM). The incorporation of the CNT film into the laminates showed no improvements in the elastic properties through dynamic mechanical analyses (DMA). Nevertheless, a decrease in the shear properties by the compression shear test (CST) and interlaminar shear strength (ILSS) has been observed. GF/EP/BP/PF composite presented a reduction of 29 and 39% in its ILSS properties compared to the base laminate (GF/EP). Also, the decrease was even more significant, revealing a steep reduction in its CST properties. On the other hand, the removal of the pan nanofiber (PF) led to better mechanical properties for GF/EP/BP/RPF composites. Results have shown ILSS values of 47.4 ± 2.2 MPa which are close to the base laminate (52.4 ± 3.1 MPa). The removal of the PF provided larger porous in the CNT network, making the impregnation by epoxy easier in the BP/RPF which resulted in improved shear properties compared to GF/EP/BP/PF samples.     

Wear response of glass fiber and ceramic tile-reinforced hybrid epoxy matrix composites

Iranian Polymer Journal - This study presents the tribological behavior of epoxy matrix composites containing two different fillers. The composites contain fillers with different particle sizes...     

Physical and mechanical behavior of unidirectional banana/jute fiber reinforced epoxy based hybrid composites

During the last few years, natural fiber composites are replacing synthetic fiber composites for practical applications due to their advantages like low density, light weight, low cost, biodegradability and high specific mechanical properties. In this connection, the present investigation deals with the fabrication and mechanical properties of unidirectional banana/jute hybrid fiber reinforced composites and compares with the single natural fiber reinforced composites. The physical and mechanical properties of the natural fiber composites were obtained by testing the composite for density, tensile, flexural, inter‐laminar shear, impact, and hardness properties. The composite specimens with different weight percentages of fibers were fabricated by using hand lay‐up technique and testing were carried out as per ASTM standards. Incorporation of both the fibers into epoxy matrix resulted in an increase in mechanical properties up to 30 wt% of fiber loading. It is found that the hybrid composite give encouraging results when compared with the individual fiber composites. The morphologies of the composites are also studied by scanning electron microscope. POLYM. COMPOS., 38:1396–1403, 2017. © 2015 Society of Plastics Engineers     

Thermal and mechanical properties of hybrid carbon/oxidized polyacrylonitrile fibers‐epoxy composites

Nowadays, hybrid composites are one of the important materials in industry due to their special properties. In this research, hybrid oxidized polyacrylonitrile (PAN) and carbon fibers reinforcement were used in epoxy matrix. The hybrid composites were fabricated using the hand lay‐up technique by placing the reinforcements in different layering sequences. Thermal and mechanical properties of these hybrid composites were investigated by thermal analysis, horizontal burning, tensile and bending tests. The tensile test results indicated that increasing oxidized polyacrylonitrile fibers (OPFs) to carbon fibers ratio decreased tensile strength and elastic modulus but increased failure strain. Hybrid oxidized PAN and carbon fibers reinforcement in composites led to decreasing flexural stress and modulus, and increasing flame retardancy. Thermal analysis results also showed that the maximum rate of mass loss in all composites was 370.6°C. It was also found that the maximum and minimum amounts of char residue at 900°C were related to the composites with four layers of carbon and OPFs, respectively. POLYM. COMPOS., 38:1412–1417, 2017. © 2015 Society of Plastics Engineers     

Water absorption and mechanical properties of PP/HIPS hybrid composites filled with wood flour

Water absorption and mechanical performance of the injection‐molded hybrid composites prepared from different ratios of two polymer blends (57 wt%), two compatibilizers (3 wt%), and two wood species (40 wt%) were investigated. The ratio of polypropylene and high‐impact polystyrene (HIPS) gradually increased in the blend (from 10 to 30 wt%). Styrene–ethylene–butylene–styreneblock copolymer and maleic anhydride‐grafted PP (MAPP) were used as compatibilizer (3 wt%). The shore D hardness of the PP/wood composites was improved by the incorporation of the HIPS. The HIPS/wood flour composites showed higher tensile modulus but lower tensile strength than the PP/wood composites. The water resistance of the PP/wood composites decreased with increasing HIPS content. POLYM. COMPOS., 38:863–869, 2017. © 2015 Society of Plastics Engineers     

Mechanical properties of poly(vinyl chloride)/wood flour/glass fiber hybrid composites

Short glass fibers were added to poly(vinyl chloride) (PVC)/wood flour composites as reinforcement agents. Unnotched and notched impact strength of PVC/wood flour/glass fiber hybrid composites could be increased significantly without losing flexural properties by adding type L glass fibers and over 40% of PVC. There was no such improvement when using type S glass fiber. The impact strength of hybrid composites increased along with the increment of the type L glass fiber content at a 50% PVC content. At high PVC contents, impact fracture surfaces were characterized by wood particle, glass fiber breakage and pullout, whereas interfacial debonding was the dominant fracture mode at higher filler concentrations. The significant improvement in impact strength of hybrid composites was attributed to the formation of the three‐dimensional network glass fiber architecture between type L glass fibers and wood flour.     

Degradation and enhancement of the fatigue behavior of glass/graphite/epoxy hybrid composites after accelerated aging

The tensile fatigue characteristics of graphite/glass/epoxy hybrid composites were investigated before and after exposure to various high humidity environments. Accelerated aging treatments of 98 percent RH and 120°F were applied both continuously for 500 and 1000 h and coupled with a 350°F thermal shock after ?67°F low temperature exposure. This latter thermohumidity cycle was applied for 500 h total exposure time. Cyclic loading tests showed that degradation due to the moisture and thermohumidity conditioning treatments was in-most cases small. Some bereficial behavior of the humidity exposure was also noted. The hybrid fatigue characteristics both before and after exposure were a blend of the nearly flat advanced fiber composite S-N behavior and the highly curved glass fiber composite S-N behavior. This was attributed to a mixture of failure modes for the hybrid system.     

Investigation of mechanical properties of alumina nanoparticle‐loaded hybrid glass/carbon‐fiber‐reinforced epoxy composites

This research work investigates the tensile strength and elastic modulus of the alumina nanoparticles, glass fiber, and carbon fiber reinforced epoxy composites. The first type composites were made by adding 1–5 wt % (in the interval of 1%) of alumina to the epoxy matrix, whereas the second and third categories of composites were made by adding 1–5 wt % short glass, carbon fibers to the matrix. A fourth type of composite has also been synthesized by incorporating both alumina particles (2 wt %) and fibers to the epoxy. Results showed that the longitudinal modulus has significantly improved because of the filler additions. Both tensile strength and modulus are further better for hybrid composites consisting both alumina particles and glass fibers or carbon fibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39749.     

Dynamic mechanical properties of extruded nylon–wood composites

Dynamic mechanical properties determine the potential end use of a newly developed extruded nylon–wood composite in under‐the‐hood automobile applications. In this article, the dynamic mechanical properties of extruded nylon–wood composites were characterized using a dynamic mechanical thermal analyzer (DMTA) to determine storage modulus, glass transition temperature (T_g), physical aging effects, long‐term performance prediction, and comparisons to similar products. The storage modulus of the nylon–wood composite was found to be more temperature stable than pure nylon 66. The T_g range of the nylon–wood composite was found to be between 23 and 56°C, based on the decrease in storage modulus. A master curve was constructed based on the creep curves at various temperatures from 30 to 80°C. The results show that the relationship between shift factors and temperature follows Arrhenius behavior. Nylon–wood composites have good temperature‐dependent properties. Wood fillers reduced the physical aging effects on nylon in the wood composites. The comparison of the nylon–wood composite with other similar products shows that nylon–wood composites are a promising low cost material for industrial applications. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers