Rapid thermal alloyed ohmic contact on inp

The results of a study of the electrical and metallurgical properties of thin metallic layers deposited on InP for use as an ohmic contact are presented. A rapid thermal annealing system was used to alloy AuGe/Ni/Au contacts ton-type ion implanted InP. Rutherford backscattering and contact resistivity measurement were used to evaluate the structural and electrical characteristics of these rapid thermal alloyed thin films. Varying degrees of mixing between the metals and the semiconductor were found depending on the temperature and temperature-time cycle. These results were compared to furnace and graphite strip-heater alloying techniques. A correlation between the interface structure and the contact resistance was found. Temperatures between 430 and 450° C and alloying time of 2 sec have produced the best electrical results, with specific contact resistance as low as 2*10^?7 Ω cm² on semi-insulating InP which was Siimplanted with a peak concentration about 2*10¹⁸ cm^?3. The optimum alloy temperature is marked by the onset of substantial wrinkling of the contact surface, whereas essentially smooth surfaces are obtained at temperatures below optimum. The depth of the alloyed ohmic contact is controlled by the time of heating and could be less than 1000Å.     

金属Al与半导体Ge欧姆接触的制备和表征

基于圆形传输线模型,通过测试样品的比接 触电阻率和电流-电压(I-V)特性曲线,分析 对比了Al与Si基上外延生长的p型Ge、n型Ge和n型Si的接触特性。实验结果发现,由于金 属与Ge材料接触存在强烈的费米钉效应,导致金属与n型Ge接触有高的接触电阻,难实 现低的比接触电阻率;而Al与p型Ge在掺杂浓度为4.2×10¹⁸ cm－3时,并且经过退火,比接 触电阻率能达到4.0×10－7 Ω·cm²;Al与n型Ge和n型Si接 触电极相比,后者可形成良好的 欧姆接触,其比接触电阻率较n型Ge接触降低了1个量级,经合金化处理后的Al/n⁺Si接触 电阻率能达到5.21×10－5 Ω·cm²,达到了制作高性能Ge 光电器件的要求。     

Ti/WSi/Ni ohmic contact to n-type SiCN

Ti/WSi/Ni contact to n-type SiCN was investigated using the circular transmission line method. Current–voltage characteristics, X-ray diffraction and X-ray photoelectron spectroscopy were used to characterize the contacts before and after annealing. It is shown that the conducting behavior of the contacts is dependent on the annealing temperature. After annealing at 900 ℃ or above, ohmic contacts with specific contact resistivity were achieved. The 1000-℃-annealed contact exhibits the lowest specific contact of 3.07E-5 Ω? cm2. The formation of ohmic contact with low specific contact resistivity was discussed.     

Ti/WSi/Ni ohmic contact to n-type SiCN

Ti/WSi/Ni contact to n-type SiCN was investigated using the circular transmission line method. Current-voltage characteristics, X-ray diffraction and X-ray photoelectron spectroscopy were used to characterize the contacts before and after annealing. It is shown that the conducting behavior of the contacts is dependent on the annealing temperature. After annealing at 900 ℃ or above, ohmic contacts with specific contact resistivity were achieved. The 1000-℃-annealed contact exhibits the lowest specific contact of 3.07 ×10-5 Ω·cm2. The formation of ohmic contact with low specific contact resistivity was discussed.     

Effect of Pt barrier on thermal stability of Ti/Al/Pt/Au in ohmic contact with Si-implanted n-type GaN layers

We report the effect of the Pt barrier on the thermal stability of Ti/Al/Pt/Au in ohmic contact with Si-implanted n-type GaN layers. Ti/Al/Au (25/100/200 nm) and Ti/Al/Pt/Au (25/100/50/200 nm) multilayers were, respectively, deposited on as-implanted and recovered Si-implanted n-type GaN samples. The associated dependence of the specific contact resistance on the annealing time at various temperatures was compared. The long-term ohmic stability of a Ti/Al/Pt/Au multilayer in contact with a Si-implanted n-type GaN layer was much better than that of the Ti/Al/Au multilayer. This superior stability is attributed to the barrier function of the Pt interlayer. The Pt/Au bilayer can also passivate the propensity of oxidation for the conventional Ti/Al bilayer in contact with n-type GaN layers at elevated temperatures.     

异质结InP/InGaAs探测器欧姆接触温度特性研究

为了研究异质结InP/InGaAs探测器帽层的欧姆接触特性,采用Au/p-InP传输线模型(TLM),对比不同退火温度下的接触特性,在480℃、30 s的退火条件下实现室温比接触电阻为3.84×10~(-4)Ω·cm~2,同时,对欧姆接触的温度特性进行了研究,发现随着温度降低比接触电阻增加,在240~353 K温度范围内界面电流传输主要为热电子-场发射机制(TFE);240 K以下,接触呈现肖特基特性.利用扫描电子显微镜(SEM)和X射线衍射仪(XRD)分别对界面处的扩散程度和化学反应进行了分析,发现经过480℃、30 s退火后样品界面处存在剧烈的互扩散,反应产物Au_(10)In_3有利于改善Au/p-InP的接触性能.     

The thermal stability of lattice mismatched InGaAs grown on patterned GaAs

Patterning and etching substrates into mesas separated by trenches before the growth of mismatched (by about 1% or less) epitaxial layers considerably reduces the interface misfit dislocation density when the layer thickness exceeds the critical thickness. Such films are in a metastable state, since misfit dislocations allow the epitaxial layers to relax to an in-plane lattice parameter closer to its strain-free value. Thermal annealing (from 600 to 850° C) has been used to study the stability of these structures to explore the properties of the misfit dislocations and their formation. The misfit dislocation density was determined by counting the dark line defects at the InGaAs/GaAs interface, imaged by scanning cathodoluminescence. InGaAs epitaxial layers grown on patterned GaAs substrates by organometallic chemical vapor deposition possess a very small as-grown misfit dislocation density, and even after severe annealing for up to 300 sec at 800° C the defect density is less than 1500 cm⁻¹ for a In_0.04Ga_0.96As, 300 nm thick layer (about 25% of the dislocation density found in unpatterned material that has not been annealed). The misfit dislocation nucleation properties of the material are found to depend on the trench depth; samples made with deeper (greater than 0.5 μm) trenches are more stable. Molecular beam epitaxially grown layers are much less stable than the above material; misfit dislocations nucleate in much greater numbers than in comparable organo-metallic chemical vapor deposited material at all of the temperatures studied.     

Electrical and structural properties of GeMoW ohmic contact to an In0.5Ga0.5As cap layer on n-Type GaAs

The results of electrical and structural characterization of a GeMoW ohmic contact to n-type GaAs with a 100Å thick, In_0.5Ga_0.5As cap layer are presented. Electrical characterization demonstrates ohmic behavior over a wide annealing temperature range from 300 to 700°C. A minimum contact resistance of 0.176 Ω-mm was measured after furnace annealing at 500°C. The contact resistance is also insensitive to anneal time at 500°C. Structural characterization using secondary ion mass spectroscopy, Auger electron spectroscopy, and x-ray diffraction indicates excess In as a potential cause of increased contact resistance following 700°C annealing.     

Low resistive ohmic contact formation on surface treated-n-GaN alloyed at low temperature

Ohmic contacts to n-type GaN with low contact resistance were developed by (NH₄)₂S_x and KOH+(NH₄)₂S_x surface treatments prior to Ti/Al metal deposition. The lowest specific contact resistance of 3.0×10⁻⁶ Ω-cm² was obtained for Ti/Al contacts in an (NH₄)₂S_x-treated GaN layer alloyed at 300°C for 3 min. To obtain the lowest specific contact resistance for a low temperature alloy, the (NH₄)₂S_x treatment conditions for both (NH₄)₂S_x and KOH+(NH₄)₂S_x-treated n-GaN layers have been investigated and the mechanism for ohmic formation in low temperature alloys analyzed.     

Ni/Pd-based ohmic contacts to p-GaN through p-InGaN/p+-GaN contacting layers

Specific contact resistance \begin{document}$ {\rho }_{\mathrm{c}} $\end{document} to p-GaN was measured for various structures of Ni/Pd-based metals and thin (20–30 nm thick) p-InGaN/p⁺-GaN contacting layers. The effects of surface chemical treatment and annealing temperature were examined. The optimal annealing temperature was determined to be 550 °C, above which the sheet resistance of the samples degraded considerably, suggesting that undesirable alloying had occurred. Pd-containing metal showed ~35% lower \begin{document}$ {\rho }_{\mathrm{c}} $\end{document} compared to that of single Ni. Very thin (2–3.5 nm thick) p-InGaN contacting layers grown on 20–25 nm thick p⁺-GaN layers exhibited one to two orders of magnitude smaller values of \begin{document}$ {\rho }_{\mathrm{c}} $\end{document} compared to that of p⁺-GaN without p-InGaN. The current density dependence of \begin{document}$ {\rho }_{\mathrm{c}} $\end{document}, which is indicative of nonlinearity in current-voltage relation, was also examined. The lowest \begin{document}$ {\rho }_{\mathrm{c}} $\end{document} achieved through this study was 4.9 × 10^–5 Ω·cm² @ J = 3.4 kA/cm².     

Long-term stability of Ni-silicide ohmic contact to n-type 4H-SiC

The thermal stability of Ni₂Si/n-SiC ohmic contacts with Au overlayer without or with Ta-Si-N diffusion barrier was investigated after long anneals at 400 °C in air. Current-voltage characteristics, sheet resistance measurements, Rutherford backscattering spectrometry, X-ray diffraction and scanning electron microscopy were used to characterize the contacts before and after aging. It is shown that aging of Au/Ni₂Si/n-SiC contact at 400 °C for 50 h resulted in electrical failure, as well as complete contact degradation for 150 h due to interdiffusion/reaction processes in the contact. The Au/Ta₃₅Si₁₅N₅₀/Ni₂Si/n-SiC contact is thermally stable after 150 h of aging at 400 °C and has great potential for use in SiC-based devices for high-temperature operation.     

InAlAs/InGaAs/InP HEMT欧姆接触研究

应用Au/Ge/Ni系金属在InAlAs/InGaAs/InP HEMT上成功制作了良好的合金欧姆接触。采用WN和Ti双扩散阻挡层工艺优化欧姆接触,在样品上获得了最低9.01×10-8Ω.cm2的比接触电阻,对应的欧姆接触电阻为0.029Ω.mm。同时,在模拟后续工艺环境的20min250°C热处理后,器件的欧姆接触性能无显著变化,表明其具有一定的温度稳定性。     

Study of contact resistivity, mechanical integrity, and thermal stability of Ti/Al and Ta/Al ohmic contacts to n-type GaN

The annealing conditions and contact resistivities of Ta/Al ohmic contacts to n-type GaN are reported for the first time. The high temperature stability and mechanical integrity of Ti/Al and Ta/Al contacts have been investigated. Ta/Al (35 nm/115 nm) contacts to n-type GaN became ohmic after annealing for 3 min at 500°C or for 15 s at 600°C. A minimum contact resistivity of 5×10⁻⁶Ω cm² was measured after contacts were repatterned with an Al layer to reduce the effect of a high metal sheet resistance. Ti/Al and Ta/Al contacts encapsulated under vacuum in quartz tubes showed a significant increase in contact resistivity after aging for five days at 600°C. Cross section transmission electron microscopy micrographs and electrical measurements of aged samples indicate that the increased contact resistivity is primarily the result of degradation of the metal layers. Minimal reactions at the metal/GaN interface of aged samples were observed.     

p型GaN欧姆接触的研究进展

宽带隙的GaN作为半导体领域研究的热点之一,近年来发展得很快.p型GaN的欧姆接触问题一直阻碍高温大功率GaN基器件的研制.本文讨论了金属化方案的选择、表面预处理和合金化处理等几个问题,回顾了近年来p型GaN欧姆接触的研究进展.     

Electrical characteristics of thermally stable Ru and Ru/Au ohmic contacts to surface-treated p-type GaN

The electrical and thermal properties of Ru and Ru/Au ohmic contacts on two-step-surface-treated p-GaN have been investigated using current-voltage (I–V) measurements and Auger electron spectroscopy. It is shown that annealing at 700°C for 2 min in a flowing N₂ atmosphere improves the I–V characteristics of the contacts. For example, the annealed Ru and Ru/Au schemes produce a specific contact resistance of 3.4 (±0.9)×10⁻³ and 1.2 (±1.1)×10⁻³ Ωcm², respectively. It is also shown that annealing results in a large reduction (by ∼100 meV) in the Schottky barrier heights of the Ru and Ru/Au contacts, compared to the as-deposited ones. The electrical properties of the two-step-surface-treated Ru/Au contacts are compared with those of the conventionally treated contacts.     

Effects of rapid thermal annealing on ohmic contact of AIGaN/GaN HEMTs

Ohmic contacts with Ti/Al/Ti/Au source and drain electrodes on A1GaN/GaN high electron mobility transistors （HEMTs） were fabricated and subjected to rapid thermal annealing （RTA） in flowing N2. The wafer was divided into 5 parts and three of them were annealed for 30 s at 700, 750, and 800 ℃, respectively, the others were annealed at 750 ℃ for 25 and 40 s. Due to the RTA, a change from Schottky contact to Ohmic contact has been obtained between the electrode layer and the A1GaN/GaN heterojunction layer. We have achieved a low specific contact resistance of 7.41 × 10-6Ω cm2 and contact resistance of 0.54 Ω.mm measured by transmission line mode （TLM）, and good surface morphology and edge acuity are also desirable by annealing at 750 ℃ for 30 s. The experiments also indicate that the performance of ohmic contact is first improved, then it reaches a peak, finally degrading with annealing temperature or annealing time rising.     

Effects of rapid thermal annealing on ohmic contact of AlGaN/GaN HEMTs

工艺制作源漏电极为Ti/Al/Ti/Au,并在氮气气氛中对其进行快速退火,研究不同退火条件对欧姆接触的影响。具体实验过程如下：将溅射好源漏电极的外延片分为5部分,其中3片分别在700℃,750℃和800℃下快速退火30s,并相互对比得出最佳退火温度,实验结果发现750℃条件下欧姆接触最好;其余2片在750℃下分别退火25s和40s,并与前边实验750℃ 30s情况下欧姆接触比较,得出最佳退火时间为30s。我们使用传输线模式计算出电极与外延片的欧姆接触电阻率,在750℃ 30s的快速退火条件下得到最低欧姆接触电阻率为0.54 Ω mm,与其余条件下结果比较具有较好的表面形貌和边缘。从实验中我们也得到随着退火温度和退火时间的提高,欧姆接触电阻率先降低到达最低点然后开始升高的现象,为寻找GaN HEMT欧姆接触最佳条件提供了一定依据。     

Low resistance, thermally stable Au/Pt/Ti/WSiN ohmic contacts on n+-InGaAs/n-GaAs layer systems

The electrical properties of the ohmic contact systems Au/Pt/Ti/WSiN and Au/Pt/Ti to n⁺-InGaAs/GaAs layers grown by metalorganic vapor phase epitaxy were investigated and compared to each other. The thermal stability properties of these contact systems were characterized by accelerated stress tests at elevated temperatures and by complementary thin film x-ray diffraction analysis to evaluate the microstructural properties of degraded and nondegraded structures. The goal of these efforts was to develop stable, homogeneous emitter contacts for power heterojunction bipolar transistors. It was found that for both contact systems the best (specific) contact resistance R_c (ρ _c) is about 0.05 Ωmm (2 × 10⁻⁷ Ωcm²) in the as-deposited state. Au/Pt/Ti/WSiN contacts show no degradation after aging at 400°C for more than 20 h. This is in contrast to standard Au/Pt/Ti contacts which significantly degrade even after short time annealing at 400°C. The good long-time stability of the Au/Pt/Ti/WSiN system is related to the advantageous properties of the reactively sputtered WSiN barrier layer.     

Low-thermal-budget Au-free ohmic contact to an ultrathin barrier AlGaN/GaN heterostructure utilizing a micro-patterned ohmic recess

A pre-ohmic micro-patterned recess process,is utilized to fabricate Ti/Al/Ti/TiN ohmic contact to an ultrathin-barrier(UTB) AlGaN/GaN heterostructure,featuring a significantly reduced ohmic contact resistivity of 0.56 Ω.mm at an alloy temperat-ure of 550 ℃.The sheet resistances increase with the temperature following a power law with the index of +2.58,while the spe-cific contact resistivity decreases with the temperature.The contact mechanism can be well described by thermionic field emis-sion (TFE).The extracted Schottky barrier height and electron concentration are 0.31 eV and 5.52 × 1018 cm-3,which suggests an intimate contact between ohmic metal and the UTB-AlGaN as well as GaN buffer.A good correlation between ohmic trans-fer length and the micro-pattern size is revealed,though in-depth investigation is needed.A preliminary CMOS-process-compat-ible metal-insulator-semiconductor high-mobility transistor (MIS-HEMT) was fabricated with the proposed Au-free ohmic con-tact technique.     

金-锗系统欧姆接触制备研究

对于 Ga As MESFET和以 Ga As或 In P为衬底的 PHEMT的欧姆接触制备 ,虽均采用 Au-Ge- Ni系统 ,但其合金条件却因材料特性各异而不同。