The response of turbulent premixed flames to normal acoustic excitation

To model the thermo-acoustic excitation of flames in practical combustion systems, it is necessary to know how a turbulent flame front responds to an incident acoustic wave. This will depend partly on the way in which the burning velocity responds to the wave. In this investigation, the response of CH₄/air and CH₄/H₂/air mixtures has been observed in a novel flame stabilisation configuration, in which the premixture of fuel and air is made to decelerate under controlled conditions in a wide-angle diffuser. Control is provided by an annular wall-jet of air and by turbulence generators at the inlet. Ignition from the outlet of the diffuser allows an approximately flat flame to propagate downwards and stabilise at a height that depends on the turbulent burning velocity. When the flow is excited acoustically, the ensemble-averaged height oscillates. The fluctuations in flow velocity and flame height are monitored by phase-locked particle image velocimetry and OH-planar laser induced fluorescence, respectively. The flame stabilised against a lower incident velocity as the acoustic amplitude increased. In addition, at the lowest frequency of 52 Hz, the fluctuations in turbulent burning velocity (as represented by the displacement speed) were out-of-phase with the acoustic velocity. Thus, the rate of displacement of the flame front relative to the flow slowed as the flow accelerated, and so the flame movement was bigger than it would have been if the burning velocity had not responded to the acoustic fluctuation. With an increase in frequency to 119 Hz, the relative flame movement became even larger, although the phase-difference was reduced, so the effect on burning velocity was less dramatic. The addition of hydrogen to the methane, so as to maintain the laminar burning velocity at a lower equivalence ratio, suppressed the response at low amplitude, but at a higher amplitude, the effect was reversed.     

Resonance of a turbulent flame in a high-frequency acoustic wave

Resonance of a weakly turbulent flame in a high-frequency acoustic wave is obtained. Because of the resonance, an acoustic wave may increase noticeably the amplitude of flame wrinkles, and the respective increase in propagation velocity of the turbulent flame front becomes larger by a factor of 10-20. The effect of resonance is especially important for turbulent flames with realistic thermal expansion propagating in a closed burning chamber, which may account for considerable scattering of experimental results on turbulent flame velocity.     

Simulation of unsteady combustion in a solid-propellant rocket motor

Various regimes of combustion in end-burning-grain solid-propellant rocket motors were examined within the framework of the phenomenological theory of unsteady combustion. A system of equations capable of describing the interaction between the process of burning and acoustic waves was derived. A specific feature of the problem is that its formulation involves two characteristic times: the acoustic time and oscillation amplitude variation time. These characteristic times differ by about three orders of magnitude, a circumstance that requires a high accuracy of calculations. Based on the quadratic approximation in oscillation amplitude, a simpler method for solving the problem was proposed, according to which only the effects associated with the oscillation amplitude variation time are taken into account. Numerical results were obtained for the simplest model of propellant burning, which contains the minimum number of parameters and disregards entropy waves in the combustion products. The steady and unsteady regimes of burning were identified. In the latter case, nonlinear effects may generate shock waves in the combustion chamber.     

Impact of turbulence on flame brush development of acoustically excited rod-stabilized flames

Coherent structures, such as those arising from hydrodynamic instabilities or excited by thermoacoustic oscillations, can significantly impact flame structure and, consequently, the nature of heat release. The focus of this work is to study how coherent oscillations of varying amplitudes can impact the growth of the flame brush in a bluff-body stabilized flame and how this impact is influenced by the free stream turbulence intensity of the flow approaching the bluff body. We do this by providing external acoustic excitation at the natural frequency of vortex shedding to simulate a highly-coupled thermoacoustic instability, and we vary the in-flow turbulence intensity using perforated plates upstream of the flame. We use high-speed stereoscopic particle image velocimetry to obtain the three-component velocity field and we use the Mie-scattering images to quantify the behavior of the flame edge. Our results show that in the low-turbulence conditions, presence of high-amplitude acoustic excitation can cause the flame brush to exhibit a step-function growth, indicating that the presence of strong vortical structures close to the flame can suppress flame brush growth. This impact is strongly dependent on the in-flow turbulence intensity and the flame brush development in conditions with higher levels of in-flow turbulence are minimally impacted by increasing amplitudes of acoustic excitation. These findings suggest that the sensitivity of the flow and flame to high-amplitude coherent oscillations is a strong function of the in-flow turbulence intensity.     

Processing of thermogram sequences to determine the rotation rate of a vortex flame

We study vortex flame radiation in laboratory conditions. A fire torch was burning from a tank, which was fixed at the axis of uprising swirl airflow. Ethanol was used as a fuel. Processing of a sequence of thermograms of a swirling torch is described. The vortex flame revolutions were calculated using FFT of time pulsations of a signal from a thermal imaging system.     

高氧气浓度甲烷不稳定燃烧实验研究

采用无回火的急速混合管状燃烧技术,以二氧化碳和氧气的混合气体为氧化剂,基于CH~*自发光高速摄影图像及同步声压曲线,分析氧气浓度β=0.67的甲烷富氧燃烧特性。研究发现当量比0.6~1.0之间的火焰结构呈周期性变化,其频率与燃烧室内声压振荡频率一致,均为高频振荡。分析结果表明,燃烧器内的富氧燃烧振荡模式属于轴向声学共振。混合气体当量比由0.6增至1.0,热释率提高,热释率脉动与声压耦合增强,低频声压幅值减小,高频声压幅值增大,低频振动能量向高频振动能量转变,频谱特性由具有两个特征频率的周期性振荡转变为只有一个高频的周期振荡燃烧。     

Experimental characterization of onset of acoustic instability in a nonpremixed half-dump combustor

This paper reports work on a nonpremixed half-dump combustor, in which methane is injected at the backward-facing step, and mixes and burns with the air flowing past the step in the unsteady recirculation zone. The flow and geometric parameters are widely varied, to gradually change from conditions of low-amplitude noise to excitation of high-amplitude discrete tones. The purpose of the work is to focus on the transition from the former condition to the latter, and to mark the onset of instability. Dimensionless groups such as the Helmholtz and Strouhal numbers are formed based on the observed dominant frequencies, whose variation with the air flow Reynolds number is used to identify the oscillations as those due to the natural acoustic modes or the vortex shedding process. High-speed chemiluminescence imaging reveals shedding of vortical structures in the flame zone. With variation in the conditions, flow-acoustic lock-on and transition from one vortex shedding mode to another is marked by nonlinearity in the corresponding amplitude variations. Such conditions are identified as the onset of instability in terms of the ratio of the flow time scale to the acoustic time scale and mapped against the operating fuel-air equivalence ratio of the combustor.     

Analytical Interaction of the Acoustic Wave and Turbulent Flame

A modified resonance model of a weakly turbulent flame in a high-frequency acoustic wave is derived analytically. Under the mechanism of Darrieus-Landau instability, the amplitude of flame wrinkles, which is as functions of the expansion coefficient and the perturbation wave number, increases greatly independent of the stationary＇ turbulence. The high perturbation wave number makes the resonance easier to be triggered but weakened with respect to the extra acoustic wave. In a closed burning chamber with the acoustic wave induced by the flame itself, the high perturbation wave number is to restrain the resonance for a realistic flame.     

Combustion dynamics of inverted conical flames

An inverted conical flame anchored on a central bluff-body in an unconfined burner configuration features a distinctive acoustic response. This configuration typifies more complex situations in which the thermo-acoustic instability is driven by the interaction of a flame with a convective vorticity mode. The axisymmetric geometry investigated in this article features a shear region between the reactive jet and the surrounding atmosphere. It exhibits self-sustained oscillations for certain operating conditions involving a powerful flame collapse phenomenon with sudden annihilation of flame surface area. This is caused by a strong interaction between the flame and vortices created in the outer jet shear layer, a process which determines the amplitude of heat release fluctuation and its time delay with respect to incident velocity perturbations. This process also generates an acoustic field that excites the burner and synchronizes the vortex shedding mechanism. The transfer functions between the velocity signal at the burner outlet and heat release are obtained experimentally for a set of flow velocities fluctuations levels. It is found that heat release fluctuations are a strong function of the incoming velocity perturbation amplitude and that the time delay between these two quantities is mainly determined by the convection of the large scale vortices formed in the jet shear layer. A model is formulated, which suitably describes the observed instabilities.     

Effects of blending 2,5-dimethylfuran on the laminar burning velocity and ignition delay time of isooctane/air mixture

The prospects of 2,5-dimethylfuran (DMF) as a bio-derived fuel that can be blended with gasoline are believed to be impressive. However, the effects of blending DMF on the key combustion parameters like the laminar burning velocity and ignition delay time of gasoline/air mixture need to be studied extensively for the successful implementation of the fuel mixture in spark ignition engines. Therefore, a skeletal chemical kinetic mechanism, comprising of 999 reactions among 218 species, has been developed in the present work for this purpose. The proposed chemical kinetic model has been validated against a wide range of experimental data for the laminar burning velocity and ignition delay time of isooctane (representing gasoline), DMF and their blends. It has been found from the present study that the thermal diffusivity of the unburnt gas mixture changes by a very small amount from the corresponding value for the pure isooctane/air mixture when DMF is added. Unlike isooctane, the DMF molecule does not consume H radicals during its primary breakup. Therefore, the maximum laminar burning velocity increases marginally when 50% DMF is blended with isooctane due to the increased presence of H radicals in the flame. The negative temperature coefficient behaviour in the ignition delay time of the isooctane fuel vanishes when 30% DMF (v/v) is blended to it.     

A Study of premixed propagating flame vortex interaction

Experimental data is presented for the interaction between a propagating flame and a simple vortex flow field structure generated in the wake of solid obstacles. The interaction between gas movement and obstacles creates vortex shedding forming a simple flow field recirculation. The presence of the simple turbulent structure within the gas mixture curls the flame front increasing curvature and enhancing burning rate. A novel twin camera Particle Image Velocimetry, PIV, was employed to characterise the flow field recirculation and the interaction with the flame front. The technique allowed the quantification of the flame/vortex interaction. The twin camera technique provides data to define the spatial variation of both the velocity of the flow field and flame front. Experimentally obtained values of local flame displacement speed and flame stretch rate are presented for simple flame/vortex interactions.     

On nonlinear model equations for the response of premixed flames to acoustic like accelerations

The response of a dynamical flame model to imposed acoustic accelerations is studied analytically and numerically. Through linear stability analyses, two analytical approximations for the primary and the parametric stability boundaries are found. The approximation for the primary instability boundary is accurate for any periodic accelerations, in the limit of large acoustic frequencies. The critical acoustic amplitude u _a for Landau–Darrieus instability suppression is identified and found to depend only on the density contrast and the shape of the periodic acoustic stimuli. The proposed model evolution equation is next integrated numerically with various imposed acoustic accelerations; the primary and parametric flame responses are identified. It is shown analytically and numerically that in the presence of a fully developed, yet weakened by acoustics, Landau–Darrieus (or primary) instability the wrinkle amplitude and the mean flame speed oscillate at the same frequency as the acoustic stimuli; the threshold for suppression of primary instability by acoustic forcing is determined exactly. Increasing the acoustic amplitude allows the flame to respond parametrically to the acoustics. This response is characterised by troughs and crests interchanging their roles while the mean flame speed again oscillates with the same frequency as the acoustic stimuli and at twice that of wrinkle amplitude oscillations.     

Oscillatory cool flame combustion behavior of submillimeter sized n-alkane droplet under near limit conditions

This paper reports simulation results of oscillatory cool flame burning of an isolated, submillimeter sized n-heptane (n-C₇H₁₆) droplet in a selectively ozone (O₃) seeded nitrogen-oxygen (N₂-O₂) environments at atmospheric pressure. An evolutionary one-dimensional droplet combustion code encompassing relevant physics and detailed chemistry was employed to explore the roles of low-temperature chemistry, O₃ seeding, and dynamic flame structure on burning behaviors. For X_O2= 21% and a range of selective ozone seeding, near-quasi-steady cool flame burning is achieved directly (without requiring hot flame initiation and radiative extinction). Under low oxygen index conditions, but with significant O₃ seeding (X_O3 = 5%), a nearly quasi-steady cool flame is initially established that then transitions to a dynamically oscillating cool flame burning mode which continues until the droplet is completely consumed. It is found that the oscillation occurs as result of a initial depletion of fuel vapor-oxidizer layer evolving near the droplet surface and its dynamic re-establishment through liquid vaporization and vapor/oxidizer transport. A kinetic analysis indicates that the dynamic competition between the reaction classes- (a) degenerate chain branching and (b) chain termination/propagation - along with continuous fuel and oxygen leakage through the flame location contributes to an oscillatory burning phenomena of ever-increasing amplitude. Analysis based on single full-cycle of oscillatory burning shows that the reaction progression matrices (evolution of heat and species) for QOOH➔chain propagation/termination reactions (here, Q = C₇H₁₄-) directly scales with the gas phase temperature field. On the contrary, the QOOH➔degenerate branching reactions undergoes three distinct stages within the same oscillatory cycle. The coupled flame dynamics and kinetics suggest that in the oscillatory burning mode, kinetic processes dynamically cross through conditions characterizing the negative temperature coefficient (NTC) turnover temperature, separating low temperature and NTC kinetic regimes. In addition, a parametric study is conducted to determine the role of O₃ seeding level on the observed oscillation phenomena.     

Three-dimensional visualization of diffusion flame shapes under acoustic excitation using stereoscopic imaging and reconstruction technique

Stereoscopic imaging and reconstruction technique is introduced to reconstruct the flame structures that are subject to acoustic excitation. The laminar diffusion flame under investigation was created in a cylindrical tube and excited by a loudspeaker. Stereo images were taken at a shutter speed of 1/10000^th second using a ‘stereo camera’ and the depth cue of the flame structures along the camera viewing direction were then computed using machine vision methodology. By visualizing the computed three-dimensional flame models, as well as judging the corresponding attribute such as surface gradient, the understanding of the flame and acoustic wave interaction could be improved.     

Numerical simulation of flames as gas-dynamic discontinuities

The dynamics of thin premixed flames is computationally studied within the context of a hydrodynamic theory. A level-set method is used to track down the flame, which is treated as a free-boundary interface. The flow field is described by the incompressible Navier–Stokes equations, with different densities for the burnt and unburnt gases, supplemented by singular source terms that properly account for thermal expansion effects. The numerical scheme has been tested on several benchmark problems and was shown to be stable and accurate. In particular, the propagation of a planar flame front and the dynamics of hydrodynamically unstable flames were successfully simulated. This includes recovering the planar front in narrow domains, the Darrieus–Landau linear growth rate for long waves of small amplitude, and the nonlinear development of cusp-like structures predicted by the Michelson–Sivashinsky equation for a small density change. The stationary flame of a Bunsen burner with uniform and parabolic outlet flows were also simulated, showing in particular a careful mapping of the flow field. Finally, the evolution of a hydrodynamically unstable flame was studied for finite amplitude disturbances and realistic values of thermal expansion. These results, which constitute one of the main objectives of this study, elucidate the effect of thermal expansion on flame dynamics.     

Structure and dynamic response of radiative diffusion flames

Nitrogen-diluted hydrogen burning in air is modeled numerically using a constant density and one-step reaction model in a plane two-dimensional counterflow configuration. An optically thin assumption is used to investigate the effects of radiation on the dynamics, structure, and extinction of diffusion flames. While there exist dual steady-state extinction limits for the 1D radiative flame response, it is found that as the 1D radiative extinction point is approached the 1D low-stretch diffusion flame exhibits oscillatory response, even with sub-unity Lewis number fuel. These radiation-induced limit cycle oscillations are found to have increasing amplitude and decreasing frequency as the stretch rate is reduced. Flame oscillation eventually leads to permanent extinction at the stretch rate which is larger than the steady-state radiative extinction value. Along the 1D radiative response curve, the transition from 1D flame to 2D structure and the differences in the resulting 2D flame patterns are also examined using a variety of initial profiles, with special emphasis on the comparison of using the initial profiles with and without a flame edge. Similar to the previous studies on the high-stretch adiabatic edge flames using the same configuration, the high-stretch radiative flames are found to resist 1D blow-off quenching through various 2D structures, including propagating front and steady cellular flames for initial profiles with and without flame edges. For all initial profiles studied, the low-stretch radiative flames are also found to exhibit different 2D flame phenomena near the 1D radiative extinction limit, such as transient cellular structures, steady cellular structures, and pulsating ignition fronts. Although the results demonstrate the presence of low-stretch and high-stretch 2D bifurcation branches close to the corresponding 1D extinction limits irrespective of the initial profile used, particular 2D flame structures in certain stretch rate range are initial profile dependent. The existence of two-dimensional flame structures beyond the 1D steady-state radiative extinction limit suggests that the flammable range is expanded as compared to that predicted by the 1D model. Hence, multi-dimensional flame patterns need to be accounted for when determining the flammability limits for a given system.     

Nonlinear hydrodynamic and thermoacoustic oscillations of a bluff-body stabilised turbulent premixed flame

Turbulent premixed flames often experience thermoacoustic instabilities when the combustion heat release rate is in phase with acoustic pressure fluctuations. Linear methods often assume a priori that oscillations are periodic and occur at a dominant frequency with a fixed amplitude. Such assumptions are not made when using nonlinear analysis. When an oscillation is fully saturated, nonlinear analysis can serve as a useful avenue to reveal flame behaviour far more elaborate than period-one limit cycles, including quasi-periodicity and chaos in hydrodynamically or thermoacoustically self-excited system. In this paper, the behaviour of a bluff-body stabilised turbulent premixed propane/air flame in a model jet-engine afterburner configuration is investigated using computational fluid dynamics. For the frequencies of interest in this investigation, an unsteady Reynolds-averaged Navier–Stokes approach is found to be appropriate. Combustion is represented using a modified laminar flamelet approach with an algebraic closure for the flame surface density. The results are validated by comparison with existing experimental data and with large eddy simulation, and the observed self-excited oscillations in pressure and heat release are studied using methods derived from dynamical systems theory. A systematic analysis is carried out by increasing the equivalence ratio of the reactant stream supplied to the premixed flame. A strong variation in the global flame structure is observed. The flame exhibits a self-excited hydrodynamic oscillation at low equivalence ratios, becomes steady as the equivalence ratio is increased to intermediate values, and again exhibits a self-excited thermoacoustic oscillation at higher equivalence ratios. Rich nonlinear behaviour is observed and the investigation demonstrates that turbulent premixed flames can exhibit complex dynamical behaviour including quasiperiodicity, limit cycles and period-two limit cycles due to the interactions of various physical mechanisms. This has implications in selecting the operating conditions for such flames and for devising proper control strategies for the avoidance of thermoacoustic instability.     

着火油罐燃烧特性的理论分析

本文利用自行建立的油罐火灾燃烧特性通用模型,计算得到了燃烧速度、火焰高度,火焰跳动频率和平均温度等油罐燃烧特性的变化规律,并深入探讨了油品燃烧速度在油罐直径、风速、环境温度和油位等因素影响下的变化趋势。为了验证理论计算的准确性,将计算结果与汽油和柴油储罐的燃烧实验数据进行了对比,获得了较为满意的结果。