上游水库水体中氨氮、亚硝酸盐氮、硝酸盐氮、总氮的测定和关系探究

采用紫外分光光度法测定上游水库固定监测点位近两年采集样品的总氮、硝酸盐氮、氨氮、亚硝酸盐氮含量.对测试结果进行分析比较,探讨了上游水库水中总氮、硝酸盐氮、氨氮、亚硝酸盐氮的关系,从而为上游水库水质数据分析和综合评价提供一定参考.     

非金属元素氮的同素异形体概述

依据全氮物质的研究进展对非金属氮元素的同素异形体进行了归纳,按结构不同可将其分为分子氮、聚合氮、金属氮和原子簇氮等4类.分别对各种同素异形体的组成、结构、存在与合成进展以及应用进行了综合介绍,为丰富氮元素的教学和扩展应用研究提供重要素材.     

Determination of Total Nitrogen,Ammonia, and Nitrite in River Water by Near-infrared Spectroscopy and Chemometrics

Total nitrogen, ammonia nitrogen, and nitrite nitrogen were determined in river water during intermittent aeration by near-infrared spectroscopy with a back-propagation neural network. Near-infrared spectra were obtained for 138 samples. A total of 116 samples were used as the calibration set and the remainder as the test set. The spectral region was from 4000 to 12,500?cm^?1. Principal component analysis was used as a preprocessing method of the near-infrared spectra to eliminate redundant information. The six principal components were extracted through principal component analysis. Back-propagation neural network models of total nitrogen, ammonia nitrogen, and nitrite nitrogen showed that the correlation coefficients were 0.9816, 0.9783, and 0.9562, respectively, with root-mean-square error of cross validation values of 0.04735, 0.03689, and 0.03766. The results of the back-propagation neural network models of total nitrogen, ammonia nitrogen, and nitrite nitrogen indicated that the correlation coefficients were 0.9752, 0.9690, and 0.9524, respectively, with root-mean-square errors of prediction equal to 0.05763, 0.04537, and 0.04157. This study showed that the described approach accurately determined total nitrogen, ammonia nitrogen, and nitrite nitrogen. The concentrations of total nitrogen, ammonia nitrogen, and nitrite nitrogen were 0.64–54.25, 0.57–45.04, and 0.05–31.40?mg?·?L^?1 in river water, respectively.     

Reactions of nitrile oxides with nitrogen oxides. 2. Reactions with nitrogen monoxide and nitrogen sesquioxide

We have studied the reactions of aromatic nitrile oxides with nitrogen monoxide and nitrogen sesquioxide. It was shown that nitrogen monoxide removes an oxygen atom from the nitrile oxide with formation of the corresponding nitrile and nitrogen dioxide. The reaction products with nitrogen sesquioxide are formed as a result of reactions of the nitrile oxide with nitrogen monoxide and nitrogen tetroxide.For previous communication, see [1].Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 7, pp. 1623–1625, July, 1990.     

Fermentation Characteristics of <Emphasis Type="Italic">Mortierella alpina</Emphasis> in Response to Different Nitrogen Sources

The fermentation characteristics of Mortierella alpina were investigated in response to various nitrogen sources. Influences on nitrogen source and glucose uptake rate, mycelial morphology of M. alpina, and pH of medium in relation to different nitrogen sources were discussed. Effects of different nitrogen sources on cell growth, fatty acid composition, arachidonic acid (ARA), and total lipid concentration were also evaluated. It revealed that the maximum nitrogen source uptake ratio was obtained when corn steep liquor was used as nitrogen source. When yeast extract was used as the sole nitrogen source, glucose was completely exhausted at the end of fermentation. The maximum dry cell weight obtained from medium with yeast extract as nitrogen source had the highest total lipid concentration. Sodium nitrate was the favorable nitrogen source for ARA accumulation, and the highest ARA percentage in total fatty acids was obtained, 35.9%. Urea was identified as the favorable nitrogen source for ARA production, the highest ARA concentration obtained from urea was 5.8 g/l. Compared with inorganic nitrogen sources, organic nitrogen compounds are favorable for both cell growth and total lipids accumulation.     

High-performance ion chromatography assessment of inorganic and organic nitrogen fractions in potatoes

A new high-performance ion chromatography assay for organic and inorganic nitrogen analysis has been proposed and examined. In the devised protocol, inorganic sample constituents were measured after ultrasonically assisted water extraction. The amine and amide nitrogen content was assessed after modified Kjeldahl digestion and determined as NH₄⁺, and the total nitrogen content was quantified as NO₃⁻ after microwave-facilitated digestion. Finally, the nitro, azo, azoxy nitrogen was calculated by comparison of the total nitrogen content and all measured nitrogen species. The detection limits of the measured ions were 2.0, 0.82 and 0.17 mg L⁻¹ for nitrate, nitrite and ammonium, respectively. For samples of potatoes, the average shares of the nitrogen species found in the total nitrogen content were: 0.83% of nitrate nitrogen, <0.03% of nitrite nitrogen, 2.1% of ammonium nitrogen, 71% of nitro, azo, azoxy nitrogen, and 26% of amine, amide nitrogen. We expect the method to be applicable to different vegetable samples. The quality of the results obtained was verified by analyzing certified reference material and comparing to another analytical method.     

催化柴油中氮化物分布的气相色谱-原子发射光谱分析方法的研究

建立了催化柴油馏分中各种氮化物类型分布的气相色谱-原子发射光谱(GC-AED)分析方法,考察了色谱条件和不同的试剂气压力对各种氮化物分离和检测灵敏度的影响,定性(或归类)了某典型催化柴油中的73个氮化物,计算了程升条件下各种氮化物的保留指数,为不同实验室的定性比较提供了依据。以峰面积对质量浓度作图,氮化物在2.0~600 mg/L浓度范围内,AED检测器对不同氮化物有良好的线性响应,线性相关系数达0.998。几种氮化物(吲哚、1-甲基吲哚、C2-吲哚、咔唑、1-甲基咔唑、1,8-二甲基咔唑)峰面积的相对标     

催化柴油中含氮化合物类型分布的气相色谱分析方法

建立了催化柴油馏分中各种含氮化合物类型分布的气相色谱-氮化学发光检测分析方法,考察了色谱条件对各种含氮化合物分离的影响。采用Al2O3柱富集催化柴油中的含氮化合物,辅以气相色谱-质谱检测器以及部分含氮化合物标准样品对某催化柴油中的80多个含氮化合物进行了定性(或归类)。以N,N-二甲基苯胺、三丁基胺、喹啉、吲哚、咔唑作为标准样品,考察了各种含氮化合物在氮化学发光检测器上的响应,以吲哚为参照,各含氮化合物的相对响应因子为0.97～1.07,表明含氮化合物的响应与其类型无关。氮的质量浓度在1.0～600 mg/L范围内,含氮化合物的峰面积与质量浓度有良好的线性响应,线性相关系数达0.998。催化柴油中几种含氮化合物(吲哚、C2-吲哚、咔唑、1-甲基咔唑、1,8-二甲基咔唑)含量测定值的相对标准偏差均小于8%。当信噪比(S/N)为3时,测得咔唑氮的检出限为1.0 mg/L。苯胺、喹啉、吲哚、咔唑等4种含氮化合物的加标回收率为89.5%～99.8%。该方法可用于不同来源和不同加工工艺的柴油馏分中各种含氮化合物类型分布的研究。     

氮气笼型水合物的激光拉曼光谱

在253K和16MPa的压力下,于实验室内合成了氮气水合物,用显微共焦拉曼光谱对其N-N和O-H键伸缩振动的光谱特征进行了研究．结果表明,氮气水合物中的N-N和O—H键的拉曼峰分别为2322．4和3092．1cm^-1,与天然的空气水合物中的数据十分接近．另外,还测定了液氮和溶解于水中的氮分子中N—N键的拉曼峰值,分别为2326．6和2325．0cm^-1．氮气笼型水合物分解的拉曼谱图表明,氮分子同时进入水合物的大笼和小笼中,但由于氮分子在大、小笼中的环境氛围十分接近,其拉曼位移相差不大,故拉曼谱图只能显示N—N键伸缩振动一个峰．     

Etudes par RMN en serie heterocyclique–III. Non-equivalence magnetique et inversion de l'azote dans une serie d'heteocycles pentagonaux diazotes,pyrazolines-2 et 3, pyrazolidines et pyrazolidones

The non-equivalence of ethyl, benzyl and isopropyl groups fixed on nitrogen atoms in 2-and 3-pyrazolines, pyrazolidines and pyrazolidones depends on the assymetry existing in the molecule. The asymmetric centres are either a ring carbon atom, a quaternary nitrogen atom (protonation, quaternarization) or a tertiary nitrogen atom (slow nitrogen inversion). The nitrogen inversion process was observed only in the case of pyrazolidines (possibility of inversion at the two adjacent nitrogens) and of pyrazolidones (inversion of the ‘non-amidic’ nitrogen). The inversion is temperature-dependent and is affected by substituents.     

Determination of Nitrogen in Duplex Stainless Steels by EPMA

 We describe the quantitative determination of low nitrogen contents (< 1 %wt) in highly-alloyed, duplex stainless steels by EPMA using a calibration curve. Five monophasic stainless steels with various nitrogen concentrations were used for the calibration curve, namely, three highly alloyed steels prepared in the laboratory, with nitrogen contents 0.066, 0.565 and 1.016 %wt and two industrial alloys with nitrogen concentrations 0.174 %wt and 0.023 %wt. For these samples, the plot of nitrogen X-ray intensities versus nitrogen contents exhibited an acceptable linear relationship. Average nitrogen contents of the analysed duplex alloys were found to vary in the range < 0.045–0.07 %wt in ferrite and 0.52–0.77 %wt in austenite. These results suggest that the nitrogen solubility limit in ferrite has been reached; on the other hand, nitrogen solubility in austenite increases due to the high manganese and low nickel contents.     

气相色谱-氮化学发光检测法分析催化汽油中含氮化合物类型的分布

建立了催化汽油馏分中各种含氮化合物类型分布的气相色谱-氮化学发光检测分析方法,考察了各种色谱条件对含氮化合物分离的影响。采用化学预处理的方法浓缩了催化汽油中的含氮化合物,并结合气相色谱-质谱检测以及部分含氮化合物标准样品,对某催化汽油中的20多个含氮化合物进行了定性(或归类)。催化汽油中几种主要含氮化合物(苯胺、2-甲基苯胺、二甲基苯胺)含量测定值的相对标准偏差(RSD)均不大于2.5%。当信噪比(S/N)为3时,苯胺氮的检出限为1.0 mg/L。该方法可用于不同来源和不同加工工艺的汽油馏分中各种含氮化合物类型分布的研究。     

Characterisation and quantification of organic phosphorus and organic nitrogen components in aquatic systems: a review

This review provides a critical assessment of knowledge regarding the determination of organic phosphorus (OP) and organic nitrogen (ON) in aquatic systems, with an emphasis on biogeochemical considerations and analytical challenges. A general background on organic phosphorus and organic nitrogen precedes a discussion of sample collection, extraction, treatment/conditioning and preconcentration of organic phosphorus/nitrogen from sediments, including suspended particulate matter, and waters, including sediment porewaters. This is followed by sections on the determination of organic phosphorus/nitrogen components. Key techniques covered for organic phosphorus components are molecular spectrometry, atomic spectrometry and enzymatic methods. For nitrogen the focus is on the measurement of total organic nitrogen concentrations by carbon hydrogen nitrogen analysis and high temperature combustion, and organic nitrogen components by gas chromatography, high-performance liquid chromatography, gel electrophoresis, mass spectrometry, nuclear magnetic resonance spectrometry, X-ray techniques and enzymatic methods. Finally future trends and needs are discussed and recommendations made.     

An apparatus for the emission spectrometric determination of nitrogen released into an argon gas stream by chemical reactions in solution

An apparatus has been constructed primarily for determination of nitrogen released from steels on reaction with organic solvent-halogen mixtures. The nitrogen is collected in a coil and then flushed with argon through a spectroanalyser that is selective to nitrogen and coupled to a recorder and integrator. The integrated signal is linearly related to the mass of nitrogen produced. The apparatus has been tested by determining the yield of nitrogen produced by reaction of hydrazine with a large excess of hypobromite in aqueous solution. For ten 57-microg amounts of hydrazine the average yield of nitrogen was 99%, with a relative standard deviation of 2.4%.     

The Chemical Behavior of Active Nitrogen

Active nitrogen, which is formed on passage of an electric discharge through a stream of nitrogen, is detected by a characteristic yellow afterglow. It can be determined quantitatively, e.g. by gas phase “titration” with nitric oxide. Active nitrogen reacts with many chemical elements, as well as with organic and inorganic compounds. Although nitrogen atoms are responsible for many of the reactions of active nitrogen, electronically excited molecules also play a role.     

原位掺杂法制备氮掺杂中孔炭及乙炔氢氯化反应性能

聚氯乙烯(PVC)是世界五大工程塑料之一,在工业、农业、建筑、电力及通信等领域有着非常广泛的应用.氯乙烯(VCM)作为合成 PVC的单体,其生产工艺以源于煤化工路线的乙炔氢氯化法工艺为主,但是该工艺目前采用的是氯化汞催化剂,存在较为严重的环境污染问题.开发新型无汞催化剂成为电石法生产 VCM亟待解决的问题.氮掺杂炭基非金属催化剂成本低廉,制备简单,在诸多反应中展现了较好的性能,成为近几年多相催化领域的一个研究热点,在乙炔氢氯化反应中也具有较好的活性,但是对活性中心的鉴别及制备方法的研究还有待深入.本文报道了一种一步原位尿素掺杂氮的中孔炭的制备方法,采用氮气吸附-脱附、高分辨透射电子显微镜、元素分析和X射线光电子能谱(XPS)等表征手段研究了氮掺杂中孔炭的结构、氮含量及存在形式,并与两步尿素改性方法做了对比,探究了氮掺杂形式与中孔炭乙炔氢氯化反应性能之间的关系,同时考察了尿素用量对氮掺杂中孔炭的氮含量和存在形式的影响.元素分析结果表明,原位合成法能有效地将氮掺杂进骨架中,随着制备过程中尿素用量增加,得到的氮掺杂中孔炭中的氮含量增加,可达3.6 wt%.后处理法的掺氮效果较差,材料氮含量仅为0.2 wt%. XPS测试进一步表明,一步法原位法可以得到石墨型氮占据主导地位的氮掺杂中孔炭,石墨型氮约占70%左右,后处理制备的氮掺杂中孔炭中石墨氮、吡啶氮和吡咯氮三种形式含量相差不大.对不同方法合成的氮掺杂介孔炭的乙炔氢氯化反应催化性能进行了评价,结果显示,无论是原位合成还是后处理制备的氮掺杂中孔炭,其活性均比中孔炭得到一定提升.氮的引入能有效提高材料的乙炔氢氯化反应性能.原位合成法制备的氮掺杂中孔炭在乙炔氢氯化反应中的催化性能远高于后处理法.对于原位合成的氮掺杂中孔炭,在一定范围内,随着氮含量的增加,催化活性提高,但当尿素用量过高时,虽然氮含量增加,催化活性却有所下降,这归因于孔结构坍塌和比表面积下降.     

Advanced Non-metallic Catalysts for Electrochemical Nitrogen Reduction under Ambient Conditions

The electrochemical reduction of nitrogen into ammonia under ambient conditions is a potential strategy for sustainable ammonia production. At present, one of the main research directions in the field of electrochemical nitrogen fixation is to improve the current efficiency and ammonia yield by developing efficient nitrogen reduction catalysts. To optimise the selectivity and catalytic activity of nitrogen reduction catalysts more efficiently, herein, we systematically summarise the progress of research on nitrogen reduction catalysts in recent years and present some general catalyst design strategies. Considering that it is difficult for metal-based catalysts to balance the competitive reactions of nitrogen activation and hydrogen evolution, we discuss in detail the advantages and application prospects of non-metallic catalysts in electrochemical nitrogen fixation. Moreover, both the design strategy of surface or interface defects, and how this atomic-level control of functionalisation helps to promote selectivity and catalytic activity are also discussed by theoretical and experimental electrochemistry. On this basis, we also discussed the future development direction, opportunities and challenges of nitrogen reduction electrocatalysts.     

A Comparison of PE Surfaces Modified by Plasma Generated Neutral Nitrogen Species and Nitrogen Ions

The surface modification of polyethylene (PE) by neutral nitrogen species (ground and excited state N₂ as well as atomic N; modified nitrogen plasma treatment) has been compared to the effect of nitrogen ion bombardment using X-ray Photoelectron Spectroscopy (XPS) and contact angle measurements. XPS results indicate that a greater nitrogen concentration was grafted during the modified nitrogen plasma treatment of PE, an effect that was attributed to surface sputtering during ion beam modification. The distribution of nitrogen-containing functionalities was strongly dependent upon the treatment strategy; the modified nitrogen plasma treatment lead predominantly to imine groups being formed at the PE surface, while amine groups were the dominant species produced during ion beam modification. The presence of electron irradiation during the modified nitrogen plasma treatment of PE did not modify the rate of nitrogen incorporation or change the nature of N-containing functional groups produced but did lead to a systematic decrease in contact angle.     

Synthesis and properties of hypervalent electron-rich pentacoordinate nitrogen compounds

Isolation and structural characterization of hypervalent electron-rich pentacoordinate nitrogen species have not been achieved despite continuous attempts for over a century. Herein we report the first synthesis and isolation of air stable hypervalent electron-rich pentacoordinate nitrogen cationic radical (11-N-5) species from oxidation of their corresponding neutral (12-N-5) species. In the cationic radical species, the nitrogen centers adopt a trigonal bipyramidal geometry featuring a 3-center-5-electron hypervalent attractive interaction. The combination of single crystal X-ray diffraction analysis and computational studies revealed weak N–O interactions between the central nitrogen cation and oxygen atoms. This successful design strategy and isolation of air-stable pentacoordinate hypervalent nitrogen species allow further investigations on reactivity and properties resulting from these unusually weakly coordinating interactions in nitrogen compounds.

Structural characterization of hypervalent electron-rich pentacoordinate nitrogen species has long been a synthetic challenge. Here we report the first nitrogen cationic radical (11-N-5) species featuring a weak hypervalent 3c-5e interaction.     

Modular Functionalization of Metal-Organic Frameworks for Nitrogen Recovery from Fresh Urine**

Nitrogen recovery from wastewater represents a sustainable route to recycle reactive nitrogen (Nr). It can reduce the demand of producing Nr from the energy-extensive Haber-Bosch process and lower the risk of causing eutrophication simultaneously. In this aspect, source-separated fresh urine is an ideal source for nitrogen recovery given its ubiquity and high nitrogen contents. However, current techniques for nitrogen recovery from fresh urine require high energy input and are of low efficiencies because the recovery target, urea, is a challenge to separate. In this work, we developed a novel fresh urine nitrogen recovery treatment process based on modular functionalized metal–organic frameworks (MOFs). Specifically, we employed three distinct modification methods to MOF-808 and developed robust functional materials for urea hydrolysis, ammonium adsorption, and ammonia monitoring. By integrating these functional materials into our newly developed nitrogen recovery treatment process, we achieved an average of 75 % total nitrogen reduction and 45 % nitrogen recovery with a 30-minute treatment of synthetic fresh urine. The nitrogen recovery process developed in this work can serve as a sustainable and efficient nutrient management that is suitable for decentralized wastewater treatment. This work also provides a new perspective of implementing versatile advanced materials for water and wastewater treatment.