Synthesis and photocatalytic property of SnO2/TiO2 nanotubes composites

SnO2/TiO2 nanotubes composite photocatalysts with different SnO2 contents were successfully synthesized by means of a simple solvothermal process. The synthesized products were characterized physically by X-ray diffraction (XRD) and high-resolution transmission electron microscope (HRTEM). The composite photocatalysts can not only make the target pollutant, methylene blue (MB), adsorbed at a high concentration level around the surface of the composites but also decrease the recombination rate of electron-hole pairs so as to achieve good photocatalytic performance. The effect of SnO2 contents on the photocatalytic activities of the composites was also investigated. The results showed that the SnO2/TiO2 nanotubes composite photocatalyst with 5 wt.% SnO2 loading had the highest photocatalytic efficiency.     

Photocatalytic degradation of aqueous propoxur solution using TiO2 and Hbeta zeolite-supported TiO2

Photocatalytic activity of TiO2 and zeolites supported TiO2 were investigated using propoxur as a model pollutant. Hbeta, HY and H-ZSM-5 zeolites were examined as supports for TiO2. Hbeta was chosen as the TiO2 support based on the adsorption capacity of propoxur on these zeolites (Hbeta>HY=H-ZSM-5). TiO2/Hbeta photocatalysts with different wt.% were prepared and characterized by XRD, FT-IR and BET surface area. The progress of photocatalytic degradation of aqueous propoxur solution using TiO2 (Degussa P-25) and TiO2 supported on Hbeta zeolite was monitored using TOC analyzer, HPLC and UV-vis spectrophotometer. The degradation of propoxur was systematically studied by varying the experimental parameters in order to achieve maximum degradation efficiency. The initial rate of degradation with TiO2/Hbeta was higher than with bare TiO2. TOC results revealed that TiO2 requires 600min for complete mineralization of propoxur whereas TiO2/Hbeta requires only 480min. TiO2/Hbeta showed enhanced photodegradation due to its high adsorption capacity on which the pollutant molecules are pooled closely and hence degraded effectively.     

Fabrication of TiO2/Ti electrode by laser-assisted anodic oxidation and its application on photoelectrocatalytic degradation of methylene blue

A TiO2/Ti mesh electrode by laser calcination was prepared in this article. The resulting TiO2 film was investigated by X-ray diffraction (XRD), atomic force microscopy (AFM) and electrochemical impedance spectroscopy (EIS), and it illuminated that the prepared electrode mainly consisted of anatase TiO2 nanoparticles on its surface and exhibited a superior photocatalytic activity. The photodegradation of methylene blue (MB) using the proposed electrode under different experimental conditions was investigated in terms of both UV absorbance at 664 nm and chemical oxygen demand (COD) removal. The electrical bias applied in photoelectrocatalytic (PEC) oxidation was also studied. The experimental results showed that under the optimal potential of +0.50 V (versus SCE), UV absorbance and COD removal during the photodegradation of MB by the proposed TiO2/Ti mesh electrode were 97.3% and 87.0%, respectively. Through the comparison between photocatalytic (PC) oxidation and photoelectrocatalytic (PEC) oxidation, it was found that PEC oxidation was a convenient and effective way to mineralize the organic matters and that laser-treated photoelectrode exceeded the oven-treated one.     

Photoinduced hydroxyl radical and photocatalytic activity of samarium-doped TiO(2) nanocrystalline

Sm(3+)-doped TiO(2) nanocrystalline has been prepared by sol-gel auto-combustion technique and characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) method, and also UV-vis diffuse reflectance spectroscopy (DRS). These Sm(3+)-doped TiO(2) samples were tested for methylene blue (MB) decomposition and *OH radical formation. The analysis of *OH radical formation on the sample surface under UV irradiation was performed by fluorescence technique with using terephthalic acid, which readily reacted with *OH radical to produce highly fluorescent product, 2-hydroxyterephthalic acid. It was observed that the presence of Sm(3+) ion as a dopant significantly enhanced the photocatalytic activity for MB degradation under UV light irradiation because both the larger specific surface area and the greater the formation rate of *OH radical were simultaneously obtained for Sm(3+)-doped TiO(2) nanocrystalline. The adsorption experimental demonstrated that Sm(3+)-TiO(2) had a higher MB adsorption capacity than undoped TiO(2) and the adsorption capacity of MB increased with the increase of samarium ion content. The results also indicated that the greater the formation rate of *OH radical was, the higher photocatalytic activity was achieved. In this study, the optimum amount of Sm(3+) doping was 0.5 mol%, at which the recombination of photo-induced electrons and holes could be effectively inhibited, the highest formation rate of *OH radicals was, and thereby the highest photocatalytic activity was achieved.     

Photo-catalytic film deposition by atmospheric TPCVD

TiO₂ film were deposited by atmospheric thermal plasma chemical vapor deposition (TPCVD) method to investigate the rapid process for functional film deposition. The experiment was conducted under the condition where working gas was Ar, working gas flow rate was 20 l/min, deposition distance was varied from 30 to 200 mm and spraying time was 10 min. Ethanol diluted titanium tetra buthoxide was used as starting material. Consequently, even in this process TiO₂ films including anatase could be deposited, and the results of wettability and methylene blue decoloration testings suggest that the TiO₂ films have good photo-catalytic property. Besides, by using extension nozzle, columnar structure film could be deposited due to a perfect starting material vaporization. From these results, the proposed process seemed to be highly promising for the rapid formation of functional thin films.     

Photocatalytic activity of TiO2 doped with boron and vanadium

Boron (B)- and vanadium (V)-doped TiO(2) photocatalysts were synthesized using modified sol-gel reaction processes and characterized by X-ray diffraction (XRD), Raman spectroscopy and N(2) physisorption (BET). The photocatalytic activities were evaluated by monitoring the degradation of methylene blue (MB). The results showed that the materials possess high surface area. The addition of B favored the transformation of anatase to rutile, while in the presence of V, anatase was the only phase detected. The MB degradation on V-doped TiO(2) was significantly affected by the preparation method. In fact while the presence of V in the bulk did not influence strongly the photoreactivity under visible irradiation, an increase of surface V doping lead to improved photodegradation of MB. The degradation of MB dye indicated that the photocatalytic activities of TiO(2) increased as the boron doping increased, with high conversion efficiency for 9mol% B doping.     

A study of parameter setting and characterization of visible-light driven nitrogen-modified commercial TiO2 photocatalysts

An optimal condition applied to the Taguchi method with an L(9) orthogonal array for preparing a visible-light driven nitrogen-modified TiO(2) (N-TiO(2)) photocatalyst by a simple hydrolysis method has been examined for material characteristics and a photodecolorization test of methyl blue (MB) under various visible light source (fluorescent and blue LED lamps) irradiations. Results of the material characterization showed that the absorption of prepared N-TiO(2) powder exhibited a significant extension into visible light regimes with an optical bandgap (Eg) of around 2.96 eV, which subsequently improved the visible-light photocatalytic activity of N-TiO(2) samples. The superior photocatalytic properties, the pseudo first-order reaction rate constants (k) and photodecolorization efficiency (η%) of a N-TiO(2) photocatalyst during the photodecolorization test of methyl blue (MB) under two different visible light irradiations were very evident compared to those for pure TiO(2). For photodecolorization of practical dyeing from the waste water from the dyeing and finishing industry, a higher photodecolorization efficiency of N-TiO(2) powder toward Direct blue-86 (DB-86) (Direct Fast Turquoise Blue GL) dye was also achieved.     

Degradation of di-n-butyl phthalate using photoreactor packed with TiO2 immobilized on glass beads

This study evaluated the performance of a photoreactor packed with TiO2/glass, TiO2 immobilized on glass beads, initiated by UV irradiation, denoted as UV/TiO2/glass, to decompose di-n-butyl phthalate (DBP) in an aqueous solution. The photodegradation rate of DBP by this UV/TiO2/glass process was found to obey pseudo first-order kinetics represented by the Langmuir-Hinshelwood model. The experimental results of this study show that the influence of pH value of an aqueous solution to reaction rate was negligible at the pH values 4.5-9. The effect of cations on the photodegradation rate of DBP reveals that the larger the charge and size of cations contained, the more the inhibition of reaction rate increased. The UV/TiO2/glass process yielded a 75% degradation efficiency of DBP with initial concentration of 5 mg L(-1) at 80 min reaction time.     

Fabrication of carbon-modified TiO2 nanotube arrays and their photocatalytic activity

TiO₂ nanotube (TN) arrays were fabricated by an anodic oxidation process. Through a heat treatment of the as-fabricated TN arrays under a continuous Ar and acetylene flux, carbon-modified TN (C-TN) arrays were obtained. The as-fabricated catalysts were characterized by FE-SEM, HRTEM, XPS, Raman and UV-Vis spectra. Moreover, photocatalytic activity of the C-TN arrays was evaluated through the photodegradation of aqueous methyl blue. The experiments demonstrated that the C-TN arrays display an excellent photocatalytic activity. Under sunlight irradiation, the C-TN arrays are able to almost completely decompose the methylene blue pollutant of 1 × 10^− 5 M within 300 min.     

Combined electrocoagulation and TiO(2) photoassisted treatment applied to wastewater effluents from pharmaceutical and cosmetic industries

The treated wastewater consists of refractory materials and high organic content of hydrolyzed peptone residues from pharmaceutical factory. The combination of electrocoagulation (EC) followed by heterogeneous photocatalysis (TiO(2)) conditions was maximized. The EC: iron cathode/anode (12.50 cmx2.50 cmx0.10 cm), current density 763Am(-2), 90min and initial pH 6.0. As EC consequence, the majority of the dissolved organic and suspended material was removed (about 91% and 86% of the turbidity and chemical oxygen demand (COD), respectively). After EC, refractory residues still remained in the effluent. The subsequent photocatalysis: UV/TiO(2)/H(2)O(2) (mercury lamps), pH 3.0, 4h irradiation, 0.25gL(-1) TiO(2) and 10mmolL(-1) H(2)O(2) shows high levels of inorganic and organic compounds eliminations. The obtained COD values: 1753mgL(-1) for the sample from the factory, 160mgL(-1) after EC and 50mgL(-1) after EC/photocatalyzed effluents pointed out that the combined treatment stresses this water purification.     

Mesoporous TiO2 thin films embedded with Au nanoparticles for the enhancement of the photocatalytic properties

Mesoporous TiO₂ thin films were prepared by hydrothermal-oxidation of titanium metal thin films, which were obtained by DC magnetron sputtering technique. Gold nanoparticles, which were prepared by reduction of HAuCl₄, were embedded into the holes of the mesoporous TiO₂ films by capillary method followed by annealing in air up to 400 °C. The size of pore of TiO₂ films is about 100 nm and that of Au nanoparticles is about 10 nm in average. The morphology of the films was analyzed by field emission scanning electron microscope (FE-SEM) and scanning probe microscopes (SPMs). Subsequently, the photocatalytic performances of the obtained nanosystems in the decomposition of methylene blue solution are discussed. The obtained results show that the dispersion of Au nanoparticles on the mesoporous TiO2 matrix will help enhancing the photocatalytic activity with respect to pure TiO₂ under visible light irradiation.     

Facile synthesis of α-Fe2O3 nanodisk with superior photocatalytic performance and mechanism insight

Abstract

Intrinsic short hole diffusion length is a well-known problem for α-Fe₂O₃ as a visible-light photocatalytic material. In this paper, a nanodisk morphology was designed to remarkably enhance separation of electron-hole pairs of α-Fe₂O₃. As expected, α-Fe₂O₃ nanodisks presented superior photocatalytic activity toward methylene blue degradation: more than 90% of the dye could be photodegraded within 30 min in comparison with a degradation efficiency of 50% for conventional Fe₂O₃ powder. The unique multilayer structure is thought to play a key role in the remarkably improved photocatalytic performance. Further experiments involving mechanism investigations revealed that instead of high surface area, ·OH plays a crucial role in methylene blue degradation and that O^·2? may also contribute effectively to the degradation process. This paper demonstrates a facile and energy-saving route to fabricating homogenous α-Fe₂O₃ nanodisks with superior photocatalytic activity that is suitable for the treatment of contaminated water and that meets the requirement of mass production.     

TiO2/膨胀石墨复合材料的制备及其对亚甲基兰的光催化降解

采用快速升温法制备出以膨胀石墨为载体的TiO2/膨胀石墨光催化剂,用SEM及XRD对其表面形貌及结构进行表征,研究了该负载型光催化剂在紫外光照射下的催化能力,探讨了在催化剂中TiO2的负载量、亚甲基兰溶液的初始浓度及其pH值对光催化剂的降解能力的影响.结果发现,负载量为10%的光催化剂对40mg/L的亚甲基兰溶液5h的光降解率达到58.8%.     

Preparation of nitrogen co-doped SiO2/TiO2 thin films on ceramic with enhanced photocatalytic activity under visible-light irradiation

In this study, we have successfully deposited N-doped SiO₂/TiO₂ thin films on ceramic tile substrates by sol–gel method for auto cleaning purpose. After dip coating and annealing process the film was transparent, smooth and had a strong adhesion on the ceramic tile surface. The synthesised catalysts were then characterised by using several analytical techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscope (AFM) and UV-vis absorption spectroscopy (UV-vis). The analytical results revealed that the optical response of the synthesised N-doped SiO₂/TiO₂ thin films was shifted from the ultraviolet to the visible light region. The nitrogen substituted some of the lattice oxygen atoms. The surface area of co-doped catalyst increased, and its photocatalytic efficiency was enhanced. The photocatalytic tests indicated that nitrogen co-doped SiO₂/TiO₂ thin films demonstrated higher than of the SiO₂/TiO₂ activity in decolouring of methylene blue under visible light. The enhanced photocatalytic activity was attributed to an increasing of the surface area and a forming of more hydroxyl groups in the doped catalyst.     

Photocatalytic reduction of NO with NH3 using Si-doped TiO2 prepared by hydrothermal method

A series of Si-doped TiO2 (Si/TiO2) photocatalysts supported on woven glass fabric were prepared by hydrothermal method for photocatalytic reduction of NO with NH3. The photocatalytic activity tests were carried out in a continuous Pyrex reactor with the flow rate of 2000mL/min under UV irradiation (luminous flux: 1.1x10(4)lm, irradiated catalyst area: 160cm2). The photocatalysts were characterized by X-ray diffraction (XRD), BET, X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FT-IR) spectrophotometer, transmission electron microscopy (TEM), photoluminescence (PL) and temperature-programmed desorption (TPD). The experiment results showed that NO conversion on Si/TiO2 at 323K could exceed 60%, which was about 50% higher than that on Degussa P25 and pure TiO2. With the doping of Si, photocatalysts with smaller crystal size, larger surface area and larger pore volume were obtained. It was also found that Ti-O-Si bands were formed on the surface of Si/TiO2 and that the surface hydroxyl concentration was greatly increased. As a result, total acidity and NH3 chemisorption amount were enhanced for Si/TiO2 leading to its photocatalytic activity improvement.     

Degradation of bisphenol A in aqueous solution by H2O2-assisted photoelectrocatalytic oxidation

A series of titanium dioxide (TiO(2)/Ti) film electrodes were prepared from titanium (Ti) metal mesh by an improved anodic oxidation process and were further modified by photochemically depositing gold (Au) on the TiO(2) film surface as Au-TiO(2)/Ti film electrodes. The morphological characteristics, crystal structure and photoelectroreactivity of both the TiO(2)/Ti and Au-TiO(2)/Ti electrodes were studied. The experiments confirmed that the gold modification of TiO(2) film could enhance the efficiency of e(-)/h(+) separation on the TiO(2) conduction band and resulted in the higher photocatalytic (PC) and photoelectrocatalytic (PEC) activity under UV or visible illumination. To further enhance the TiO(2) PEC reaction, a reticulated vitreous carbon (RVC) electrode was applied in the same reaction system as the cathode to electrically generate H(2)O(2) in the aqueous solution. The experiments demonstrated that such a H(2)O(2)-assisted TiO(2) PEC reaction system could achieve a much better performance of BPA degradation in aqueous solution due to an interactive effect among TiO(2), Au, and H(2)O(2). It may have good potential for application in water and wastewater treatment in the future.     

Effectiveness of UV-based advanced oxidation processes for the remediation of hydrocarbon pollution in the groundwater: a laboratory investigation

The effectiveness of advanced oxidation processes in a batch and a flow reactor was investigated for the remediation of hydrocarbon pollution in the groundwater underlying a petrochemical industrial site. The main organic contaminants present in the groundwater were MTBE, benzene, alkyl-benzenes and alkyl-naphthalenes. Experimental results with a batch reactor showed that for all the organic contaminants the removal efficiency order is UV/TiO2 approximately UV/H2O2>UV (medium-pressure) in a synthetic aqueous solution, compared to UV/H2O2>UV (medium-pressure)>UV/TiO2 for the real polluted groundwater. The much lower performance of UV/TiO2 with respect to UV/H2O2 was inferred to the matrix of the groundwater, i.e. the salt content, as well as the organic and particulate matter. In fact, it is likely that the salts and dissolved organic matter quench the superoxide anion O2(-) and hydroxyl radicals just formed at the surface of the TiO2 catalyst. MTBE was the hardest compound to remove with each of the investigated treatments. UV and UV/TiO2 treatments were not able to reach a residual concentration of 10 microg/L (set by Italian legislation) even after 180 min. As for the UV/H2O2 process, only the MTBE degradation rate resulted affected by the initial H2O2 concentration, while for other compounds a complete removal was obtained within 20 min even with the lowest H2O2 concentration used (0.13 g/L). Only after 120 min of treatment, with an initial H2O2 concentration of 0.13 g/L, did the residual MTBE concentration fall below the above reported maximum admissible concentration. Instead, by using an initial concentration of 2g/L a residual concentration lower than 5 microg/L was obtained after just 30 min of reaction. The UV/H2O2 process was also investigated with a flow reactor. Results showed that it was more efficient than the batch reactor for removing MTBE, in terms of reaction time and initial H2O2 concentration required. This is consistent with the higher power of the UV lamp and with the different geometry of the flow reactor, which has a much shorter optical path than the batch reactor. By-product characterisation was also performed showing that t-butyl-formate and low molecular weight organic acids are formed as intermediate and final by-products, respectively. Finally, a preliminary evaluation of the operational cost of the UV/H2O2 process showed a value of 1.7 euro/m3 under the optimised condition.     

TiO2／膨胀石墨复合材料的制备及光催化性能的研穷

采用快速升温法制备出以膨胀石墨为载体的TiO2／膨胀石墨光催化剂，用SEM及XRD对其表面形貌及结构进行表征，研究了光催化剂在紫外光照射下的催化能力，探讨了目标降解物溶液的初始浓度及其pH值对光催化剂的降解能力的影响。结果发现，负载量为10％的光催化剂对40mg／L的亚甲基兰溶液5h的光降解率达到58．83％，甲基橙为51．12％。     

Photocatalytic degradation of Congo Red by hydrothermally synthesized nanocrystalline TiO2 and identification of degradation products by LC-MS

Degradation of Congo Red (CR) dye in aqueous solutions was investigated by means of photocatalysis of TiO2 which was hydrothermally synthesized at 200 degrees C in 2 h, in anatase phase with 8 nm crystallite size. Efficiency of TiO2 in photocatalytic degradation under visible irradiation was studied by investigating the effects of amount of TiO2, irradiation time, initial CR concentration and pH. It was found that complete decolorization is achieved within 30 min of irradiation. Effects of nitrate and sulphate ions and humic acid on the degradation were also tested. The results were compared with Degussa P-25 TiO2 at the same degradation conditions. Degradation products were detected using LC-MS technique. The probable pathways for the formation of degradation products were proposed.     

A parametric study of visible-light sensitive TiO2 photocatalysts synthesis via a facile sol–gel N-doping method

In the present work, a parametric study of visible-light sensitive TiO₂ via a facile sol–gel N-doping method was carried out. Visible-light activity of as-prepared products was assessed using solutions of methylene blue as model pollutants. Optimal visible-light activity was achieved at equal N-to-Ti precursor molar ratio and 350 °C calcinations. Characterisation of structural, chemical and optical properties of synthesised TiO₂ photocatalysts was also undertaken to elucidate the effects of N-to-Ti precursor molar ratio and calcinations temperature on the resulting photocatalytic activity. The pH value of N-doped TiO₂ sol during the preparation was also found to be an effective indicator of N-doping quality without using any post-synthesis analysis. These findings could be utilised in the successful development of TiO₂ photocatalysts or their nanocomposites for cost effective solar irradiation-driven environmental technology.