In组分渐变提高InGaN/GaN多量子阱发光二极管发光性能

利用金属有机物化学气相沉积系统在蓝宝石衬底上通过有源层的变温生长,得到In组分渐变的量子阱结构,从而获得具有三角形能带结构的InGaN/GaN多量子阱发光二极管(LED)(简称三角形量子阱结构LED).变温光致发光谱结果表明,相对于传统具有方形能带结构的量子阱LED(简称方形量子阱结构LED),三角形量子阱结构有效提高了量子阱中电子和空穴波函数的空间交叠,从而增加了LED的内量子效率;电致发光谱结果表明,三角形量子阱结构LED器件与传统结构LED器件相比,明显改善了发光峰值波长随着电流的蓝移现象.通过以上     

高效InGaN/AlInGaN发光二极管的结构设计及其理论研究（英文）

利用Advanced Physical Models of Semiconductor Devices(APSYS)理论对比研究了InGaN/AlInGaN和InGaN/GaN多量子阱作为有源层的InGaN基发光二极管的结构和电学特性。与InGaN/GaN基LED中GaN作为垒层材料相比,在AlInGaN材料体系中,通过调节AlInGaN中Al和In的组分可以优化器件的性能。当InGaN阱层材料中In组分为8%时,可以实现无应力的In0.08Ga0.92N/AlInGaN基LED。在这种无应力结构中可以进一步降低大功率LED的"效率下降"(Effciency droop)问题。理论模拟结果显示,四元系AlInGaN作为垒层可以进一步减少载流子泄露,增加空穴注入效率,减少极化场对器件性能的影响。在In0.08Ga0.92N/AlInGaN量子阱中的载流子浓度、有源层的辐射复合率、电流特性曲线和内量子效率等方面都优于InGaN/GaN基LED。无应变AlInGaN垒层代替传统的GaN垒层后,能够得到高效的发光二极管,并且大电流注入下的"效率滚降"问题得到改善。     

p型GaN/Al0.35Ga0.65N/GaN应变量子阱中二维空穴气的研究

对Ga面p型GaN/Al0.35Ga0.65N/GaN应变异质结构中形成的二维空穴气(2DHG)进行了研究.首先基于半导体-绝缘体-半导体异质结构模型确定了应变异质中的临界厚度,然后自洽求解薛定谔方程和泊松方程,计算了当中间势垒层AlGaN处于完全应变状态和半应变状态两种条件下,顶层GaN及中间层AlGaN厚度的变化对2DHG分布的影响.计算结果表明,势垒层AlGaN和顶层GaN的应变状态和厚度对极化引起的2DHG面密度及分布有重要影响.在此基础上制备了p型GaN/Al0.35 Ga0.65N/GaN应变量子阱结构肖特基器件,并通过器件的C-V测试证实了异质结处2DHG的存在.器件响应光谱的测试结果表明,由于p型GaN/Al0.35Ga0.65N/GaN量子阱中强烈的极化作用和Stark效应使得器件零偏压和反向偏压时的响应光谱都向短波方向移动了10 nm,在零偏压下器件在280 nm处的峰值响应为0.022 A/W,在反向偏压为1 V时,峰值响应达到0.19 A/W,已经接近理论值.     

以弱p型为有源区的新型p-n结构GaN紫外探测器

提出了以弱p型（p^－-GaN）为有源区的p-n结构GaN紫外探测器.由于弱p型层的载流子浓度较低,很容易增加耗尽区的宽度,从而可以增加器件的量子效率.通过模拟计算,研究了金属与p^－-GaN层的肖特基接触势垒高度、p^－-GaN层厚度等参数对器件性能的影响.研究结果表明,降低金属与p^－-GaN层的接触势垒高度、适当减小p^－-GaN层厚度能够实现有源层方向单一的内建电场,从而提高器件的量子效率.要制备出 关键词： 弱p型GaN 紫外探测器 量子效率     

蓝光激光器结构中InGaN/GaN多量子阱界面效应的精细光致发光光谱研究

金属有机化学气相沉积(MOCVD)方法制备InGaN/GaN多量子阱结构时,在GaN势垒层生长的N2载气中引入适量H2,能够有效改善阱/垒界面质量从而提升发光效率.本工作利用光致发光(PL)光谱技术,对蓝光激光器结构中的InGaN/GaN多量子阱的发光性能进行了精细的光谱学测量与表征,研究了通H2生长对量子阱界面的调控...     

全息技术制作二维光子晶体蓝宝石衬底提高发光二极管外量子效率

为了提高GaN基发光二极管(LED)的外量子效率,在蓝宝石衬底制作了二维光子晶体.衬底上的二维光子晶体结构采用激光全息技术和感应耦合等离子体(ICP)干法刻蚀技术制作,然后采用金属氧化物化学气相沉积(MOCVD)技术在图形蓝宝石衬底(PSS)上生长2μm厚的n型GaN层,4层量子阱和200nm厚的p型GaN层,形成LED结构.衬底上制作的二维光子晶体为六角晶格结构,晶格常数为3.8μm,刻蚀深度为800nm.LED器件光强输出测试结果显示,在PSS上制作的LED(PSS-LED)的发光强度普遍高于蓝宝石平 关键词： 全息 发光二极管 图形蓝宝石衬底 外量子效率     

垒掺In提高InGaN/GaN多量子阱发光特性

利用金属有机物化学气相淀积技术在蓝宝石衬底上生长InGaN/GaN多量子阱结构.对多量子阱垒层掺In和非掺In进行了比较研究，结果表明，垒掺In 的样品界面质量变差，但明显增加了光致发光谱的峰值强度和积分强度，带边峰与黄光峰强度之比增大，降低了表面粗糙度.利用这两种结构制备了相应的发光二极管(LED)样品.通过电荧光测量可知，垒掺In的LED比非掺In的LED有较高的发光强度和相对均匀的波长，这主要是由于垒掺In后降低了阱与垒之间晶格失配的应力，从而降低了极化电场，提高了辐射复合效率. 关键词： InGaN/GaN多量子阱 X射线双晶衍射 原子力显微镜 光致发光     

高效InGaN/AlInGaN发光二极管的结构设计及其理论研究

利用Advanced Physical Models of Semiconductor Devices (APSYS)理论对比研究了InGaN/AlInGaN 和 InGaN/GaN多量子阱作为有源层的InGaN基发光二极管的结构和电学特性。与InGaN/GaN 基LED 中GaN作为垒层材料相比,在AlInGaN材料体系中,通过调节AlInGaN中Al和In的组分可以优化器件的性能。当InGaN阱层材料中In组分为8%时,可以实现无应力的In_0.08Ga_0.92N/AlInGaN基 LED。在这种无应力结构中可以进一步降低大功率LED的"效率下降"(Effciency droop)问题。理论模拟结果显示,四元系AlInGaN作为垒层可以进一步减少载流子泄露,增加空穴注入效率,减少极化场对器件性能的影响。在In_0.08Ga_0.92N /AlInGaN量子阱中的载流子浓度、有源层的辐射复合率、电流特性曲线和内量子效率等方面都优于InGaN/GaN基LED。无应变AlInGaN垒层代替传统的GaN垒层后,能够得到高效的发光二极管,并且大电流注入下的"效率滚降"问题得到改善。     

近紫外380nm发光二极管的量子阱结构优化

模拟分析了有源区不同垒层对380 nm近紫外发光二极管的内量子效率、电子空穴浓度分布、辐射复合效率等产生的影响。有源区垒层材料分别选用GaN、Al0.1Ga0.9N、Al0.1Ga0.9N/Al0.15Ga0.85N/Al0.1Ga0.9N,其中3层AlGaN的厚度比分别为6 nm/8 nm/6 nm和7 nm/6 nm/7 nm。对比分析发现,与GaN垒层相比,选用AlGaN系列垒层可以将更多的载流子限制在有源区内,空穴浓度可以提高近一个数量级,辐射复合效率可以提高2～10倍;3层AlGaN垒层相对于单一AlGaN垒层,载流子分布更加均匀,辐射复合效率可以提高7倍以上,内量子效率可以提高14.5%;采用不同厚度比的3层AlGaN垒层结构可以微调能带的倾斜程度,进一步减小极化效应。可以调节合适的厚度比减小极化效应对于载流子分布及内量子效率的影响。     

量子阱结构对有机电致发光器件效率的影响

实验中共制备了五种有机量子阱结构电致发光器件,分别对这五种量子阱结构器件的电致发光特性进行了研究,分析了量子阱结构的周期数和势垒层的厚度对器件电学性能的影响.实验结果表明适当周期数的量子阱结构器件的亮度和电流效率比传统的三层结构器件的要大,主要原因是量子阱结构对电子和空穴的限制作用,这种限制作用提高了电子和空穴在发光层中形成激子和复合的概率,从而提高了发光的亮度和效率.当改变阱结构器件中势阱层的厚度时,也会对器件的亮度和效率产生影响,采用适当的势阱层厚度能够提高器件的亮度和效率. 关键词： 量子阱结构 电致发光 电流效率 光谱     

阶梯AlGaN外延新型Al0.25Ga0.75N/GaNHEMTs器件实验研究

本文报道了作者提出的阶梯AlGaN外延层新型AlGaN/GaN HEMTs结构的实验结果. 实验利用感应耦合等离子体刻蚀(ICP)刻蚀栅边缘的AlGaN外延层, 形成阶梯的AlGaN 外延层结构, 获得浓度分区的沟道2DEG, 使得阶梯AlGaN外延层边缘出现新的电场峰, 有效降低栅边缘的高峰电场, 从而优化了AlGaN/GaN HEMTs器件的表面电场分布. 实验获得了阈值电压-1.5 V的新型AlGaN/GaN HEMTs器件. 经过测试, 同样面积的器件击穿电压从传统结构的67 V提高到新结构的106 V, 提高了58%左右; 脉冲测试下电流崩塌量也比传统结构减少了30%左右, 电流崩塌效应得到了一定的缓解.     

Enhanced carrier injection in InGaN/GaN multiple quantum wells LED with polarization-induced electron blocking barrier

In this report, we designed a light emitting diode (LED) structure in which an N-polar p-GaN layer is grown on top of Ga-polar In_0.1Ga_0.9N/GaN quantum wells (QWs) on an n-GaN layer. Numerical simulation reveals that the large polarization field at the polarity inversion interface induces a potential barrier in the conduction band, which can block electron overflow out of the QWs. Compared with a conventional LED structure with an Al_0.2Ga_0.8N electron blocking layer (EBL), the proposed LED structure shows much lower electron current leakage, higher hole injection, and a significant improvement in the internal quantum efficiency (IQE). These results suggest that the polarization induced barrier (PIB) is more effective than the AlGaN EBL in suppressing electron overflow and improving hole transport in GaN-based LEDs.     

Output light power of InGaN-based violet laser diodes improved by using a u-InGaN/GaN/AlGaN multiple upper waveguide

The upper waveguide(UWG) has direct influences on the optical and electrical characteristics of the violet laser diode(LD) by changing the optical field distribution or barrier of the electron blocking layer(EBL). In this study, a series of In GaN-based violet LDs with different UWGs are investigated systematically with LASTIP software. It is found that the output light power(OLP) under an injecting current of 120 mA or the threshold current(Ith) is deteriorated when the UWG is u-In_(0.02)Ga_(0.98)N/GaN or u-In_(0.02)Ga_(0.98)N/Al_xGa_(1-x)N(0 ≤ x ≤ 0.1), which should be attributed to small optical confinement factor(OCF) or severe electron leakage. Therefore, a new violet LD structure with u-In_(0.02)Ga_(0.98)N/GaN/Al_(0.05)Ga_(0.95)N multiple layer UWG is proposed to reduce the optical loss and increase the barrier of EBL. Finally,the output light power under an injecting current of 120 mA is improved to 176.4 mW.     

Electron mobility limited by surface and interface roughness scattering in AlxGa1-xN/GaN quantum wells

The electron mobility limited by the interface and surface roughness scatterings of the two-dimensional electron gas in AlxGa1-xN/GaN quantum wells is studied. The newly proposed surface roughness scattering in the AlGaN/GaN quantum wells becomes effective when an electric field exists in the AlxGa1-xN barrier. For the AlGaN/GaN potential well, the ground subband energy is governed by the spontaneous and the piezoelectric polarization fields which are determined by the barrier and the well thicknesses. The thickness fluctuation of the AlGaN barrier and the GaN well due to the roughnesses cause the local fluctuation of the ground subband energy, which will reduce the 2DEG mobility.     

AlN插入层对AlxGa1-xN/GaN界面电子散射的影响

本文研究AlN作为Al_xGa_1-xN/GaN插入层引起的电子输运性质的变化, 考虑了Al_xGa_1-xN和AlN势垒层的自发极化、压电极化对Al_xGa_1-xN/AlN/GaN双异质结高电子迁移率晶体管(HEMT)中极化电荷面密度、二维电子气(2DEG) 浓度的影响, 分析了AlN厚度与界面粗糙度散射和合金无序散射的关系; 结果表明, 2DEG 浓度、界面粗糙度散射和合金无序散射依赖于AlN层厚度, 插入一层1–3 nm薄的AlN层, 可以明显提高电子迁移率.     

Dual-blue light-emitting diode based on strain-compensated InGaN-AlGaN/GaN quantum wells

Strain-compensated InGaN quantum well (QW) active region employing tensile AlGaN barrier is analyzed. Its spectral stability and efficiency droop for dual-blue light-emitting diode (LED) are improved compared with those of the conventional InGaN/GaN QW dual-blue LED based on stacking structure of two In_0.18Ga_0.82N/GaN QWs and two In_0.12Ga_0.88N/GaN QWs on the same sapphire substrate. It is found that the optimal performance is achieved when the Al composition of strain-compensated AlGaN layer is 0.12 in blue QW and 0.21 in blue-violet QW. The improvement performance can be attributed to the strain-compensated InGaN-AlGaN/GaN QW that can provide a better carrier confinement and effectively reduce leakage current.     

A dual-blue light-emitting diode based on strain-compensated InGaN-AlGaN/GaN quantum wells

A strain-compensated InGaN quantum well(QW) active region employing a tensile AlGaN barrier is analyzed.Its spectral stability and efficiency droop for a dual-blue light-emitting diode(LED) are improved compared with those of the conventional InGaN/GaN QW dual-blue LEDs based on a stacking structure of two In0.18Ga0.82N/GaN QWs and two In0.12Ga0.88N/GaN QWs on the same sapphire substrate.It is found that the optimal performance is achieved when the Al composition of the strain-compensated AlGaN layer is 0.12 in blue QW and 0.21 in blue-violet QW.The improvement performance can be attributed to the strain-compensated InGaN-AlGaN/GaN QW,which can provide a better carrier confinement and effectively reduce leakage current.     

Abnormal phenomenon of source-drain current of AlGaN/GaN heterostructure device under UV/visible light irradiation

We report an abnormal phenomenon that the source-drain current (I_D) of AlGaN/GaN heterostructure devices decreases under visible light irradiation. When the incident light wavelength is 390 nm, the photon energy is less than the band gaps of GaN and AlGaN whereas it can causes an increase of I_D. Based on the UV light irradiation, a decrease of I_D can still be observed when turning on the visible light. We speculate that this abnormal phenomenon is related to the surface barrier height, the unionized donor-like surface states below the surface Fermi level and the ionized donor-like surface states above the surface Fermi level. For visible light, its photon energy is less than the surface barrier height of the AlGaN layer. The electrons bound in the donor-like surface states below the Fermi level are excited and trapped by the ionized donor-like surface states between the Fermi level and the conduction band of AlGaN. The electrons trapped in ionized donor-like surface states show a long relaxation time, and the newly ionized donor-like surface states below the surface Fermi level are filled with electrons from the two-dimensional electron gas (2DEG) channel at AlGaN/GaN interface, which causes the decrease of I_D. For the UV light, when its photon energy is larger than the surface barrier height of the AlGaN layer, electrons in the donor-like surface states below the Fermi level are excited to the conduction band and then drift into the 2DEG channel quickly, which cause the increase of I_D.     

GaN/AlGaN双带红外探测及光子频率上转换研究

研究了GaN/AlGaN异质结构中的双带（中、远）红外探测及光子频率上转换特性.通过光致发光光谱确认GaN/AlGaN探测器结构中AlGaN本征层的Al组分,讨论了不同Al组分GaN/AlGaN异质结的导带带阶界面功函数差.在拟合单周期GaN/AlGaN探测器中红外和远红外波段响应谱的基础上,研究多周期GaN/AlGaN探测器与GaN/AlGaN发光二极管集成结构的中红外和远红外光子频率上转换效率与GaN发射层厚度、AlGaN本征层厚度、紫光光子出射效率、内量子效率、空间频率和发射层掺杂浓度间的关系,优化 关键词： 双带红外探测 光子频率上转换 响应谱 GaN/AlGaN     

Piezoelectric polarization and quantum size effects on the vertical transport in AlGaN/GaN resonant tunneling diodes

In this work,the electronic properties of resonant tunneling diodes(RTDs) based on GaN-AlxGa(1-x)N double barriers are investigated by using the non-equilibrium Green functions formalism(NEG).These materials each present a wide conduction band discontinuity and a strong internal piezoelectric field,which greatly affect the electronic transport properties.The electronic density,the transmission coefficient,and the current–voltage characteristics are computed with considering the spontaneous and piezoelectric polarizations.The influence of the quantum size on the transmission coefficient is analyzed by varying GaN quantum well thickness,Al_xGa_(1-x)N width,and the aluminum concentration x_(Al).The results show that the transmission coefficient more strongly depends on the thickness of the quantum well than the barrier;it exhibits a series of resonant peaks and valleys as the quantum well width increases.In addition,it is found that the negative differential resistance(NDR) in the current–voltage(I–V) characteristic strongly depends on aluminum concentration xAl.It is shown that the peak-to-valley ratio(PVR) increases with xAlvalue decreasing.These findings open the door for developing vertical transport nitrides-based ISB devices such as THz lasers and detectors.