增强型AlGaN/GaN高电子迁移率晶体管高温退火研究

深入研究了两种增强型AlGaN/GaN高电子迁移率晶体管(HEMT)高温退火前后的直流特性变化.槽栅增强型AlGaN/GaN HEMT在500 ℃ N₂中退火5 min后,阈值电压由0.12 V正向移动到0.57 V,器件Schottky反向栅漏电流减小一个数量级.F注入增强型AlGaN/GaN HEMT在 400 ℃ N₂中退火2 min后,器件阈值电压由0.23 V负向移动到-0.69 V,栅泄漏电流明显增大.槽栅增强型器件退火过程中Schottky有效势垒     

60Co γ射线辐射对AlGaN/GaN HEMT器件的影响

采用⁶⁰Co γ射线辐射源对非钝化保护的AlGaN/GaN高电子迁移率晶体管(HEMT)器件进行了1 Mrad(Si)的总剂量辐射,实验发现辐射累积剂量越大,器件尺寸越小,器件饱和漏电流和跨导下降越明显,同时辐射后器件栅泄漏电流明显增大,而阈值电压变化很小. 对辐射前后器件的沟道串联电阻和阈值电压变化的分析表明,辐射感生表面态负电荷的产生是造成AlGaN/GaN HEMT器件电特性退化的主要原因之一. 关键词： AlGaN/GaN HEMT器件 γ射线辐射 表面态     

AlGaN/GaN槽栅HEMT模拟与实验研究

分析了栅槽深度对AlGaN/GaN HEMT特性的影响,并对不同栅槽深度的器件特性进行了模拟,得到了器件饱和电流、最大跨导和阈值电压随栅槽深度的变化规律.当槽栅深度增大,器件饱和电流逐渐下降,而最大跨导逐渐增大,阈值电压向X轴正方向移动.研制出不同栅槽深度的蓝宝石衬底AlGaN/GaN HEMT,用实验数据验证了得到的不同栅槽深度器件特性变化规律.从刻蚀损伤和刻蚀引入界面态的角度分析了模拟与实验规律产生差别的原因. 关键词： 高电子迁移率晶体管 AlGaN/GaN 槽栅器件     

60Co γ射线辐射对AlGaN/GaN HEMT器件的影响

采用60 Co γ射线辐射源对非钝化保护的AlGaN/GaN高电子迁移率晶体管(HEMT)器件进行了1 Mrad(Si)的总剂量辐射,实验发现辐射累积剂量越大,器件尺寸越小,器件饱和漏电流和跨导下降越明显,同时辐射后器件栅泄漏电流明显增大,而阈值电压变化很小. 对辐射前后器件的沟道串联电阻和阈值电压变化的分析表明,辐射感生表面态负电荷的产生是造成AlGaN/GaN HEMT器件电特性退化的主要原因之一.     

新型双异质结高电子迁移率晶体管的电流崩塌效应研究

针对传统单结GaN基高电子迁移率晶体管器件性能受电流崩塌效应和自加热效应限制的困境,对新型A1GaN/GaN/InGaN/GaN双异质结高电子迁移率晶体管的直流性质展开了系统研究.采用基于热电子效应和自加热效应的流体动力模型,研究了器件在不同偏压下电流崩塌和负微分电导效应与GaN沟道层厚度的相关.研究发现具有高势垒双异质的沟道层能更好地将电子限制在沟道中,显著减小高电场下热电子从沟道层向GaN缓冲层的穿透能力.提高GaN沟道层厚度可以有效抑制电流崩塌和和负微分输出电导,进而提高器件在高场作用下的性能.所得结果为进一步优化双异质结高电子迁移率晶体管结构提供了新思路,可促进新型GaN高电子迁移率晶体管器件在高功率、高频和高温等无线通讯领域内的广泛应用.     

氮化镓基感光栅极高电子迁移率晶体管器件设计与制备

GaN基高电子迁移率晶体管(HEMT)作为栅控器件,具有AlGaN/GaN异质结处高浓度的二维电子气(2DEG)及对表面态敏感等特性,在栅位置处与感光功能薄膜的结合是光探测器领域重要的研究方向之一.本文首先提出在GaN基HEMT栅电极上引入光敏材料锆钛酸铅(PZT),将具有光伏效应的铁电薄膜PZT与HEMT栅极结合,提出一种新的"金属/铁电薄膜/金属/半导体(M/F/M/S)"结构;然后在以蓝宝石为衬底的AlGaN/GaN外延片上制备感光栅极HEMT器件.最后,通过PZT的光伏效应来调控沟道中的载流子浓度和通过源漏电流的变化来实现对可见光和紫外光的探测.在365 nm紫外光和普通可见光条件下,对比测试有/无感光栅极的HEMT器件,在较小V_(gs)电压时,可见光下测得前者较后者的饱和漏源电流I_(ds)的增幅不下降,紫外光下前者较后者的I_(ds)增幅大5.2 mA,由此可知,感光栅PZT在可见光及紫外光下可作用于栅极GaN基HEMT器件并可调控沟道电流.     

基于GaN同质衬底的高迁移率AlGaN/GaNHEMT材料

研究了表面预处理对GaN同质外延的影响,获得了高电子迁移率AlGaN/GaN异质结材料.通过NH_3/H_2混合气体与H_2交替通入反应室的方法对GaN模板和GaN半绝缘衬底进行高温预处理.研究结果表明,NH_3/H_2能够抑制GaN的分解,避免粗糙表面,但不利于去除表面的杂质,黄光带峰相对强度较高;H_2促进GaN分解,随时间延长GaN分解加剧,导致模板表面粗糙不平,AlGaN/GaN HEMT材料二维电子气迁移率降低.采用NH_3/H_2混合气体与H_2交替气氛模式处理模板或衬底表面,能够清洁表面,去除表面杂质,获得平滑的生长表面和外延材料表面,有利于提高AlGaN/GaN HEMT材料电学性能.在GaN衬底上外延AlGaN/GaN HEMT材料,2DEG迁移率达到2113 cm~2/V·s,电学性能良好.     

AlGaN/GaN肖特基结参数分析与电流运输机理研究

通过对AlGaN/GaN HEMT器件肖特基栅电流输运机理的研究,在变温下采用I-V法对AlGaN/GaN上的Ni/Au肖特基势垒高度和理想因子进行了计算. 通过对不同电流机理的分立研究,得到了更为准确的势垒高度值_b. 通过分析温度在300—550K之间肖特基反向泄漏电流的特性,得出结论：AlGaN材料的表面漏电不是HEMT器件反向泄漏电流的主要来源. 关键词： AlGaN/GaN异质结 肖特基结 理想因子     

背势垒层结构对AlGaN/GaN双异质结载流子分布特性的影响

首先通过一维自洽求解薛定谔/泊松方程,研究了AlGaN/GaN双异质结构中AlGaN背势垒层Al组分和厚度对载流子分布特性的影响.其次利用低压MOCVD方法在蓝宝石衬底上生长出具有不同背势垒层的AlGaN/GaN双异质结构材料,通过汞探针CV测试验证了理论计算的正确性.理论计算和实验结果均表明,随着背势垒层Al组分的提高和厚度的增加,主沟道中的二维电子气面密度逐渐减小,寄生沟道的二维电子气密度逐渐增加;背势垒层Al组分的提高和厚度的增加能有效的增强主沟道的二维电子气限域性,但是却带来了较高的 关键词： AlGaN/GaN 双异质结构 限域性 寄生沟道     

Al2O3绝缘层的AlGaN/GaN MOSHEMT器件研究

在研制AlGaN/GaN HEMT器件的基础上,采用ALD法制备了Al₂O₃ AlGaN/GaN MOSHEMT器件.通过X射线光电子能谱测试表明在AlGaN/GaN异质结材料上成功淀积了Al₂O₃薄膜.根据对HEMT和MOSHEMT器件肖特基电容、器件输出以及转移特性的测试进行分析发现：所制备的Al₂O₃薄膜与AlGaN外延层间界面态密度较小,因而MOSHEMT器件呈现出较 关键词： 2O₃')" href="#">Al₂O₃ ALD GaN MOSHEMT     

N极性GaN/AlGaN异质结二维电子气模拟

通过自洽求解薛定谔方程和泊松方程,较系统地研究了GaN沟道层、AlGaN背势垒层、Si掺杂和AlN插入层对N极性GaN/AlGaN异质结中二维电子气(2DEG)的影响,分析表明,GaN沟道层厚度、AlGaN背势垒层厚度及Al组分变大都能一定程度上提高二维电子气面密度,AlGaN背势垒层的厚度和Al组分变大也可提高二维电子气限阈性,且不同的Si掺杂形式对二维电子气的影响也有差异,而AlN插入层在提高器件二维电子气面密度、限阈性等方面表现都较为突出,在模拟中GaN沟道层厚度小于5nm时无法形成二维电子气,超过20nm后二维电子气面密度趋于饱和,而AlGaN背势垒厚度超过40nm后二维电子气也有饱和趋势,对均匀掺杂和delta掺杂而言AlGaN背势垒层Si掺杂浓度超过5×10~(19)cm~(-3)后2DEG面密度开始饱和,而厚度为2nmAlN插入层的引入会使2DEG面密度从无AlN插入层时的0.93×10~(13)cm~(-2)提高到1.17×10~(13)cm~(-2)。     

Non-recessed-gate quasi-E-mode double heterojunction AlGaN/GaN high electron mobility transistor with high breakdown voltage

A non-recessed-gate quasi-E-mode double heterojunction AlGaN/GaN high electron mobility transistor(quasi-EDHEMT) with a thin barrier, high breakdown voltage and good performance of drain induced barrier lowering(DIBL)was presented. Due to the metal organic chemical vapor deposition(MOCVD) grown 9-nm undoped AlGaN barrier, the effect that the gate metal depleted the two-dimensiomal electron gas(2DEG) was greatly impressed. Therefore, the density of carriers in the channel was nearly zero. Hence, the threshold voltage was above 0 V. Quasi-E-DHEMT with 4.1-μm source-to-drain distance, 2.6-μm gate-to-drain distance, and 0.5-μm gate length showed a drain current of 260 mA/mm.The threshold voltage of this device was 0.165 V when the drain voltage was 10 V and the DIBL was 5.26 mV/V. The quasi-E-DHEMT drain leakage current at a drain voltage of 146 V and a gate voltage of-6 V was below 1 mA/mm. This indicated that the hard breakdown voltage was more than 146 V.     

阶梯AlGaN外延新型Al_(0.25)Ga_(0.75)N/GaNHEMTs击穿特性分析

为了优化AlGaN/GaN HEMTs器件表面电场,提高击穿电压,本文首次提出了一种新型阶梯AlGaN/GaN HEMTs结构.新结构利用AlGaN/GaN异质结形成的2DEG浓度随外延AlGaN层厚度降低而减小的规律,通过减薄靠近栅边缘外延的AlGaN层,使沟道2DEG浓度分区,形成栅边缘低浓度2DEG区,低的2DEG使阶梯AlGaN交界出现新的电场峰,新电场峰的出现有效降低了栅边缘的高峰电场,优化了AlGaN/GaN HEMTs器件的表面电场分布,使器件击穿电压从传统结构的446 V,提高到新结构的640 V.为了获得与实际测试结果一致的击穿曲线,本文在GaN缓冲层中设定了一定浓度的受主型缺陷,通过仿真分析验证了国际上外延GaN缓冲层时掺入受主型离子的原因,并通过仿真分析获得了与实际测试结果一致的击穿曲线.     

Two-dimensional electron gas densities in AlGaN/AlN/GaN heterostructures

The dependence of two-dimensional electron gas (2DEG) density and distribution in an Al_xGa_1-xN/AlN/GaN heterostructure on the thicknesses of the Al_xGa_1-xN barrier layer and the AlN interfacial layer are investigated theoretically. A competitive contribution of the AlGaN and AlN layers to the 2DEG density is revealed. For an AlN interfacial layer thinner than a critical value d_cAlN, the 2DEG density is dominated by the AlGaN barrier and the 2DEG density increases with the increase of the AlGaN barrier thickness, as in the case of a simple AlGaN/GaN heterostructure. While the AlN interfacial layer will take the dominant contribution to the 2DEG density as its thickness exceeds d_cAlN. In this case, the increase of AlGaN barrier layer thickness leads to the decrease of the 2DEG density. Detailed calculations show that the critical AlN thickness increases with the increase of Al content in the AlGaN barrier. PACS 85.30.De; 73.40.Kp; 02.60.Cb     

Breakdown mechanisms in AlGaN/GaN high electron mobility transistors with different GaN channel thickness values

In this paper,the off-state breakdown characteristics of two different AlGaN/GaN high electron mobility transistors（HEMTs）,featuring a 50-nm and a 150-nm GaN thick channel layer,respectively,are compared.The HEMT with a thick channel exhibits a little larger pinch-off drain current but significantly enhanced off-state breakdown voltage(SV_off).Device simulation indicates that thickening the channel increases the drain-induced barrier lowering（DIBL） but reduces the lateral electric field in the channel and buffer underneath the gate.The increase of BV_off in the thick channel device is due to the reduction of the electric field.These results demonstrate that it is necessary to select an appropriate channel thickness to balance DIBL and BV_off in AlGaN/GaN HEMTs.     

Optimization of two-dimensional electron gases and – characteristics for AlGaN/GaN HEMT devices

In this paper, we take account of the spontaneous and piezoelectric polarization effect at the heterointerface in the AlGaN/GaN HEMT device, and one-dimensional Schrödinger–Poisson equations are solved self-consistently using a nonuniform mesh; using our findings, the AlGaN/GaN heterostructure conduction band and the two-dimensional electron gas (2DEG) density are investigated. The dependences of the 2DEG characteristics on the Al fraction, the thickness of each layer, the donor concentration and the gate voltage are investigated through simulation. The output characteristics are simulated using a quasi-2D model; a saturation voltage and threshold voltage are also shown. The influence of the spacer layer width on the 2DEG density is calculated for the first time. An explanation and analyses are given.     

Electron mobility in the linear region of an AlGaN/AlN/GaN heterostructure field-effect transistor

We simulate the current-voltage （I-V） characteristics of AlGaN/AlN/GaN heterostructure field-effect transistors （HFETs） with different gate lengths using the quasi-two-dimensional （quasi-2D） model. The calculation results obtained using the modified mobility model are found to accord well with the experimental data. By analyzing the variation of the electron mobility for the two-dimensional electron gas （213EG） with the electric field in the linear region of the AlGaN/AlN/GaN HFET I-V output characteristics, it is found that the polarization Coulomb field scattering still plays an important role in the electron mobility of AlGaN/AlN/GaN HFETs at the higher drain voltage and channel electric field. As drain voltage and channel electric field increase, the 2DEG density reduces and the polarization Coulomb field scattering increases, as a result, the 2DEG electron mobility decreases.     

具有部分本征GaN帽层新型AlGaN/GaN高电子迁移率晶体管特性分析

为了优化传统Al GaN/GaN高电子迁移率晶体管(high electron mobility transistors,HEMTs)器件的表面电场,提高击穿电压,本文提出了一种具有部分本征GaN帽层的新型Al GaN/GaN HEMTs器件结构.新型结构通过在Al GaN势垒层顶部、栅电极到漏电极的漂移区之间引入部分本征GaN帽层,由于本征GaN帽层和Al GaN势垒层界面处的极化效应,降低了沟道二维电子气(two dimensional electron gas,2DEG)的浓度,形成了栅边缘低浓度2DEG区域,使得沟道2DEG浓度分区,由均匀分布变为阶梯分布.通过调制沟道2DEG的浓度分布,从而调制了Al GaN/GaN HEMTs器件的表面电场.利用电场调制效应,产生了新的电场峰,且有效降低了栅边缘的高峰电场,Al GaN/GaN HEMTs器件的表面电场分布更加均匀.利用ISE-TCAD软件仿真分析得出:通过设计一定厚度和长度的本征GaN帽层,Al GaN/GaN HEMTs器件的击穿电压从传统结构的427 V提高到新型结构的960 V.由于沟道2DEG浓度减小,沟道电阻增加,使得新型Al GaN/GaN HEMTs器件的最大输出电流减小了9.2%,截止频率几乎保持不变,而最大振荡频率提高了12%.     

阶梯AlGaN外延新型Al0.25Ga0.75N/GaNHEMTs器件实验研究

本文报道了作者提出的阶梯AlGaN外延层新型AlGaN/GaN HEMTs结构的实验结果. 实验利用感应耦合等离子体刻蚀(ICP)刻蚀栅边缘的AlGaN外延层, 形成阶梯的AlGaN 外延层结构, 获得浓度分区的沟道2DEG, 使得阶梯AlGaN外延层边缘出现新的电场峰, 有效降低栅边缘的高峰电场, 从而优化了AlGaN/GaN HEMTs器件的表面电场分布. 实验获得了阈值电压-1.5 V的新型AlGaN/GaN HEMTs器件. 经过测试, 同样面积的器件击穿电压从传统结构的67 V提高到新结构的106 V, 提高了58%左右; 脉冲测试下电流崩塌量也比传统结构减少了30%左右, 电流崩塌效应得到了一定的缓解.     

Impact of AlxGa1-xN barrier thickness and Al composition on electrical properties of ferroelectric HfZrO/Al2O3/AlGaN/GaN MFSHEMTs

Ferroelectric (FE) HfZrO/Al$_{2}$O$_{3}$ gate stack AlGaN/GaN metal-FE-semiconductor heterostructure high-electron mobility transistors (MFSHEMTs) with varying Al$_{x}$Ga$_{1-x}$N barrier thickness and Al composition are investigated and compared by TCAD simulation with non-FE HfO$_{2}$/Al$_{2}$O$_{3}$ gate stack metal-insulator-semiconductor heterostructure high-electron mobility transistors (MISHEMTs). Results show that the decrease of the two-dimensional electron gas (2DEG) density with decreasing AlGaN barrier thickness is more effectively suppressed in MFSHEMTs than that in MISHEMTs due to the enhanced FE polarization switching efficiency. The electrical characteristics of MFSHEMTs, including transconductance, subthreshold swing, and on-state current, effectively improve with decreasing AlGaN thickness in MFSHEMTs. High Al composition in AlGaN barrier layers that are under 3-nm thickness plays a great role in enhancing the 2DEG density and FE polarization in MFSHEMTs, improving the transconductance and the on-state current. The subthreshold swing and threshold voltage can be reduced by decreasing the AlGaN thickness and Al composition in MFSHEMTs, affording favorable conditions for further enhancing the device.