大气压空气纳秒脉冲板-板放电中逃逸电子产生机理

经典放电理论(Townsend和流注理论)解释纳秒脉冲气体放电存在局限性,近年来基于高能电子逃逸的纳秒脉冲气体放电理论研究受到广泛关注.但是目前对大气压空气纳秒脉冲板-板放电中逃逸电子产生机理研究仍较少,严重阻碍了纳秒脉冲放电等离子体的应用发展.本文利用一维粒子模型,对幅值为20 kV的纳秒脉冲电压驱动下,间隙长为1 mm的板-板电极之间的大气压空气放电中逃逸电子的产生机理进行了数值模拟研究..结果表明,在空间电荷动力学行为的影响下,板-板电极之间出现了增强电场区域,使得电子可以满足电子逃逸判据而进入逃逸模式.此外,还观察到放电通道前逃逸电子的预电离效应导致了二次电子崩的产生,随着二次电子崩与放电通道不断汇聚,引导并加速了放电通道的发展,最终导致气隙击穿.本研究进一步揭示了纳秒脉冲板-板放电机理,拓展了纳秒脉冲气体放电基础理论,为纳秒脉冲放电等离子体的应用和发展开辟了新的机会.     

大气压尖板电极结构重复频率纳秒脉冲放电中X射线辐射特性研究

文章通过碘化钠晶体和光电倍增管构成的X射线探测系统,研究了上升沿15ns,脉宽30-40ns量级,电压90kV的大气压重频纳秒脉冲气体放电中X射线的辐射特性,X射线有效探测能量范围为10-130keV.结果表明放电产生的X射线主要集中在20-90keV能量范围,而能量在十几keV的软X射线和超过90keV的高能X射线数量很少.X射线辐射计数随脉冲重复频率的增加而增加,随着气隙距离的改变存在峰值,且峰值出现在弥散放电模式.     

120 kV下常压空气纳秒脉冲电晕放电特性

使用上升沿15 ns、脉宽30~40 ns的重复频率纳秒脉冲电源对120 kV下大气压空气中管-板电极结构电晕放电进行了实验研究,通过电压电流测量、放电图像拍摄和X射线探测分析了纳秒脉冲电晕放电特性。结果表明:纳秒脉冲电晕放电中存在X射线辐射,但辐射强度较弱,X射线辐射计数随着气隙距离的增大而减少,随着脉冲重复频率的增大而增多;放电空间的残余电荷加强了下一个脉冲到来时的局部电场,从而导致高重复频率下易于出现分散的电晕通道。     

纳秒脉冲气体放电中逃逸电子束流的研究

经典的放电理论(Townsend和流注理论)不能很好地解释纳秒脉冲放电中的现象,近年来基于高能量电子逃逸击穿的纳秒脉冲气体放电理论研究受到广泛关注,有研究发现,高能逃逸电子是纳秒脉冲气体放电中的新特征参数,本文研制了用于测量纳秒脉冲放电中逃逸电子束流的收集器,并对脉宽3—5ns、上升沿1.2—1.6 n8激励的大气压纳秒脉冲气体放电中逃逸电子束流进行了测量,收集器采用类似法拉第杯的原理,利用金属极收集纳秒脉冲放电中的高能电子,并转换为电信号后由示波器采集,为了获得更好的逃逸电子束流波形,对逃逸电子束流收集器进行了优化设计,提高了收集器的阻抗匹配特性,基于上述的逃逸电子束流收集器,研究了纳秒脉冲气体放电中逃逸电子的特征,实验结果表明,所设计的收集器可以有效地测量到逃逸电子束流,改进设计后收集器测得的逃逸电子柬流的时间分辨率和幅值均得到提高,施加电压约80 kV时,大气压空气中的逃逸电子束流幅值可达160 mA,脉宽小于1ns,多个脉冲激励放电的结果表明逃逸电子束流收集器具有较好的可靠性,其瞬态响应与时间分辨率比较稳定。     

High speed imaging of nanosecond-pulse dielectric barrier discharge in atmospheric air

使用上升沿40 ns、脉宽70 ns的重复频率单极性纳秒脉冲电源,采用双水电极结构产生大气压空气中介质阻挡放电.测量了纳秒脉冲下介质阻挡电压和电流,并获得长曝光时间和ns级曝光时间的放电特性,采用曝光时间为2 ns的高速摄影拍摄放电发展过程.结果表明:大气压空气中,水电极结构纳秒脉冲介质阻挡放电能够产生稳定均匀的放电等离子体,且存在二次放电.高速摄影对放电发展过程的拍摄结果表明:放电首先由电极中部开始发展,径向扩展至整个电极范围.     

空气中纳秒脉冲介质阻挡放电高速摄影

使用上升沿40 ns、脉宽70 ns的重复频率单极性纳秒脉冲电源,采用双水电极结构产生大气压空气中介质阻挡放电。测量了纳秒脉冲下介质阻挡电压和电流,并获得长曝光时间和ns级曝光时间的放电特性,采用曝光时间为2 ns的高速摄影拍摄放电发展过程。结果表明:大气压空气中,水电极结构纳秒脉冲介质阻挡放电能够产生稳定均匀的放电等离子体,且存在二次放电。高速摄影对放电发展过程的拍摄结果表明:放电首先由电极中部开始发展,径向扩展至整个电极范围。     

不同条件下大气压脉冲弥散放电特性

利用上升沿约0.5 s、半高宽约6 s、幅值可达40 kV的微秒脉冲电源和上升沿约150 ns、半高宽约300 ns、幅值可达50 kV的纳秒脉冲电源激励大气压弥散放电,并分别采用刀型和锯齿电极放电。通过电压电流测量和发光图像拍摄,改变施加电压种类、脉冲重复频率、高压电极结构和气隙距离等参数,研究了不同条件下弥散放电特性。实验结果表明:纳秒脉冲电源和微秒脉冲电源均能在大气压空气中激励大面积的弥散放电,弥散放电面积最大达90 cm2;放电的均匀性受脉冲参数与电极形状影响显著,其中刀型电极条件下纳秒脉冲激励的弥散放电均匀性最佳;相同条件下纳秒脉冲弥散放电的瞬时功率大于微秒脉冲弥散放电,最高可达275 kW,而纳秒脉冲弥散放电的能量小于微秒脉冲弥散放电;保持其他条件不变,弥散放电传导电流幅值随着气隙距离的增加而降低,放电强度随着脉冲重复频率的增加而增强,弥散放电的工作电压范围随着脉冲重复频率的增加显著降低。因此在低频、刀型电极结构中易于获得均匀与较大工作电压范围的大气压弥散放电。     

纳秒脉冲气体放电机理探讨

 经典Townsend机理和流注理论是气体放电研究的基础,但在解释纳秒脉冲气体放电时均存在一定缺陷。基于经典气体放电理论,探讨纳秒脉冲气体放电机理,分析流注理论判据在纳秒脉冲气体放电中的有效性,解释纳秒脉冲下电子逃逸现象和基于电子逃逸的快速电离波击穿理论,仿真计算高能快电子的逃逸过程。结果认为基于高能量快电子的逃逸击穿将是可能解释纳秒脉冲下气体放电现象的依据。     

纳秒脉冲下高能量快电子逃逸过程的计算

基于快电子的逃逸击穿机理将是一种能解释纳秒脉冲高过电压倍数下气体放电现象的理论，对高能量快电子的逃逸运动、碰撞电离引导电子崩的发展等进行了分析，并根据电子能量与阻力关系式，对电子的俘获或逃逸过程进行了计算.结果表明外加场强越高，更多的电子能逃逸，逃逸的能量阈值越低，气压对电子的逃逸过程影响也较大.同时也定性描述了纳秒脉冲下逃逸击穿放电过程. 关键词： 气体放电 快电子 逃逸击穿 纳秒脉冲     

纳秒脉冲下几种液态介质绝缘性能的比对

利用自行研制的纳秒脉冲实验平台(输出脉冲前沿30 ns,半宽百纳秒)和标准介电强度测试仪,对变压器油、甘油、去离子水、Galden HT200四种液体绝缘介质在直流与纳秒脉冲下的击穿特性进行了实验研究与结果比对,结果表明:在直流与纳秒脉冲下,Galden HT200均具有最高的击穿场强,且两种情况下均比变压器油高出40%以上;纳秒脉冲下,Galden HT200与变压器油的击穿场强均提高6.5~7倍,Galden HT200击穿过程耗时最短(ns量级),其次是变压器油(20 ns),然后依次为甘油(45 ns)和去离子水(70 ns);多次放电后,粘度系数最大的甘油更易在电极间隙处聚集碳化放电产物,粘度系数较小的Galden HT200和去离子水则无明显痕迹,但二者放电过程会产生明显的冲击波,多次放电后易造成间隙电极松动。     

Spectra of electrons and X-ray photons in a diffusive nanosecond discharge in air under atmospheric pressure

The spectra of electrons and X-ray photons generated in nanosecond discharges in air under atmospheric pressure are investigated theoretically and experimentally. Data for the discharge formation dynamics in a nonuniform electric field are gathered. It is confirmed that voltage pulses with an amplitude of more than 100 kV and a rise time of 1 ns or less causing breakdown of an electrode gap with a small-radius cathode generate runaway electrons, which can be divided into three groups in energy (their energy varies from several kiloelectronvolts to several hundreds of kiloelectronvolts). It is also borne out that the formation of the space charge is due to electrons appearing in the gap at the cathode and a major contribution to the electron beam behind the foil comes from electrons of the second group, the maximal energy of which roughly corresponds to the voltage across the gap during electron beam generation. X-ray radiation from the gas-filled diode results from beam electron slowdown both in the anode and in the gap. It is shown that the amount of group-3 electrons with an energy above the energy gained by runaway electrons (in the absence of losses) at a maximal voltage across the gap is much smaller than the amount of group-2 electrons.     

Energy distribution of runaway and fast electrons upon nanosecond volume discharge in atmospheric-pressure air

Nanosecond space discharge in a gas-filled diode is promising for pumping of lasers and high-power lamps. The space charge formed in the absence of an additional preionization source has a few advantages. The energy distributions of the beam electrons and the X-ray spectrum are determined. It is demonstrated that several high-energy electron bunches are formed in such a discharge. The main contribution to the beam current measured behind the foil is related to the runaway electrons, which have energies of tens or hundreds of kiloelectronvolts (supershort avalanche electron beam (SAEB)). Fast electrons with energies of several or tens of kiloelectronvolts are responsible for the generation of the soft X rays in the discharge gap. Anomalous electrons whose energy is higher than the voltage across the gap provide for a minor (less than 5%) contribution to the beam current. The generation time of these electrons is equal to the SAEB generation time accurate to 0.1 ns. It is demonstrated that the anomalous electrons can be generated owing to the acceleration in the presence of the field in front of the moving background-electron multiplication wave. The spectra of the X-ray radiation generated by the fast electrons in the volume are calculated.     

Generation of dual pulses of the runaway electron beam current during the subnanosecond breakdown of atomic and molecular gases

With a diaphragm placed behind the anode foil, dual runaway electron beams have been provided in helium, hydrogen, nitrogen, and air under a pressure of several torrs to several dozen torrs and a high-voltage pulse amplitude of about 250 kV. These beams consist of two pulses with commensurable amplitudes with a time interval between them of several dozen picoseconds to several hundred picoseconds. It has been shown that the breakdown of the interelectrode gap at pressures from several torrs to several dozen torrs may occur in different regimes and dual pulses of the electron beam current are registered when the initial current through the gap is below 1 kA. It has been found that a supershort avalanche electron beam that consists of one pulse is generated when the delay of breakdown equals several hundred picoseconds. It has been shown that, when the gas pressure reaches several hundred Torr, including atmospheric pressure, the runaway electrons are detected behind the foil after the termination of the supershort avalanche electron beam pulse.     

Streamers at the Subnanosecond Breakdown of Argon and Nitrogen in Nonuniform Electric Field at Both Polarities

An ICCD camera was used to study plasma glow at the stage of the streamer (ionization wave) formation in the tip–plane gap with a length of 3 mm filled with argon or nitrogen at a pressure of 12.5–400 kPa. Positive and negative nanosecond voltage pulses were applied across the gap. Images of streamer were obtained at different time at its propagation along the gap. A streak-camera equipped with a spectrometer was used to measure time evolution of the radiation intensity of nitrogen molecules at a wavelength of 337.1 nm in several regions along the gap at the negative polarity. Average streamer velocity (1.8 cm/ns) was estimated from experimental data at atmospheric pressure of nitrogen. Amplitude–time characteristics of voltage, discharge current and the current of runaway electron beam behind the aluminum-foil anode with a thickness of 10 μm were measured. Reasons for a diffuse discharge under the given experimental conditions were discussed.     

On the reconstruction of the energy distribution of electrons accelerated in solar flares

A technique for reconstructing energy spectra of electrons accelerated in solar flares is suggested that is based on the rigorous solution of the inverse problem considering their X-ray bremsstrahlung. Model calculations are made for various spectra, and it is proved that this technique makes it possible to find the electron energy distribution in real flare events. The energy distribution of high-energy electrons accelerated in the solar flare observed on July 26, 2002, is reconstructed. It is shown that the hard X-ray spectrum of the flare may result from the bremsstrahlung of three groups of high-energy electrons.     

Runaway of electrons in dense gases and mechanism of generation of high-power subnanosecond beams

New understanding of mechanism of the runaway electrons beam generation in gases is presented. It is shown that the Townsend mechanism of the avalanche electron multiplication is valid even for the strong electric fields when the electron ionization friction on gas may be neglected. A non-local criterion for a runaway electron generation is proposed. This criterion results in the universal two-valued dependence of critical voltage U _cr on pd for a certain gas (p is a pressure, d is an interelectrode distance). This dependence subdivides a plane (U _cr , pd) onto the area of the efficient electron multiplication and the area where the electrons leave the gas gap without multiplication. On the basis of this dependence analogs of Paschen’s curves are constructed, which contain an additional new upper branch. This brunch demarcates the area of discharge and the area of e-beam. The mechanism of the formation of the recently created atomospheric pressure subnanosecond e-beams is discussed. It is shown that the beam of the runaway electrons is formed at an instant when the plasma of the discharge gap approaches to the runaway electrons is formed at an instant when the plasma of the discharge gap approaches to the anode. In this case a basic pulse of the electron beam is formed according to the non-local criterion of the runaway electrons generation. The role of the discharge gap preionization by the fast electrons, emitted from the plasma non-uniformities on the cathode, as well as a propagation of an electron multiplication wave from cathode to anode in a dense gas are considered.