固相萃取-超高效液相色谱-三重四极杆质谱法测定水中15种抗生素残留

建立了固相萃取-超高效液相色谱-三重四极杆串联质谱(SPE-UPLC-MS/MS)测定水中磺胺类、喹诺酮类及四环素类抗生素的分析方法。考察了滤膜、固相萃取柱、洗脱液种类和体积、pH、上样流速对萃取效果的影响。水样过滤后调节至pH 3,经HLB小柱富集净化后,依次用0.1%(V:V)甲酸甲醇和3%(V:V)氨水甲醇洗脱,采用外标法定量分析。15种目标化合物在1～200μg/L范围内线性关系良好,检出限为0.15～1.04 ng/L;平均回收率在81.2%～116.6%之间,相对标准偏差(RSDs)为0.6%～8.9%。该方法适用于水中15种抗生素残留检测。     

在线固相萃取-液相色谱-串联质谱法测定环境水体中抗生素

应用在线固相萃取-液相色谱-串联质谱联用技术,定量检测地表水和污水处理厂废水中四环素类、磺胺类、大环内酯类、喹诺酮类和其他常见类抗生素化合物。水样经在线固相萃取小柱富集后,用乙腈-0.1%甲酸-5 mmol/L甲酸铵溶液为流动相洗脱并直接进入C18反相色谱柱分离,大气压电喷雾离子化串联质谱检测,同位素内标法定量。28种抗生素化合物含量在1~200 ng/L范围内均具有良好的线性响应,检出限低于0.7 ng/L。河水和污水厂废水的加标回收率分别在28%"120%和28%"125%范围。研究了EDTA和p H对水样处理回收率的影响。     

固相萃取/液相色谱-串联质谱法检测医院废水中21种抗生素药物残留

应用固相萃取及高效液相色谱-串联质谱技术,建立了医院废水中12种磺胺、4种喹诺酮、3种四环素以及罗红霉素和甲氧苄氨嘧啶等21种抗生素的定性定量方法。水样经HLB小柱萃取富集,使用10%甲醇溶液净化,经甲醇洗脱定容后,以高效液相色谱-串联质谱多反应监测离子模式(MRM)对目标物进行分析。在优化实验条件下,21种抗生素的线性范围为1.0～500μg/L,相关系数r2>0.99,方法检出限为0.005～0.022μg/L。在加标量为0.05μg/L和1.0μg/L时,空白加标回收率分别为71%～105%和76%～111%,RSD均小于15%。以医院废水为基质,21种抗生素的加标回收率为71%～135%,RSD小于25%。该方法简捷、快速、准确,能够实现医院废水中多种抗生素药物残留的同时分析。     

固相萃取-超高效液相色谱-三重四极杆质谱法测定海水中14种喹诺酮类抗生素

本研究采用固相萃取-超高效液相色谱-三重四极杆质谱联用技术，建立了海水中14种喹诺酮类抗生素的分析方法。将海水样品调至pH=2.0,加入0.5 g/L Na₂EDTA,经HLB固相萃取柱富集后，用甲醇洗脱，采用多反应监测模式进行检测。结果表明，14种喹诺酮类抗生素标准溶液线性关系良好，相关系数在0.998 7～0.999 9之间，以清洁海水为基质进行高、低浓度加标实验，回收率在74.9%～109.7%之间，精密度在4.7%～13.6%之间，符合质控要求。该方法检出限在0.015～0.561 ng/L之间，能够满足痕量分析要求。实样分析表明，该方法能够成功应用于海水中痕量喹诺酮类抗生素的分析，方法稳定可靠。     

超高效液相色谱-串联质谱法同时测定畜禽肉中磺胺类、喹诺酮类、硝基咪唑类兽药残留

建立了固相萃取-超高效液相色谱-串联质谱法同时测定畜禽肉中7种磺胺类、3种喹诺酮类及4种硝基咪唑类残留的方法。样品经乙腈提取,正己烷脱脂,MCX小柱净化后,由超高效液相色谱分离、三重四极杆质谱检测,基质外标法定量。14种兽药含量在1~50.0μg/L范围内线性关系良好,相关系数均大于0.994,加标回收率为75.2%~103.4%,检出限为0.1~0.5μg/kg,空白加标重复测定的相对标准偏差(n=6)为2.3%~12%。方法适用于畜禽肉中多种兽药残留的快速测定。     

全自动固相萃取-气相色谱/串联质谱法测定沉积物中的多氯联苯

建立了全自动固相萃取-三重四级杆串联质谱同时测定沉积物中27种多氯联苯的分析方法。样品经1:1(体积比)丙酮正己烷超声提取后经全自动固相萃取仪净化,采用气相色谱/三重四级杆串联质谱在多反映监测模式(MRM)下进行测定。在MRM模式下用两对离子对对多氯联苯进行分析,对母离子进行了碰撞能优化;27种多氯联苯的线性范围为2~200μg/L,线性的相关系数(r~2)﹥0.9945,方法检出限在0.023~0.060μg/kg之间,加标回收率为84.0%~118%,相对标准偏差﹤6.5%。     

聚(甲基丙烯酸-乙二醇甲基丙烯酸酯)微固相萃取-超高效液相色谱-串联质谱法测定水中雌激素

制备了聚(甲基丙烯酸-乙二醇甲基丙烯酸酯)有机聚合材料用于微固相萃取吸附剂,结合超高效液相色谱-串联三重四级杆质谱,建立了膜保护微固相萃取快速测定水体中E1、E2、E3、EE2和BPA 5种典型雌激素的方法。详细研究了萃取条件和解析条件对萃取效果的影响。在优化实验条件下,E3的检出限为0.2μg/L,线性范围为1～500μg/L,其余4种目标物检出限为0.02μg/L,线性范围为0.1～500μg/L。相对标准偏差均小于7.4%。方法用于实际污水处理厂污水中痕量雌激素的测定,样品加标回收率大于83%。     

SPE-UPLC-MS/MS同时测定水环境中4大类15种抗生素EI北大核心CSCD

建立了应用固相萃取-超高效液相色谱-串联质谱技术(SPE-UPLC-MS/MS)同时测定水环境中包括磺胺类、四环素类、大环内酯类和喹诺酮类在内的4大类15种抗生素的方法。采集的水样中加入同位素替代物后通过HLB固相萃取柱进行富集浓缩,UPLC-MS/MS进行测定,并采用内标法定量。结果表明,15种抗生素在0.5~50μg/L线性范围内检出限为0.04~0.09 ng/L,定量限为0.16~0.36 ng/L,样品加标回收率为59.5%~102.8%,相对标准偏差(RSD)均小于12%。该方法适用于水环境中痕量残留的抗生素检测。     

固相萃取/超高效液相色谱-质谱法筛查及检测养鱼河水中抗生素

建立了固相萃取/超高效液相色谱-串联三重四极杆质谱(UPLC-MS/MS)快速检测养鱼河水中4类(喹诺酮类、氯霉素类、四环素类以及磺胺类)15种抗生素的分析方法。取500 m L水样过滤,用盐酸调至p H4.0,加入0.5 g乙二胺四乙酸二钠(Na2EDTA)混匀后,再用HLB固相萃取柱对水样进行富集。利用超高效液相色谱-串联四极杆飞行时间质谱(UPLC-Q-TOF MS)结合基于UNIFI软件的常用抗生素数据库对养鱼河水中可能存在的抗生素进行快速筛查,筛查结果主要为喹诺酮类、氯霉素类、四环素类、磺胺类4类15种抗生素。为了提高检测结果的准确性,使用UPLC-MS/MS采用分时段多反应监测离子模式(MRM)分析样品中的抗生素,并用外标法定量。15种抗生素的空白基质加标回收率为61.0%~98.4%,相对标准偏差(n=3)为4.6%~14.0%,其线性关系良好,相关系数r≥0.990,检出限为0.01~0.3 ng/L。该方法灵敏度较高,重复性好,可用于对北京养鱼河水中抗生素的检测。     

固相萃取–超高效液相色谱三重四级杆质谱联用法测定水中四环素、土霉素及罗红霉素

建立了固相萃取–超高效液相色谱三重四级杆质谱联用法同时测定水中的罗红霉素、四环素和土霉素残留。水样经过固相萃取纯化、富集,液质联用分析,采用甲酸溶液和乙腈作为流动相,在5 min内完成对3种目标化合物的分析,3种目标化合物的方法检出限介于0.08~0.35 ng/L之间,测定结果的相对标准偏差为1.4%~5.6%,空白样品和实际样品的加标回收率分别为82.5%~114%,71.5%~126%。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.