Transition-metal coordination for complexing poly-(vinyl chloride)–polyurethane blends

Binary blends of poly(vinyl chloride) (PVC) and polyether polyurethane (PU) containing divalent transition metal (Zn²⁺) have been prepared by solution blending. The physical and mechanical properties of the blends are studied utilizing differential scanning calorimetry (DSC), thermogravimetry (TG), and tensile testing. The DSC results showed a high degree of molecular mixing of the two polymers. The glass transition temperatures (T_g) of the blends exhibited one major T_g whose position on the temperature scale is raised with increasing levels of PVC. The blends yielded stress–strain behavior similar to reinforced elastomers at low PVC, but at high PVC contents, they exhibited increased elongation. The latter materials showed well-developed yield points, stress whitening, and necking. Cold drawing was exhibited by the materials under tension. The tensile strength and Young's modulus were enhanced as the PVC content was increased.     

Morphology,dynamic mechanical,and electrical properties of bio‐based poly(trimethylene terephthalate) blends,part 2: Poly(trimethylene terephthalate)/poly(ether esteramide)/polycarbonate blends

Bio‐based poly(trimethylene terephthalate) (PTT) and poly(ether esteramide) (PEEA) blends were prepared by melt processing with varying weight ratios (0–20 wt %) of polycarbonate (PC). The blends were characterized by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), polarized light microscopy (PLM), and transmission electron microscopy (TEM). Electrostatic performance was also investigated for those PTT blends since PEEA is known as an ion conductive polymer. DMA suggests that PC is miscible with PEEA and selectively goes into PEEA phase in case of ternary blends of PTT/PEEA/PC. The glass transition temperature (T_g) for PC/PEEA is well predicted by Gordon Taylor equation. Addition of PC retards the electrostatic decay performance of PTT/PEEA blends by restricting the motion of ions in PEEA through increasing the T_g of PEEA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

A study of poly vinyl chloride / poly(butylene adipate-co-terephthalate) blends

Polymer blends were prepared by melt blending technique using poly vinyl chloride (PVC) and poly(butylene adipate-co-terephthalate) (PBAT). Different ratios of the blends were studied to investigate their mechanical, thermal and morphological properties. The FTIR spectrum indicated a slight increase of frequencies at C = O peak from 1714 to 1718 cm^-1 indicating a chemical interaction between C = O of PBAT and α-hydrogen of PVC. The tensile properties of PVC/PBAT blends highest at weight ratio of 50/50. The dynamic mechanical analysis (DMA) result proves that PVC and PBAT formed a miscible system with one glass transition temperature (T_g). The incorporation of PBAT results in a gradual decrease of the viscosity (loss modulus) and an increase of elasticity (storage modulus). The thermal properties of blend show the decomposition temperature of PVC in the blend decrease with the addition of PBAT. Scanning electron micrograph shows good interfacial adhesion on the tensile fractured surface of PVC/PBAT blend, which played important roles in enhancing the mechanical properties (strength and modulus).     

Blends of poly[3,3-bis(chloromethyl)oxetane] with poly(vinyl acetate). I. Thermal and mechanical properties

Blends of poly[3,3-bis(chloromethyl)oxetane] (Penton) with poly(vinyl acetate) were prepared. Compatibility, morphology, thermal behavior, and mechanical properties of blends with various compositions were studied using differential scanning calorimetry (DSC), dynamic mechanical measurements (DMA), tensile tests, and scanning electron microscopy (SEM). DMA study showed that the blends have two glass transition temperatures (T_g). The T_g of the PVAc rich phase shifts significantly to lower temperatures with increasing Penton content, suggesting that a considerable amount of Penton dissolves in the PVAc rich phase, but that the Penton rich phase contains little PVAc. The Penton/PVAc blends are partially compatible. DSC results suggest that PVAc can act as a β-nucleator for Penton in the blend. Marked negative deviations from simple additivity were observed for the tensile strength at break over the entire composition range. The Young's modulus curve appeared to be S-shaped, implying that the blends are heterogeneous and have a two-phase structure. This was confirmed by SEM observations. © 1992 John Wiley & Sons, Inc.     

Polymer compatibility enhancement via ion-ion and ion-dipole interactions: Ternary blends of polyurethane, poly(vinyl chloride) and poly(styrene-co-maleic anhydride)

Summary Ternary polymer blends (TPB) based on polyurethane (PU) containing tertiary amine, poly(vinyl chloride) (PVC), and poly(styrene-co-maleic anhydride) (SMA) containing 6.25% maleic acid were prepared via solution technique. The blends were investigated by using differential scanning calorimetry (DSC), dynamic mechanical (DMA), stress-strain testing, and density. DSC, DMA and density results showed extensive molecular mixing of the three polymer components through ion pair-ion pair, ion pair-dipole and dipole-dipole interactions. The glass transition temperatures (Tg) of TPBs gradually merged from two distinct transitions to one transition temperature. The mechanical properties of TPBs exhibited synergistic behavior with respect to tensile strength and the stress-strain behavior similar to reinforced elastomers at low PVC or SMA contents and well-developed yield points, stress whitening and necking at high PVC or SMA contents. Received: 14 December 1997/Accepted: 3 February 1998     

Thermal and dynamic mechanical properties of microwave and heat‐cured poly(methyl methacrylate) used as dental base material

In this study, the particle size distribution, molecular weight, thermal analysis (TGA) differential scanning calorimetry (DSC) and thermogravimetric analysis, and dynamic mechanical analysis (DMA) of poly(methyl methacrylate) used as dental base material were investigated. The commercial raw material used were prepared for microwave curing, and they were cured by microwave and conventional heat methods. The average particle size of the powder studied (103.1 μm) were much larger than that of the commercial powders (50–78 μm) for conventional curing. The particle size dietribution were almost symmetrical and narrow. The viscosity‐average molecular weight were larger for microwave curing and increased with curing time. The glass transition temperature T_g measured (about 110°C) by DSC increased with curing period in microwave oven. The values of T_g were close to each other for both curing techniques. The degradation temperature range observed by TGA were 200–377°C. The movements of molecular chains in their conformations were studied by DMA in the form of changes in different mechanical properties with temperature. It was shown that crosslinking increased with increase of curing time. The changes were more noticeable in microwave curing compared to conventional heat curing. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2971–2978, 1999     

Studies on polyblends of poly(vinyl chloride) and acrylonitrile-butadiene-styrene terpolymer

Blends of poly (vinyl chloride) (PVC) and acrylonitrile-butadiene styrene (ABS) terpolymer were prepared in different ratios by a melt blending technique. ABS containing three different levels of rubber content were used. A quantitative assessment of ABS in PVC/ABS blends has been shown by infrared studies. ABS content has been shown as the presence of the characteristic acrylonitrile peak. Differential scanning calorimetry (DSC) studies have been carried out to study the glass transition (T_g) behavior of the blends. Two T_g values corresponding to PVC and styrene-acrylonitrile (SAN) copolymer have been observed. Thermogravimetric analysis (TGA) reveals a significant improvement in thermal stability of these blends as compared to PVC. Mechanical properties show a significant increase in the impact strength which is related to rubber content of the ABS used. Morphological studies have been carried out by scanning electron microscopy which support the observation that an increase in rubber content results in greater ductility.     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(styrene‐co‐acrylonitrile)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMAs) (designated as iPMMA, aPMMA, and sPMMA) with approximately the same molecular weight were mixed separately with poly(styrene‐co‐acrylonitrile) (abbreviated as PSAN) containing 25 wt % of acrylonitrile in tetrahydrofuran to make three polymer blend systems. Differential scanning calorimetry (DSC) was used to study the miscibility of these blends. The results showed that the tacticity of PMMA has a definite impact on its miscibility with PSAN. The aPMMA/PSAN and sPMMA/PSAN blends were found to be miscible because all the prepared films were transparent and showed composition dependent glass transition temperatures (T_gs). The glass transition temperatures of the two miscible blends were fitted well by the Fox equation, and no broadening of the glass transition regions was observed. The iPMMA/PSAN blends were found to be immiscible, because most of the cast films were translucent and had two glass transition temperatures. Through the use of a simple binary interaction model, the following comments can be drawn. The isotactic MMA segments seemed to interact differently with styrene and with acrylonitrile segments from atactic or syndiotactic MMA segments. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2894–2899, 1999     

Thermal properties and non‐isothermal crystallization behavior of biodegradable poly(p‐dioxanone)/poly(vinyl alcohol) blends

Blends of two biodegradable semicrystalline polymers, poly(p‐dioxanone) (PPDO) and poly(vinyl alcohol) (PVA) were prepared with different compositions. The thermal stability, phase morphology and thermal behavior of the blends were studied by using thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). From the TGA data, it can be seen that the addition of PVA improves the thermal stability of PPDO. DSC analysis showed that the glass transition temperature (T_g) and the melting temperature (T_m) of PPDO in the blends were nearly constant and equal to the values for neat PPDO, thus suggesting that PPDO and PVA are immiscible. It was found from the SEM images that the blends were phase‐separated, which was consistent with the DSC results. Additionally, non‐isothermal crystallization under controlled cooling rates was explored, and the Ozawa theory was employed to describe the non‐isothermal crystallization kinetics. Copyright © 2006 Society of Chemical Industry     

Blends of the alternating ethylene–tetrafluoroethylene copolymer with poly(vinylidene fluoride)

Blends of the alternating ethylene–tetrafluoroethylene copolymer (ETFE) with poly(vinylidene fluoride) (PVF₂) were prepared by melt-mixing. Compatibility, morphology, thermal behavior, and mechanical properties of the ETFE/PVF₂ blends with various compositions were studied by using differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD), dynamic mechanical analysis (DMA), thermogravimetric analysis (TGA), tensile tests, and scanning electron microscopy (SEM). DMA studies showed that the blends have separate glass transition temperatures (T_g) close to those of the pure polymers. ETFE and PVF₂ are incompatible. Marked negative deviations from simple additivity were observed for both the ultimate strength and the elongation at break over the entire composition range. The interfaces between ETFE and PVF₂ are weakly bonded with rather poor interaction. SEM observations revealed that the blends have a two-phase structure and the adhesion between the phases is poor. © 1997 John Wiley & Sons, Inc. J Appl Polm Sci 65:295–304, 1997     

Preparation of epoxidized cardanol butyl ether as a novel renewable plasticizer and its application for poly(vinyl chloride)

A new type of plasticizer, epoxidized cardanol butyl ether (ECBE), was synthesized via etherification and epoxidation. Successful synthesis was confirmed from Fourier transform infrared, ¹H NMR and ¹³C NMR spectra. The obtained product was evaluated by adding it to poly(vinyl chloride) (PVC) incorporated with dioctyl phthalate (DOP). Mechanical and thermal properties of PVC blends were studied using tensile testing, thermogravimetric analysis (TGA) and dynamic mechanical analysis (DMA). Processability, migration and volatility of plasticizing systems were also investigated. Tensile tests found a maximum increase of 17.8% in elongation at break. DMA results indicated that glass transition temperature shifted to lower temperature with a maximum decrease of 5.76 °C. TGA results revealed that PVC blends with higher content of ECBE had higher thermal stability; initial degradation temperature, 50% weight loss temperature and the first peak degradation temperature increased by 15.3, 14.8 and 4.1 °C, respectively. Processing time was extended from 11.56 to 59.94 min. The plasticizing performance of migration and volatility resistance were higher than those of neat DOP. © 2016 Society of Chemical Industry     

Determination of optimum blending conditions for poly(vinyl chloride)/epoxidized natural rubber blends

An attempt to resolve the difficulties normally faced in preparing PVC-dominant PVC/ENR blends with the Brabender plasticorder is discussed. As expected, it was found that the mechanical properties of PVC/ENR blends are greatly influenced by the mixing parameters, which are further reinforced with evidence from both dynamic mechanical analysis (DMA) and morphological studies. Both techniques showed the attainment of compatible 50/50/PVC/ENR blends, the former a single glass transition temperature (T_g) and the latter a single-phase system, albeit their inherent properties are dependent on the blending parameters. By utilizing the correlation between mixing temperature and rotor speed derived, good PVC/ENR blends can be easily procured. © 1993 John Wiley & Sons, Inc.     

Mechanical and thermal properties of glass bead–filled nylon‐6

The mechanical and thermal properties of glass bead–filled nylon‐6 were studied by dynamic mechanical analysis (DMA), tensile testing, Izod impact, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) tests. DMA results showed that the incorporation of glass beads could lead to a substantial increase of the glass‐transition temperature (T_g) of the blend, indicating that there existed strong interaction between glass beads and the nylon‐6 matrix. Results of further calculation revealed that the average interaction between glass beads and the nylon‐6 matrix deceased with increasing glass bead content as a result of the coalescence of glass beads. This conclusion was supported by SEM observations. Impact testing revealed that the notch Izod impact strength of nylon‐6/glass bead blends substantially decreased with increasing glass bead content. Moreover, static tensile measurements implied that the Young's modulus of the nylon‐6/glass bead blends increased considerably, whereas the tensile strength clearly decreased with increasing glass bead content. Finally, TGA and DSC measurements indicated that the thermal stability of the blend was obviously improved by incorporation of glass beads, whereas the melting behavior of the nylon‐6 remained relatively unchanged with increasing glass bead content. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1885–1890, 2004     

Miscibility in poly(vinyl chloride)/chlorinated poly(vinyl chloride) blends,and blends of different chlorinated poly(vinyl chlorides)

Blends of poly(vinyl chloride) with chlorinated poly(vinyl chloride) (PVC), and blends of different chlorinated poly(vinyl chlorides) (CPVC) provide an opportunity to examine systematically the effect that small changes in chemical structure have on polymer-polymer miscibility. Phase diagrams of PVC/CPVC blends have been determined for CPVC's containing 62 to 38 percent chlorine. The characteristics of binary blends of CPVC's of different chlorine contents have also been examined using differential calorimetry (DSC) and transmission electron microscopy. Their mutual solubility has been found to be very sensitive to their differences in mole percent CCl₂ groups and degree of chlorination. In metastable binary blends of CPVC's possessing single glass transition temperatures (T_g) the rate of phase separation, as followed by DSC, was found to be relatively slow at temperatures 45 to 65° above the T_g of the blend.     

Structure–property behavior of gamma‐irradiated poly(styrene) and poly(methyl methacrylate) miscible blends

Polymer blends based on various ratios of polystyrene (PS) and polymethyl methacrylate (PMMA) were exposed to different doses of gamma radiation up to 25 Mrad. The structure–property behavior of the polymer blends before and after they had been irradiated was investigated by DSC, TGA, and FTIR spectroscopy. The DSC scans of the glass transition temperature (T_g) of the different polymer blends showed that the T_g was greatly decreased by increasing the ratio of the PMMA component in the polymer blends. Moreover, the T_g of PS/PMMA blends was found to decrease with increasing irradiation dose. The depression in T_g was noticeable in the case of blends rich in PMMA component. The TGA thermograms showed that the thermal stability of the unirradiated polymer blends decreases with increasing the ratios of PMMA component. Also, it was found that the presence of PS polymer in the blends affords protection against gamma radiation degradation and improves their thermal stability. However, exposing the polymer blends to high doses of gamma radiation caused oxidative degradation to PMMA components and decreased the thermal stability. The investigation of the kinetic parameters of the thermal decomposition reaction confirm the results of thermal stability. The FTIR analysis of the gamma‐irradiated polymer blend films gives further support to the TGA data. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 509–520, 1999     

Ionomeric blends of poly(ethylene oxide) with poly(styrene‐co‐maleic anhydride) ionomer: Miscibility,crystallization, and melting behavior

The miscibility and crystallization behavior of poly(ethylene oxide) (PEO) and poly(styrene‐co‐maleic anhydride) ionomer (SMAI) blends were studied by the dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC). This study has demonstrated that the presence of ion–dipole interactions enhances the miscibility of otherwise immiscible polymers in the PEO and high molecular weight poly(styrene‐co‐maleic anhydride) (SMA). The effect of ion–dipole interactions on enhancing miscibility is confirmed by the presence of a single glass transition temperature (T_g) and a depression of the equilibrium melting temperature of the PEO component. The equilibrium melting temperature of PEO in the blends are obtained using Hoffman‐Weeks plots. The interaction energy density, β, is calculated from these data using the Nishi‐Wang equation. The results suggest that PEO and SMAI blends are thermodynamically miscible in the melt. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1–7, 2000     

Evaluating effects of biobased 2,5‐furandicarboxylate esters as plasticizers on the thermal and mechanical properties of poly (vinyl chloride)

We synthesized 2,5‐furandicarboxylate esters [i.e., dibutylfuran‐2,5‐dicarboxylate, diisoamylfuran‐2,5‐dicarboxylate, and di(2‐ethylhexyl)furan‐2,5‐dicarboxylate] and investigated their potential application as plasticizers of commercial poly(vinyl chloride) (PVC) products. Fourier transform infrared analysis, mechanical tests, scanning electron microscopy investigation, differential scanning calorimetry analysis, dynamic mechanical thermal analysis, thermogravimetric analysis (TGA), melt flow rate (MFR) measurement, and plasticizer migration measurements were used to the evaluate the comprehensive properties of the blended products. The results of the tensile tests demonstrate that the blends exhibited antiplasticization and flexible plastic characteristics at 10 and 50 phr in PVC, respectively. Moreover, flexural and impact test data indicate that the three types of blends exhibited a similar tendency: the hardness decreased continuously as the amount of plasticizer increased. Their morphology indicated that all of the plasticizers had good compatibility with PVC. The resulting glass‐transition temperature of the investigated plasticizers was lower than that of pure PVC, and reduction was largest for the plasticizer with the highest molecular weight. TGA revealed that the thermal degradation of blended polymers occurred in three stages and that all of the blends were stable up to 180°C. Finally, the MFRs of all of the specimens indicated that the addition of a higher concentration of lower molecular weight biobased esters resulted in improved fluidity, but these compounds migrated more easily from the blends. Hence, 2,5‐furandicarboxylic acid derived from biomass has potential as a plasticizer. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40938.     

Miscible blends of biobased poly(lactide) with poly(methyl methacrylate): Effects of chopped glass fiber incorporation

Poly(lactide) (PLA) and poly(methyl methacrylate) (PMMA) are melt compounded with chopped glass fiber using laboratory scale twin‐screw extrusion. Physical properties are examined using differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), tensile testing, impact testing, X‐ray computed tomography (CT) scanning, and field emission scanning electron microscopy (FE‐SEM). Molecular weight is determined using gel permeation chromatography (GPC). Miscibility of the blends is implied by the presence of a single glass transition temperature and homogeneous morphology. PLA/PMMA blends tend to show positive deviations from a simple linear mixing rule in their mechanical properties (e.g., tensile toughness, modulus, and stress at break). The addition of 40 wt % glass fiber to the system dramatically increases physical properties. Across all blend compositions, the tensile modulus increases from roughly 3 GPa to roughly 10 GPa. Estimated heat distortion temperatures (HDTs) are also greatly enhanced; the pure PLA sample HDT increases from 75 °C to 135 °C. Fiber filled polymer blends represent a sustainable class of earth abundant materials which should prove useful across a range of applications. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44868.     

Miscibility,phase behavior,and mechanical properties of ternary blends of poly(vinyl chloride)/polystyrene/chlorinated polyethylene-graft-polystyrene

The effectiveness of chlorinated polyethylene-graft-polystyrene (CPE-g-PS) as a polymeric compatibilizer for immiscible poly(vinyl chloride)/polystyrene (PVC/PS) blends was investigated. The miscibility, phase behavior, and mechanical properties were studied using differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), Izod impact tests, tensile tests, and scanning electron microscopy (SEM). DSC and DMA studies showed that PVC is immiscible with chlorinated polyethylene (CPE) in CPE-g-PS, whereas the PS homopolymer is miscible with PS in CPE-g-PS. The PVC/PS/CPE-g-PS ternary blends exhibit a three-phase structure: PVC phase, CPE phase, and PS phase that consisted of a PS homopolymer and PS in CPE-g-PS. The mechanical properties showed that CPE-g-PS interacts well with both PVC and PS and can be used as a polymeric compatibilizer for PVC/PS blends. CPE-g-PS can also be used as an impact modifier for both PVC and PS. SEM observations confirmed, after the addition of CPE-g-PS, improvement of the interfacial adhesion between the phases of the PVC/PS blends. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 995–1003, 1998     

Characterization of 1,5‐pentanediol dibenzoate as a potential “green” plasticizer for poly(vinyl chloride)

1,5‐Pentanediol dibenzoate (PDDB) was evaluated as a potential “green” plasticizer for poly(vinyl chloride) (PVC) at concentrations ranging between 20 and 80 parts by weight per hundred parts of resin. The results of glass transition temperature (T_g) and tensile tests of PDDB blends with PVC were compared with those for blends of the commercial plasticizers di(2‐ethylhexyl) phthalate (DEHP), di(ethylene glycol) dibenzoate (DEGDB), and di(propylene glycol) dibenzoate (DPGDB) in PVC. The depression in T_g and the tensile properties were comparable for a PDDB/PVC blend at a fixed composition to those of blends with DEHP, DEGDB, and DPGDB. The PDDB was subjected to biodegradation using co‐metabolism by the common soil bacterium Rhodococcus rhodochrous (ATCC 13808). After 16 days of growth, nearly all of the PDDB was degraded, and only small amounts of transient, unidentified metabolites were observed in the growth medium during the experiment. J. VINYL ADDIT. TECHNOL., 2009. © 2009 Society of Plastics Engineers