介孔碳基钴镍氧化物的电化学电容性能

以介孔碳CMK-3为载体,利用CMK-3表面缺陷作形核中心,应用前驱体化学液相共沉淀法制备新型的Co0.25Ni0.75氧化物/CMK-3复合材料.X射线衍射（XRD）分析及扫描电子显微镜（SEM）形貌观察表明该材料主要呈现弱结晶态结构,其中Co-Ni氧化物纳米片交错成空间网络并包覆在介孔碳表面.BET测试表明该材料孔径分布在3~4 nm之间,且高分散、疏松多孔,具有良好的OH-离子传递特性.循环伏安和恒流充放电测试表明,该材料有高的电化学活性, 在5 mA/cm2电流密度下,Co0.25Ni0.75氧化物（92%）/C比电容达1781F/g.     

Co(OH)2/Ni(OH)2复合电极材料制备及其超级电容性质

以Co(NO_3)_2·6H_2O和Ni(NO_3)_2·6H_2O为钴源和镍源,采用溶剂热法一步合成了Co(OH)_2/Ni(OH)_2复合材料,通过煅烧该复合材料可得到NiCo_2O_4。采用XRD、SEM、BET等对材料进行了表征,结果表明,Co(OH)_2/Ni(OH)_2复合材料是薄片组成的花状形貌,比表面积为37. 48m~2/g。电化学性能测试表明,Co(OH)_2/Ni(OH)_2复合材料比NiCo_2O_4具有更高的比电容值和容量保持率。在0. 5A/g的电流密度下,复合材料比电容值可达到1097. 8F/g,而NiCo_2O_4比电容值仅为86. 1F/g。因此,与煅烧后的NiCo_2O_4材料相比,Co(OH)_2/Ni(OH)_2复合材料具有更加优良的电化学性能,这为高性能超级电容器材料的制备提供了一个新思路。     

载铜介孔碳CMK-3的制备及其对苯酚的吸附-催化氧化性能

通过一种简易的方法在介孔碳CMK-3的孔道内负载氧化铜粒子制备Cu/CMK-3复合物,利用粉末X射线衍射、氮气吸附-脱附、透射电镜等手段对其进行表征.结果表明,氧化铜均匀地分散在CMK-3孔道中,CMK-3在负载氧化铜后仍有较大的比表面积.考察了载铜CMK-3对水中苯酚的吸附和低温干法催化氧化苯酚性能.吸附和循环使用结果表明,Cu/CMK-3对水中苯酚具有较大的吸附量和良好的催化氧化效率.热重-质谱(TG-MS)联用测试结果表明,吸附的苯酚在180℃左右开始被催化氧化为CO2和水,此时不会造成苯酚的脱附和介孔碳CMK-3的烧蚀.     

不同载体负载的铂催化剂在丙酮酸乙酯不对称氢化反应中的活性及其铂流失率比较

以介孔树脂材料FDU-14和介孔碳材料CMK-3为载体制备了两种负载型铂催化剂, 用N₂气吸附、X射线衍射及CO化学吸附等手段对这两种催化剂进行了表征, 并将这两种不同的负载型铂催化剂在丙酮酸乙酯不对称氢化反应中的催化性能及其铂流失率与商品化Pt/Al₂O₃催化剂进行了比较. 研究结果表明, 尽管Pt/Al₂O₃催化剂的初始活性和光学选择性均较高, 然而相同反应条件下乙酸溶剂中Pt/FDU-14和Pt/CMK-3催化剂的铂流失率比Pt/Al₂O₃催化剂的低. 通过对催化剂进行CO吸附原位傅里叶变换红外漫反射光谱(DRIFTS)表征, 从载体的不同表面电子性质角度解释了不同载体负载的铂催化剂在丙酮酸乙酯不对称氢化反应中的活性和铂流失率的差异.     

皱褶表面介孔镍钴硫化物微球的制备及其超电性能

通过一步水热法分别合成了α-NiS、Co₃S₄和CoNi₂S₄纳米介孔电极材料,并研究了其电化学性能。 X射线衍射(XRD)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)研究表明,介孔硫化物是由单相纳米颗粒堆叠组装而成,其中二元系的CoNi₂S₄由纳米片自组装形成了具有皱褶表面的微球形貌。 电化学性能研究表明,二元系的CoNi₂S₄比α-NiS、Co₃S₄具有更高的比电容、更佳的倍率特性和优异的循环稳定性。 在扫描速率为5 mV/s时,CoNi₂S₄材料在6 mol/L KOH电解液中比电容高达1678.3 F/g,优于α-NiS (787.4 F/g)和Co₃S₄(1532.7 F/g),在扫描速率从5 mV/s增加到100 mV/s时,其电容保持率为45.8%,比α-NiS(30.2%)和Co₃S₄(29.3%)高出约15%。 在15A/g的电流密度下,经过900次循环充-放电后,二元系的CoNi₂S₄的电容仍保持在96.3%,库伦效率保持在94.3%左右,说明镍钴双金属硫化物具有优异的循环稳定性能和充放电可逆性。     

综合利用稻壳制备木糖、电容炭与硅酸钙晶须

利用酸水解稻壳中的半纤维素制备木糖, 并将糖渣经过炭化后分离出碳和硅, 碳采用稀碱溶液活化改性制备电容炭, 硅采用水热法合成了硅酸钙晶须, 从而使稻壳所有组分得到充分利用. 采用循环伏安(CV)和恒流充放电(GCD)研究了电容炭的电化学性能. 通过X射线衍射(XRD)和扫描电子显微镜(SEM)对所得硅酸钙晶须的结构和形貌进行了表征. 实验结果表明, 稻壳酸水解的最优条件为硫酸浓度7%(质量分数)、 固液比(g/mL)为1:8、 反应时间为2.0 h, 在该条件下, 一次水解、 二次水解和三次水解的木糖收率(Y₁/Y₂/Y₃)和浓度(质量分数, C₁/C₂/C₃)都能达到最大值, Y₁=98.5%, C₁=3.6%; Y₂=85.4%, C₂=6.3%; Y₃=76.6%, C₃=9.0%. 采用15 mL 8%(质量分数) NaOH稀碱溶液活化改性制得的电容炭(AC/15)比电容值为77.32 F/g, 而且具有较好的倍率性和循环稳定性; 硅酸钙晶须为扫帚状针钠钙石晶须.     

Al3+离子掺杂δ-MnO2的制备和电化学性能

采用水热法合成了不同比例Al³⁺离子掺杂的δ-MnO₂纳米粉体.通过X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、 X射线光电子能谱(XPS)、循环伏安(CV)曲线、电化学阻抗谱(EIS)和恒电流充放电(GCD)曲线等手段对材料的结构和电化学性能进行了表征.结果表明, Al³⁺离子进入δ-MnO₂的晶格替代部分Mn³⁺和Mn⁴⁺离子,使得δ-MnO₂电极的性能明显提升.当反应物中Al³⁺/Mn²⁺摩尔比为0.45时,所得样品(A0.45M)的性能最好;其在1 A/g电流密度下的比电容为207.61 F/g,是纯相δ-MnO₂(A0M)的2.4倍;其在10 A/g电流密度下循环10000次后的比电容为100.81 F/g,容量保持率为81.33%.     

绿色合成介孔碳负载(Ni)MoS2加氢脱硫催化剂

以Anderson结构Ni-Mo杂多酸簇(NH₄)₄[NiMo₆O₂₄H₆]·5H₂O、硫脲、柠檬酸、氯化钠为原料,采用冻干法得到前驱体后焙烧、洗涤得到介孔碳骨架负载(Ni)MoS₂纳米颗粒的加氢脱硫催化剂,考察了其对二苯并噻吩的加氢脱硫活性,并采用X射线衍射、N₂低温吸附-脱附、拉曼光谱、X光电子能谱、扫描电子显微镜、高分辨透射电镜、程序升温还原等表征手段对催化剂进行了分析。结果表明,介孔碳骨架负载(Ni)MoS₂纳米颗粒催化剂具有较弱的载体-金属相互作用,MoS₂纳米颗粒平均长度较短(4.9 nm),层数适宜(4.8),NiMoS活性相含量较高,二苯并噻吩的转化率可达94.1%,反应速率常数及活性位转换频率分别可达1.7×10^-6 mol/(g·s)和2.8×10^-3 s^-1。该方法利用原位生成的氯化...     

生物质纳米碳膜的制备及其电化学性能

将衰老叶片用H₂SO₄进行水热氧化得到氧化水合碳前驱体，前驱体经烘干研磨在KOH存在下进行碳化得到生物质纳米碳膜(LS-OCM),通过FT-IR,XRD、TEM、SEM、AFM、XPS及N₂吸附-脱附等测试手段对其材料组成和微观形貌进行表征。TEM、SEM及N₂吸附-脱附分析显示，制得生物质纳米碳膜材料(LS-OCM)既保留叶片原有的叶脉结构又形成丰富多级的孔道结构，比表面积约为450.7 m²/g,孔径分布较窄，平均孔径为3.8 nm; AFM分析显示，LS-OCM类似二维纳米膜，片层平均厚度在1.6 nm左右；XPS及XRD分析表明，该材料中C主要以C=C形似存在，为类石墨烯碳膜。电化学性能分析表明，在电流密度为0.25 A/g下，LS-OCM比电容为262.58 F/g,循环100圈，比电容仍然可达150.8 F/g,表明材料具有良好的稳定性。     

介孔碳负载铂催化剂的分散性和电催化活性

以介孔硅SBA-15为模板, 糠醇为碳源制备了高度有序的介孔碳(CMK-5), 并用微波法合成碳负载的铂纳米粒子的催化剂. 为改善铂微粒的分散性能, 在微波碳载过程中添加了适量的阳离子表面活性剂(CTAB). XRD和TEM测试结果表明, CTAB的加入改善了铂催化剂的分散性, 且使铂微粒的平均粒径降至2.9 nm左右. 循环伏安测试结果显示, 加入CTAB后所得Pt/CMK-5催化剂的电化学活性面积大于未加CTAB的以及商业Johnson Matthey公司的Pt/C催化剂的活性面积.     

有序介孔碳CMK-3的化学活化及储氢性能

选用KOH、NaOH、H3PO4对有序介孔碳CMK-3进行了活化,通过X射线衍射、低温氮吸附-脱附等对样品进行了表征,发现活化后样品的结构发生了巨大的变化。有序介孔碳CMK-3的有序性逐渐降低,比表面积明显增大,2 nm介孔明显增多。讨论了CMK-3和KOH质量比、活化温度、不同活化剂对活化效果的影响。储氢测试表明活化能够明显提高CMK-3的储氢性能,77K、100 kPa时的储氢性能高达2.32wt%。     

Ammonia-treatment assisted fully encapsulation of Fe2O3 nanoparticles in mesoporous carbons as stable anodes for lithium ion batteries

To improve the initial coulombic efficiency and bulk density of ordered mesoporous carbons, active Fe₂O₃ nanoparticles were introduced into tubular mesopore channels of CMK-5 carbon, which possesses high specific surface area (>1700 m²·g^?1) and large pore volume (>1.8 cm³·g^?1). Fine Fe₂O₃ nanoparticles with sizes in the range of 5–7 nm were highly and homogenously encapsulated into CMK-5 matrix through ammonia-treatment and subsequent pyrolysis method. The Fe₂O₃ loading was carefully tailored and designed to warrant a high Fe₂O₃ content and adequate buffer space for improving the electrochemical performance. In particular, such Fe₂O₃ and mesoporous carbon composite with 47 wt% loading exhibits a considerably stable cycle performance (683 mAh·g^?1 after 100 cycles, 99% capacity retention against that of the second cycle) as well as good rate capability. The fabrication strategy can effectively solve the drawback of single material, and achieve a high-performance lithium electrode material.     

Synthesis, characterization, and electrochemical properties of ordered mesoporous carbons containing nickel oxide nanoparticles using sucrose and nickel acetate in a silica template

New ordered mesoporous carbons containing nickel oxide nanoparticles have been successfully synthesized by carbonization of sucrose in the presence of nickel acetate inside SBA-15 mesoporous silica template. The obtained samples were characterized by X-ray diffraction (XRD), nitrogen adsorption-desorption, and transmission electron microscopy (TEM). The NiO nanoparticles were embedded inside the mesoporous carbon framework due to the simultaneous pyrolysis of nickel acetate during carbonization. The electrochemical testing of the as-made nanocomposites showed a large specific capacitance of 230 F g⁻¹ using 2 M KOH as the electrolyte at room temperature. This is attributed to the nanometer-sized NiO formed inside mesoporous carbons and the high surface area of the mesopores in which the NiO nanoparticles are formed. Furthermore, the synthetic process is proposed as a simple and general method for the preparation of new functionalized mesoporous carbon materials, for various applications in catalysis, sensor or advanced electrode material.     

Facile synthesis of ordered mesoporous molybdenum carbide electrocatalysts for high-performance hydrogen evolution reaction

In this study, a simple method was designed to prepare ordered mesoporous carbons embedded with molybdenum without any extreme conditions. We prepared three different ordered molybdenum carbide materials with mesoporous structures to explore the influence of the structure of molybdenum-based materials on the HER catalytic efficiency. The ordered mesoporous molybdenum carbide catalysts (CMK-3-MoCx, fCMK-3-MoCx, CMK-8-MoCx) were characterized by SEM, TEM, XRD, nitrogen adsorption-desorption and XPS. The HER is catalyzed efficiently on the three electrocatalysts, fCMK-3-MoCx shows the best HER electro-catalytic performance with a small onset potential of −0.06 V vs. RHE, a low tafel slope of 66 mV dec⁻¹ and a small over-potential value of 89 mV at 10 mA cm⁻². This excellent performance on HER is due to its high specific surface area and highly ordered mesoporous structure that resulted in excellent proton transport efficiency and high electron transfer rate. Our results provide a new research direction for the application of flat ordered mesoporous structures in catalysis.     

Synthesis and characterization of nanocast silica NCS-1 with CMK-3 as a template

Nanocast silica (NCS-1) was synthesized by a casting process by employing the mesoporous carbon CMK-3 (the replica of SBA-15) as a template, tetraethoxysilane (TEOS) as the silica source, and hydrochloric acid (HCl) as the catalyst. The ordered carbon template was removed by employing different methods, such as calcination, thermal treatment followed by calcination, and controlled combustion. According to XRD and TEM characterization, NCS-1 exhibits an ordered structure with hexagonal symmetry and retains the morphology of the original SBA-15 used for the synthesis of CMK-3 over two replication steps on the nanometer scale. This demonstrates the well-connected porosity in CMK-3 type carbon, which can be used as a mold to synthesize mesostructured materials. The nitrogen adsorption isotherms generally show type IV shape, indicating mesoporous characteristics. The structure of NCS-1 is strongly influenced by variables of the nanocasting process, such as the loading amount of silica, hydrolysis temperature, and carbon removal methods. The surface area, pore size, and pore volume of NCS-1 can be tuned to a certain range by varying these parameters.     

Surface functionalization of ordered mesoporous carbons--a comparative study

Hexagonally structured mesoporous carbons C15 and CMK-5 and cubically structured carbon C48 were synthesized using ordered silica SBA-15 and MCM-48 as templates and carbon precursors of different structures. The surfaces of these ordered carbons were chemically functionalized by employing an approach, in which the selected diazonium compounds were in situ generated and reacted with the carbon frameworks of the mesoporous carbons. The aromatic organic molecules containing chlorine, ester, and alkyl groups were covalently attached to the surface of these ordered mesoporous carbons. The presence of functional groups on the modified carbons was confirmed with Fourier transform infrared spectroscopy, thermogravimetric analysis, and nitrogen adsorption. The BET-specific surface area and the pore width of ordered carbons were significantly reduced, whereas the primary structure of these ordered carbons and their unit cells were intact. Basically, the density of grafted functional groups is related to the specific surface area of the sample, particularly the surface area of mesopores. The surface functionalization reaction takes place only on the external surface of carbon C15, while it occurs on both of the internal and external surface of CMK-5 carbon with the nanopipe structure. The presence of the micropores in CMK-5 carbon should be responsible for its lower grafting density because the small micropores are inaccessible in the reaction. It was also proposed that the preferred adsorption/reaction in C48 may be related to the observed unsymmetrical degradation of the XRD patterns for the functionalized C48 samples. The chemical modification process considerably reduced the primary mesopores in these ordered carbons by approximately 1-1.5 nm, affording carbons with micropores in the cases of C15 and C48, and mixed micropores and small mesopores in the case of CMK-5. A grafting density of approximately 0.9-1.5 micromol/m(2) was achieved under current research.     

Adsorption of U(VI) from aqueous solution by sulfonated ordered mesoporous carbon

The sulfonated mesoporous carbon (CMK-3-SO₃H) prepared by functionalizing mesoporous carbon (CMK-3) via vapor transfer method has been explored for the removal and recovery of uranium from aqueous solutions. The influences of different experimental parameters such as solution pH, initial concentration, contact time and temperature on adsorption were investigated. The results showed that CMK-3-SO₃H has the highest uranium sorption capacity at initial pH of 5.0 and contact time of 120 min, and the adsorption process could be better described by the pseudo-second-order model and Langmuir isotherm. Selective adsorption studies showed that the CMK-3-SO₃H could selectively remove of U(VI), and the selectivity coefficients of mesoporous carbon in the presence of co-existing ions, Mg(II), Zn(II), Mn(II), Cu(II), Ni(II), Sr(II) and Hg(II) improved after functionalization.     

超声辅助浸渍法制备高分散Pt/CMK-3-US加氢脱萘催化剂

以CMK-3介孔碳作为载体,分别采用传统浸渍法、超声辅助浸渍法、载体硝酸处理法和表面活性剂辅助浸渍法备了Pt/CMK-3、Pt/CMK-3-US、Pt/CMK-3-HNO₃和Pt/CMK-3-CTAB催化剂,并通过表征和催化性能评价进行研究。表征方法包括XRD、BET、SEM、TEM和H₂-TPR,结果表明Pt/CMK-3中Pt分散性最差,Pt/CMK-3-HNO₃和Pt/CMK-3-CTAB中Pt的分散度较好,但是HNO₃对介孔碳的孔道结构有破坏作用,且Pt/CMK-3-HNO₃和Pt/CMK-3-CTAB中的介孔碳的表面性质具有明显变化,只有超声法可以在很好地保持CMK-3的孔道结构和表面性质的基础上提高铂的分散度,Pt的粒径在3 nm左右。萘加氢催化性能评价结果表明Pt/CMK-3-US的催化加氢活性及产物选择性高于Pt/CMK-3,且明显高于Pt/CMK-3-HNO₃和Pt/CMK-3-CTAB。萘转化率可以达到98%以上,十氢萘选择性可以达到95%以上。     

超声辅助浸渍法制备高分散Pt/CMK-3-US加氢脱萘催化剂

以CMK-3介孔碳作为载体,分别采用传统浸渍法、超声辅助浸渍法、载体硝酸处理法和表面活性剂辅助浸渍法备了Pt/CMK-3、Pt/CMK-3-US、Pt/CMK-3-HNO_3和Pt/CMK-3-CTAB催化剂,并通过表征和催化性能评价进行研究。表征方法包括XRD、BET、SEM、TEM和H2-TPR,结果表明Pt/CMK-3中Pt分散性最差,Pt/CMK-3-HNO_3和Pt/CMK-3-CTAB中Pt的分散度较好,但是HNO_3对介孔碳的孔道结构有破坏作用,且Pt/CMK-3-HNO_3和Pt/CMK-3-CTAB中的介孔碳的表面性质具有明显变化,只有超声法可以在很好地保持CMK-3的孔道结构和表面性质的基础上提高铂的分散度,Pt的粒径在3 nm左右。萘加氢催化性能评价结果表明Pt/CMK-3-US的催化加氢活性及产物选择性高于Pt/CMK-3,且明显高于Pt/CMK-3-HNO_3和Pt/CMK-3-CTAB。萘转化率可以达到98%以上,十氢萘选择性可以达到95%以上。     

Thermal stability of high surface area silicon carbide materials

The synthesis of mesoporous silicon carbide by chemical vapor infiltration of dimethyl dichlorosilane into mesoporous silica SBA-15 and subsequent dissolution of the silica matrix with HF was investigated. The influence of the synthesis parameters of the composite material (SiC/SBA-15) on the final product (mesoporous SiC) was determined. Depending on the preparation conditions, materials with specific surface areas from 410 to 830 m² g⁻¹ and pore sizes between 2 and 10 nm with high mesopore volume (0.31-0.96 cm³ g⁻¹) were prepared. Additionally, the thermal stability of mesoporous silicon carbide at 1573 K in an inert atmosphere (argon) was investigated, and compared to that of SBA-15 and ordered mesoporous carbon (CMK-1). Mesoporous SiC has a much higher thermal textural stability as compared to SBA-15, but a lower stability than ordered mesoporous carbon CMK-1.