The tribological characteristics of TiCN coating at elevated temperatures

The tribological behaviour of TiCN coating prepared by unbalanced magnetron sputtering is studied in this work. The substrates made from austenitic steel were coated by TiCN coatings during one deposition. The measurements were provided by high temperature tribometer (pin-on-disc, CSM Instruments) allowing measuring the dependency of friction coefficient on cycles (sliding distance) up to 500 °C. The evolution of the friction coefficient with the cycles was measured under different conditions, such as temperature or sliding speed and the wear rate of the ball and coating were evaluated. The 100Cr6 balls and the Si₃N₄ ceramic balls were used as counter-parts. The former were used at temperatures up to 200 °C, the latter up to 500 °C. The wear tracks were examined by optical methods and SEM. The surface oxidation at elevated temperatures and profile elements composition of the wear track were also measured.The experiments have shown considerable dependency of TiCN tribological parameters on temperature. Rise in temperature increased both friction coefficient and the wear rate of the coating in case of 100Cr6 balls. The main wear mechanism was a mild wear at temperatures up to 200 °C; fracture and delamination were dominating wear mechanisms at temperatures from 300 to 500 °C.     

Mechanical and tribological behavior of W/WCN bilayers grown by pulsed vacuum arc discharge

This study investigates W/WCN coatings grown by means of a repetitive pulsed vacuum arc discharge while varying the substrate temperature from room temperature (RT) to 200 °C. The coatings were grown using a cathode with W (6N) and WC (6N) targets for the W and WCN layers, respectively, and an anode that contains stainless-steel 304 as a substrate. The films grown at RT and at 150 °C possessed a lower percentage of carbon obtained from energy dispersive spectroscopy. This characteristic was related to the hardness, the coefficient of friction and the adherence. These films also possessed the best mechanical and tribological properties. Several wear mechanisms were identified, such as delamination and plowing out of abrasive and adhesive particles.     

Tribological properties of nanostructured DLC coatings deposited by C60 ion beam

The frictional and wear characteristics of nanostructured DLC films were investigated. The coatings were deposited on silicon substrates by irradiation of a mass-separated C₆₀ ion beam with 5 keV of energy and a deposition temperature ranging from 100 to 450 °C. The effects of deposition temperature on the surface morphology, nano-structure, mechanical properties and tribological characteristics of the coatings were assessed. Results showed that deposition temperature strongly affects the nanostructure and surface morphology of the coatings. Coatings deposited at temperatures exceeding 350–400 °C exhibited an increase in surface roughness as well as compressive stress due to the formation of graphite, which led to a significant increase in the friction coefficient and wear rate. Coatings deposited at 300 °C showed the best tribological properties.     

RSM base study of the effect of deposition temperature and hydrogen flow on the wear behavior of DLC films

A statistical study of the effects of deposition temperature and hydrogen flow on the wear behavior of DLC films was examined using the RSM method based on a central composite design. DLC films were deposited on the nitrocarburized AISI 4140 steel by the pulsed DC PACVD method at temperature range of 60–120 °C and in an atmosphere of hydrogen range of 0–40 sccm. Results indicated that a combination of relatively high deposition temperature and low hydrogen flow or low deposition temperature and high hydrogen flow produce DLC film with low wear rate and low friction coefficient.     

Effect of surface laser texture on friction properties of nickel-based composite

Laser surface texturing (LST) was performed on the nickel-based composites by a Nd:YAG pulsed laser and the regular-arranged dimples with diameter of 150 μm were fabricated on their surfaces. The textured surfaces were smeared with molybdenum disulfide powder. The tribological properties of the textured and filled composites were investigated by carrying out sliding wear tests against an alumina ball as a counterface using a high temperature ball-on-disk tribometer. The tests were conducted at a sliding speed of 0.4 m/s and at normal loads ranging from 20–100 N and from room temperature to 600 °C. The friction coefficient of nickel-based composite textured and smeared with molybdenum disulfide was found to reduce from 0.18 to 0.1 at the temperature range from 200 to 400 °C. The texture with a dimple density of 7.1% was observed to prolong wear life of MoS2 film by more than four times in comparison to the texture with other dimple densities. The lubricious oxide particles stored in the dimples reduce friction coefficient at elevated temperatures and compensate for the extra lubricant owing to the degradation of MoS₂ caused by its oxidation at high temperatures.     

Mechanical and unlubricated tribological properties of titanium-containing diamond-like carbon coatings

Titanium-containing diamond-like carbon (Ti-DLC) coatings were deposited on steel with a close-field unbalanced magnetron sputtering in a mixed argon/acetylene atmosphere. The morphology and structure of Ti-DLC coatings were investigated by scanning electron microscopy, transmission electron microscopy, atomic force microscopy and Raman spectroscopy. Nanoindentation, nanoscratch and unlubricated wear tests were carried out to evaluate the hardness, adhesive and tribological properties of Ti-DLC coatings. Electron microscopic observations demonstrated the presence of titanium-rich nanoscale regions surrounded by amorphous carbon structures in Ti-DLC coating. The Ti-DLC coatings exhibit friction coefficients of 0.12–0.25 and wear rates of 1.82 × 10^?9 to 4.29 × 10^?8 mm³/Nm, depending on the counterfaces, sliding speed and temperature. The Ti-DLC/alumina tribo-pair shows a lower friction coefficient than the Ti-DLC/steel tribo-pair under the identical wear conditions. Increasing the test temperature from room temperature to 200 °C reduces the coefficient of friction and, however, clearly increases the wear rate of Ti-DLC coatings. Different wear mechanisms, such as surface polishing, delamination and tribo-chemical reactions, were found in the tribo-contact areas, depending on different wear conditions.     

Tribological properties of NiCr–Al2O3 cermet-based composites with addition of multiple-lubricants at elevated temperatures

The tribological properties of NiCr-40 wt% Al₂O₃ (NC40A) cermet-based composites containing SrSO₄ and other lubricant (graphite, MoS₂ and Ag) against alumina ball were evaluated to identify their self-lubrication mechanisms from room temperature to 800 °C. The composites demonstrated distinct improvements in effectively reducing friction and wear, as compared to NC40A cermet. The best results were observed for NC40A–10SrSO₄–10Ag composite, which exhibited satisfactory reproducibility of friction coefficient over a wide temperature range (200–800 °C) through high temperature cyclic friction tests due to the formation of synergistic lubricating films SrAl₄O₇, NiCr₂O₄ and Ag on the contact surface.     

Tribological behavior of NiAl matrix composites with addition of oxides at high temperatures

NiAl, NiAl–Cr–Mo alloy and NiAl matrix composites with addition of oxides (ZnO/CuO) were fabricated by powder metallurgy route. It was found that some new phases (such as NiZn₃, Cu_0.81Ni_0.19 and Al₂O₃) are formed during the fabrication process due to a high-temperature solid state reaction. Tribological behavior was studied from room temperature to 1000 °C on an HT-1000 ball-on-disk high temperature tribometer. The results indicated that NiAl had high friction coefficient and wear rate at elevated temperatures, while incorporation of Cr(Mo) not only enhanced mechanical properties evidently but also improved high temperature tribological properties. Among the sintered materials, NiAl matrix composite with addition of ZnO showed the lowest wear rate at 1000 °C, while CuO addition into NiAl matrix composite exhibited the self-lubricating performance and the best tribological properties at 800 °C.     

Mechanical and tribological properties of NiCr–Al2O3 composites at elevated temperatures

The effect of Al₂O₃ content on the mechanical and tribological properties of Ni–Cr alloy was investigated from room temperature to 1000 °C. The results indicated that NiCr–40 wt% Al₂O₃ composite exhibited good wear resistance and its compressive strength remained 540 MPa even at 1000 °C. The values obtained for flexural strength and fracture toughness at room temperature were 771 MPa, 15.2 MPa m^1/2, respectively. Between 800 °C and 1000 °C, the adhesive and plastic oxide layer on the worn surface of the composite was claimed to be responsible for low friction coefficient and wear rate.     

Tribology of ultra-high molecular weight polyethylene disks molded at different temperatures

Tribological characteristics of ultra-high molecular weight polyethylene (UHMW-PE) disks molded at 130–190 °C were studied. The highest crystallinity was obtained for the sheet molded at 130 °C, but crystallinity decreased with increasing molding temperature. Beyond 150 °C, the resultant crystallinity reached a constant level. The dynamic friction coefficients of these UHMW-PE disks were measured using a ball-on-disk friction tester. The friction coefficient decreased with increasing number of rotations in the early stage of the measurement, and achieved at an equilibrium level, independent of the molding temperature. The steady-state friction coefficient was 0.04 for the disk molded at 130 °C and increased with increasing molding temperature. The disks molded at 150–190 °C always had a steady-state friction coefficient of 0.065. The surface deformation of each disk was evaluated from the observation of the resultant wear track. Analyzing the relationship between the above friction coefficient and width of the wear track enabled us to interpret the tribological mechanism generated in this study.     

Mechanical and tribological properties of sputtered Mo–Se–C coatings

Transition metal dichalcogenides belong to the more developed class of materials for solid lubrication. However, the main limitation of these materials is the detrimental effect of air humidity causing an increase in the friction. In previous works, molybdenum diselenide has been shown to be a promising coating retaining low friction even in very humid environment. In this study, Mo–Se–C films were deposited by sputtering from a C target with pellets of MoSe₂. Besides the evaluation of the chemical composition, the structure, the morphology, the hardness and the cohesion/adhesion, special attention was paid to the tribological characterization.The C content varied from 29 to 68 at.% which led to a progressive increase of the Se/Mo ratio. As a typical trend, the hardness increases with increasing C content. The coatings were tested at room temperature with different air humidity levels and at temperatures up to 500 °C on a pin-on-disc tribometer. The friction coefficient of Mo–Se–C coatings increased with air humidity from ～0.04 to ～0.12, while it was as low as 0.02 at temperature range 100–250 °C. The coatings were very sensitive to the elevated temperature being worn out at 300 °C due to adhesion problems at coating–titanium interface.     

Tribological behavior of graphite-containing nickel-based composite as function of temperature,load and counterface

Nickel-based graphite-containing composites were prepared by powder metallurgy method. Their mechanical properties at room temperature and friction and wear properties from room temperature to 600 °C were investigated by a pin-on-disk tribometer with alumina, silicon nitride and nickel-based alloy as counterfaces. The effects of graphite addition amount, temperature, load, sliding speed and counterface materials on the tribological properties were discussed. The micro-structure and worn surface morphologies were analyzed by scanning electron microscope (SEM) attached with energy dispersive spectroscopy (EDS). The results show that the composites are mainly consisted of nickel-based solid solution, free graphite and carbide formed during hot pressing. The friction and wear properties of composites are all improved by adding 6–12 wt.% graphite while the anti-bending and tensile strength as well as hardness decrease after adding graphite. The friction coefficients from room temperature to 600 °C decrease with the increase of load, sliding speed while the wear rates increase with the increasing temperature, sliding speed. The lower friction coefficients and wear rates are obtained when the composite rubs against nickel-based alloy containing molybdenum disulfide. Friction coefficients of graphite-containing composites from room temperature to 600 °C are about 0.4 while wear rates are in the magnitude of 10^?5 mm³/(N m). At high temperature, the graphite is not effective in lubrication due to the oxidation and the shield of ‘glaze’ layer formed by compacting back-transferred wear particles. EDS analysis of worn surface shows that the oxides of nickel and molybdenum play the main role of lubrication instead of graphite at the temperature above 400 °C.     

Tribological properties of Ni-17.5Si-29.3Cr alloy at room and elevated temperatures

The tribological properties of Ni-17.5Si-29.3Cr alloy against Si₃N₄ were studied on a ball-on-disc tribotester between room temperature and 1000 °C. The effects of temperature on the tribological properties of the alloy were investigated. The worn surfaces of the alloy were examined using scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The results indicated that the tribological behavior of the alloy expressed some differences with increase in testing temperature. At low and moderate temperatures (below 800 °C), the alloy showed excellent wear and oxidation resistances, and the wear rate of the alloy remained in the magnitude of 10^?5 mm³/Nm; but at elevated temperature (800–1000 °C), the wear and oxidation resistances decreased, and the wear rate of the alloy increased up to 10^?4 mm³/Nm. The friction coefficient decreased from 0.58 to 0.46 with the rising of testing temperature from 20 to 600 °C, and then remained nearly constant. The wear mechanism of the alloy was mainly fracture and delamination at low and moderate temperatures, and transformed to adhesive and oxidation at elevated temperatures.     

Development of a simple ‘temperature versus sliding speed’ wear map for the sliding wear behaviour of dissimilar metallic interfaces

The variation in wear behaviour during limited debris retention sliding wear of Nimonic 80A versus Stellite 6 (counterface) between room temperature and 750 °C, at sliding speeds of 0.314, 0.654 and 0.905 m s⁻¹, was investigated. At 0.314 m s⁻¹, mild oxidational wear was observed at all temperatures, due to transfer and oxidation of Stellite 6-sourced debris to the Nimonic 80A and resultant separation of the Nimonic 80A and Stellite 6 wear surfaces. Between room temperature and 450 °C, this debris mostly remained in the form of loose particles (with only limited compaction), whilst between 510 and 750 °C, the particles were compacted and sintered together to form a wear protective ‘glaze’ layer.At 0.654 and 0.905 m s⁻¹, mild oxidational wear due to transfer and oxidation of Stellite 6-sourced debris was only observed at room temperature and 270 °C (also 390 °C at 0.654 m s⁻¹). At 390 °C (450 °C at 0.654 m s⁻¹) and above, this oxide was completely absent and ‘metal-to-metal’ contact resulted in an intermediate temperature severe wear regime—losses in the form of ejected metallic debris were sourced almost completely from the Nimonic 80A. Oxide debris, this time sourced from the Nimonic 80A sample, did not reappear until 570 °C (630 °C at 0.654 m s⁻¹), however, were insufficient to eliminate completely severe wear until 690 and 750 °C. At both 0.654 and 0.905 m s⁻¹, the oxide now preventing severe wear at 690 and 750 °C tended not to form ‘glaze’ layers on the surface of the Nimonic 80A and instead supported continued high wear by abrasion. This abrasive action was attributed to the poor sintering characteristics of the Nimonic 80A-sourced oxide, in combination with the oxides’ increased mobility and decreased residency.The collected data were used to compose a simple wear map detailing the effects of sliding speed and temperature on the wear of Nimonic 80A slid against Stellite 6, at these speeds and temperatures of between room temperature and 750 °C.     

Tribological property of self-lubricating PM304 composite

PM304 composite has been prepared by high-energy ball milling and powder metallurgy. The composition of the PM304 composite is the same as that of PS304, but the microstructure is quite different. The microstructure of PM304 composite was fine and dense, the size of self-lubricating particles in the composite was very small. The tribological properties of PM304 composites against Inconel X-750 were examined in the temperature range from room temperature to 800 °C. The friction coefficient of PM304 was ranged from 0.32 to 0.41. At room temperature, brittle fracture occurred on the worn surface. With the increase of temperature up to 200 °C, a protective layer consisting of fluorides and Ag existed on the worn surface and led to a low wear rate. The wear resistance of the PM304 was superior to that of the PS304 in the temperature range from room temperature to 650 °C. The improvement in wear resistance of the PM304 was discussed in the terms of its microstructural characteristics.     

Tribological characterisation of siliconcarbonitride ceramics derived from preceramic polymers

Amorphous SiCN ceramics were prepared in a laboratory scale as disk shaped specimens with 10 mm diameter and 0.3 mm thickness. The friction and wear behaviour was characterised in gross slip fretting tests under unlubricated conditions at room temperature against steel (100Cr6) and ceramic (Al₂O₃). Tests with a ball-on-disk contact were performed in laboratory air with different content of water vapour. The results show clearly that the relative humidity has a significant effect on friction and wear behaviour. All tests in dry air lead to higher friction and higher wear rate than in normal air. Improved friction and wear behaviour was observed with increasing pyrolysis temperature up to 1100 °C of the SiCN specimens. This is attributed to increasingly better mechanical properties and higher stiffness of the amorphous network due to the evaporation of gaseous organic species and the formation of free graphite like carbon.     

Characteristics of oxidative wear and oxidative mildwear

Dry sliding tests were performed for 45, 4Cr5MoSiV1 steels and 3Cr3Mo2V cast steel at 200 and 400 °C. The wears at 200 and 400 °C are of oxidative wear characteristic due to tribo-oxides formed on worn surfaces. However, the wear at 200 °C presents different wear behaviors and characteristics from the one at 400 °C. The wear at 200 °C is a typical oxidative mild wear, but the wear at 400 °C is beyond oxidative mild wear, here called oxidative wear. The characteristics of oxidative mild wear and oxidative wear were clarified.     

Tribo-layer and its role in dry sliding wear of Ti–6Al–4V alloy

Dry sliding wear tests were performed for Ti–6Al–4V alloy under a load of 50–250 N at 25–500 °C on a pin-on-disk elevated temperature tester. Worn surfaces and subsurfaces were thoroughly investigated for the morphology, composition and structure of tribo-layers. Ti–6Al–4V alloy could not be considered to possess poor wear resistance at all times, and presented a substantially higher wear resistance at 400–500 °C than at 25–200 °C. The tribo-layer, a mechanical mixing layer, was noticed to exist on worn surfaces under various conditions. High wear rate at 25–200 °C was ascribed to no protective tribo-layer containing no or trace tribo-oxides. As more oxides appeared in the tribo-layers, they presented an obviously protective role due to their high hardness, thus giving a reasonable explanation for high wear resistance of Ti–6Al–4V alloy at 400–500 °C.     

A comparison of boundary wear film formation on steel and a thermal sprayed Co/Cr/Mo coating under sliding conditions

In this paper, the action of the zinc dialkyl dithiophosphate (ZDDP) anti-wear additive has been examined on two different materials (Steel AISI 52100 and a Co/Cr/Mo thermal spray coating) sliding against cast iron in reciprocating mode. Tests have been conducted under lubricated wear conditions at relatively low (20, 50 °C) and elevated (up to 100 °C) bulk oil temperatures. A comparison is made between the friction, wear and chemical nature of the wear film formed under varying temperatures, on two materials, in two lubricants (one free from and one containing ZDDP) and after different test durations. The wear film has been examined by energy dispersive X-ray analysis (EDAX) and X-ray photoelectron spectroscopy (XPS).In this work, it has been shown in this work that the friction coefficient is dependent on the temperature, the lubricant and the nature of the contacting surfaces. In the presence of ZDDP, a wear film, comprising Zn, S and P, forms even at the lowest bulk oil temperature of 20 °C. The nature of the film is dependent on the substrate material and the steel and Co/Cr/Mo coating showed contrasting film characteristics. In this paper, the wear and friction results for each couple in oil containing and free from additives is discussed with reference to the nature of the wear film. A correlation has been made between the wear, friction and chemical analysis measurements.     

Characterization and tribological investigation of sol–gel ceramic films on Ti–6Al–4V

SiO₂, TiO₂, and hydroxyapatite (HA) thin films with good biocompatibility were grown on Ti–6Al–4V (coded as TC4) substrate by sol–gel and dip-coating processes from specially formulated sols, followed by annealing at 500 °C The chemical states of some typical elements in the target films were detected by means of X-ray photoelectron spectroscopy (XPS). Atomic force microscopy (AFM) and high-resolution scanning electron microscopy (SEM) are applied to characterize the original unworn films. The tribological properties of thin films sliding against an AISI52100 steel ball were evaluated on a reciprocating friction and wear tester. As the result, the target films composed of nano-particles ranging from 30 nm to 100 nm around were obtained. All the sol–gel ceramic films are superior in resisting wear compared with the TC4 substrate. Among all, HA film shows the best resistance while SiO₂ film shows the worst wear resistance both under higher (3 N) and lower load (1 N). TiO₂ shows good wear resistance under lower load (1 N). SEM observation of the morphologies of worn surfaces indicates that the wear of TC4 is characteristic of abrasive wear. Differently, abrasion, plastic deformation and micro-fracture dominate the wear of ceramic films. The superior friction reduction and wear resistance of HA film is greatly due to the slight plastic deformation of the film. It is supposed that the deformation of the HA film is closely related to the special arrangement of the nano-particles and microstructure. HA film is recommended for clinical application from the point of wear resistance view.