2个含呫吨结构双酚化合物的合成

以呫吨酮为原料,经二氯亚砜氯化得到9,9-二氯呫吨中间体,无需分离纯化,将其分别与邻甲酚和2,6-二甲基苯酚进行取代反应,制得2个含呫吨结构的双酚化合物9,9-二(4-羟基-3-甲基苯基)呫吨和9,9-二(4-羟基-3,5-二甲基苯基) 呫吨,产率分别为81.0%和80.5%。 用FTIR、1H NMR、13C NMR和元素分析对其组成和结构进行了表征。 该法具有操作简单、反应条件温和及收率高等优点。     

9, 9-二(3-氨基-4-羟基苯基)呫吨的合成

以醋酸酐为溶剂, 将9, 9-二(4-羟基苯基)呫吨与浓硝酸在15 ℃左右发生硝化反应1.5 h, 形成中间体-9, 9-二(3-硝基-4-羟基苯基)呫吨, 产率为88.5%;继而以Pd/C 为催化剂, 80%的水合肼为还原剂, 在乙醇和1, 4-二氧六环混合溶剂中, 于70 ℃将中间体进行还原反应10 h, 得到目标产物9, 9-二(3-氨基-4-羟基苯基)呫吨, 产率为90.8%, 两步反应总收率为80.4%。 中间体与目标化合物经NMR、FTIR和元素分析等确定了它们的结构。     

一种含三氟甲基和呫吨结构聚酰胺的合成与性能

在浓硫酸和3-巯基丙酸催化下,3′-三氟甲基苯基-2,2,2-三氟苯乙酮(1)和甲苯于40～50℃下缩合反应8 h,制得中间体-1,1-二(4-甲基苯基)-1-(3′-三氟甲基苯基)-2,2,2-三氟甲基乙烷(2),继而在光照和N-溴代丁二酰亚胺促进下,将中间体氧化得到二羧酸-1,1-二(4-羧基苯基)-1-(3′-三氟甲基苯基)-2,2,2-三氟甲基乙烷(3),二步反应总收率为77.4%.采用Yamazaki体系,3和9,9-二[(4-氨基苯氧基)苯基]呫吨进行溶液亲核缩聚反应,制得了一种高分子量的(数均分子量为43000,分子量分布为1.8)新型含三氟甲基和呫吨结构的聚酰胺.该聚酰胺为非晶态结构并具有良好的透光率(λcutoff=330 nm),其玻璃化转变温度(Tg)为242℃,在氮气气氛中5%的热失重温度(Td5)为465℃,800℃时的残炭率为50%.聚合物易溶于N,N-二甲基乙酰胺(DMAc)、N-甲基吡咯烷酮(NMP)、间甲酚、吡啶(Py)和四氢呋喃(THF)等有机溶剂中,并可浇注得到韧性好和透明的薄膜,其拉伸强度为85 MPa,拉伸模量为2.0 GPa,断裂伸长率为10%.同时,该聚合物的体积电阻、表面电阻和介电常数分别为2.85×1015Ωcm,4.23×1014Ω和3.55(100 Hz),呈现了良好的电绝缘性能.     

4,4′-二（4-氯甲酰苯氧基）二苯砜的合成

以DMF作溶剂,在四丁基氟化铵 （TBAF）存在下,对甲基苯基三甲硅基醚（1）和4,4＇-二氯二苯砜（2）于100 ℃反应1 h,合成了4,4＇-二（4-甲基苯氧基）二苯砜（3）,产率为92%;加入催化量的N-溴代丁二酰亚胺（NBS）并在光照条件下,与氧气反应得到中间体-4,4＇-二（4-羧基苯氧基）二苯砜（4）,其产率达90%;将化合物4与二氯亚砜反应合成目标产物4,4＇-二（4-氯甲酰基苯氧基）二苯砜（5）,总收率为74.5%（以对甲基苯基三甲硅基醚为基准计算）.     

一种可溶性含呫吨结构的聚醚醚酮酮的合成与表征

以呫吨酮为起始原料,经二氯亚砜作用得到9,9-二氯呫吨中间体,继而与苯酚发生取代反应,探索了"一锅、二步"法制备含呫吨结构的双酚单体———9,9-二(4-羟基苯基)呫吨(BHPX)的新方法.在氮气保护下,在K2CO3存在下,以环丁砜为溶剂,将其与1,3-二(4-氟苯甲酰基)苯进行亲核缩聚反应,制得了一种高分子量的(数均分子量为45000,多分散性指数为1.9)新型含呫吨结构的Cardo型聚醚醚酮酮(PEEKK-X),并用FTIR,DSC,TG及WAXD等方法对其进行了分析表征.结果表明,所制得的聚合物(PEEKK-X)为无定形结构,其玻璃化转变温度(Tg)为215℃;在氮气气氛中5%的热失重温度(Td)为558℃,700℃时的残炭率为67%;在常温下易溶于非质子极性溶剂(如NMP、DMF和DMAc)和极性较弱的溶剂如CHCl3中.该聚合物可通过溶液浇铸成膜,所得到的薄膜韧性好,透明且耐折,其拉伸强度为81.5 MPa,杨氏膜量为2.48 GPa,断裂伸长率为16.8%.     

3,3-二{2,2-二[4-(N,N-二取代氨基)苯基]乙烯基}-4,5,6,7-四氯-2-苯并[c]呋喃酮的合成

在对甲苯磷酸存在下,采用1,1-二[4-(N,N-二取代氨基)苯基]乙烯(3)和四氯苯酐在乙酸酐溶液中的缩合反应合成了3,3-二{2,2-二[4-(N,N-二取代氨基)苯基]乙烯基}-4,5,6,7-四氯-2-苯并[c]呋喃酮(4),产率89～93％。3由4,4＇-二(N,N-二取代氨基)二苯甲酮(1)与甲基碘化镁进行Grignard反应的产物经水解再脱水制得,产率85％～88.5％(以1为基准)。     

可光固化单体2,7-二溴-9,9-双[4’-(3″-乙基-3″-氧杂环丁烷甲氧基己基氧基)苯基]芴的合成

以芴为原料,经溴代和氧化反应制得2,7-二溴芴酮(3);3与苯酚反应合成2,7-二溴-9,9-双(4’-羟基苯基)芴(4);4与3-(6’-溴己氧基甲基)-3-乙基氧杂环丁烷经醚化反应合成了可光固化单体2,7-二溴-9,9-双[4’-(3″-乙基-3″-氧杂环丁烷甲氧基己基氧基)苯基]芴,总收率67%,其结构经1H NMR,13C NMR和元素分析表征。     

一种含三氟甲基和咕吨结构聚酰胺的合成与性能

在浓硫酸和3-巯基丙酸催化下,3'-三氟甲基苯基-2,2,2-三氟苯乙酮(1)和甲苯于40～50℃下缩合反应8 h,制得中间体-1,1-二(4-甲基苯基)-1-(3'-三氟甲基苯基)-2,2,2-三氟甲基乙烷(2),继而在光照和N-溴代丁二酰亚胺促进下,将中间体氧化得到二羧酸-1,1-二(4-羧基苯基)-1-(3'-三...     

1-(3,5-二甲基苯基)-1-[(1S,4S)-1,7,7-三甲基双环[2.2.1]庚烷-2-基]肼的合成工艺改进

以3,5-二甲基苯胺和2-莰酮为起始原料,在微波促进下,经缩合反应制得N-(3,5-二甲基苯基)-1-(1S,4S)-1,7,7-三甲基二环[2.2.1]庚烷-2-亚胺(1);1经硼氢化钠还原后再与羟胺-O-磺酸经胺化反应合成了1-(3,5-二甲基苯基)-1-[(1S,4S)-1,7,7-三甲基双环[2.2.1]庚烷-2-基]肼,总收率70.4%,其结构经1H NMR和ESI-MS确证。     

(E)-2-[2-(6-氯嘧啶-4-基氧基)苯基]-3-甲氧基丙烯酸甲酯的合成工艺改进

以3-(α-甲氧基)亚甲基苯并呋喃-2-(3H)-酮为原料,经3步反应合成了杀菌剂嘧菌酯的重要中间体——(E)-2-[2-(6-氯嘧啶-4-基氧基)苯基]-3-甲氧基丙烯酸甲酯(4),总收率61%。4的结构经NMR表征。     

New Organosoluble and Optically Transparent Polyamides Containing Xanthene Units and Methyl Pendant Groups From 9,9-Bis[4-(4-carboxyphenoxy)-3-methylphenyl]xanthene

A new aromatic dicarboxylic acid, 9,9-bis[4-(4-carboxyphenoxy)-3-methylphenyl]xanthene (BCAMPX) was prepared from the nucleophilic substitution reaction of 9,9-bis(4-hydroxy-3-methylphenyl)xanthene with p-fluorobenzonitrile, followed by alkaline hydrolysis. Then BCAMPX was polycondensated with various aromatic diamines to afford the polyamides with the number-average molecular weight in the range of 45,300–51,500 and the polydispersity index ranged from 1.67 to 1.85. These polyamides showed glass transition temperatures between 260–286°C and 10% weight loss temperatures ranging from 490 to 504°C and 480 to 490°C in nitrogen and air respectively, and char yields above 52% at 800°C in nitrogen. Nearly all polyamides were readily soluble polar aprotic solvents such as N-methyl-2-pyrrolidone, N,N-dimethylacetamide (DMAc), tetrahydrofuran and pyridine, and afforded transparent, strong and flexible films upon casting from DMAc solvent. All polyamides were amorphous and exhibited tensile strengths of 80–91 MPa, elongations at break of 9–13%, and initial moduli of 1.95–2.82 GPa, as well as low moisture absorption in the range of 2.65–3.65%, and high transparency with an ultraviolet–visible absorption cut-off wavelength in the 360–378 nm range.     

Synthesis and Characterization of New Soluble Polyamides from 9,9-Bis[4-(chloroformylphenoxy)phenyl]xanthene and Various Aromatic Diamines

9,9‐Bis(4‐hydroxyphenyl)xanthene (BHPX) was synthesized in 82% yield from xanthenone in a one‐pot, two‐step synthetic procedure. A new diacyl chloride monomer, 9,9‐bis[4‐(chloroformylphenoxy)phenyl]xanthene (BCPX), was synthesized in three steps from the nucleophilic fluorodisplacement of 4‐fluorobenzonitrile with the dipotassium bisphenolate of BHPX, followed by alkaline hydrolysis of the intermediate bis(ether nitrile), and then chlorination with thionyl chloride. Several novel aromatic polyamides containing ether and bulky xanthene groups with the inherent viscosities (0.72–0.98 dL/g) were prepared by the low temperature polycondensation of BCPX with various aromatic diamines in N,N‐dimethylacetamide (DMAc) solution containing pyridine (Py). All new polyamides were amorphous and readily soluble in various polar solvents such as DMAc, N,N‐dimethylformamide (DMF), N‐methyl‐2‐pyrrolidone (NMP) and Py. These polymers showed relatively high glass transition temperatures between 236 and 298°C, decomposition temperatures at 10% weight loss ranging from 490 to 535°C and 483 to 515°C in nitrogen and air, respectively, and char yields at 700°C in nitrogen higher than 50%. Transparent, flexible, and tough films of these polymers cast from DMAc solutions exhibited tensile strengths ranging from 82 to 106 MPa, elongations at break from 10% to 25%, and initial moduli from 2.0 to 2.8 GPa.     

A new fluorinated poly(ether amide) bearing xanthene group

<正>A new fluorinated poly(ether amide) bearing xanthene group was prepared from 9,9-bis[4-(2-trifluoromethyl-4-aminophenoxy) phenyl]xanthene(BTFAPX) with 9,9-bis[4-(4-carboxyphenoxy)phenyl]xanthene(BCAPX) in the presence of triphenyl phosphate and pyridine(Py).The polymer had the weight-average molecular weight(M_w) of 69,000 and number-average molecular weight(Mn) of 39,000,showed the glass transition temperature(T_g) of 267℃,5%weight loss temperature(T_(d5)) over 460℃both in N_2 and air,and char yield of 62%at 800℃in N_2.This polymer was amorphous and readily soluble in amide-type solvents such as N,N-dimethylacetamide(DMAc),and even in m-cressol,Py and tetrahydrofuran(THF) at room temperature,and exhibited tensile strength of 74 MPa,elongation at break of 6%,tensile moduli of 2.2 GPa.The polymer had low dielectric constant of 3.69(100 Hz), low moisture absorption of 0.56%,and high transparency with an ultraviolet-visible absorption cut-off wavelength at 334 nm.     

New poly(amide-lmide)s syntheses. XV. Preparation and properties of poly(amide-imide)s derived from 9, 9-bis[4-(4-aminophenoxy) phenyl]fluorene and various bis(trimellitimide)s

Fifteen bis(phenoxy) fluorene-containing poly(amide-imide)s III were synthesized by the direct polycondensation of 9,9-bis[4-(4-aminophenoxy)phenyl]fluorene (BAPPF) with var-ious aromatic bis(trimellitimide)s II in N-methyl-2-pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents. Poly(amide-imide)s III having inherent vis-cosities up to 1.45 dL/g were obtained in quantitative yields. Most of the resulting polymers showed an amorphous nature and were readily soluble in polar solvents such as NMP and N,N-dimethylacetamide. All the soluble poly(amide-imide)s afforded transparent, flexible, and tough films. The glass transition temperatures of these polymers were in the range of 263–315°C and the 10% weight loss temperatures were above 510°C in nitrogen. Some properties of poly(amide-imide)s III were compared with those of the corresponding isomeric poly(amide-imide)s III ′ prepared from 9,9-[4-(4-trimellitimidophenoxy)phenyl]fluorene and various aromatic diamines. © 1995 John Wiley & Sons, Inc.     

1-芳基-2-丙酮的合成研究

以芳香胺为原料, 经重氮化和改进的Meerwein芳基取代反应, 合成了一系列的1-芳基-2-丙酮, 其中1-(3,5-二三氟甲基苯基)-2-丙酮是一个新化合物. 改进后的方法简化了合成步骤, 提高了收率, 可方便地用于在苯环上具有不同取代基的芳基丙酮的合成.     

Preparation and properties of polybenzimidazoles containing cardo groups

Several polybenzimidazoles containing cardo groups were prepared: A cardodicarboxylic acid, 9,9-bis(4-carboxyphenyl)fluorene, and two cardotetramines, 9,9-bis(3,4-diaminophenyl)fluorene and 9,9-bis(3,4-diaminophenyl)10-anthrone. The cardodicarboxylic acid was condensed with aromatic tetramines and the cardotetramines were condensed with aromatic dicarboxylic acids. Prior to polymer synthesis two model compounds, 9,9-bis[4,(2-benzimidazolyl)phenyl]fluorene and 2,2′-diphenyl-5,5′-(9,9-fluorenediyl)-bibenzimidazole were prepared and characterized by spectral methods. The polymers were obtained in 60–70% yield and showed reduced viscosity in the range of 0.7–1.1 dL/g. They were soluble in dimethyl formamide (DMF) and chlorinated solvents like tetrachlorethane. The thermal stabilities of these cardopolymers were superior to noncardopoly-benzimidazoles.