Reclamation of wastes contaminated by copper,lead, and zinc

Waste materials containing toxic levels of copper, lead, and zinc, such as mine and smelter wastes, present difficult conditions for the establishment of vegetation. This article reviews the many attempts which have been made to reclaim these wastes. Inert wastes from mining and quarrying operations, such as slate quarry waste and certain colliery shales, seem to be good materials for reclaiming wastes contaminated by copper, lead, and zinc. Organic wastes, such as sewage sludge and domestic refuse, may provide only a temporary visual improvement and stabilization of the toxic materials.Nontolerant plant materials may often be planted directly on modern waste materials, which are less toxic than they were in the past. However, tolerant plant materials are needed for revegetating waste materials produced by early and more primitive extraction methods.     

Chemical immobilization of lead, zinc, and cadmium in smelter-contaminated soils using biosolids and rock phosphate

Chemical immobilization, an in situ remediation method where inexpensive chemicals are used to reduce contaminant solubility in contaminated soil, has gained attention. We investigated the effectiveness of lime-stabilized biosolid (LSB), N-Viro Soil (NV), rock phosphate (RP), and anaerobic biosolid (AB) to reduce extractability and plant and gastrointestinal (GI) bioavailability in three Cd-, Pb-, and Zn-contaminated soils from smelter sites. Treated (100 g kg(-1) soil) and control soils were incubated at 27 degrees C and -0.033 MPa (0.33 bar) water content for 90 d. The effect of soil treatment on metal extractability was evaluated by sequential extraction, on phytoavailability by a lettuce bioassay (Lactuca sativa L.), on human GI availability of Pb from soil ingestion by the Physiologically Based Extraction Test. The largest reductions in metal extractability and phytoavailability were from alkaline organic treatments (LSB and NV). Phytotoxic Zn [1188 mg Zn kg(-1) extracted with 0.5 M Ca(NO3)2] in Blackwell soil (disturbed soil) was reduced by LSB, NV, and RP to 166, 25, and 784 mg Zn kg(-1), respectively. Rock phosphate was the only treatment that reduced GI-available Pb in both gastric and intestinal solutions, 23 and 92%, respectively. Alkaline organic treatments (LSB, NV) decreases Cd transmission through the food chain pathway, whereas rock phosphate decreases risk from exposure to Pb via the soil ingestion pathway. Alkaline organic treatments can reduce human exposure to Cd and Pb by reducing Zn phytotoxicity and revegetation of contaminated sites.     

Biosolid colloid-mediated transport of copper, zinc, and lead in waste-amended soils

Increasing land applications of biosolid wastes as soil amendments have raised concerns about potential toxic effects of associated metals on the environment. This study investigated the ability of biosolid colloids to transport metals associated with organic waste amendments through subsurface soil environments with leaching experiments involving undisturbed soil monoliths. Biosolid colloids were fractionated from a lime-stabilized, an aerobically digested, and a poultry manure organic waste and applied onto the monoliths at a rate of 0.7 cm/h. Eluents were monitored for Cu, Zn, Pb, and colloid concentrations over 16 to 24 pore volumes of leaching. Mass-balance calculations indicated significantly higher (up to 77 times) metal elutions in association with the biosolid colloids in both total and soluble fractions over the control treatments. Eluted metal loads varied with metal, colloid, and soil type, following the sequences Zn = Cu > Pb, and ADB > PMB > LSB colloids. Colloid and metal elution was enhanced by decreasing pH and colloid size, and increasing soil macroporosity and organic matter content. Breakthrough curves were mostly irregular, showing several maxima and minima as a result of preferential macropore flow and multiple clogging and flushing cycles. Soil- and colloid-metal sorption affinities were not reliable predictors of metal attenuation/elution loads, underscoring the dynamic nature of transport processes. The findings demonstrate the important role of biosolid colloids as contaminant carriers and the significant risk they pose, if unaccounted, for soil and ground water contamination in areas receiving heavy applications of biosolid waste amendments.     

pH-dependent release of cadmium,copper, and lead from natural and sludge-amended soils

The pH-dependent release of cadmium, copper, and lead from soil materials was studied by use of a stirred flow cell to quantify their release and release rates, and to evaluate the method as a test for the bonding strength and potential mobility of heavy metals in soils. Soil materials from sludge-amended and nonamended A horizons from a Thai coarse-textured Kandiustult and a Danish loamy Hapludalf were characterized and tested. For each soil sample, release experiments with steady state pH values in the range 2.9 to 7.1 and duration of 7 d were performed. The effluent was continuously collected and analyzed. Release rates and total releases were higher for the Hapludalf than the Kandiustult and higher for the sludge-amended soils than the nonamended soils. With two exceptions the relative release rates (release rate/total content of metal in soil) plotted vs. steady state pH followed the same curves for each metal, indicating similar bonding strengths. These curves could be described by a rate expression of the form: relative release rate = k[H+]a, with specific a (empirical constant) and k (rate constant) parameters for each metal demonstrating that metal release in these systems can be explained by proton-induced desorption and dissolution reactions. With decreasing pH, pronounced increases in release rates were observed in the sequence cadmium > lead > copper, which express the order of metal lability in the soils. The flow cell system is useful for comparison of metal releases as a function of soil properties, and can be used as a test to rank soils with respect to heavy metal leaching.     

Availability of arsenic, copper, lead, thallium, and zinc to various vegetables grown in slag-contaminated soils

To anticipate a possible hazard resulting from the plant uptake of metals from slag-contaminated soils, it is useful to study whether vegetables exist that are able to mobilize a given metal in the slag to a larger proportion than in an uncontaminated control soil. For this purpose, we studied the soil to plant transfer of arsenic, copper, lead, thallium, and zinc by the vegetables bean (Phaseolus vulgaris L. 'dwarf bean Modus'), kohlrabi (Brassica oleracea var. gongylodes L.), mangold (Beta vulgaris var. macrorhiza ), lettuce (Lactuca sativa L. 'American gathering brown'), carrot (Daucus carota L. 'Rotin', 'Sperlings's'), and celery [Apium graveiolus var. dulce (Mill.) Pers.] from a control soil (Ap horizon of a Entisol) and from a contaminated soil (1:1 soil-slag mixtures). Two types of slags were used: an iron-rich residue from pyrite (FeS2) roasting and a residue from coal firing. The metal concentrations in the slags, soils, and plants were used to calculate for each metal and soil-slag mixture the plant-soil fractional concentration ratio (CRfractional,slag), that is, the concentration ratio of the metal that results only from the slag in the soil. With the exception of TI, the resulting values obtained for this quantity for As, Cu, Pb, and Zn and for all vegetables were significantly smaller than the corresponding plant-soil concentration ratios (CRcontrol soil) for the uncontaminated soil. The results demonstrate quantitatively that the ability of a plant to accumulate a given metal as observed for a control soil might not exist for a soil-slag mixture, and vice versa.     

Response of soil microbiological activities to cadmium,lead, and zinc salt amendments

Heavy metal pollution of soil has been recognized as a major factor impeding soil microbial processes. From this perspective, we studied responses of the soil biological activities to metal stress simulated by soil amendment with Zn, Pb, and Cd chlorides. The amounts of heavy metal salts added to five metal-polluted soils and four nonpolluted soils were selected to match the total metal concentrations typically found in polluted soils of the Silesia region of Poland. From the perspective of soil quality, metal mobility in amended soils could not be described by simple functions of pH or organic matter. Reaction of Pb with the soil caused strong immobilization with less than 1% of the Pb amendment recovered by 0.01 M CaCl2 extractions. Immobilization of Cd was also significant, whereas immobilization of the Zn amendment was much weaker than that of Cd or Pb. The Zn amendment had substantial inhibitory effect on soil dehydrogenase, acid and alkaline phosphatase, arylsulfatase, urease, and nitrification potential. Generally, Cd and Pb had limited or stimulatory effect on most of these biological activities, with an exception of Pb strongly inhibiting soil urease. The effect of the metal amendments on biological activities could not be satisfactorily accounted for by metal toxicity because no strong relationship was observed between extractable metal content and the degree of inhibition. The Zn amendment had a significant effect on soil pH, resulting in confounding effects of pH and Zn toxicity on activities. Metal amendment experiments seem to be of limited utility for meaningful assessment of metal contamination effects on soil quality.     

Preceding crop affects grain cadmium and zinc of wheat grown in saline soils of central Iran

Enhanced Cd concentrations in wheat (Triticum aestivum L.) grain produced on saline soils of central Iran have been recently reported. Because wheat bread is a major dietary component for the Iranian people, practical approaches to decrease Cd concentration in wheat grain were investigated. This study investigated the influence of sunflower-wheat vs. cotton-wheat rotations on extractable Cd and on Cd uptake by wheat in these salt-affected soils. Two fields with different levels of Cd contamination (1.5 and 3.2 mg total Cd kg(-1) dry soil) were cropped with different rotations (cotton-wheat and sunflower-wheat) in Qom province, central Iran. Seeds of cotton (Gossypium L.) or sunflower (Helianthus annuus L. cv. Record) were planted in plots. After harvesting of the plants and removal of crop residues, wheat (cv. Rushan) was seeded in all plots. For both studied soils, the concentrations of Cd extracted by 0.04 M EDTA and 1 M CaCl(2) were significantly (P < or = 0.05) greater after cotton than after sunflower. Accordingly, the total amount of Cd in sunflower shoot was significantly (P < or = 0.05) greater than in the cotton shoot. Shoot Cd content in wheat plants grown after cotton and sunflower were significantly different; wheat shoots after cotton accumulated more Cd (two to four times) than after sunflower. Wheat grain Cd concentration after sunflower was much lower (more than seven times) than after cotton. The results of this study showed that sunflower in rotation with wheat in salt-affected soils of central Iran significantly reduced the risk of Cd transfer to wheat grain.     

Effect of organic matter oxidation on the fractionation of copper, zinc, lead, and arsenic in sewage sludge and amended soils

Long-term land application of sewage sludge (SS) has caused concern over the potential release of trace metals into the environment following the degradation of organic matter (OM). This study was performed to assess the impact of OM degradation on the relative distribution of Cu, Zn, Pb, and As in SS and SS-amended soils. Three SSs of different ages and two soils treated with SS were subjected to incubation and direct chemical oxidation using diluted HO, followed by a sequential extraction. The majority of Cu, Pb, and As were bound to OM, whereas the majority of Zn was bound with Fe/Mn oxides for all three SSs. Incubation of SS for 6 mo did not result in a substantial decrease in OM content or a change in the relative distribution of Cu, Zn, Pb, and As. Direct OM oxidation to 30 and 70% by diluted HO resulted in a significant decrease in organically bound Cu but increased its exchangeable, carbonate-bound, and Fe/Mn-bound fractions. Oxidation of OM slightly decreased organically bound Zn but significantly increased exchangeable Zn in all SSs. Oxide- and carbonate-bound Zn also decreased following OM oxidation. Exchangeable fractions of As and Pb were minute before and after OM degradation, indicating that release into the environment would be unlikely. The relative distribution of Cu, Zn, Pb, and As in SS-treated soils was similar to that of SS, suggesting a dominant role of SS properties in controlling metal distribution following OM oxidation. Overall, OM oxidation increased the mobility and bioavailability of Zn and Cu, whereas it had less impact on Pb and As.     

Concentration and chemical speciation for the determination of Cu,Zn, Ni,Pb and Cd from refuse dump soils using the optimized BCR sequential extraction procedure

The optimized BCR sequential extraction procedure (proposed by the Standards, Measurements and Testing Programme (SM&T) of the European Union) was applied to seven topsoil samples from refuse dump sites for the determination of Cu, Zn, Ni, Pb and Cd. The metals were partitioned into four operationally defined chemical fractions: acid extractable, reducible, oxidizable and residual, and analysed using flame atomic absorption spectrophotometry, FAAS. The results were compared with total metal concentrations obtained using HNO₃, HClO₄ and HF digestion procedures. Results for total metal analysis ranged from - 15.55 to 43.45 for Cu, 37.15 to 222.35 for Zn, 5.15 to 12.10 for Ni, 10.30 to 93.05 for Pb and 0.35 to 3.75 for Cd in μgg⁻¹ dry weight. The results of the partitioning study showed that zinc prevailed in the more soluble fractions and was distributed between the acid-extractable (32.4%) and the reducible (40.3%) fractions, whereas Pb was distributed mainly in the reducible fraction. Copper and nickel were predominantly associated with the reducible and residual fractions - 53.4, 33.3 and 51.1, 24.1% respectively. The ranking of the four fractions for the partitioning of cadmium was: reducible > residual > oxidizable > acid extractable. The percentage recovery for all metals when comparing total metal concentration with the fractional sum of the optimized BCR procedure, were of the order: Zn(93%) > Pb(83%) > Cu(78) > Cd > (68%) > Ni(63%).     

In situ soil treatments to reduce the phyto- and bioavailability of lead, zinc, and cadmium

A study was established near a former Zn and Pb smelter to test the ability of soil amendments to reduce the availability of Pb, Zn, and Cd in situ. Soil collected from the field was amended in the lab with P added as 1% P-H3PO4, biosolids compost added at 10% (referred to hereafter as "compost"), and a high-Fe by-product (referred to hereafter as "Fe") + P-triple superphosphate (TSP) (2.5% Fe + 1% P-TSP) and incubated under laboratory conditions at a constant soil pH. Changes in Pb bioavailability were measured with an in vitro test and a feeding study with weanling rats. Field-amended and incubated soils using these plus additional treatments were evaluated using the in vitro extraction and tall fescue (Festuca arundinacea Schreb. cv. Kentucky-31) metal concentration. Reductions were observed across all parameters but were not consistent. In the feeding study, the 1% P-H3PO4 and compost treatments resulted in a decrease of 26% in rat tissue Pb concentration compared with the control soil. The 2.5% Fe + 1% P-TSP showed a 39% decrease. The 1% P-H3PO4 treatment caused the greatest reduction in in vitro extractable Pb from field samples (pH 2.2) with a measured reduction of 66%, while the compost treatment had a 39% reduction and the 2.5% Fe + 1% P-TSP treatment a 50% reduction. The in vitro extraction (pH 1.5) run on field samples showed no reduction in the compost or Fe treatments. The 1% P-H3PO4 treatment was the most effective at reducing plant Pb, Zn, and Cd.     

Geochemical partitioning of copper, lead, and zinc in benthic, estuarine sediment profiles

The geochemical partitioning of copper (Cu), lead (Pb), and zinc (Zn) was examined in benthic sediment profiles (0- to 20-cm depth interval) composed of relatively coarse (65-90% sand-sized particles), noncohesive, suboxic material (Eh +120 to +260 mV). Total Cu, Pb, and Zn concentrations ranged from 8.3 to 194, 16.3 to 74.8, and 30.1 to 220 mg/kg, respectively, and were related to vertical trends in sediment texture. The observed distribution coefficients describing solid-solution partitioning were in the range of 100 to 1000 L/kg. The geochemical partitioning of solid-phase Cu, Pb, and Zn between six operationally defined fractions was examined with a sequential extraction scheme. The association of Cu, Pb, and Zn with amorphous oxides, crystalline oxides, and organic matter was linearly dependent on the abundance of each respective phase. For retention by amorphous oxide minerals, the observed stoichiometry ranged from 5.2 to 23.7 mg/g for Cu, 12.8 to 21.5 mg/g for Pb, and 23.1 to 85.7 mg/g for Zn. Corresponding values for association with crystalline oxides were an order of magnitude less than those for amorphous oxides, indicating a lesser affinity of trace metals for crystalline oxides. The stoichiometric relationships describing association with organic matter ranged from 17.6 to 54.0 mg/g for Cu, 6.1 to 9.6 mg/g for Pb, and 6.4 to 16.4 mg/g for Zn. The results from this study provide an insight into processes controlling trace metal partitioning in coarse-textured, suboxic, estuarine sediments.     

The availability of copper in soils historically amended with sewage sludge, manure, and compost

Metals in soils amended with sewage sludge are typically less available compared with those in soils spiked with soluble metal salts. However, it is unclear if this difference remains in the long term. A survey of copper (Cu) availability was made in soils amended with sewage sludge, manure, and compost, collectively named organic amendments. Paired sets of amended and control soils were collected from 22 field trials where the organic amendments had aged up to 112 yr. Amended soils had higher total Cu concentrations (range, 2-220 mg Cu kg; median, 15 mg Cu kg) and organic C (range, 1-16 g kg; median, 4 g kg) than control soils. All samples were freshly spiked with CuCl, and the toxicity of added Cu to barley was compared between amended and control soils. The toxicity of added Cu was significantly lower in amended soils than in control soil in 15 sets by, on average, a factor of 1.4, suggesting that aged amendments do not largely increase Cu binding sites. The fraction of added Cu that is isotopic exchangeable Cu (labile Cu) was compared between control soils freshly spiked with CuCl and amended soils with both soils at identical total Cu concentrations. Copper derived from amendments was significantly less labile (on average 5.9-fold) than freshly added Cu in 18 sets of soils. This study shows that Cu availability after long-term applications of organic amendments is lower than that of freshly added Cu salts, mainly because of its lower availability in the original matrix and ageing reactions than because of increased metal binding sites in soil.     

Fractionation and mobility of copper, lead, and zinc in soil profiles in the vicinity of a copper smelter

Four soil profiles located near a copper smelter in Poland were investigated for the distribution and chemical fractions of Cu, Pb, and Zn and their mobility in relation to soil properties. Contamination with heavy metals was primarily restricted to surface horizons and the extent of contamination was 7- to 115-fold for Cu, 30-fold for Pb, and 6-fold for Zn as compared with subsurface horizons. In the less-contaminated fine-textured soil, the metals were distributed in the order: residual > Fe-Mn oxides occluded > organically complexed > exchangeable and specifically adsorbed, while the order for sandy soils was: residual > organically complexed > Fe-Mn oxides occluded > exchangeable and specifically adsorbed. The contaminated surface horizons of these profiles showed no consistent pattern of metal distribution. However, the common features of highly contaminated soils were very low percentage of residual fraction and the dominance of the NH4OAc extractable fraction. The sum of mobile metal fractions was generally < 10% in subsurface horizons, while in the contaminated surface horizons these fractions made up 50% of the total metal contents. Soil properties contributed more to the relative distribution of the metal fractions in the studied profiles than did the distance and direction to the source of pollution. The amounts of metal extracted by 0.01 M CaCl2 accounted for only a small part of the same metals extracted by NH4OAc. The mobility indexes of metals correlated positively and significantly with the total content of metals and negatively with the clay content.     

Arsenic, cadmium, and lead in California cropland soils: role of phosphate and micronutrient fertilizers

Phosphate and micronutrient fertilizers contain potentially harmful trace elements, such as arsenic (As), cadmium (Cd), and lead (Pb). We investigated if application of these fertilizer increases the As, Cd, and Pb concentrations of the receiving soils. More than 1000 soil samples were collected in seven major vegetable production regions across California. Benchmark soils (no or low fertilizer input) sampled in 1967 and re-sampled in 2001 served as a baseline. Soils were analyzed for total concentrations of As, Cd, Pb, P, and Zn. The P and Zn concentrations of the soils were indicators of P fertilizer and micronutrient inputs, respectively. Results showed that the concentrations of these elements in the vegetable production fields in some production areas of California had been shifted upward. Principal component analysis and cluster analysis showed that the seven production areas could be sorted into three categories: (i) enrichment of As, Cd, and Pb, which was associated with the enrichment of P and Zn in one of the seven areas surveyed; (ii) enrichment of As, which was associated with enrichment of Zn in two of the seven areas surveyed; and (iii) no remarkable correlation between enrichment of As, Cd, and Pb and enrichment of P and Zn in the other four areas surveyed.     

Adsorption of cadmium, copper, nickel, and zinc to a poly(tetrafluorethene) porous soil solution sampler

Suction cups made of poly(tetrafluorethene) (PTFE) are widely used for sampling of soil solution. A brand (Prenart) of PTFE cups was tested for adsorption of Cd, Cu, Ni, and Zn at low concentrations under different conditions. In a laboratory experiment adsorption from a 10 microg L(-1) heavy metal solution with a 0.01 M NaCl background electrolyte was investigated at pH 3.6, 4.5, and 5.8 by pumping the solutions through the cups. The effect of three different ionic compositions was also investigated using 0.01 M CaCl2, 0.01 M NaCl, and no background electrolyte at pH 4.5. In 0.01 M NaCl electrolyte at pH 5.8 the cups acted as effective filters. At pH 3.6 after 300 mL of solution had passed through the cup, equivalence between the Cd and Ni concentrations in influent and effluent was found. No equivalence between effluent and influent concentrations was found for Zn and Cu at pH 4.5 and 5.8. With Ca as the electrolyte, no adsorption of Cd, Ni, or Zn was found. In Na electrolyte, equivalence between influent and effluent concentrations for Cd, Ni, and Zn was reached. The difference between effluent and influent concentrations of Zn, Ni, and Cd remained significant in the absence of electrolyte. For all pH values and electrolytes the difference between effluent and influent concentrations of Cu was significant. It is concluded that PTFE cups affect the concentrations of heavy metals sampled at low soil solution concentrations. Cadmium, Cu, Ni, and Zn adsorb to the cup at pH > 4.5 and low ionic strength.     

Plant-available zinc and lead in mine spoils and soils at the mines of Spain, Iowa

To investigate the forms of Zn and Pb and their plant availability in mine spoil long after its abandonment, we studied seven sites in the Mines of Spain, near Dubuque, IA. Ores of Zn and Pb were mined from dolomitic limestone primarily during the 19th century, and there had been no subsequent remediation of metals-contaminated spoil. From both mine spoil and undisturbed areas, we collected root-zone soil samples as well as samples of the dominant ground-level, native plants, aniseroot [Osmorhiza longistylis (Torr.) DC.] and black snakeroot (Sanicular marilandica L.). We determined Zn and Pb concentrations in both the plant tissue and in the soil samples after strong-acid digestion, and we fractionated the solid-phase forms of Zn, Pb, and P in the soil samples by using sequential extraction. Concentrations of total Zn and Pb were 10- to 20-fold greater in the spoil than in the undisturbed soils. Plants growing in the mine spoil had Zn concentrations two to four times greater and Pb concentrations more than 26 times greater than did plants growing in the undisturbed soils. The highest concentrations of Zn and Pb were in the CBD-extractable and the residual fractions in both undisturbed and mine spoil samples. Although the mine spoil contained large amounts of P, Zn, and Pb were available for uptake by the two plant species in amounts proportional to Zn and Pb concentrations in the rooting zone.     

Distribution of copper, zinc, and phosphorus in coastal plain soils receiving repeated liquid biosolids applications

Continuous N-based application of biosolids contributes to a gradual increase of trace elements and P in soils. The objectives of this study were to assess the accumulation and vertical transport of Cu, Zn, C, N, and P within the profile of two coastal plain soils. Liquid (6-8% total solids) biosolids were applied to an Acredale silt loam (fine silty, mixed, thermic typic Ochraqualfs) and Bojac loamy sand (coarse loamy, mixed, thermic typic Hapludult) annually from 1984 to 1998. The repeated applications supplied 70, 204, and 3823 kg ha(-1) of Cu, Zn, and P, respectively, to the Acredale and 81, 225, and 4265 kg ha(-1) of Cu, Zn, and P, respectively, to the Bojac. The total C and N contents were not different than background levels in the Bojac soil and were slightly higher in the Acredale soil 7 years after cessation of biosolids application. Phosphorus, Cu and Zn are still concentrated in the top 0.25 m of the Acredale soil. Enrichment of P, Cu, and Zn were detected to the deepest soil increment in the coarse-textured Bojac soil. Approximately 20 to 40% of the Cu and Zn applied in the biosolids could not be accounted, which was likely due to a combination of leaching and incomplete extraction. Excessive Mehlich 1-P concentrations and a high degree of P saturation were found in amended soil, raising the potential for P release to runoff or leaching water.     

Enhanced transformation of lead speciation in rhizosphere soils using phosphorus amendments and phytostabilization: an x-ray absorption fine structure spectroscopy investigation

To formulate successful phytostabilization strategies in a shooting range soil, understanding how heavy metals are immobilized at the molecular level in the rhizosphere soil is critical. Lead (Pb) speciation and solubility in rhizosphere soils of five different plant species were investigated using extended X-ray absorption fine structure (EXAFS) spectroscopy and chemical extraction. The EXAFS analysis indicated that Pb occurred as PbCO (37%), Pb sorbed to organic matter (Pb-org: 15%), and Pb sorbed to pedogenic birnessite and/or ferrihydrite (Pb-ox: 36%) in the bulk soil. Comparison of the EXAFS spectra between bulk and rhizosphere soils demonstrated notable differences in fine structure, indicating that Pb species had been modified by rhizosphere processes. The estimated proportion of PbCO (25%) in the buckwheat soil was smaller than the other rhizosphere soils (35-39%). The addition of P significantly reduced Pb solubility in the bulk and rhizosphere soil except in the rhizosphere of buckwheat, for which the Pb solubility was 10-fold greater than in the other P-amended soils. This larger solubility in the buckwheat rhizosphere could not be explained by the total Pb speciation in the soil but was presumably related to the acidifying effect of buckwheat, resulting in a decrease of the soil pH by 0.4 units. The reduced Pb solubility by P amendment resulted from the transformation of preexisting PbCO (37%) into Pb(PO)Cl (26-32%) in the bulk and rhizosphere soils. In the P-amended rhizosphere soils, Pb-org species were no longer detected, and the Pb-ox pool increased (51-57%). The present study demonstrated that rhizosphere processes modify Pb solubility and speciation in P-amended soils and that some plant species, like buckwheat, may impair the efficiency of Pb immobilization by P amendments.     

In situ accumulation of copper, chromium, nickel, and zinc in soils used for long-term waste water reclamation

We studied the long-term in situ accumulation of Cu, Cr, Ni, and Zn in the soil profile of a large-scale effluent recharge basin after 24 yr of operation in a wastewater reclamation plant using the Soil Aquifer System approach in the Coastal Plain of Israel. The objective was to quantify metals accumulation in the basin's soil profile, clarify retention mechanisms, and calculate material balances and metal removal efficiency as the metal loads increase. Effluent recharge led to measurable accumulation, relative to the pristine soil, of Ni and Zn in the 0- to 4-m soil profile, with concentration increases of 0.3 to 1.3 mg kg(-1) and 2.9 to 6.4 mg kg(-1), respectively. Copper accumulated only in the 0- to 1-m top soil layer, with concentration increase of 0.28 to 0.76 mg kg(-1). Chromium concentration increased by 3.1 to 7.3 mg kg(-1) in the 0- to 1-m horizon and 0.9 to 2.3 mg kg(-1) at deeper horizons. Sequential selective extraction showed Cu tended to be preferentially retained by Fe oxides and organic matter (OM), Cr by OM, Ni by OM, and carbonate and Zn by carbonate. The average total retained amounts of Cu, Cr, Ni, and Zn were 0.7 +/- 1.0, 13.6 +/- 4.8, 4.3 +/- 3.6, and 28.7 +/- 5.4 g per a representative unit soil slab (1 m(2) x 4 m) of the basin, respectively. This amounts to 3.6 +/- 4.9%, 79.5 +/- 28.0%, 8.0 +/- 6.9%, and 9.3 +/- 1.8% of the Cu, Cr, Ni, and Zn loads, respectively, applied during 24 yr of effluent recharge (total of approximately 1880 m effluent load). The low long-term overall removal efficiency of the metals from the recharged effluent in the top horizon may be due to the metals' low concentrations in the recharged effluent and the low adsorption affinity and retention capacity of the sandy soil toward them. This leads to attainment of a quasi-equilibrium and a steady state in element distribution between the recharged effluent solution and the soil after few years of recharge and relatively small cumulative effluent loadings.     

Optimization of the electrocoagulation process for the removal of copper, lead and cadmium in natural waters and simulated wastewater

Chemical, electrochemical and flow variables were optimized to examine the effectiveness of the electrocoagulation process for the removal of copper, lead and cadmium. The electrochemical process, which uses electrodes of commercial laminate steel, was applied to simulated wastewater containing 12 mg dm(-3) of copper, 4 mg dm(-3) of lead and 4 mg dm(-3) of cadmium. The optimum conditions for the process were identified as pH=7, flow rate=6.3 cm(3) min(-1) and a current density between 31 and 54 A m(-2). When the electrode geometric area and time of electrolysis reached critical values, the copper removal reached a maximum value of 80%. A linear relationship was identified between the current density and the mass of generated sludge. In addition, a linear relationship was found between specific energy consumption and current density. The results of this investigation provide important data for the development of an industrial-scale electrolytic reactor.