集多种特性的三次三角伪B样条

目的 为了同时解决传统多项式B样条曲线在形状调控、精确表示常见工程曲线以及构造插值曲线时的不足,提出了一类集多种特性的三次三角伪B样条。方法 首先构造了一组带两个参数的三次三角伪B样条基函数,然后在此基础上定义了相应的参数伪B样条曲线,并讨论了该曲线的特性及光顺性问题,最后研究了相应的代数伪B样条,并给出了最优代数伪B样条的确定方法。结果 参数伪B样条曲线不仅满足C²连续,而且无需求解方程系统即可自动插值于给定的型值点。当型值点保持不变时,插值曲线的形状还可通过自带的两个参数进行调控。在适当条件下,该参数伪B样条曲线可精确表示圆弧、椭圆弧、星形线等常见的工程曲线。相应的代数伪B样条具有参数伪B样条曲线类似的性质,利用最优代数伪B样条可获得满意的插值效果。结论 所提出的伪B样条同时解决了传统多项式B样条曲线在形状调控、精确表示常见工程曲线以及构造插值曲线时的不足,是一种实用的曲线造型方法。     

非均匀节点情形下的一类三角B样条曲线

给出一类在非均匀节点情形下带参数的三角B样条基函数,讨论了这类基函数的性质以及在重节点情形时的变化,并利用这类基函数构造了相应的三角B样条曲线,这类曲线具有与二次非均匀B样条曲线相似的性质。在控制顶点不变的情况下,可以通过改变形状参数取值来调节曲线的形状。此外,它还能精确表示圆、椭圆等曲线。     

基于Gβ连续的三次代数三角多项式样条构造及其应用

为了完善三角多项式样条的算法,本文基于空间｛1,sint ,cost,sin^2t｝ ,构造了三次代数三角 Gβ样条曲线（三次AT- Gβ样条曲线）,包括曲线的构造,几何连续的条件、求解等,推出AT- Gβ样条曲线的性质以及研究形状参数β1 和β2 对曲线的影响等.还通过曲线反推控制顶点,研究三次插值AT-Gβ 样条. 这种三次AT- Gβ样条曲线具有良好的局部性质和广泛的应用.     

一种带形状参数的三角样条曲线

本文针对三次B样条曲线相对于其控制多边形形状固定,不能描述除抛物线以外的圆锥曲线的不足进行改进。将形状参数与三角函数进行有机结合,构造了一组含参数的三角样条基,基于这组基定义了一种结构类似于三次B样条曲线的带形状参数的三角样条曲线。新曲线在继承B样条曲线主要优点的同时,既具有形状可调性,又能精确表示椭圆,而且其连续性和对控制多边形的逼近性也都优于三次B样条曲线。对于等距节点,在一般情况下该曲线整体C3连续,在特殊条件下可达C5连续。利用张量积方法,将曲线推广后所得到的曲面具有与曲线类似的性质,给出了用曲面表示椭球面的方法。     

4阶均匀代数三角样条空间的拟Legendre基

为解决代数三角样条空间上正交基的理论问题,提出了4阶均匀代数三角样条空间上构造正交基的方法.该方法利用6阶C-B样条基函数构造一组辅助函数,并以这组辅助函数的二阶导数形式定义样条空间上的一组正交基,称为拟Legendre基.实例结果表明,使用这组正交基可以简化内积计算,便于最佳平方逼近问题求解.     

一种类四次三角样条曲线

针对B样条曲线相对于其控制多边形形状固定,以及不能描述除抛物线以外的圆锥曲线的不足进行改进。将形状参数与三角函数进行有机结合,构造了一组含参数的三角基,由这组基定义了带形状参数的三角样条曲线,其每一段由相继的5个控制顶点生成。新曲线在继承B样条曲线主要优点的同时,既具有形状可调性,又能精确表示椭圆,对于等距节点,在一般情况下曲线C³连续,当形状参数取特殊值时曲线可达C⁵连续。采用张量积方法,将曲线推广后所得到的曲面具有与曲线类似的性质,给出了用曲面表示椭球面的方法。     

带形状参数三角B样条曲线曲面及其应用

针对样条曲线曲面构造及其在图像放缩中的应用问题,在三角函数空间{1,t,sint,cost,sin2 t,cos2 t}中构造一类带有形状参数的三角B样条基函数,并定义相应的三角B样条曲线和曲面,分析该曲线曲面的性质以及形状参数对曲线曲面形状的调节作用。拓宽形状参数的取值,构造了满足C2连续且可以直接插值控制顶点的三角B样条插值曲线和曲面,并将其应用于图像放缩中。实例说明了所构造的三角B样条曲线曲面在曲线曲面造型和图像放缩方面有较好应用。     

基于双阶样条的代数双曲B样条升阶及割角算法

考虑代数双曲B样条曲线的升阶问题,从理论上证明了曲线的升阶可以理解为控制顶点的割角过程.为了实现代数双曲B样条曲线的升阶,文中构造了一组基函数——双阶代数双曲B样条基函数,这组基函数并不具有统一的阶数,而具有"双阶"性质.代数双曲B样条基函数与双阶样条基函数之间的变换公式可以导出曲线升阶的割角算法.     

带形状参数的类三次代数三角Hermite参数样条曲线

基于空间{1,t,sin t,cos t,sin~2t}提出了一类带形状参数的类三次代数三角Hermite参数样条曲线。该曲线不仅具有标准三次Hermite参数样条曲线的性质,而且在适当条件下能够精确表示圆、椭圆、抛物线等工程曲线。在给定插值条件时还可通过改变形状参数的取值对曲线的形状进行调控。同时,还基于光顺准则建立求解最优形状参数的数学模型,根据实际需要,该模型所求的形状参数能使得曲线达到C~1或C~2连续。实例表明,利用模型求解的最优形状参数能保证曲线具有良好的光顺性。     

带形状参数的C~2连续类三次三角样条曲线

传统的三次均匀B样条曲线在给定控制顶点时其形状不能调整,以及不能精确表示圆锥曲线。针对三次均匀B样条曲线的不足,提出了一种带形状参数的C2连续的类三次三角样条曲线。该曲线不仅与三次均匀B样条曲线具有相似的性质,而且在控制顶点保持不变时其形状可通过形状参数的取值进行调整。在适当条件下,类三次三角样条曲线比三次均匀B样条曲线更能逼近于控制多边形,且能精确表示圆、椭圆、抛物线等圆锥曲线。     

Only connect: teaching, technology and telesis

Abstract This paper describes an approach to the design of interactive multimedia materials being developed in a European Community project. The developmental process is seen as a dialogue between technologists and teachers. This dialogue is often problematic because of the differences in training, experience and culture between them. Conditions needed for fruitful dialogue are described and the generic model for learning design used in the project is explained.     

European Community policy and the market

Abstract This paper starts with some reflections on the policy considerations and priorities which are shaping European Commission (EC) research programmes. Then it attempts to position the current projects which seek to capitalise on information and communications technologies for learning in relation to these priorities and the apparent realities of the marketplace. It concludes that while there are grounds to be optimistic about the contribution EC programmes can make to the efficiency and standard of education and training, they are still too technology driven.     

一种自适应子融合集成多分类器方法

融合集成方法已经广泛应用在模式识别领域,然而一些基分类器实时性能稳定性较差,导致多分类器融合性能差,针对上述问题本文提出了一种新的基于多分类器的子融合集成分类器系统。该方法考虑在度量层融合层次之上通过对各类基多分类器进行动态选择,票数最多的类别作为融合系统中对特征向量识别的类别,构成一种新的自适应子融合集成分类器方法。实验表明,该方法比传统的分类器以及分类融合方法识别准确率明显更高,具有更好的鲁棒性。     

Avoiding semantic and temporal gaps in developing software intensive systems

Development of software intensive systems (systems) in practice involves a series of self-contained phases for the lifecycle of a system. Semantic and temporal gaps, which occur among phases and among developer disciplines within and across phases, hinder the ongoing development of a system because of the interdependencies among phases and among disciplines. Such gaps are magnified among systems that are developed at different times by different development teams, which may limit reuse of artifacts of systems development and interoperability among the systems. This article discusses such gaps and a systems development process for avoiding them.     

Designing economic np control charts: A programmed simulation approach

This paper presents control charts models and the necessary simulation software for the location of economic values of the control parameters. The simulation program is written in FORTRAN, requires only 10K of main storage, and can run on most mini and micro computers. Two models are presented - one describes the process when it is operating at full capacity and the other when the process is operating under capacity. The models allow the product quality to deteriorate to a further level before an existing out-of-control state is detected, and they can also be used in situations where no prior knowledge exists of the out-of-control causes and the resulting proportion defectives.     

The development of robot art

Going through a few examples of robot artists who are recognized worldwide, we try to analyze the deepest meaning of what is called “robot art” and the related art field definition. We also try to highlight its well-marked borders, such as kinetic sculptures, kinetic art, cyber art, and cyberpunk. A brief excursion into the importance of the context, the message, and its semiotics is also provided, case by case, together with a few hints on the history of this discipline in the light of an artistic perspective. Therefore, the aim of this article is to try to summarize the main characteristics that might classify robot art as a unique and innovative discipline, and to track down some of the principles by which a robotic artifact can or cannot be considered an art piece in terms of social, cultural, and strictly artistic interest. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

煤矿井下安全监控分站的设计及其仿真实现

为了设计一种具有低成本、低功耗、易操作、功能强且可靠性高的煤矿井下安全分站,针对煤矿安全生产实际,文章提出了采用MCS-51系列单片机为核心、具有CAN总线通信接口的煤矿井下安全监控分站的设计方案;首先给出煤矿井下安全监控分站的整体构架设计,然后着重阐述模拟量输入信号处理系统的设计过程,最后说明单片机最小系统及其键盘、显示、报警、通信等各个组成部分的设计;为验证设计方案的可行性与有效性,使用Proteus软件对设计内容进行仿真验证,设计的煤矿井下安全监控分站具有瓦斯、温度等模拟量参数超标报警功能和电机开停、风门开闭等开关量指示功能;仿真结果表明:设计的煤矿井下安全监控分站具有一定的实际应用价值.     

Explanation and prediction: an architecture for default and abductive reasoning

Although there are many arguments that logic is an appropriate tool for artificial intelligence, there has been a perceived problem with the monotonicity of classical logic. This paper elaborates on the idea that reasoning should be viewed as theory formation where logic tells us the consequences of our assumptions. The two activities of predicting what is expected to be true and explaining observations are considered in a simple theory formation framework. Properties of each activity are discussed, along with a number of proposals as to what should be predicted or accepted as reasonable explanations. An architecture is proposed to combine explanation and prediction into one coherent framework. Algorithms used to implement the system as well as examples from a running implementation are given.     

Three Process Perspectives: Organizations, Teams, and People

This paper provides the author's personal views and perspectives on software process improvement. Starting with his first work on technology assessment in IBM over 20 years ago, Watts Humphrey describes the process improvement work he has been directly involved in. This includes the development of the early process assessment methods, the original design of the CMM, and the introduction of the Personal Software Process (PSP)^SM and Team Software Process (TSP){^SM}. In addition to describing the original motivation for this work, the author also reviews many of the problems he and his associates encountered and why they solved them the way they did. He also comments on the outstanding issues and likely directions for future work. Finally, this work has built on the experiences and contributions of many people. Mr. Humphrey only describes work that he was personally involved in and he names many of the key contributors. However, so many people have been involved in this work that a full list of the important participants would be impractical.     

基于复小波噪声方差显著修正的SAR图像去噪

提出了一种基于复小波域统计建模与噪声方差估计显著性修正相结合的合成孔径雷达(Synthetic Aperture Radar,SAR)图像斑点噪声滤波方法。该方法首先通过对数变换将乘性噪声模型转化为加性噪声模型,然后对变换后的图像进行双树复小波变换(Dualtree Complex Wavelet Transform,DCWT),并对复数小波系数的统计分布进行建模。在此先验分布的基础上,通过运用贝叶斯估计方法从含噪系数中恢复原始系数,达到滤除噪声的目的。实验结果表明该方法在去除噪声的同时保留了图像的细节信息,取得了很好的降噪效果。