Effects of preparing conditions on the electrodeposition of well-aligned ZnO nanorod arrays

By using a potentiostatic electrodeposition method, well-aligned ZnO nanorod arrays (ZNAs) were synthesized under different conditions. The effects of preparing conditions on the electrodeposition of ZNAs were systematically studied by scanning electron microscopy (SEM), X-ray diffraction (XRD) and absorbance spectroscopy. It is indicated that the electrodeposition parameters, such as electrodeposition potential, electrolyte pH, concentration of precursors, temperature of solution and electrodeposition time, have significant influence on the morphology, diameter, density and growth rate of ZNAs. The ZNAs, with well-defined crystallization, can be only obtained when the applied potential is controlled from −0.4 to −1.0 V. The growth temperature has great impact on the morphology of ZnO nanostructure but it is weakly related to the band gap (E_g) of ZNAs. The rod diameters can be monitored to some extent only by changing the concentration of the precursors. The electrolyte pH value has relative influence on the diameter of ZNAs. With the growth time increasing, ZNAs with high aspect ratio can be gained.     

Efficiency improvement of silicon solar cells enabled by ZnO nanowhisker array coating

An efficient antireflection coating is critical for the improvement of silicon solar cell performance via increased light coupling. Here, we have grown well-aligned ZnO nanowhisker (NW) arrays on Czochralski silicon solar cells by a seeding-growth two-step process. It is found that the ZnO NWs have a great effect on the macroscopic antireflection effect and, therefore, improves the solar cell performance. The ZnO NW array-coated solar cells display a broadband reflection suppression from 500 to 1,100 nm, and the minimum reflectance smaller than 3% can easily be achieved. By optimizing the time of ZnO NW growth, it has been confirmed that an increase of 3% relatively in the solar cell efficiency can be obtained. These results are quite interesting for the application of ZnO nanostructure in the fabrication of high-efficiency silicon solar cells.     

Improved dye-sensitized solar cell with a ZnO nanotree photoanode by hydrothermal method

This study investigated the influence of ZnO nanostructures on dye adsorption to increase the photovoltaic conversion efficiency of solar cells. ZnO nanostructures were grown in both tree-like and nanorod (NR) arrays on an AZO/FTO film structure by using a hydrothermal method. The results were observed in detail using X-ray diffraction, field-emission scanning electron microscopy (FE-SEM), UV-visible spectrophotometry, electrochemical impedance spectroscopy, and solar simulation. The selective growth of tree-like ZnO was found to exhibit higher dye adsorption loading and conversion efficiency than ZnO NRs. The multiple ‘branches’ of ‘tree-like nanostructures’ increases the surface area for higher light harvesting and dye loading while reducing charge recombination. These improvements result in a 15% enhancement in power conversion. The objective of this study is to facilitate the development of a ZnO-based dye-sensitized solar cell.     

Efficiency improvement of InGaP/GaAs/Ge solar cells by hydrothermal-deposited ZnO nanotube structure

In this paper, a zinc oxide (ZnO) nanotube, fabricated by the hydrothermal growth method on triple-junction (T-J) solar cell devices to enhance efficiency, is investigated. Compared to those of bare T-J solar cells (without antireflection (AR) coating) and solar cells with Si₃N₄ AR coatings, the experimental results show that the T-J solar cells, which use a ZnO nanotube as an AR coating, have the lowest reflectance in the short wavelength spectrum. The ZnO nanotube has the lowest light reflection among all experimental samples, especially in the range of 350 to 500 nm from ultraviolet (UV) to visible light. It was found that a ZnO nanotube can enhance the conversion efficiency by 4.9%, compared with a conventional T-J solar cell. The Si₃N₄ AR coatings also enhance the conversion efficiency by 3.2%.The results show that a cell with ZnO nanotube coating could greatly improve solar cell performances.     

Efficiency improvement of CIGS solar cells using RF sputtered TCO/Ag/TCO thin-film as prospective buffer layer

In this paper, TCO (Transparent Conductive Oxide) incorporating ultrathin Ag intermediate film is proposed as a new buffer layer to enhance the efficiency of CIGS thin-film solar cells (TFSCs). In this regard, versatile multilayer thin-films based on ZnO/Ag/ZnO and ITO/Ag/ITO structures were deposited on glass using RF magnetron sputtering technique to determine the optoelectronic parameters of the multilayer structures. The elaborated samples were then characterized using SEM, EDS, XRD, and UV–Visible absorption spectroscopy techniques to investigate the structure morphological, optical, and electronic properties. The deposited multilayer thin-films showed amorphous-like structure and exhibited a broadband absorbance over the visible and even NIR spectrum ranges, indicating its potential application as alternative buffer layers for thin-film solar cells. In this context, TCO/Ag/TCO/CIGS solar cells have been numerically investigated using the deposited multilayer optoelectronic properties. It was revealed that the estimated efficiency of the ZnO/Ag/ZnO/CIGS-based solar cell could reach 18.5% with an open circuit voltage of 0.7 V and a short-circuit current density of 34.8 mA/cm². The performances exhibited by the investigated solar cell demonstrated that ZnO/Ag/ZnO multilayer can be used as an alternative to the conventional CdS buffer layer for developing high-performance non-toxic CIGS solar cells.     

Fabrication of Blanket-Like Assembled ZnO Nanowhiskers Using an Aqueous Solution

Blanket-like assembled ZnO nanowhiskers were fabricated using a freestanding ZnO nanoparticle layer by an aqueous solution deposition. X-ray diffraction and field emission scanning electron microscopy clarified the crystalline phase, orientation, morphology, and microstructure. Thermal treatment of the zinc acetate dihydrate layer resulted in the formation and delamination of the ZnO nanoparticle layer on the glass substrate. The growth habits of ZnO crystals resulted in the growth of ZnO nanowhiskers preferentially orientated along the direction of the c -axis on the whole surface of the freestanding ZnO nanoparticle layer by heterogeneorous nucleation and growth. The hierarchical-structured blanket-like ZnO nanowhisker assemblies can be utilized for dye-sensitive solar cells and gas sensors because of their high surface-to-volume ratio.     

Electrodeposition of CdSe coatings on ZnO nanowire arrays for extremely thin absorber solar cells

We report on electrodeposition of CdSe coatings onto ZnO nanowire arrays and determine the effect of processing conditions on material properties such as morphology and microstructure. CdSe-coated ZnO nanowire arrays have potential use in extremely thin absorber (ETA) solar cells, where CdSe absorbs visible light and injects photoexcited electrons into the ZnO nanowires. We show that room-temperature electrodeposition enables growth of CdSe coatings that are highly crystalline, uniform, and conformal with precise control over thickness and microstructure. X-ray diffraction and transmission electron microscopy show nanocrystalline CdSe in both hexagonal and cubic phases with grain size ∼5 nm. Coating morphology depends on electrodeposition current density. Uniform and conformal coatings were achieved using moderate current densities of ∼2 mA cm⁻² for nanowires with roughness factor of ∼10, while lower current densities resulted in sparse nucleation and growth of larger, isolated islands. Electrodeposition charge density controls the thickness of the CdSe coating, which was exploited to investigate the evolution of the morphology at early stages of nucleation and growth. UV–vis transmission spectroscopy and photoelectrochemical solar cell measurements demonstrate that CdSe effectively sensitizes ZnO nanowires to visible light.     

Hybrid polymer/ZnO solar cells sensitized by PbS quantum dots

Poly[2-methoxy-5-(2-ethylhexyloxy-p-phenylenevinylene)]/ZnO nanorod hybrid solar cells consisting of PbS quantum dots [QDs] prepared by a chemical bath deposition method were fabricated. An optimum coating of the QDs on the ZnO nanorods could strongly improve the performance of the solar cells. A maximum power conversion efficiency of 0.42% was achieved for the PbS QDs' sensitive solar cell coated by 4 cycles, which was increased almost five times compared with the solar cell without using PbS QDs. The improved efficiency is attributed to the cascade structure formed by the PbS QD coating, which results in enhanced open-circuit voltage and exciton dissociation efficiency.     

Bottom-up self-assembly of macroporous ZnO nanostructures for photovoltaic applications

The present study utilized a template-assisted electrodeposition route for the bottom-up epitaxial growth of macroporous zinc oxide nanostructures. To this end, the ZnO seed layer was coated on the p-type silicon substrates using a radio frequency magnetron sputtering technique to form a p-n heterojunction. Then, polymer microspheres were implanted on ZnO/Si substrates to act as a template. Subsequently, ZnO nanostructures were electrodeposited through the interstitial spaces between the microspheres. After the deposition, the microspheres were removed by dissolving in chloroform solvent, forming a porous structure. The planar and cross-sectional electron microscopy analyses exhibited a uniform macroporous morphology with an average pore diameter of ∼1 μm. The pores were homogeneously distributed on the surface of the electrodeposited ZnO layer. The advantage of this technique over the top-down approaches, such as electrochemical etching, is that the porosity and size of pores can be easily adjusted by varying the concentration and diameter of microsphere templates. The optical investigations revealed enhancement in photon absorption and photoluminescence (PL) intensity due to multiple light scattering in the pore walls of the deposited ZnO nanostructures. For the templated sample, a PL blue shift was observed due to the reduction in crystallite size of ZnO nanostructures. A heterojunction thin film solar cell was designed by the metallization of ZnO/p-Si samples to study the power conversion capability of macroporous ZnO nanostructures. The photovoltaic performance of the developed devices was evaluated under a solar light simulator. The device based on the templated sample showed increased shunt resistance and reduced series resistance compared to the flat sample. The optoelectrical results indicated an efficiency improvement for the fabricated solar cells based on the macroporous ZnO sample due to its higher exposed area and increased rate of electron-hole generation.     

Structural and optical properties of a radio frequency magnetron-sputtered ZnO thin film with different growth angles

This study introduces optical properties of a columnar structured zinc oxide [ZnO] antireflection coating for solar cells. We obtained ZnO films of columnar structure on glass substrates using a specially designed radio frequency magnetron sputtering system with different growth angles. Field-emission scanning electron microscopy was utilized to check the growth angles of the ZnO films which were controlled at 0°, 15°, and 30°. The film thickness was fixed at 100 nm to get a constant experiment condition. Grain sizes of the ZnO films were measured by X-ray diffraction. A UV-visible spectrometer was used to measure the transmittance and reflectance of the ZnO film columnar structures as a function of the growth angles.     

Efficiency enhancement of non-selenized Cu(In,Ga)Se2 solar cells employing scalable low-cost antireflective coating

In this study, a non-selenized CuInGaSe₂ (CIGS) solar device with textured zinc oxide (ZnO) antireflection coatings was studied. The ZnO nanostructure was fabricated by a low-temperature aqueous solution deposition method. With controlling the morphology of the solution-grown tapered ZnO nanorod coatings, the average reflectance of the CIGS solar device decreased from 8.6% to 2.1%, and the energy conversion efficiency increased from 9.1% to 11.1%. The performance improvement in the CuInGaSe₂ thin-film solar cell was well explained due to the gradual increase of the refractive index between air and the top electrode of solar cell device by the insertion of the ZnO nanostructure. The results demonstrate a potential application of the ZnO nanostructure array for efficient solar device technology.     

Electrochemical deposition of branched hierarchical ZnO nanowire arrays and its photoelectrochemical properties

Branched hierarchical ZnO nanowire arrays are synthesized on fluorine-doped tin oxide (FTO) substrate via a two-step electrochemical deposition process, which involves the electrodeposition of ZnO nanowire arrays on conductive glass substrate, followed by the electrochemical growth of ZnO nanorod branches on the backbones of the primary ZnO nanowires. The formation mechanism of the branched hierarchical nanostructure is discussed. It is demonstrated that coating the primary nanowire arrays with ZnO nanoparticles seed layer plays a key role in synthesising the branched hierarchical ZnO nanostructure. By adjusting the concentration of Zn(CH₃COO)₂ colloid in coating process and the reaction time of the second-step deposition, the density and the length of the secondary nanorod branches in the hierarchical nanostructures can be both varied. Moreover, the photoelectrochemical properties of the dye-sensitized solar cell (DSSC) based on branched hierarchical ZnO nanowire arrays are investigated. Due to the enlargement of the internal surface area within the branched nanostructure photoelectrode, the DSSC consisting of branched hierarchical ZnO nanowire arrays yields a power conversion efficiency of 0.88%, which is almost twice higher than that of the DSSC fabricated using bare ZnO nanowire arrays.     

Direct synthesis of vertically aligned ZnO nanowires on FTO substrates using a CVD method and the improvement of photovoltaic performance

In this work, we report a direct synthesis of vertically aligned ZnO nanowires on fluorine-doped tin oxide-coated substrates using the chemical vapor deposition (CVD) method. ZnO nanowires with a length of more than 30 μm were synthesized, and dye-sensitized solar cells (DSSCs) based on the as-grown nanowires were fabricated, which showed improvement of the device performance compared to those fabricated using transferred ZnO nanowires. Dependence of the cell performance on nanowire length and annealing temperature was also examined. This synthesis method provided a straightforward, one-step CVD process to grow relatively long ZnO nanowires and avoided subsequent nanowire transfer process, which simplified DSSC fabrication and improved cell performance.     

Effect of Al doped ZnO on optical and photovoltaic properties of the p-Cu2O/n-AZO solar cells

Metal oxide thin films have fared so well in the semiconductor industry because of their superior physical, electrical, and optical properties. The applications of these materials in solar cells, biosensors, biomedicine, supercapacitors, photocatalysis, luminous materials, and laser systems are becoming increasingly popular. In this study, the influence of Al concentration on Cu₂O/AZO heterojunction thin films was examined systematically. First, arrays of n-ZnO and AZO rods were produced on an ITO substrate using a hydrothermal technique at 140 °C. Then, using an alkaline cupric lactate solution, a thin films of p-Cu₂O were electrodeposited at 60 °C onto the ZnO arrays. The structure and morphology of the produced materials and the solar cells were studied using X-ray diffraction and scanning electron microscopy. The optical measurements demonstrate a shift in the absorption edge with increasing Al content. Solar cells have been created with a device structure of ITO/ZnO/Cu₂O/Al and ITO/Al-doped ZnO/Cu₂O/Al configurations. The power conversion efficiency (?) of the inorganic solar cell with 6% Al-doped ZnO is ? = 0.282%, which is greater than the ? of the ZnO-based solar cell (? = 0.17%).     

Controllable growth of dendritic ZnO nanowire arrays on a stainless steel mesh towards the fabrication of large area, flexible dye-sensitized solar cells

Well-defined ZnO nanowire (NW) arrays with controlled dendritic structures were successfully built on a stainless steel mesh and utilized as photoanodes for the fabrication of large-area, flexible dye-sensitized solar cells (DSSCs). The dendritic nanostructure proves favorable for the improvement of the overall light conversion efficiency of the DSSC. An optimized etching time for the affixion of ZnO seeds on the ZnO backbone of the dendritic "tree" and the controlled growth conditions of the branch NW are critical to achieve high conversion efficiency solar cells.     

CdSe nanocrystal sensitized ZnO core-shell nanorod array films: Preparation and photovoltaic properties

ZnO/CdSe core-shell nanorod array films were synthesized via a two-step method. ZnO nanorod array films were first grown on a TCO substrate, and then CdSe nanocrystals were deposited on the nanorods to form core-shell structured films. The resulting films were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and UV-vis absorption spectroscopy. Especially, dark-field images and transmission electron diffraction of the TEM were used to study the morphology and the chemical nanostructure of the ZnO/CdSe core-shell nanorods in detail. We investigated the photovoltaic performance of the resulting ZnO/CdSe core-shell nanorod array films as solar cell photoanodes. Parameters, such as the length of the ZnO nanorods, the shell phase structure and the deposition time of the CdSe nanocrystals were found to affect the photovoltaic performance of the solar cell. This study provides a facile method to prepare nanocomposite photoanodes of solar cells, and gives some insight about the fundamental mechanisms that improve the performance.     

Boosting the Performance of ZnO/CdS Core-Shell Nanorod Array-based Solar Cells by ZnS Surface Treatment

With a view to enhancing the efficiency of ZnO/CdS core-shell nanorod array-based semiconductor sensitized solar cells (SSSCs), ZnS surface treatment is envisioned. It is achieved through a thin layer of ZnS being deposited onto ZnO/CdS film by a successive ionic layer adsorption and reaction (SILAR) technique. To ascertain the optimum thickness of ZnS and to enhance the solar cell performance, we have varied the number of SILAR cycles of ZnS deposition. The optimized film is then considered for structural, morphological, and electrochemical studies. The analysis reveals the benefits of ZnS surface treatment on ZnO/CdS core-shell photoelectrodes in terms of an enhancement of solar cell performance of up to 1.54 % from 1.23 %.     

Visible to near-infrared light harvesting in Ag2S nanoparticles/ZnO nanowire array photoanodes

Pronounced absorption in the visible-NIR range of 400-1300 nm is demonstrated in the Ag(2)S nanoparticles (NPs)/ZnO nanowire (NW) array. ZnO NW arrays are grown on indium tin oxide substrates using chemical bath deposition. The Ag(2)S NPs are sequentially formed on the ZnO NWs through sonochemical synthesis. Structural characterizations indicate the slight deconstruction of surface of ZnO NWs during Ag(2)S NPs formation. By employing polysulfide electrolyte, short-circuit current (J(sc)), open-circuit voltage and therefore the efficiency of the Ag(2)S NP-sensitized ZnO NW solar cell are improved with increasing the initial sulfur concentration in the sulfur-polysulfide electrolyte. The Ag(2)S NP-sensitized ZnO NW solar cell shows a conversion efficiency of 0.49% with a superior J(sc) of ~13.7 mA cm(-2) under AM 1.5 illumination at 100 mW cm(-2). Incident photon conversion efficiency measurements reveal that Ag(2)S NPs contribute to 33.4% and 65.2% of J(sc) in the wavelength ranges of 400-700 nm and 700-1300 nm, respectively.     

Nanostructured Al-ZnO/CdSe/Cu2O ETA solar cells on Al-ZnO film/quartz glass templates

ABSTRACT: The quartz/Al-ZnO film/nanostructured Al-ZnO/CdSe/Cu2O extremely thin absorber solar cell has been successfully realized. The Al-doped ZnO one-dimensional nanostructures on quartz templates covered by a sputtering Al-doped ZnO film was used as the n-type electrode. A 19- to 35-nm-thin layer of CdSe absorber was deposited by radio frequency magnetron sputtering, coating the ZnO nanostructures. The voids between the Al-ZnO/CdSe nanostructures were filled with p-type Cu2O, and therefore, the entire assembly formed a p-i-n junction. The cell shows the energy conversion efficiency as high as 3.16%, which is an interesting option for developing new solar cell devices.PACS: 88.40.jp; 73.40.Lq; 73.50.Pz.     

Facile solution growth of vertically aligned ZnO nanorods sensitized with aqueous CdS and CdSe quantum dots for photovoltaic applications

Vertically aligned single crystalline ZnO nanorod arrays, approximately 3 μm in length and 50-450 nm in diameter are grown by a simple solution approach on a Zn foil substrate. CdS and CdSe colloidal quantum dots are assembled onto ZnO nanorods array using water-soluble nanocrystals capped as-synthesized with a short-chain bifuncional linker thioglycolic acid. The solar cells co-sensitized with both CdS and CdSe quantum dots demonstrate superior efficiency compared with the cells using only one type of quantum dots. A thin Al2O3 layer deposited prior to quantum dot anchoring successfully acts as a barrier inhibiting electron recombination at the Zn/ZnO/electrolyte interface, resulting in power conversion efficiency of approximately 1% with an improved fill factor of 0.55. The in situ growth of ZnO nanorod arrays in a solution containing CdSe quantum dots provides better contact between two materials resulting in enhanced open circuit voltage.