Atom transfer radical polymerization of acrylonitrile

Iron(II) chloride coordinated by succinic acid was first used as the catalyst in 2‐chloropropionitrile‐initiated atom transfer radical polymerization (ATRP) of acrylonitrile. N,N‐dimethylformamide was used as a solvent to improve the solubility of the ligand. An iron(II) chloride to succinic acid ratio of 0.5 not only gives the best control of molecular weight and its distribution but also provides rather rapid reaction rate. Effects of solvent on polymerization of acrylonitrile were also investigated. The induction period is shorter in N,N‐dimethylformamide than in propylene carbonate and toluene and the rate of the polymerization in N,N‐dimethylformamide is fastest. The molecular weight of polyacrylonitrile agrees reasonably well with the theoretical molecular weight of N,N‐dimethylformamide. The rate of polymerization increases and the induction period becomes shorter with increasing polymerization temperature, and the apparent activation energy was calculated to be 56.5 kJ mol^?1. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1050–1054, 2006     

Effects of the solvent polarity on the atom transfer radical polymerization of methyl methacrylate initiated by 4‐(chloromethyl)phenyltrimethoxysilane

The controllability of the atom transfer radical polymerization of methyl methacrylate in the polar solvent N,N‐dimethylformamide and the nonpolar solvent xylene with 4‐(chloromethyl)phenyltrimethoxysilane as an initiator and with CuCl/2,2′‐bipyridine and CuCl/4,4′‐di(5‐nonyl)‐2,2′‐bipyridine as catalyst systems was studied. Gel permeation chromatography analysis established that in the nonpolar solvent xylene, much better control of the molecular weight and polydispersity of poly(methyl methacrylate) was achieved with the CuCl/4,4′‐di(5‐nonyl)‐2,2′‐bipyridine catalyst system than with the CuCl/2,2′‐bipyridine as catalyst system. In the polar solvent N,N‐dimethylformamide, unlike in xylene, the polymerization was more controllable with the CuCl/2,2′‐bipyridine catalyst system than with the CuCl/4,4′‐di(5‐nonyl)‐2,2′‐bipyridine catalyst system. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2751–2754, 2007     

Reverse atom transfer radical polymerization of acrylonitrile

FeCl₃ coordinated by succinic acid was used as the catalyst for the first time in azobisisobutyronitrile‐initiated reverse atom transfer radical polymerization of acrylonitrile (AN). N,N‐dimethylformamide (DMF) was used as a solvent to improve the solubility of the ligand. A FeCl₃ to succinic acid ratio of 0.5 not only gives the best control of molecular weight and its distribution but also provides rather rapid reaction rate. Effects of different solvents on polymerization of AN were also investigated. The rate of the polymerization in DMF is faster than that in propylene carbonate and toluene. The molecular weight of polyacrylonitrile agrees reasonably well with the theoretical molecular weight in DMF. The rate of polymerization increases with increasing the polymerization temperature, and the apparent activation energy was calculated to be 64.8 kJ mol^?1. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 32–36, 2006     

An iron‐based reverse ATRP process for the living radical polymerization of acrylonitrile

A hexa‐substituted ethane thermal iniferter, diethyl‐2,3‐dicyano‐2,3‐di(p‐tolyl) succinate (DCDTS), was firstly used as the initiator in the reverse atom transfer radical polymerization (RATRP) of acrylonitrile. FeCl₃ coordinated by isophthalic acid (IA) was used as the catalyst in this system. The polymerization in N,N‐dimethylformamide not only shows the best control of molecular weight and its distribution but also provides rather rapid reaction rate with the ratio of [AN] : [DCDTS] : [FeCl₃] : [IA] at 500 : 1 : 2 : 4. The polymers obtained were end‐functionalized by chlorine atom, and they were used as macroinitiators to proceed the chain extension polymerization in the presence of FeCl₂/IA catalyst system via a conventional ATRP process and polyacrylonitrile obtained was with M_n = 39,260, PDI = 1.25. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Reverse atom‐transfer radical polymerization of acrylonitrile catalyzed by FeCl3/iminodiacetic acid

FeCl₃ coordinated by iminodiacetic acid (IMA) was Changed used for the first time as the catalyst in azobisisobutyronitrile‐initiated reverse atom‐transfer radical polymerization (ATRP) of acrylonitrile (AN). An FeCl₃ to IMA ratio of 1:2 not only gave the best control of molecular weight and its distribution but also provided a rather rapid reaction rate. The effects of solvents on the polymerization of AN were also investigated. The rate of the polymerization in N,N‐dimethylformamide (DMF) was faster than in propylene carbonate or toluene. The molecular weight of polyacrylonitrile agreed reasonably well with the theoretical molecular weight in DMF. The rate of polymerization increased with increasing polymerization temperature and the apparent activation energy was calculated to be 54.8 kJ mol⁻¹. The reverse ATRP of AN did not show obvious living characteristics with CuCl₂ instead of FeCl₃. Copyright © 2005 Society of Chemical Industry     

Atom transfer radical polymerization of styrene with 2‐(1‐bromoethyl)‐anthraquinone as an initiator

2‐(1‐Bromoethyl)‐anthraquinone (BEAQ) was successfully used as an initiator in the atom transfer radical polymerization of styrene with CuBr/N,N,N′,N′,N″‐pentamethyldiethylenetriamine as the catalyst at 110°C. The polymerizations were well controlled with a linear increase in the molecular weights (M_n's) of the polymers with monomer conversion and relatively low polydispersities (1.1 < weight‐average molecular weight (M_w)/M_n < 1.5) throughout the poly merizations. The resultant polystyrene thus possessed one chromophore moiety (2‐ethyl‐anthraquinone) at the α end and one bromine atom at the ω end, both from the initiator BEAQ. The intensity of UV absorptions of the resultant polymers decreased with increasing molecular weights of the polymers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2081–2085, 2006     

Reverse atom transfer radical polymerization of stearyl methacrylate using 2,2′‐azobisisobutyronitrile as the initiator

The living/controlled radical polymerization of stearyl methacrylate was carried out with a conventional radical initiator (2,2′‐azobisisobutyronitrile) in N,N‐dimethylformamide in the presence of a 2,2′‐bipyridine complex of hexakis(N,N‐dimethylformamide)iron(III) perchlorate. The polymerization mechanism was thought to proceed through a reverse atom transfer radical polymerization. The molecular weights of resulting poly(stearyl methacrylate) increased with conversion, and the resulting molecular weight distributions were quite narrow. The rates of polymerization exhibited first‐order kinetics with respect to the monomer. A probable reaction mechanism for the polymerization system is postulated to explain the observed results. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1236–1245, 2002     

Fe‐mediated SET‐LRP of MMA and St in the presence of air

In this work, well‐defined homopolymers of methyl methacrylate (PMMA) and styrene (PSt) were prepared via single‐electron‐transfer living radical polymerization using CCl₄ as initiator and Fe(0)/N, N, N′,N′‐tetramethyl‐1,2‐ethanediamine as catalyst. The polymerization was conducted at 25 °C in N,N‐dimethylformamide in the presence of air. It proceeded in a ‘living’ manner, as indicated by the first‐order kinetics behavior, and the linear increase of the number‐average molecular weight (M_{n, GPC}) with conversion was close to the theoretical M_{n, theory}. Solvent and additives have a profound effect on the polymerization. In addition, the PMMA and PSt obtained remained of low dispersity. The chain‐end functionality of the obtained homopolymer of PMMA was characterized by proton nuclear magnetic resonance. A block copolymer of P(MMA‐block‐St) was achieved by using the obtained PMMA as macroinitiator. The living characteristics were further demonstrated by chain extension experiments. Copyright © 2012 Society of Chemical Industry     

Reverse atom transfer radical polymerization of methyl methacrylate in different solvents

The reverse atom transfer radical polymerization of methyl methacrylate was investigated in different solvents: xylene, N,N‐dimethylformamide, and pyridine. The polymerizations were uncontrolled, using 2,2′‐bipyridine as a ligand in xylene and pyridine because the catalyst (CuBr₂/2,2′‐bipyridine complex) had poor solubility in the xylene system. In the pyridine system, the solubility of the catalyst increased, but the solvent could complex with CuBr₂, which influenced the control of the polymerization. In the N,N‐dimethylformamide system, the catalyst could be dissolved in the solvent completely, but the ? N(CH₃)₂ group in N,N‐dimethylformamide could also complex with CuBr₂, so the polymerization could not be well controlled. The ligand of 4,4′‐di(5‐nonyl)‐2,2′‐bipyridine was also investigated in xylene; the introduction of the ? CH(C₄H₉)₂ group enabled the CuBr₂/4,4′‐di(5‐nonyl)‐2,2′‐bipyridine complex to easily dissolve in xylene, and the polymerizations were well controlled. The number‐average molecular weight increased linearly with the monomer conversion from 4280 to 14,700. During the whole polymerization, the polydispersities were quite low (1.07–1.10). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

ICAR ATRP of methyl methacrylate catalyzed by FeCl3·6H2O/succinic acid

In this work, methyl methacrylate (MMA) was polymerized by initiator for continuous activator regeneration (ICAR) atom transfer radical polymerization (ATRP) method to obtain low molecular weight living polymers. The ATRP initiator was ethyl 2‐bromoisobutyrate, the catalyst ligand complex system was FeCl₃·6H₂O/succinic acid, and the conventional radical initiator 2,2′‐azobisisobutyronitrile was used as a thermal radical initiator. Polymers with controlled molecular weight were obtained with ppm level of Fe catalyst complex at 90°C in N,N‐dimethylformamide. The polymer was characterized by nuclear magnetic resonance (NMR). The molecular weight and molecular weight distribution of the obtained poly (methyl methacrylate) were measured by gel permeation chromatography method. The kinetics results indicated that ICAR ATRP of MMA was a “living”/controlled polymerization, corresponding to a linear increase of molecular weights with the increasing of monomer conversion and a relatively narrow polydispersities index. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Reverse atom transfer radical polymerization of acrylonitrile under microwave irradiation

Reverse atom transfer radical polymerization was first used to successfully synthesize polyacrylonitrile under microwave irradiation. FeCl₃, coordinated by isophthalic acid, was used as the catalyst, and 2,2′‐azobisisoheptonitrilewas used as the initiator. N,N‐Dimethylformamide was used as the solvent to improve the solubility of the ligand. Under the same experimental conditions, the apparent rate constant under microwave irradiation was higher than that under conventional heating. The polymerization not only showed the best control of the molecular weight and its distribution but also provided a rather rapid reaction rate with the [acrylonitrile]/[2,2′‐azobisisoheptonitrile]/[FeCl₃]/[isophthalic acid] ratio of 300 : 1 : 1 : 2. The polymers obtained were used as macroinitiators to initiate the chain extension and successfully synthesize acrylonitrile polymers with a molecular weight higher than 50,000 and a narrow polydispersity as low as 1.30. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Formation of SBS thermoplastic block copolymer using hexamethyleneimine alkenyl lithium (N‐Li) initiator

Styrene and butadiene block copolymers (SBS) end functionalized with amino group at the initiating chain ends were synthesized using hexamethyleneimine alkenyl lithium (N‐Li) as initiator, tetrahydrofuran (THF) as polar modifier, and cyclohexane as solvent. By attaching a few number of butadiene molecules to N‐lithium hexamethyleneimine, a new N‐Li initiator that can effectively initiate the polymerization of SBS was obtained. ¹H NMR spectrums of the N‐Li initiator terminated by ethanol, end functionalized polystyrene, and SBS block copolymer proved the structure of N‐Li and its ability to initiate the polymerization of styrene and SBS block copolymer. Kinetics studies suggested that the polymerization rate of styrene in the first block reached the maximum when the ratio of THF/Li was increased to 5, while further increase of the ratio of THF/Li could not improve the polymerization rate. The molecular weight distribution (MWD) of SBS initiated by N‐Li varied with the ratio of THF/Li. The vinyl content of polybutadiene block increased by improving the ratio of THF/Li, while the content of cis‐1,4 and trans‐1,4 structures decreased. The vinyl content of end functionalized SBS was somewhat higher than that of SBS initiated by classical n‐butyllithium when other condition was the same. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 81–88, 2006     

Synthesis and characterization of poly(vinyl chloride‐co‐vinyl acetate)‐graft‐poly[(meth)acrylates] by atom transfer radical polymerization

The graft polymerization of methyl methacrylate and butyl acrylate onto poly(vinyl chloride‐co‐vinyl acetate) with atom transfer radical polymerization (ATRP) was successfully carried out with copper(I) thiocyanate/N,N,N′,N′,N″‐pentamethyldiethylenetriamine and copper(I) chloride/2,2′‐bipyridine as catalysts in the solvent N,N‐dimethylformamide. For methyl methacrylate, a kinetic plot of ln([M]₀/[M]) (where [M]₀ is the initial monomer concentration and [M] is the monomer concentration) versus time for the graft polymerization was almost linear, and the molecular weight of the graft copolymer increased with increasing conversion, this being typical for ATRP. The formation of the graft polymer was confirmed with gel permeation chromatography, ¹H‐NMR, and Fourier transform infrared spectroscopy. The glass‐transition temperature of the copolymer increased with the concentration of methyl methacrylate. The graft copolymer was hydrolyzed, and its swelling capacity was measured. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 183–189, 2005     

Atom transfer radical polymerization of lauryl methacrylate

The atom transfer radical polymerization (ATRP) of lauryl methacrylate (LMA) with an ethyl 2‐bromobutyrate/CuCl/N,N,N′,N″,N″‐pentamethyldiethylenetriamine initiation system was successfully carried out in toluene, and poly(lauryl methacrylate) with a low polydispersity (1.2 < weight‐average molecular weight/number‐average molecular weight < 1.5) was obtained. Plots of ln ([M])₀/([M]) versus time and plots of the molecular weight versus conversion showed a linear dependence, indicating a constant number of propagating species throughout the polymerization. The rate of polymerization was 0.56‐order with respect to the concentration of the initiator and 1.30‐order with respect to the concentration of the Cu(I) catalyst. In addition, the effect of the solvent on the polymerization was investigated, and the thermodynamic data and activation parameters for the solution ATRP of LMA were reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1117–1125, 2003     

Synthesis and characterization of soluble hyperbranched polymer via initiator‐fragment incorporation radical polymerization of divinylbenzene with dimethyl 2,2′‐azobisisobutyrate

The homopolymerization of divinylbenzene (DVB) as an excellent crosslinker (0.20 mol/L) with dimethyl 2,2′‐azobisisobutyrate (MAIB) proceeded homogeneously without any gelation at 80°C in benzene when the MAIB concentrations as high as 0.30–0.50 mol/L were used, yielding soluble polymers. In the polymerization at the concentrations of [DVB] = 0.20 mol/L and [MAIB] = 0.50 mol/L, the polymer yield increased with time and leveled off over 90 min. The molecular weight and molecular weight distribution increased with polymer yield. The vinyl groups of DVB were observed to be almost completely consumed in about 80 min, by FT near‐IR spectroscopic analysis. The homogeneous polymerization system involved ESR‐observable polymer radical, the concentration of which increased with time up to 3.4 × 10^?5 mol/L. The polymer formed in the polymerization for 2 h consisted of 46 mol % of DVB unit and 54 mol % of the methoxycarbonylpropyl group as MAIB fragment, indicating that an initiator‐fragment incorporation radical polymerization proceeds in the present polymerization. The polymer was soluble in benzene, tetrahydrofuran, ethyl acetate, chloroform, acetone, and N,N‐dimethylformamide, while it was insoluble in n‐hexane, acetonitrile, dimethyl sulfoxide, methanol, and water. The results of the multiangle laser light scattering and viscometric measurements revealed that the individual polymer molecules were formed as hyperbranched polymer nanoparticles. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 664–670, 2006     

Effects of solvent basicity on free radical polymerizations of N,N′‐bismaleimide‐4,4′‐diphenylmethane initiated by barbituric acid

The polymerizations of N,N′‐bismaleimide‐4,4′‐diphenylmethane (BMI) initiated by barbituric acid (BTA) carried out in a variety of solvents at 130°C were studied. The nitrogen‐containing cyclic solvents such as N‐methyl‐2‐pyrrolidinone acted as a catalyst to promote the formation of the three‐dimensional crosslinked network structure. By contrast, the polymerization in a cyclic solvent that did not contain nitrogen such as γ‐butyrolactone resulted in nil gel content. The higher the solvent basicity, the larger the amount of insoluble polymer species formed. The molar ratio of BTA to BMI also played an important role in the polymerizations. The resultant polymers, presumably having a hyper‐branched structure, exhibited much narrower molecular weight distributions than those prepared by conventional free radical polymerizations. The BMI polymerizations using BTA as the initiator could not be adequately described by conventional free radical polymerization mechanisms. A polymerization mechanism that took into account the generation of a ketone radical pair between BTA and BMI and the subsequent initiation, propagation and termination reactions was proposed. It was concluded that the nitrogen‐containing cyclic solvents were capable of participating in the ketone radical pair formation process, thereby increasing the extent of polymer crosslinking reactions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

High molecular weight hydrophilic functional copolymers by free‐radical copolymerization of acrylamide and of N‐acryloylmorpholine with N‐acryloxysuccinimide: Application to the synthesis of a graft copolymer

Free‐radical solution copolymerization of acrylamide (AAm) and of a disubstituted acrylamide derivative, N‐acryloylmorpholine (NAM), with N‐acryloxysuccinimide (NAS) was investigated with the aim to obtain a copolymer of at least 100,000 g mol^?1. Different polymerization conditions likely to increase the molecular weight were studied such as monomer and initiator concentrations, temperature, and nature of the solvent. The molecular weights were determined by SEC using a light‐scattering detector. The grafting of end‐functionalized polysaccharide chains onto such high molecular weight poly(NAM‐co‐NAS) was performed and a graft copolymer bearing a high number of saccharidic branches was obtained. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1808–1816, 2003     

Synthesis and characterization of water soluble poly(N‐acetyl)iminoethylene and poly(ethyleneimine) by ion‐exchanged clay montmorillonite

The cationic polymerization of 2‐méthyl‐2‐oxazoline was carried out at 0°C in acetonitrile using an acid‐exchanged montmorillonite as acid solid ecocatalyst (Maghnite‐H⁺). The effect of the amount of catalyst, solvent, and times of polymerization on yield and viscosity of polymer was studied. A typical reaction product (PMOX) was analyzed by infrared and nuclear magnetic resonance spectroscopy as well as by gel‐permeation chromatography and MALDI‐TOF MS. The polymers presented similar spectrometric results and narrow molecular weight distribution. The poly(N‐acetyl)iminoethylene was hydrolyzed in acid medium obtaining a linear poly(ethyleneimine). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:3741–3750, 2006     

Organic–inorganic composite materials as photoinitiator for controlling/living polymerization

Titanium dioxide (TiO₂)/graphitic carbon nitride (g‐C₃N₄) composites were first used as photoinitiator for photochemically mediated controlled/living polymerization of methyl methacrylate. The polymerization was successfully carried out in polyethylene glycol at room temperature with FeCl₃·6H₂O/N,N,N ′,N ′,N ″‐pentamethyldiethylenetriamine as complex catalyst and ethyl 2‐bromoisobutyrate as initiator in this case. A pseudo‐first‐order dependence of the monomer concentration on the polymerization time was observed. TiO₂/g‐C₃N₄ was verified to be an efficient photoinitiator. The polymerization was controlled to produce poly(methyl methacrylate) with narrow molecular weight distribution and controlled number average molecular weight (M_n,GPC). The M_n,GPC matched well with the theoretical values when using both UV and sunlight irradiation as light source. The effects of reaction conditions on the polymerization were investigated. The polymerization could be started and stopped through periodically switching on/off the light. The living nature was further supported by the chain extension experiments. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42891.     

Synthesis of polyacrylonitrile via reverse ATRP initiated by 1,1,2,2‐tetraphenyl‐1,2‐ethanediol/CuCl2/2,2′‐bipyridine

The reverse atom‐transfer radical polymerization (RATRP) technique using CuCl₂/2,2′‐bipyridine (bipy) complex as a catalyst was applied to the living‐radical polymerization of acrylonitrile (AN). 1,1,2,2‐Tetraphenyl‐1,2‐ethanediol (TPED) was first used as the initiator in this copper‐based RATRP initiation system. A CuCl₂ to bipy ratio of 0.5 not only gives the best control of molecular weight and its distribution, but also provides rather rapid reaction rate. The rate of polymerization increases with increasing the polymerization temperature, and the apparent activation energy was calculated to be 53.2 kJ mol^?1. Because the polymers obtained were end‐functionalized by chlorine atoms, they were used as macroinitiators to proceed the chain extension polymerization in the presence of CuCl/bipy catalyst system via a conventional ATRP process. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3529–3533, 2007