Poly(1,3‐disila‐1,3‐diphenyl‐2‐oxaindane)‐diphenylsiloxane‐poly(dimethylsiloxane) block copolymers

The heterofunctional condensation of 1,3‐dichloro‐1,3‐disila‐1,3‐diphenyl‐2‐oxaindane with dihydroxydiphenylsilane at various ratios of initial compounds in the presence of amines was carried out, and α,ω‐dihydroxy(1,3‐disila‐1,3‐diphenyl‐2‐oxaindane)‐diphenylsiloxane oligomers with various degrees of condensation were obtained. Corresponding block copolymers were obtained by heterofunctional polycondensation of synthesized α,ω‐dihydroxy(1,3‐disila‐1,3‐diphenyl‐2‐oxaindane)‐diphenylsiloxane oligomers with α,ω‐dichlorodimethylsiloxanes in the presence of amines. Thermogravimetry, gel permeation chromatography, differential scanning calorimetry, and wide‐angle X‐ray analysis were carried out on the synthesized block coplymers. Differential scanning calorimetry and wide‐angle X‐ray studies of these copolymers showed that their properties were determined by the ratio of the lengths of the flexible linear poly(dimethylsiloxane) and rigid poly(1,3‐disila‐1,3‐diphenyl‐2‐oxaindane)‐diphenylsiloxane fragments in the main macromolecular chain. Two‐phase systems were obtained with specific flexible and rigid fragment length values in synthesized block copolymers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3462–3467, 2006     

Poly(1,3‐disila‐1,3‐diphenyl‐2‐oxaindane)– poly(dimethylsiloxane) block copolymers

The hydrolytic condensation of 1,3‐dichloro‐1,3‐disila‐1,3‐diphenyl‐2‐oxaindane under neutral conditions produced α'ω‐dihydroxy‐1,3‐disila‐1,3‐diphenyl‐2‐oxaindane (polymerization degree ≈ 4). The homofunctional condensation of α'ω‐dihydroxy‐1,3‐disila‐1,3‐diphenyl‐2‐oxaindane in a toluene solution and in the presence of activated carbon was performed, and dihydroxy‐containing oligomers with various degrees of condensation were obtained. Through the heterofunctional condensation of dihydroxy‐containing oligomers with α'ω‐dichlorodimethylsiloxanes in the presence of amines, corresponding block copolymers were obtained. Gel permeation chromatography, differential scanning calorimetry, thermomechanical analysis, thermogravimetry, and wide‐angle roentgenography investigations were carried out. Differential scanning calorimetry and roentgenography studies of the block copolymers showed that their properties were determined by the ratio of the lengths of the flexible and linear poly(dimethylsiloxane) and rigid poly(1,3‐disila‐1,3‐diphenyl‐2‐oxaindane) fragments in the macromolecular chain. At definite values of the lengths of the flexible and rigid fragments, a microheterogeneous structure was observed in the synthesized block copolymers. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1409–1417, 2002; DOI 10.1002/app.10335     

Synthesis and investigation of the properties of poly(phenyl‐α‐naphthylsilylene)–dimethylsilylene copolymers

A Wurtz‐type reductive coupling reaction of dichlorophenyl‐α‐naphthylsilane was carried out in a mixture of toluene and o‐xylene in the presence of sodium and a catalytic amount of mercury; α,ω‐dichlorophenyl‐α‐naphthylsilylenes of various degrees of polymerization were obtained. Through the hydrolysis of α,ω‐dichlorophenyl‐α‐naphthylsilylenes, corresponding dihydroxy compounds were obtained. The heterofunctional polycondensation of α,ω‐dihydroxyphenyl‐α‐naphthylsilylenes with α,ω‐dichlorodimethylsilylenes was performed both without amines and in the presence of amines. Heterofunctional polycondensation without amines did not proceed with the formation of high molecular weight compounds because the cleavage of both ? Si? Si? and ?Si? O? Si? bonds took place during condensation. In the presence of amines, polysilylene–silylene copolymers were obtained. The synthesized copolymers were investigated with gel permeation chromatography, differential scanning calorimetry, roentgenography, and thermogravimetry. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1047–1056, 2002     

Temperature influence on the behavior of polysulfone‐b‐poly(alkylene oxide)‐b‐poly(dimethylsiloxane) triblock copolymers in a selective solvent

Triblock copolymers containing polysulfone, poly(alkylene oxide), and poly(dimethylsiloxane) segments were obtained by addition of preformed α,ω‐bis(hydrogensilyl) poly(dimethylsiloxane) oligomers to alyl end‐capped poly(alkylene oxide)‐b‐polysulfone. Viscometric and UV absorption measurements were carried out in dilute 1,2‐dichlorethane solutions, in the temperature range of 20–75°C. The specific interactions exhibited by the block copolymers in a selective solvent are influenced by the copolymer composition and temperature. The results point to a conformational transition phenomenon, located around 55°C, which is attributed to the transition from a segregated to a pseudo‐Gaussian conformation through a compressed‐segregated conformation. POLYM. ENG. SCI., 57:114–118, 2017. © 2016 Society of Plastics Engineers     

Synthesis and characterization of copolymers based on poly(butylene terephthalate) and ethylene oxide‐poly(dimethylsiloxane)‐ethylene oxide

A series of thermoplastic elastomers based on ethylene oxide‐poly(dimethylsiloxane)‐ethylene oxide (EO‐PDMS‐EO), as the soft segment, and poly(butylene terephthalate) (PBT), as the hard segment, were synthesized by catalyzed two‐step, melt transesterification reaction of dimethyl terephthalate (DMT) with 1,4‐butanediol (BD) and α,ω‐dihydroxy‐(EO‐PDMS‐EO). Copolymers with a content of hard PBT segments between 40 and 90 mass % and a constant length of the soft EO‐PDMS‐EO segments were prepared. The siloxane prepolymer with hydrophilic terminal EO units was used to improve the miscibility between the polar comonomers, DMT and BD, and the nonpolar PDMS. The molecular structure and composition of the copolymers were determined by ¹H‐NMR spectroscopy, whereas the effectiveness of the incorporation of α,ω‐dihydroxy‐(EO‐PDMS‐EO) into the copolymer chains was verified by chloroform extraction. The effects of the structure and composition of the copolymers on the melting temperatures and the degree of crystallinity, as well as on the thermal degradation stability and some rheological properties, were studied. It was demonstrated that the degree of crystallinity, the melting and crystallization temperatures of the copolymers increased with increasing mass fraction of the PBT segments. The thermal stability of the copolymers was lower than that of PBT homopolymer, because of the presence of thermoliable ether bonds in the soft segments. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of poly(ester ether siloxane)s

A series of novel thermoplastic elastomers based on ABA‐type triblock prepolymers, poly[(propylene oxide)–(dimethylsiloxane)–(propylene oxide)] (PPO‐PDMS‐PPO), as the soft segments, and poly(butylene terephthalate) (PBT), as the hard segments, was synthesized by catalyzed two‐step melt transesterification of dimethyl terephthalate (DMT) with 1,4‐butanediol (BD) and α,ω‐dihydroxy‐(PPO‐PDMS‐PPO) (M?_n = 2930 g mol^?1). Several copolymers with a content of hard PBT segments between 40 and 60 mass% and a constant length of the soft PPO‐PDMS‐PPO segments were prepared. The siloxane‐containing triblock prepolymer with hydrophilic terminal PPO blocks was used to improve the compatibility between the polar comonomers, i.e. DMT and BD, and the non‐polar PDMS segments. The structure and composition of the copolymers were examined using ¹H NMR spectroscopy, while the effectiveness of the incorporation of α,ω‐dihydroxy‐(PPO‐PDMS‐PPO) prepolymer into the copolyester chains was controlled by chloroform extraction. The effect of the structure and composition of the copolymers on the transition temperatures (T_m and T_g) and the thermal and thermo‐oxidative degradation stability, as well as on the degree of crystallinity, and some rheological properties, were studied. Copyright © 2006 Society of Chemical Industry     

Synthesis,characterization, and thermal properties of alternate copolymers containing N,N′‐bis(diphenylsilyl)tetraphenylcyclodisilazane

Hexamethyldisilazane was used as the starting material to synthesize N,N′‐bis(hydroxydiphenylsilanyl)tetraphenylcyclodisilazane (BHPTPC). By condensation polymerization of BHPTPC with α,ω‐bis(dialkylamino)dimethylsiloxane, a series of alternate copolymers containing N,N′‐bis(diphenylsilyl)tetraphenylcyclodisilazane was synthesized. GPC studies show that the highest molecular weight was obtained at a ratio of 1.005 : 1 (BHPTPC: α,ω‐bis(dimethyl amino)dimethylsiloxane). Data of DSC indicate that the temperature of glass transition (T_g) and temperature of melting point (T_m) decreased with the increasing of dimethylsiloxane segments units. Three stages of degradation were found in the thermogravimetric analysis curves. The activation energy of the copolymer (with m = 2, 3, and 7) was calculated by using Flynn–Wall–Ozawa method. The activation energy of the copolymer with m = 2, 3, and 7 at second stage is 214, 211, and 184 kJ/mol, respectively. Isothermal gravimetric analysis shows that for the same temperature and the same time, the weight loss of the alternate copolymer was greatly less than that of common polydimethylsiloxane. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 611–617, 2007     

Synthesis and properties of block and graft waterborne polyurethane modified with α,ω‐bis(3‐(1‐methoxy‐2‐hydroxypropoxy)propyl)polydimethylsiloxane and α‐N,N‐dihydroxyethylaminopropyl‐ω‐butylpolydimethylsiloxane

In this study, α,ω‐bis(3‐(1‐methoxy‐2‐hydroxypropoxy)propyl)polydimethylsiloxane and α‐N,N‐dihydroxyethylaminopropyl‐ω‐butylpolydimethylsiloxane were used to prepare block and graft waterborne polyureathane–polysiloxane copolymer dispersions. α,ω‐bis(3‐(1‐methoxy‐2‐hydroxypropoxy)propyl)polydimethylsiloxane was synthesized by hydrosilylation, methoxylation and equilibrium reactions; α‐N,N‐dihydroxyethylaminopropyl‐ω‐butylpolydimethylsiloxane was synthesized via hydroxyl protection, alkylation, anionic ring‐opening polymerization, hydrosilylation, and deprotection. Block and graft waterborne polyurethane–polysiloxane copolymer dispersions were prepared by the reaction of poly(propylene glycol) (PPG), toluene diisocyanate (TDI), 2,2‐dimethylol propionic acid (DMPA), 1,4‐butanediol (BDO), α,ω‐bis(3‐(1‐methoxy‐2‐hydroxypropoxy)propyl)polydimethylsiloxane, and α‐N,N‐dihydroxy‐ethylaminopropyl‐ω‐butylpolydimethylsiloxane. The water absorption of block and graft waterborne polyurethane–polysiloxane copolymer films decreased from 163.9 to 40.2% and 17.3%, respectively, when percent of polysiloxane (w/w) increased from 0 to 5%, and the tensile strength of the block waterborne polyurethane–polysiloxane copolymer films decreased while the tensile strength of graft waterborne polyurethane–polysiloxane copolymer films increased with increase of percent of polysiloxane. For graft waterborne polyurethane–polysiloxane films, the tensile strength would decrease when percent of polysiloxane was more than 3%. POLYM. ENG. SCI., 54:805–811, 2014. © 2013 Society of Plastics Engineers     

Synthesis and characterization of novel urethane‐siloxane copolymers with a high content of PCL‐PDMS‐PCL segments

Novel polyurethane copolymers derived from 4,4′‐methylenediphenyl diisocyanate (MDI), 1,4‐butanediol (BD) and α,ω‐dihydroxy‐[poly(caprolactone)‐poly (dimethylsiloxane)‐poly(caprolactone)] (α,ω‐dihydroxy‐(PCL‐PDMS‐PCL); = 6100 g mol^?1) were synthesized by a two‐step polyaddition reaction in solution. In the synthesis of the polyurethanes, the PCL blocks served as a compatibilizer between the nonpolar PDMS blocks and the polar comonomers, MDI and BD. The synthesis of thermoplastic polyurethanes (TPU) with high soft segment contents was optimized in terms of the concentrations of the reactants, the molar ratio of the NCO/OH groups, and the time and temperature of the polyaddition reaction. The structure, composition, and hard MDI/BD segment length of the synthesized polyurethane copolymers were determined by ¹H, ¹³C‐NMR, and two‐dimensional correlation (COSY, HSQC, and HMBC) spectroscopy, while the hydrogen bonding interactions in the copolymers were analyzed by FT‐IR spectroscopy. The influence of the reaction conditions on the structure, molecular weight, thermal, and some physical properties was studied at constant composition of the reaction mixture. A change in the molar ratio of the NCO/OH groups and the reaction conditions modified not only the molecular weight of the synthesized polyurethanes, but also the microstructure and therefore the thermal and physical properties of the copolymers. It was demonstrated that only PCL segments with high soft segment contents crystallize, thereby showing spherulitic morphology. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Radical copolymerization of methyl α-acyloxyacrylates with some vinyl monomers

Radical copolymerization of some methyl α-acyloxyacrylates and vinyl monomers has been studied using an azo initiator in benzene at 60 °C. It is found that the Q and e values of methyl α-acyloxyacrylates are in the ranges 0.47–1.65 and 0.51–0.99, respectively, and the relative reactivity of the acrylates towards the propagating radicals of styrene in copolymerization is correlated to the modified Taft equation considering the steric and electronic effects. Copolymerization of methyl α-acetoxyacrylate and vinyl monomers shows that the relative reactivity of the vinyl monomers for the attack of poly (methyl α-acetoxyacrylate) radical tends to increase with increasing Q values of the vinyl monomers. © 1999 Society of Chemical Industry     

Arylenecyclosiloxane–dimethylsiloxane copolymers

The heterofunctional condensation reaction of 1,4‐bis(phenyldichlorosilyl)benzene with dihydroxydiphenylsilane at a 1:4 ratio of initial compounds in the presence of pyridine was investigated and tetrakis(hydroxydiphenylsiloxy)‐1,4‐bis(phenylsilyl)benzene was obtained. The heterofunctional condensation of the tetrakis(hydroxydiphenylsiloxy)‐1,4‐bis(phenylsilyl)benzene with organotrichlorosilanes at a 1:2 ratio of initial compounds in the presence of pyridine produced dichloro‐containing arylenecyclosiloxanes. The dichloro‐containing arylenecyclosiloxanes were obtained in one stage by successive heterofunctional condensation of 1,4‐bis(dichlorophenylsilyl)benzene with dihydroxydiphenylsilane and organotrichlorosilanes in a 1:4:2 ratio in the presence of pyridine. It was established that the yields of dichloro‐containing products were lower. Hydrolysis of dichloroarylenecyclosiloxanes in a neutral condition produced corresponding dihydroxy compounds. Heterofunctional polycondensation of dicloro(dihydroxy)arylenecyclosiloxanes with α,ω‐dihydroxy(bisdimethylamino)dimethylsiloxanes was used to obtain arylenecyclosiloxane‐dimethylsiloxane copolymers. Thermogravimetric, thermomechanical, and roentgenographic investigations of the synthesized copolymers were carried out. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3142–3148, 2001     

Comb‐type methylsiloxane copolymers with diorganosilylene fragments as a lateral group

The catalytic dehydrocondensation reaction of α,ω‐bis(trimethylsiloxy)methylhydridesiloxane and of α,ω‐bis(trimethylsiloxy)methylhydridesiloxane‐dimethylsiloxane with α‐hydroxy‐ω‐trimethylsiloxydiorganosilylenes, in the presence of anhydrous caustic potassium, at 1:35 and 1:33 ratio of initial compounds has been investigated and polyorganosiloxanes with rigid polydiorganosilylenes fragment in the side chain, completely soluble in organic solvents, have been obtained. The catalytic dehydrocondensation reaction order, activation energies, and rate constants have been determined. The synthesized copolymers were characterized by thermogravimetric, gel permeation chromatographic, differential scanning calorimetric, and wide‐angle X‐ray analyses. It was shown that during modification of α,ω‐bis(trimethylsiloxy)methylhydridesiloxane‐dimethylsiloxane with α‐hydroxy‐ω‐trimethylsiloxydiorganosilylenes in synthesized block‐copolymers, microdomain structure (phase incompatibility) was observed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2161–2167, 2007     

Synthesis and investigation of properties of silaoxadihydrophenanthrene‐diphenylsiloxane fragments containing block copolymers

The reaction of heterofunctional condensation of 1,1‐dichloro‐1‐sila‐2‐oxadihydrophenanthrene with dihydroxydiphenylsilane at various ratios of initial compounds in the presence of pyridine is investigated. α,ω‐Dihydroxysilaoxadihydrophenanthrene‐diphenylsiloxane oligomers with various degrees of condensation are obtained. Organosiloxane block copolymers with the regular arrangement of silaoxadihydrophenanthrene‐diphenylsiloxanes fragments in the main linear dimethylsiloxane chain are produced by the reaction of heterofunctional condensation of α,ω‐dihydroxysilaoxadihydrophenanthrene‐diphenylsiloxanes with α,ω‐dichlorodimethylsiloxanes in the presence of anhydrous pyridine, as an acceptor of hydrochloric acid. Thermogravimetry, differential scanning calorimetry, gel permeation chromatography, and wide‐angle X‐ray analysis are carried out on the synthesized block copolymers. The microheterogeneous structure of block copolymers is observed at definite values of the length of the flexible dimethylsiloxane chain by DSC and X‐ray investigation. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 9–16, 2002; DOI 10.1002/app.10045     

Poly(α-methylstyrene)–poly(dimethylsiloxane) block copolymers

Block copolymers were synthesized by the condensation of dihydroxyl-terminated poly-(α-methylstyrene) oligomers and bisdimethylamino-terminated poly(dimethylsiloxane) oligomers. Manipulation of block molecular weight produced copolymers ranging in composition from 21% to 73% poly(dimethylsiloxane). Compression moldablity was found to be good. Physical properties were dependent upon siloxane content, varying from high modulus, low elongation to low modulus, high elongation materials. High siloxane-content compositions exhibited elastomeric properties due to the two-phase morphology of these systems. Glass transition temperatures were observed as low as ?120°C for the poly(dimethylsiloxane) block and as high as + 140°C for the poly(α-methylstyrene) block. Even higher poly(α-methylstyrene) transition temperatures may be possible by using higher molecular weight oligomers.     

Block copolymers of styrene containing oligomeric esters of terephthalic acids

A new generation of block copolymers were synthesized starting with depolymerized PET by glycolysis with some oligomeric diols. α,ω‐Dihydroxy poly(dimethyl siloxane)s, hexylene glycol, poly(ethylene oxide)glycols, and ethylene glycol were used as diols. The dihydroxy‐terminated depolymerization products containing a terephthalyl group and oligomeric diols were used to prepare a diradicalic macroinitiator (MI). These MIs were used to polymerize the styrene monomer. The new block copolymers obtained were characterized by physical and chemical methods and mechanical and thermal analyses. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 648–653, 2000     

Block copolymers of acrylonitrile and poly(dimethylsiloxane)s

The chemical redox system of ceric ammonium nitrate(Ce⁴⁺) and poly(dimethylsiloxane)s (PDMS) with monohydroxy (MH), dihydroxy (DH), and diamine(DA) chain ends was used to polymerize acrylonitrile (AN) to produce monohydroxy poly(dimethylsiloxane)s‐b‐polyacrylonitrile (MH.PDMS‐b‐PAN), dihydroxy poly(dimethylsiloxane)s‐b‐polyacrylonitrile (DH.PDMS‐b‐PAN), and α, ω‐diamine poly(dimethylsiloxane)s‐b‐polyacrylonitrile (DA.PDMS‐b‐PAN) block copolymers. The concentration, reaction time, and the type of poly(dimethylsiloxane) affect the yield and the molecular weight of the copolymers. The ratio of AN/ceric salt/PDMS has remarkably affects the properties of formed copolymers. DH.PDMS‐b‐PAN copolymers were also prepared by electroinduced polymerization in the presence of catalytic amount of Ce⁴⁺ in a divided electrochemical cell where Ce³⁺ is readily oxidized into Ce⁴⁺ at the anode. The products were characterized by Fourier transform infrared spectroscopy, ¹H‐NMR spectroscopy, DSC, and their surface properties were investigated through contact‐angle measurements. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and characterization of PBMA‐b‐PDMS‐b‐PBMA copolymers by atom transfer radical polymerization

Poly(butyl methylacrylate)–b–poly(dimethylsiloxane)–b–poly(butyl methylacrylate) (PBMA–b–PDMS–b–PBMA) triblock copolymers were synthesized by atom transfer radical polymerization (ATRP). The reaction of α,ω‐dichloride PDMS with 2′‐hydroxyethyl‐2‐bromo‐2‐methylpropanoate gave suitable macroinitiators for the ATRP of BMA. The latter procedure was carried out at 110°C in a phenyl ether solution with CuCl and 4,4′‐di (5‐nonyl)‐2,2′‐bipyridine (dNbpy) as the catalyzing system. The polymerization was controllable, with the increase of the monomer conversion, there was a nearly linear increase of molecular weight and a decrease of polydispersity in the process of the polymerization, and the rate of the polymerization was first‐order with respect to monomer conversion. The block copolymers were characterized with IR and ¹H‐NMR and differential scanning calorimetry. The effects of macroinitiator concentration, catalyst concentration, and temperature on the polymerization were also investigated. Thermodynamic data and activation parameters for the ATRP were reported. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 532–538, 2004     

A new macroinitiator for the synthesis of triblock copolymers PA12‐b‐PDMS‐b‐PA12

A new PDMS macroinitiator is proposed for the anionic ring‐opening polymerization of lactams. This α,ω‐dicarbamoyloxy caprolactam PDMS macroinitiator was readily obtained in quantitative yield, by an original synthesis scheme in two steps, which involved the scarcely reported reaction of isocyanates with silanol groups. It was then shown that this bifunctional macroinitiator enabled to synthesize triblock copolymers PA12‐b‐PDMS‐b‐PA12 by polymerization of lauryl lactam (LL) at high temperature (200°C) in inert atmosphere under conditions compatible with reactive extrusion processes. Another related high molar weight α,ω‐diacyllactam PDMS macroinitiator was also successfully used in the polymerization of LL under the same conditions, therefore overcoming the limitations formerly reported for this type of macroinitiators during the polymerization ε‐caprolactam (ε‐CL) at a much lower temperature (80°C). Triblock copolymers with a wide range of PA12 /molar weights (M_n: ～ 10,800–250,000 Da) were eventually obtained by using both types of macroinitiators. DMTA and DSC analyses showed that their thermal properties were strongly dependent upon their respective contents in soft and hard blocks. Such triblock copolymers already appear very promising for the highly effective in situ compatibilization of PA12/PDMS blends as shown by recent complementary results obtained in our laboratory. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 102: 2818–2831, 2006     

Synthesis and characterization of poly(ϵ‐caprolactone)–poly(L‐lactide) diblock copolymers with an organic amino calcium catalyst

The quasiliving characteristics of the ring‐opening polymerization of ?‐caprolactone (CL) catalyzed by an organic amino calcium were demonstrated. Taking advantage of this feature, we synthesized a series of poly(?‐caprolactone) (PCL)–poly(L ‐lactide) (PLA) diblock copolymers with the sequential addition of the monomers CL and L ‐lactide. The block structure was confirmed by ¹H‐NMR, ¹³C‐NMR, and gel permeation chromatography analysis. The crystalline structure of the copolymers was investigated by differential scanning calorimetry and wide‐angle X‐ray diffraction analysis. When the molecular weight of the PLA block was high enough, phase separation took place in the block copolymer to form PCL and PLA domains, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2654–2660, 2006     

Polyimide–polysiloxane block copolymers synthesized from α, ω-(3-aminophenoxy) terminated poly[oxy(dimethylsilyl)-1,4-phenylene(dimethylsilylene)]s

A method has been worked out for the synthesis of α,ω-(3-aminophenoxy) terminated poly[oxy(dimethylsilyl)-1,4-phenylene(dimethylsilylene)]oligomers with controlled molecular weight. From these oligomers were synthesized polyimide-polysiloxane block copolymers via a transimidization route, with polyimide moieties based on 2-aminopyridine terminated 5,5′-oxybis-1,3-isobenzofuranedione-4,4′-[1,4-phenylenebis(1-methylethylidene)]bisaniline oligomers. The copolymers obtained show higher thermooxidative stability in comparison with copolymers having siloxane moiety based on α,ω-aminopropyl or α,ω-arylamine terminated poly(dimethylsiloxane) oligomers.