Dilute solution properties of carboxymethylchitins in high ionic-strength solvent

The hydrodynamic characteristics in aqueous solution at ionic strength I=0.2  of carboxymethylchitins of different degrees of chemical substitution have been determined. Experimental values varied over the following ranges: the translational diffusion coefficient (at 25.0°C), 1.1<10⁷×D<2.9 cm² s⁻¹; the sedimentation coefficient, 2.4<s<5.0 S; the Gralen coefficient (sedimentation concentration-dependence parameter), 130<k_s<680 mL g⁻¹; the intrinsic viscosity, 130<[η]<550 mL g⁻¹. Combination of s with D using the Svedberg equation yielded ‘sedimentation–diffusion' molecular weights in the range 40 000<M<240 000 g mol⁻¹. The corresponding Mark–Houwink–Kuhn–Sakurada (MHKS) relationships between the molecular weight and s, D and [η] were: [η]=5.58×10⁻³ M^0.94; D=1.87×10⁻⁴ M^−0.60; s=4.10×10⁻¹⁵ M^0.39. The equilibrium rigidity and hydrodynamic diameter of the carboxymethylchitin polymer chain is also investigated on the basis of wormlike coil theory without excluded volume effects. The significance of the Gralen k_s values for these substances is discussed.     

Thermoelectric characterization of NaxMx/2Ti1−x/2O2 (M=Co, Ni and Fe) polycrystalline materials

Layered -titanate materials, Na_xM_x/2Ti_1−x/2O₂ (M=Co, Ni and Fe, x=0.2–0.4), were synthesized by flux reactions, and electrical properties of polycrystalline products were measured at 300–800 °C. After sintering at 1250 °C in Ar, all products show n-type thermoelectric behavior. The values of both d.c. conductivity and Seebeck coefficient of polycrystalline Na_0.4Ni_0.2Ti_0.8O₂ were ca. 7×10³ S/m and ca. −193 μV/K around 700 °C, respectively. The measured thermal conductivity of layered -titanate materials has lower value than conductive oxide materials. It was ca. 1.5 Wm⁻¹ K⁻¹ at 800 °C. The estimated thermoelectric figure-of-merit, Z, of Na_0.4Ni_0.2Ti_0.8O₂ and Na_0.4Co_0.2Ti_0.8O₂ was about 1.9×10⁻⁴ and 1.2×10⁻⁴ K⁻¹ around 700 °C, respectively.     

Nanosized perovskite-type oxides La1−xSrxMO3−δ (M = Co, Mn; x = 0, 0.4) for the catalytic removal of ethylacetate

Nanometer perovskite-type oxides La_1−xSr_xMO_3−δ (M = Co, Mn; x = 0, 0.4) have been prepared using the citric acid complexing-hydrothermal-coupled method and characterized by means of techniques, such as X-ray diffraction (XRD), BET, high-resolution scanning electron microscopy (HRSEM), X-ray photoelectron spectroscopy (XPS), temperature-programmed desorption (TPD), and temperature-programmed reduction (TPR). The catalytic performance of these nanoperovskites in the combustion of ethylacetate (EA) has also been evaluated. The XRD results indicate that all the samples possessed single-phase rhombohedral crystal structures. The surface areas of these nanomaterials ranged from 20 to 33 m² g⁻¹, the achievement of such high surface areas are due to the uniform morphology with the typical particle size of 40–80 nm (as can be clearly seen in their HRSEM images) that were derived with the citric acid complexing-hydrothermally coupled strategy. The XPS results demonstrate the presence of Mn⁴⁺ and Mn³⁺ in La_1−xSr_xMnO_3−δ and Co³⁺ and Co²⁺ in La_1−xSr_xCoO_3−δ, Sr substitution induced the rises in Mn⁴⁺ and Co³⁺ concentrations; adsorbed oxygen species (O⁻, O₂⁻, or O₂²⁻) were detected on the catalyst surfaces. The O₂-TPD profiles indicate that Sr doping increased desorption of the adsorbed oxygen and lattice oxygen species at low temperatures. The H₂-TPR results reveal that the nanoperovskite catalysts could be reduced at much lower temperatures (<240 °C) after Sr doping. It is observed that under the conditions of EA concentration = 1000 ppm, EA/oxygen molar ratio = 1/400, and space velocity = 20,000 h⁻¹, the catalytic activity (as reflected by the temperature (T_100%) for EA complete conversion) increased in the order of LaCoO_2.91 (T_100% = 230 °C) ≈ LaMnO_3.12 (T_100% = 235 °C) < La_0.6Sr_0.4MnO_3.02 (T_100% = 190 °C) < La_0.6Sr_0.4CoO_2.78 (T_100% = 175 °C); furthermore, there were no formation of partially oxidized by-products over these catalysts. Based on the above results, we conclude that the excellent catalytic performance is associated with the high surface areas, good redox properties (derived from higher Mn⁴⁺/Mn³⁺ and Co³⁺/Co²⁺ ratios), and rich lattice defects of the nanostructured La_1−xSr_xMO_3−δ materials.     

Effects of physical ageing on creep in polypropylene

Creep data have been obtained for polypropylene at 23°C over an extensive time range (10⁻⁸–10⁶ s) as a function of the elapsed time t_e between quenching from 80°C and the start of the creep experiment. The creep curves have been fitted with empirical functions capable of describing the behaviour across the entire β- and -relaxation regions. Analyses of results from both short-term (t0.1 t_e) and long-term tests suggest that physical ageing produces a decrease in relaxed compliance for the β-(glass-rubber) relaxation together with an increase in average retardation time and broadening of the -process. Some decrease in magnitude of the -relaxation also seems to be significant. It is proposed that ageing in polypropylene at room temperature could involve decreases in contour length of amorphous tie-molecules (yielding more extended conformations) through coupled motions in the crystalline and amorphous regions associated with the -mechanism.     

Mercury-mercurous propionate electrode: standard potentials at different temperatures and related thermodynamic quantities

The standard molal potentials E°_m of the Hg/Hg₂(OPr)₂, OPr⁻ electrode at 15°, 20°, 25°, 30° and 35° C have been determined. The E°_m values obtained are 0.5114, 0.5072, 0.5031, 0.4988 and 0.4942 V respectively, which can be fitted to the equation Edg_m/V = 0.5031 −8.56 × 10⁻⁴ (itt/°C − 25)−3.0588 × 10⁻⁶ (t/ °C -25)². The changes in standard free energy, entropy and enthalpy for the cell reaction have been calculated.     

Phase transition phenomena of the adsorbed 1-dodecanol monolayer at the air–water interface

Phase transition phenomenon of the 1-dodecanol monolayer at the air/water interface was studied by the dynamic γ(t) curves and the adsorption isotherm obtained by ellipsometry at 20 °C. The surface-concentration adsorption isotherm clearly showed three abrupt increases at bulk concentration C of 1.3 × 10⁻⁹, 2 × 10⁻⁹ and 3.7 × 10⁻⁹ mol/mL, respectively. The 1st and the 3rd transitions observed herein, that were typical 2D first-order transitions, were consistent with the gas to liquid expanded (G–LE) and the liquid expanded to liquid condensed (LE–LC) phase transitions observed in a previous tensiometry study. The 2nd transition that occurred at C = 2 × 10⁻⁹ mol/mL was not identified from any previous dynamic surface-tension profiles. Judging from the substantial increase in the film thickness of the transition, it was believed that the orientation change of the adsorbed molecule was involved in the LE phase. A LE_h and a LE_v phase, that denoted the “lie-down” and “stand-up” types of adsorption, respectively, was used to describe this transition and a cusp, instead of a constant surface-tension region, was observed in the dynamic γ(t) curves for this transition. This suggested that, since the surface tension varied during the transition process, the newly identified LE_h and LE_v transition might not be the typical first-order type of phase transition.     

Surface dynamics during latex film formation

Surface dynamics during latex film formation has been investigated theoretically and experimentally by atomic force microscopy. The peak-to-valley distance, y(t), of the latex particles in the surface plane of the latex film decayed exponentially with time during film formation. A theoretical relationship between y(t) and time, t, is given by y(t)=y(0) exp[−t/τ], where y(0) is the value of y(t) when t is zero. τ is a characteristic constant related to the nature of polymer, the particle radius, the surface diffusion coefficient and the temperature. The relationship between the surface diffusion coefficient, D_s, y(0), the radius of the latex particles, R, temperature, T, and τ is given approximately by D_s=1.2×10⁻²⁰y(0)²[2R−y(0)]²T/τ (cm²/s), where the units are manometers for y(0) and R, kelvin for temperature, and seconds for τ. By measuring the decay of y(t) with time, the surface diffusion coefficient can be obtained. The surface diffusion coefficient for a poly(methyl methacrylate-co-butylacrylate) (50:50) copolymer latex film was found to be A×10⁻¹³ cm²/s, A is temperature-dependent.     

Adsorption of methane/ethane mixtures on dry coal at elevated pressure

The binary adsorption characteristics of methane and ethane on dry coal to 40 atm pressure have been calculated from pure-component isotherms. In some coal seams, pressures exceeding 40 atm have been recorded and the methane sampled from the virgin coal often shows a few percent of ethane. The binary adsorption characteristics were calculated by employing the ideal adsorbed solution theory of Myers and Prausnitz, and experimentally-determined (Type I) pure gas isotherms at 0, 30 and 50 °C. The coal used in this investigation was high-volatile ‘A’ bituminous (hvab) from the Pennsylvania Pittsburgh seam. Gas nonideality was accounted for by replacing pressure with fugacity. Adsorption of methane on dry coal is purely physical; the isosteric heat of adsorption does not exceed 2.4 kcal/mol^* at 30 °C on the above coal. Isobars on the resulting binary equilibrium diagram exhibited an unexpected phenomenon of intersecting each other which might be attributable to the above nonideality considerations. The region of a few percent of ethane, which is of practical importance from the viewpoint of coal seams, was expanded and reduced to an equation: V(CH₄) = −21.52 + 7.18(VF) + 16.88(VF)² −0.395(P) − 0.00661(P)² + 0.824(T) − 0.00030(T)² + 0.928(VF)(P) − 0.858(VF)(T). V(Total) = 25.9 − 23.6(VF) + 0.655(P) − 0.00875(P)² − 0.795(T) + 0.743(VF)(T) where V(CH₄) and V(Total) = cm³(STP)CH₄ and total gas respectively adsorbed per g dry coal; VF = vol. fraction of methane as analysed at 1 atm (0.94 VF 1.0); P = seam pressure, atm (0 P 40); T=seam temperature, °C(−10 T 50).     

Comparative study of lithium ion conductors in the system Li1+xAlxA2−x (PO4)3 with A=Ti or Ge and 0≤x≤0·7 for use as Li sensitive membranes

Preparations and physico-chemical characterizations of NASICON-type compounds in the system Li_1+xAl_xA_2−x^IV(PO₄)₃ (A^IV=Ti or Ge) are described. Ceramics have been fabricated by sol-gel and co-grinding processes for use as ionosensitive membrane for Li⁺ selective electrodes. The structural and electrical characteristics of the pellets have been examined. Solid solutions are obtained with Al/Ti and Al/Ge substitutions in the range 0≤x≤0·6. A minimum of the rhombohedral c parameter appears for x about 0·1 for both solutions. The grain ionic conductivity has been characterized only in the case of Ge-based compounds. It is related to the carrier concentration and the structural properties of the NASICON covalent skeleton. The results confirm that the Ti-based framework is more calibrated to Li⁺ migration than the Ge-based one. A grain conductivity of 10⁻³ S cm⁻¹ is obtained at 25°C in the case of Li_1·3Al_0·3Ti_1·7(PO₄)₃. A total conductivity of about 6×10⁻⁵ S cm⁻¹ is measured on sintered pellets because of grain boundary effects. The use of such ceramics in ISE devices has shown that the most confined unit cell (i.e. in Ge-based materials) is more appropriate for selectivity effect, although it is less conductive.©     

Synthesis, densification and electrical properties of strontium cerate ceramics

Powders of pure and 5% ytterbium substituted strontium cerate (SrCeO₃/SrCe_0.95Yb_0.05O_3−δ) were prepared by spray pyrolysis of nitrate salt solutions. The powders were single phase after calcination in nitrogen atmosphere at 1100 °C (SrCeO₃) and 1200 °C (SrCe_0.95Yb_0.05O_3−δ). Dense SrCeO₃ and SrCe_0.95Yb_0.05O_3−δ materials were obtained by sintering at 1350–1400 °C in air. Heat treatment at 850 and 1000 °C, respectively, was necessary prior to sintering to obtain high density. The dense materials had homogenous microstructures with grain size in the range 6–10 μm for SrCeO₃ and 1–2 μm for SrCe_0.95Yb_0.05O_3−δ. The electrical conductivity of SrCe_0.95Yb_0.05O_3−δ was in good agreement with reported data, showing mixed ionic–electronic conduction. The ionic contribution was dominated by protons below 1000 °C and the proton conductivity reached a maximum of 0.005 S/cm above 900 °C. In oxidizing atmosphere the p-type electronic conduction was dominating above 700 °C, while the contribution from n-type electronic conduction only was significant above 1000 °C in reducing atmosphere.     

Wettability of nanocrystalline diamond films

The wettability of nanocrystalline CVD diamond films grown in a microwave plasma using Ar/CH₄/H₂ mixtures with tin melt (250–850 °C) and water was studied by the sessile-drop method. The films showed the highest contact angles θ of 168 ± 3° for tin among all carbon materials. The surface hydrogenation and oxidation allow tailoring of the θ value for water from 106 ± 3° (comparable to polymers) to 5° in a much wider range compared to microcrystalline diamond films. Doping with nitrogen by adding N₂ in plasma strongly affects the wetting presumably due to an increase of sp²-carbon fraction in the films and formation of C–N radicals.     

Electrical conductance of KI in anhydrous acetonitrile

The electrical conductivity of KI solutions in anhydrous acetonitrile has been determined at 0, 25 and 35°C in the concentration range 0·9– 600 × 10⁻⁴ mole/l. The values of Λ₀, K and a calculated from the results are, respectively: 145·9 mho/cm, 0·95 × 10 ⁻² and 1·72 Å at 0°C; 186·2 mho/cm, 8·98 × 10⁻² and 4·6 Å at 25°C; and 204·8 mho/cm, 5·17 × 10⁻² and 3·5 Å at 35°C. The phoreograms at all the three temperatures are catabatic at lower concentration, but become anabatic at 0·017, 0·022 and 0·024 respectively, at 0, 25 and 35°C.     

Electrocatalytic oxidation of p-nitrophenol from aqueous solutions at Pb/PbO2 anodes

In this work, the elimination of p-nitrophenol (p-NPh) from aqueous solutions by electrochemical oxidation at Pb/PbO₂ anodes was investigated. The process was studied under galvanostatic polarization mode in acidic and alkaline media, as a function of the temperature (20, 40 and 60 °C) and of the anodic current density (J = 10, 20 and 30 mA cm⁻²). In acidic media (0.5 M H₂SO₄), the oxidation process allowed a 94% p-NPh conversion in 7 h, at 20 °C and with J = 20 mA cm⁻², with a wide distribution of degradation products (in particular: 39% p-benzoquinone and 26% hydroquinone, as given by a mass balance at the above electrolysis time). Under these conditions, the current efficiency for the substrate oxidation was 15.4% ([Ah L⁻¹]_exp = 7 versus [Ah L⁻¹]_theo = 1.08 Ah L⁻¹). In alkaline media (0.1 M NaOH, pH 8.5), the most effective p-NPh elimination (97%) was obtained at 60 °C, 20 mA cm⁻² and 420 min of electrolysis time, again with the production of p-benzoquinone and hydroquinone (52.7 and 15.1%, respectively). Under the latter conditions, an almost complete chemical oxygen demand (COD) abatement was attained, with a high level of p-NPh mineralization (>80%), a yield of p-NPh conversion greater than 95% and a scarce formation of aliphatic acids (most probably maleic acid). From the degradation curves ([p-NPh] versus t), in both acidic and alkaline media, the UV analyses and/or COD measurements, a complete oxidation of aliphatic acids to form CO₂ could be predicted for electrolysis time >420 min, according to a suggested oxidation pathway.     

H4SiW12O40-catalyzed oxidation of nitrobenzene in supercritical water: kinetic and mechanistic aspects

The catalytic effect of a heteropolyacid, H₄SiW₁₂O_40, on nitrobenzene (20 and 30 μM) oxidation in supercritical water was investigated. A capillary flow-through reactor was operated at varying temperatures (T=400–500 °C; P=30.7 MPa) and H₄SiW₁₂O₄₀ concentrations (3.5–34.8 μM) in an attempt to establish global power-law rate expressions for homogenous H₄SiW₁₂O₄₀-catalyzed and uncatalyzed supercritical water oxidation. Oxidation pathways and reaction mechanisms were further examined via primary oxidation product identification and the addition of various hydroxyl radical scavengers (2-propanol, acetone, acetone-d₆, bromide and iodide) to the reaction medium. Under our experimental conditions, nitrobenzene degradation rates were significantly enhanced in the presence of H₄SiW₁₂O₄₀. The major differences in temperature dependence observed between catalyzed and uncatalyzed nitrobenzene oxidation kinetics strongly suggest that the reaction path of H₄SiW₁₂O₄₀-catalyzed supercritical water oxidation (average activation E_a=218 kJ/mol; k=0.015–0.806 s⁻¹ energy for T=440–500 °C; E_a=134 kJ/mol for the temperature range T=470–490 °C) apparently differs from that of uncatalyzed supercritical water oxidation (E_a=212 kJ/mol; k=0.37–6.6 μM s⁻¹). Similar primary oxidation products (i.e. phenol and 2-, 3-, and 4-nitrophenol) were identified for both treatment systems. H₄SiW₁₂O₄₀-catalyzed homogenous nitrobenzene oxidation kinetics was not sensitive to the presence of OH√ scavengers.     

Micromechanics of domain switching in rhombohedral PZT ceramics

The lattice strain {2 0 0} and diffraction peak intensity ratio R{1 1 1} have been determined in soft rhombohedral PZT ceramics during the application of an electric field up to 2.5 MV m⁻¹ and as a function of the grain orientation ψ, using high energy synchtron X-ray diffraction. The magnitude of both {2 0 0} and R{1 1 1} increased sharply beyond a field level of 1 MV m⁻¹ due to the onset of ferroelectric domain switching. {2 0 0} exhibited a near linear dependence on cos² ψ, in agreement with previous studies of the remanent-poled state. In contrast, the R{1 1 1}–cos² ψ plot showed evidence of saturation in ferroelectric domain switching, particularly for ψ > 60°. The development of lattice strain during poling is discussed in terms of contributions from the intrinsic piezoelectric effect and from residual stress caused by differences in the poling strain of a grain, and the piezoelectric strain of a grain relative to its surroundings.     

Viscoelastic properties of cellulose derivatives: 1. Cellulose acetate

The dynamic mechanical spectrum of cellulose acetate (CA) from −130°C to 240°C has been determined at different frequencies (from 0.1 to 30 Hz). Three relaxations, designated , β and γ in order of decreasing temperature, and one shoulder (β*) above room temperature were found. Comparison with calorimetric and thermogravimetric measurements yields the conclusion that the relaxation (197°C at 3 Hz) is related to the glass-to-rubber transition and the β* shoulder (50°C–100°C) is due to loss of moisture. The β relaxation (−38°C at 3 Hz, ΔH = 100 kJ mol⁻¹) is tentatively assigned to local motions of the main chain (glucopyranose rings). The low-temperature γ relaxation (−88°C at 3 Hz, ΔH = 46 kJ mol⁻¹), is humidity-dependent: its intensity decreases when the samples are dried to moisture contents lower than that obtained by normal room conditioning (about 3%). Higher water contents shift the relaxation to lower temperatures without increasing the intensity of the mechanical loss. It is suggested that water associated with the unesterified methylol groups of cellulose acetate is responsible of the dynamic mechanical γ dispersion.     

Aerosol measurement by laser doppler spectroscopy—II. Operational limits, effects of polydispersity, and applications

The theoretical basis and the results of a computer simulation are presented which describe the operational limits of size and concentration for aerosol sizing by laser Doppler spectroscopy LDS,. This analysis suggests that a state of the art LDS system has the capability of sizing 0·03 μm diameter particles when the number concentration is 10⁸ cm⁻³ or greater and 0·2 μm diameter for coocentrations as low as 100 particles cm⁻³. An evaluation of the effect on the laser Doppler spectroscopy measurements of a polydisperse aerosol having a log normal size distribution is presented and methods for combining these measurements with other averaged measurements to determine both count median diameter (CMD) and geometric standard deviation (δ_g) are proposed. For aerosols having log normal distributions with 0·3 < CMD < 3 μm and 1·0 < δ_g < 2·0, laser Doppler spectroscopy is able to measure the surface area median diameter within ± 15 per cent, independent of polydispersity. Applications of LDS to aerosol sizing are evaluated and its advantages and disadvantages relative to other sizing methods are discussed.     

Grain growth in TiO2-added ZnO–Bi2O3–CoO–MnO ceramics prepared by chemical processing

The effect of TiO₂ on the grain growth of the ZnO–Bi₂O₃–CoO–MnO ceramic system prepared by chemical coprecipitation, was studied between 1150 and 1300 °C in air. Bi₂O₃ melts during firing, and then TiO₂ dissolves into Bi₂O₃-rich liquid. TiO₂ initially reacts with Bi₂O₃ to form Bi₄Ti₃O₁₂. Above ≈1050 °C, Bi₄Ti₃O₁₂ reacts with ZnO to form Zn₂TiO₄ spinel phase. The kinetic study of grain growth carried out using the expression Gⁿ–G_oⁿ=K_o·t·exp(−Q/RT) gave grain exponent (n) value as 6 and the apparent activation energy (Q) as 226.46 kJ/mol. 1.00 mol% TiO₂ addition increased the grain growth exponent value from 6 to 7 and apparent activation energy with 1.00 mol% TiO₂ addition was found to be 197.10 kJ/mol. The ZnO grain size gradually increases with increasing TiO₂ content. Addition of TiO₂ may increase the reactivity of the Bi₂O₃-rich liquid towards the ZnO grain, thus affecting the ZnO grain growth.     

Catalytic oxidation of methane over hexaaluminates and hexaaluminate-supported Pd catalysts

An aqueous (NH₄)₂CO₃ coprecipitation method, based on that of Groppi et al. [Appl. Catal. A 104 (1993) 101–108] was used to synthesize Sr_1−xLa_xMnAl₁₁O₁₉₋ hexaaluminates. These materials were first synthesized by alkoxide hydrolysis. This synthesis route requires special handling of the starting materials and is not likely to be commercially practical. The materials prepared by (NH₄)₂CO₃ coprecipitation have similar surface areas as those prepared by the alkoxide hydrolysis method. Their CH₄ oxidation activity, measured as the temperature needed for 10% conversion of methane, is higher than those prepared by alkoxide hydrolysis. The La-substantiated material, LaMnAl₁₁O₁₉₋, shows high surface area with 19.3 m²/g after calcination at 1400°C for 2 h. It is active for CH₄ oxidation with T_10% at 450°C using 1% CH₄ in air and 70 000 cm³/h g space velocity. The stability and activity of LaMnAl₁₁O₁₉₋ prepared by (NH₄)₂CO₃ coprecipitation method is a simple and important step forward for the application of CH₄ catalytic combustion for gas turbines.     

Influence of exchanged cations (Na, Cs, Sr and Ba) on xylene permeation through ZSM-5/SS tubular membranes

Na-ZSM-5 membranes were synthesized by secondary growth on the outer surface of stainless steel porous tubes. The membranes were ion-exchanged with Cs⁺, Ba²⁺ and Sr²⁺ to investigate their effect upon the separation of p-xylene from m-xylene and o-xylene. The permeation through the membranes was measured between 150 and 400 °C using each xylene isomer separately and a ternary mixture. All the membranes were selective to p-xylene in the temperature range studied. N₂ and xylene permeation measurements together with SEM observations were used to determine whether or not cracks and/or pinholes developed after exposure to the xylene isomers at high temperature (400 °C). Neither pore blockage nor extra-zeolitic pores developed after the ion exchange procedure and subsequent calcination. Furthermore, duplicate synthesized membranes of each cation form had similar separation factors and permeances. The duplicate values differ much less than the measurement error. The p-xylene permeation flux decreased in the order: Na-ZSM-5 > Ba-ZSM-5 > Sr-ZSM-5  Cs-ZSM-5 while the permeation flux of the m- and o-xylene decreased in the order Na-ZSM-5 > Sr-ZSM-5 > Ba-ZSM-5 > Cs-ZSM-5. The membrane that exhibited the best performance was Ba-ZSM-5, with a maximum p/o separation factor of 8.4 and a p-xylene permeance of 0.54 × 10⁻⁷ mol s⁻¹ m⁻² Pa⁻¹ at 400 °C.