磁性介孔碳的制备及对水体中染料的吸附去除

以介孔氧化硅SBA-15为硬模板,采用三氯化铁与蔗糖同步浇筑法制备磁性介孔碳材料.扫描电镜、透射电镜、比表面积和振动磁强计等分析表明,该材料具有有序的介孔孔道和较好的磁分离性能.考察其对亚甲基蓝(MB)和日落黄(SY)的吸附性能,结果发现溶液的pH对吸附两种染料有显著的影响,阳离子染料亚甲基蓝随着溶液pH的增大吸附量显著升高,而阴离子染料日落黄则相反.由Langmuir吸附等温模型拟合出亚甲基蓝、日落黄的最大吸附容量分别为473.9 mg·g~(-1)和434.8 mg·g~(-1).该磁性介孔材料在染料污染物的去除方面具有较好的应用潜力.     

甘氨酸改性TiO_2材料的合成及其对染料的吸附性能

本文以钛酸异丙酯为钛源,以甘氨酸(gly)为改性材料,通过水解法在比较温和的条件下合成了二氧化钛(TiO_2-gly)吸附剂,同时以亚甲基蓝(MB)和酸性红G (ARG)两种染料为处理对象,考察了合成的TiO_2的吸附性能,并将之与P25材料进行对比.结果表明,经过甘氨酸改性的TiO_2吸附剂的比表面积大幅提升到354.2 m2·g~(-1);改性TiO_2对亚甲基蓝(100 mg·L-1)和酸性红G (100 mg·L-1)两种染料的吸附能力得到较大提高,最大吸附量分别为49.25 mg·g~(-1)和43.98 mg·g~(-1),远高于P25对二者的吸附容量(分别为28.24 mg·g~(-1)和16.40 mg·g~(-1)); P25的吸附主要受物理吸附作用控制,而改性TiO_2吸附剂20 min即可达到吸附平衡,并展现出准二级动力学和Langmuir吸附等温线特性,这表明吸附剂与染料分子之间主要为化学吸附.另外,通过吸附影响因素实验发现通过延长吸附时间、控制p H都能提高该吸附剂的吸附性能,而改性TiO_2-gly吸附剂经过5次再生循环实验后仍展现出较好的吸附性能.     

纳米TiO_2多孔微粒阳光催化降解活性艳蓝染料

首次利用高分子悬浮聚合与溶胶-凝胶法相结合的技术,成功地制备不同孔结构的TiO2多孔微粒,并对其光催化降解活性艳蓝KN-R的染料溶液pH、无机阴离子、光强、通空气等影响因素进行了系统研究。结果表明:强酸性条件有利于染料在催化剂表面的吸附,而强碱性条件有利于催化反应的进行;常见无机阴离子Cl-、SO42-,对染料降解有不同程度的抑制作用;染料降解效率随光强增加而提高;光降解动力学结果表明:TiO2多孔微粒对活性艳蓝KN-R染料的光催化降解反应符合一级反应动力学;降解时持续通空气有利于降解效率的提高。实验证明所制得的微粒具有良好的光催化降解效果和重复使用性能。     

染料化合物在改性介孔TiO_2上的吸附

以聚乙烯醇-碘复合物修饰的介孔TiO2纳米材料为吸附剂,研究了介孔TiO2对亚甲基蓝、甲基橙、茜素红和二甲酚橙染料化合物的吸附作用.考察了4种染料初始浓度和初始pH值对吸附的影响.实验结果表明,染料化合物的结构和性质影响介孔TiO2对它们的吸附平衡时间和吸附量.二甲酚橙、甲基橙、茜素红和亚甲基蓝有最佳吸附去除率的初始pH值分别为2.0、2.0、3.0和8.0;平衡吸附时间分别为100 min、10 min、100 min和60 min.介孔TiO2对亚甲基蓝、茜素红、二甲酚橙的饱和吸附量分别为80.32 mg·g-1、78.72 mg·g-1、71.64 mg·g-1,甲基橙的饱和吸附量超过200 mg·g-1.改性介孔TiO2对亚甲基蓝、茜素红、二甲酚橙的吸附符合二级动力学方程.     

纳米Ti02多孔微粒阳光催化降解活性艳蓝染料

首次利用高分子悬浮聚合与溶胶—凝胶法相结合的技术，成功地制备不同孔结构的TiO2多孔微粒，并对其光催化降解活性艳蓝KN—R的染料溶液PH、无机阴离子、光强、通空气等影响因素进行了系统研究。结果表明：强酸性条件有利于染料在催化剂表面的吸附，而强碱性条件有利于催化反应的进行；常见无机阴离子cl^-、so4^2-，对染料降解有不同程度的抑制作用；染料降解效率随光强增加而提高；光降解动力学结果表明：TiO2多孔微粒对活性艳蓝KN—R染料的光催化降解反应符合一级反应动力学；降解时持续通空气有利于降解效率的提高。实验证明所制得的微粒具有良好的光催化降解效果和重复使用性能。     

芬顿试剂法制备磁性碳纳米管及其对亚甲基蓝的吸附性能

采用芬顿试剂法在碳纳米管纯化样品表面负载纳米磁性氧化铁颗粒,制备磁性碳纳米管杂化材料(MWCNTs/Fe2O3),该杂化材料具有较高的纳米氧化铁负载率(>50%)和优异的磁性能,制备过程中无需额外添加阳离子,不会对环境造成不利影响.将磁性碳纳米管杂化材料应用于染料废水处理中,结果发现MWCNTs/Fe2O3对亚甲基蓝染料吸附性能较好,吸附后用磁铁易于达到固液分离的效果.吸附性能研究表明,磁性碳纳米管对水溶液中亚甲基蓝的吸附在40 min内吸附容量迅速上升,其值达到最大平衡吸附容量的88%以上,60 min基本达到平衡,吸附过程符合准二级动力学模型(R2>0.999).磁性碳纳米管吸附亚甲基蓝的平衡吸附量qe与亚甲基蓝溶液的平衡浓度Ce的关系满足Langmuir(R2>0.999)、Freundlich(R2>0.97)以及Dubinin-Radushkevich(D-R)(R2>0.96)等温吸附模型.通过Langmuir模型计算可知磁性碳纳米管对亚甲基蓝的最大吸附容量为69.98 mg.g-1,吸附过程为有利吸附,由D-R模型计算结果可以推断MWCNTs/Fe2O3对水溶液中亚甲基蓝的吸附机制以化学吸附为主.     

改性碳纳米管原始样品吸附亚甲基蓝的性能研究

利用直接制备的碳纳米管原始样品作为染料亚甲基蓝的吸附剂,采用次氯酸钠溶液对于碳纳米管原始样品进行表面修饰改性,改性处理后碳纳米管对亚甲基蓝吸附性较好,本工艺简单有效,所获得的吸附剂具有磁性,吸附过后用磁铁易于达到固液分离的效果.吸附性能结果表明:本吸附剂对水溶液中亚甲基蓝的吸附在60 min基本达到平衡,吸附过程符合准二级动力学模型(R2>0.99).改性后的磁性碳纳米管吸附亚甲基蓝的平衡吸附量qe与亚甲基蓝溶液的平衡浓度Ce的关系满足Langmuir(R2>0.99)、Freundlich(R2>0.91)以及Dubinin-Radushkevich(D-R)(R2>0.92)等温吸附模型.通过Langmuir模型计算可知改性磁性碳纳米管对亚甲基蓝的最大吸附容量为101.6 mg.g-1,由D-R模型计算结果可以推断,次氯酸钠改性后的磁性碳纳米管对水溶液中亚甲基蓝的吸附机理以化学吸附为主.     

茶渣负载纳米四氧化三铁复合材料制备及其对亚甲基蓝的吸附机理

采用化学沉淀法将Fe_3O_4纳米颗粒负载到茶渣(tea waste,TW)上,之后对TW-Fe_3O_4复合材料进行表征,并研究其对典型染料废水亚甲基蓝(MB)的去除效果及机理.结果表明,固液比为4.0 g·L~(-1),p H(6.92)未调整,接触时间为120 min,TW-Fe_3O_4对亚甲基蓝去除率可达98.70%.拟二级动力学模型可较好描述TW-Fe_3O_4吸附亚甲基蓝的过程.TW-Fe_3O_4复合材料对亚甲基蓝的去除可分为快吸附和慢吸附两个阶段.Langmuir、Temkin和Dubinin-Radushkevich模型均能较好拟合吸附过程.Langmuir拟合得到的最大饱和吸附量为84.47 mg·g~(-1).3次吸附-解吸循环实验之后,发现TW-Fe_3O_4对MB去除效果有限,表明结合较为稳定.TW-Fe_3O_4对MB的吸附机理涉及静电作用、离子交换、氢键作用、π-π堆积等.动力学、FTIR和XPS分析显示茶渣的表面官能团在吸附中能发挥重要作用.因此,TW-Fe_3O_4复合材料有作为染料污染废水修复剂的潜力,且能较为方便的从溶液中分离.     

一株染料脱色酵母菌的鉴定及脱色特性

从土壤中分离到一株活性艳红K-2BP脱色酵母菌株Y-63,根据其生理生化特征和26S rRNA基因序列相似性分析,鉴定为Pseudozyma rugulosa.该菌在16 h内对100 mg/L的活性艳红K-2BP脱色率为94%,其机理属于降解脱色.该染料脱色的最佳接种量(φ)应不低于5%,最适pH在4～9之间,(NH4)2SO4浓度(w)不低于0.1%,葡萄糖浓度(w)不低于0.2%.此外,该菌株对其它9种50 mg/L的染料(活性艳蓝X-BR、媒介漂蓝B、活性翠蓝KN-G、酸性媒介黄GG、媒介红S-80、依加仑蓝FBL 200%、弱酸艳红B、活性黑KN-B和活性红M-3BE)的脱色率在10%～96%之间.该研究表明酵母Y-63在染料废水的处理上具有较好的应用潜能.     

纤维素基吸附剂——绿色、经济的水处理材料

介绍了一类基于天然纤维素的水处理用吸附剂.对纤维素修饰羧基等阴离子基团,可以用来吸附水中的重金属阳离子(如cd(2+)、Cu(2+)、Hg(2+)、Ni(2+)、Pb(2+).对纤维素修饰铝铁或胺基等成分,可以吸附水中含砷阴离子、氟离子等有害阴离子.在纤维素上修饰疏水链,可以吸附水中氯苯、染料等危害健康的有机物.     

Evaluation of adsorption potential of adsorbents: a case of uptake of cationic dyes

Adsorption potential of a commercial activated carbon (FS300) has been evaluated for the uptake of cationic dyes namely methylene blue (MB) and rhodamine B (RB). Though, there are numerous studies in literature which report the sorption of MB (more than 40 studies) and RB (more than 10), however none of these use a common parameter to report the capacity of the sorbent. A protocol, based on the equilibrium dye concentration has been proposed to measure the sorption potential of a sorbent. The Langmuir model can very well describe the experimental equilibrium data for both dyes (coefficient of correlation > 0.999). MB (Qm = 312.5 mg g(-1)) is more adsorbable than the RB (Qm = 144.9 mg g(-1)). Molecular weight and chemical structure of dye molecules seem to affect the dye uptake. The effect of pH on dye uptake has also been evaluated by varyingpH from 3 to 11. Uptake of MB increases with pH, wherein RB removal decreases with pH. Dyes could not be desorbed either by distilled water (0.06 and 0.11% for MB and RB respectively), or by 0.1 NHCl (0.136 and 3.0% for MB and RB respectively) indicating, chemical adsorption type of adsorbent-adsorbate interactions.     

Selective sorption of perfluorooctane sulfonate on molecularly imprinted polymer adsorbents

Perfluorooctane sulfonate (PFOS), as a potential persistent organic pollutant, has been widely detected in water environments, and has become a great concern in recent years. PFOS is very stable and difficult to decompose using conventional techniques. Sorption may be an attractive method to remove it from water. In this study, the molecularly imprinted polymer (MIP) adsorbents were prepared through the polymerization of 4-vinylpyridine under different preparation conditions in order to remove perfluorooctane sulfonate (PFOS) from water. The MIP adsorbents using perfluorooctanoic acid (PFOA) as the template had good imprinting effects and could selectively remove PFOS from aqueous solution. The sorption behaviors including sorption kinetics, isotherms, and effect of pH, salt, and competitive anions were investigated. Experimental results showed that the sorption of PFOS on the MIP adsorbents was very fast, pH-dependent, and highly selective. The achieved fast sorption equilibrium within 1 h was attributed to the surface sorption on the fine adsorbents. The sorption isotherms showed that the sorption selectivity of PFOS on the MIP adsorbents decreased at high PFOS concentrations, which may be due to the double-layer sorption and the formation of PFOS micelles on the sorbent surface. The sorption of PFOS on the MIP adsorbents was mainly dominated by the electrostatic interaction between the protonated vinylpyridine on the adsorbent surface and the anionic PFOS. The prepared MIP adsorbents can potentially be applied in water and wastewater treatment for selective removal of PFOS.     

聚电解质吸附特性的压电传感监测研究

在石英晶体微天平的电极表面修饰SiO2薄层,实时测定阳离子聚电解质均聚二甲基二烯丙基氯化铵在SiO2表面的吸附质量和吸附动力学过程,在此基础上,监测阴离子染料活性艳红K-2BP在预吸附聚电解质膜上的吸附过程,并讨论了溶液离子强度、pH值对聚电解质吸附特性的影响.     

絮凝剂P(AM-DMC)对活性艳红K-2BP的脱色作用

絮凝剂P(AM-DMC)对染料活性艳红K-2BP具有很好的脱色及去除CODCr性能,脱色率和CODCr去除率分别为97.18%、75.7%。脱色效果受絮凝剂用量、电荷密度、特性粘度、外加盐浓度及溶液pH值影响。红外光谱、可见吸收光谱及电荷量分析表明,P(AM-DMC)对活性艳红K-2BP的絮凝脱色过程中电荷中和起着重要作用,絮凝剂分子中的—N+(CH3)结构与染料分子中的-SO3-发生化学反应,同时也有分子间氢键形成,从而使水中染料分子聚集沉降。     

Higher sorption of arsenate versus arsenite on amorphous Al-oxide, effect of ligands

Arsenic pollution is currently a major health issue because As is toxic for human beings, animals, and plants. Knowledge of As mobility is therefore important to assess health risk. The sorption of arsenite and arsenate on metal oxides in the presence of various anionic ligands is closely linked to the mobility, bioavailability, and risk. It was reported that the sorption mechanisms and characteristics of arsenite and arsenate on Al-oxides were different from that on Fe-oxides. Previous work reports the sorption of arsenite and arsenate on Fe-oxides in the presence of ligands. Whereas there is few knowledge on the sorption of arsenite and arsenate by Al-oxides in the presence of ligands. Here, we studied the sorption of arsenite and arsenate on amorphous Al-oxide by batch experiments. We tested the effect of organic ligands: oxalate, malate, tartrate, citrate; and inorganic ligands: sulfate, phosphate, selenate, selenite. Results show that amorphous Al-oxide has more sorption affinity for arsenate than arsenite. The inhibition of As sorption by ligands at pH 6 is higher for arsenite than arsenate. For arsenite, the As sorption inhibition decreases in the order phosphate, citrate, malate, selenite, oxalate, tartrate, sulfate, and selenate. For arsenate, the As sorption inhibition decreases in the order phosphate, malate, citrate, selenite, tartrate, oxalate, sulfate, and selenate.     

Effect of dye auxiliaries on chemical oxygen demand and colour competitive removal from textile effluents using Posidonia oceanica

The use of an abundant and widely distributed seagrass species, Posidonia oceanica, as a biosorbent for the direct dye Yellow 44 was successfully shown. The studies were performed on the single dyestuff dissolved in water and in a dyebath containing agents commonly used in the textile industry, i.e. a surfactant (Lavotan TBU), a sequestring agent (Meropan DPE), a softening agent (Eurosoft CI10) and a salt (NaCl). The colour reduction results showed that P. oceanica was found to be more efficient for removal of Yellow 44 from an aqueous solution (162 mg g^?1) than from a dyebath solution (135 mg g^?1), according to the Langmuir isotherm model. For the single dyestuff sorption, Fourier transform infrared and X-ray photoelectron spectroscopy studies highlighted chemical sorption between the dye alcohol function and the sorbent acid function. The chemical oxygen demand removal percentages were found to be 54.9 and 76.6% for Yellow 44 dissolved in aqueous solution and in dyebath solution, respectively. This confirmed the both sorption of the chemical auxiliaries and the dye on P. oceanica.     

Influence of dissolved organic matter from corn straw on Zn andCusorption to Chinese loess

The interaction of Zn and Cu with dissolved organic matter (DOM) is a significant physicochemical process affecting their sorption as well as mobility in soil. The objective of this study was to examine the influence of DOM from corn straw on the sorption of Zn and Cu by loess through batch adsorption technique. The sorption isotherms of Zn and Cu could be well described by the Freundlich equation, and the partition distribution coefficient (k) in the presence of DOM was reduced by 86% for Zn and 58% for Cu, as compared to the control receiving no DOM, suggesting that DOM had a stronger inhibitory effect on Zn sorption than that of Cu. In addition, the sorption of metal increased with an increase in pH for loess, with maximum inhibition on metal sorption observed at pH > 7.6 for Zn and pH > 5.5 for Cu in the absence ofDOM but Cu sorption of DOM was suddenly decreased with an increase of pH at pH > 7.9 in the presence of DOM. At a DOM concentration of <200 mg L^?1, sorption of Zn and Cu was reduced by 46% for Zn and 32% for Cu with an increase in DOM concentration.     

Adsorption anionischer Azofarbstoffe an Boden/Sediment

The adsorption behavior of three anionic azo dyes (Acid Orange 6, Acid Orange 10 andAcid Orange 12) on different soil/sediment components (quartz sand, clay and organic matter) was investigated with a flow-through method using a simplified HPLC apparatus. Organic matter had the highest adsorption capacity for all three dyes, followed by clay and sand. The adsorption on different components in mixtures was not additive. The adsorption of similar aniomic azo dyes decreased with increasing negative charge. The affinity of equally charged dye molecules to the adsorbents was also strongly influenced by the remaining chemical structure. While adsorption on organic matter could always be described by Freundlich isotherms, S-shaped isotherms were often measured with quartz sand and clay. For that reason one must assume different adsorption mechanisms for organic matter and mineral adsorbens. Lower pH values always led to stronger adsorption of the anionic azo dyes. On the other hand, ionic strength effects cannot be characterized so clearly. Adsorption was generally lowered by decreasing ionic strengths but sometimes the opposite effect was observed. Moreover, there were some unusual cases of partly irreversible adsorption on quartz sand and organic matter when the dyes were not dissolved in an aqueous solution containing additional inorganic ions but in double distilled water. The adsorption of anionic azo dyes on soil and sediment materials turned out to be a very complex process. Although some interesting coherences could be pointed out, much more research is required to recognize general principles, concerning for example the influence of the chemical structure or the surrounding aqueous solution.     

黄河三角洲地区湿地土壤对多环芳烃的吸附特征

以黄河三角洲湿地土壤为对象,研究菲和苯并[a]芘(BaP)在土壤中的吸附特性.结果表明:菲和BaP在黄河三角洲地区湿地土壤的吸附速率都较快,均能在48h内达到平衡;土壤对菲和BaP的吸附等温线均呈线形,能较好地符合线性和Freundlich方程,样品经H2O2处理后对PAHs的吸附量明显降低,表明土壤中有机与无机矿物组分在吸附过程的作用不同;湿地土壤对多环芳烃的吸附明显存在固体效应,随着土壤颗粒物粒径和体系离子强度的增大,土壤的吸附容量都在降低.     

阴离子染料酸性大红GR水溶液的脱色及反应机理

以阴离子染料酸性大红GR为代表,采用十二胺做助剂,硫酸铝做混凝剂对其水溶液进行脱色处理,研究了助剂、混凝剂投加量、pH值及其盐效应等的影响．通过电导率、丁达尔效应和IR谱图分析其脱色机理：阴离子染料在水溶液中与十二胺之间发生化学反应,靠氢键和静电键结合,使染料微粒聚集形成胶体,再与硫酸铝混凝剂作用产生沉淀．