A K-band down-conversion mixer with 1.4-GHz bandwidth in 0.13-/spl mu/m CMOS technology

A low power and low voltage down conversion mixer working at K-band is designed and fabricated in a 0.13/spl mu/m CMOS logic process. The mixer down converts RF signals from 19GHz to 2.7GHz intermediate frequency. The mixer achieves a conversion gain of 1dB, a very low single side band noise figure of 9dB and third order intermodulation point of -2dBm, while consuming 6.9mW power from a 1.2V supply. The 3-dB conversion gain bandwidth is 1.4GHz, which is almost 50% of the IF. This mixer with small frequency re-tuning can be used for ultra-wide band radars operating in the 22-29GHz band.     

17-GHz 50-60 mW power amplifiers in 0.13-/spl mu/m standard CMOS

Two versions of power amplifiers with different output matching approaches for the 17-GHz band were realized in 0.13-/spl mu/m standard digital CMOS technology with 1.5-V supply voltage. The power amplifier with an external matching network delivers 17.8-dBm saturated output power with 15.6% power added efficiency (PAE). The small-signal gain is 11.5 dB. The fully integrated power amplifier delivers 17.1-dBm saturated output power with 9.3% PAE. The small-signal gain is 14.5 dB. No external radio frequency components are required.     

A 0.3-25-GHz ultra-wideband mixer using commercial 0.18-/spl mu/m CMOS technology

An ultra-wideband mixer using standard complementary metal oxide semiconductor (CMOS) technology was first proposed in this paper. This broadband mixer achieves measured conversion gain of 11 /spl plusmn/ 1.5 dB with a bandwidth of 0.3 to 25 GHz. The mixer was fabricated in a commercial 0.18-/spl mu/m CMOS technology and demonstrated the highest frequency and bandwidth of operation. It also presented better gain-bandwidth-product performance compared with that of GaAs-based HBT technologies. The chip area is 0.8 /spl times/ 1 mm/sup 2/.     

A 40 GHz single-ended down-conversion mixer in 0.13 /spl mu/m SiGeC BiCMOS HBT

This work presents a single-ended active mixer realized with a 0.13 /spl mu/m BiCMOS SiGeC heterojunction bipolar transistor (HBT) technology. This mixer is designed to be integrated in a superheterodyne receiver for 40 GHz wireless communication systems. Local oscillator (LO) and RF signals are directly applied to the base of the HBT through two coupled lines. The mixer provides a down-conversion from 42 GHz to 2 GHz. The mixer exhibits a power conversion gain better than 2.4 dB and a measured double-sideband noise figure less than 8.3 dB for P/sub LO/=3 dBm (power of the local oscillator) under a global power consumption lower than 9.5 mW. This architecture exhibits good linearity performance with a measured IP/sub 1dB/ of about -7 dBm and an IIP3 of +4 dBm. The linear dynamic range for a 2 GHz system bandwidth is approximately 65 dB for P/sub LO/=+2 dBm and T/sub 0/=290 K. The third order spurious free dynamic range is calculated to be better than 52 dB.     

Millimeter-wave voltage-controlled oscillators in 0.13-/spl mu/m CMOS technology

This paper describes the design of CMOS millimeter-wave voltage controlled oscillators. Varactor, transistor, and inductor designs are optimized to reduce the parasitic capacitances. An investigation of tradeoff between quality factor and tuning range for MOS varactors at 24 GHz has shown that the polysilicon gate lengths between 0.18 and 0.24 /spl mu/m result both good quality factor (>12) and C/sub max//C/sub min/ ratio (/spl sim/3) in the 0.13-/spl mu/m CMOS process used for the study. The components were utilized to realize a VCO operating around 60 GHz with a tuning range of 5.8 GHz. A 99-GHz VCO with a tuning range of 2.5 GHz, phase noise of -102.7 dBc/Hz at 10-MHz offset and power consumption of 7-15mW from a 1.5-V supply and a 105-GHz VCO are also demonstrated. This is the CMOS circuit with the highest fundamental operating frequency. The lumped element approach can be used even for VCOs operating near 100-GHz and it results a smaller circuit area.     

A low-power oscillator mixer in 0.18-/spl mu/m CMOS technology

A downconversion double-balanced oscillator mixer using 0.18-/spl mu/m CMOS technology is proposed in this paper. This oscillator mixer consists of an individual mixer stacked on a voltage-controlled oscillator (VCO). The stacked structure allows entire mixer current to be reused by the VCO cross-coupled pair to reduce the total current consumption of the individual VCO and mixer. Using individual supply voltages and eliminating the tail current source, the stacked topology requires 1.0-V low supply voltage. The oscillator mixer achieves a voltage conversion gain of 10.9 dB at 4.2-GHz RF frequency. The oscillator mixer exhibits a tuning range of 11.5% and a single-sideband noise figure of 14.5 dB. The dc power consumption is 0.2 mW for the mixer and 2.94 mW for the VCO. This oscillator mixer requires a lower supply voltage and achieves a higher operating frequency among recently reported Si-based self-oscillating mixers and mixer oscillators. The mixer in this oscillator mixer also achieves a low power consumption compared with recently reported low-power mixers.     

A 2-GHz carrier leakage calibrated direct-conversion WCDMA transmitter in 0.13-/spl mu/m CMOS

A highly integrated 2-GHz, 0.13-/spl mu/m CMOS direct-conversion transmitter for wide-band code division multiple access (WCDMA) is described. Different circuit and calibration techniques are presented that successfully suppress the carrier leakage and enable the direct-upconversion architecture to meet all WCDMA specifications. The transmitter delivers +2.5 dBm output power while consuming only 45 mA from its nominal 1.5-V supply. The overall gain can be programmed in 1-dB steps over a 100-dB range with 0.4 dB accuracy. The transmitter achieves an OIP3 of +19.3 dBm, an error vector magnitude of 4.3%, and an adjacent channel leakage ratio of -38 dBc. The measured output noise of -146 dBm/Hz in the DCS Rx band and -149 dBm/Hz in the UMTS Rx band is sufficiently low to provide an option to increase the integration level even further by eliminating the external Tx interstage filter between the power amplifier and its driver.     

A 40-GHz frequency divider in 0.18-/spl mu/m CMOS technology

An analysis of regenerative dividers predicts the required phase shift or selectivity for proper operation. A divider topology is introduced that employs resonance techniques by means of on-chip spiral inductors to tune out the device capacitances. Configured as two cascaded /spl divide/2 stages, the circuit achieves a frequency range of 2.3 GHz at 40 GHz while consuming 31 mW from a 2.5-V supply.     

15-GHz fully integrated nMOS switches in a 0.13-/spl mu/m CMOS process

Two fully integrated nMOS switches have been demonstrated at 15 GHz in a 0.13-/spl mu/m CMOS foundry process. One incorporates on-chip LC impedance transformation networks (ITNs) while the second one does not. The switches with and without ITNs achieve the same 1.8-dB insertion loss at 15 GHz, but 21.5 and 15 dBm input P/sub 1dB/, respectively. The degradation of insertion loss due to use of ITNs is compensated by reducing the mismatch loss caused by the bond pad parasitics. The switch without ITNs is suitable for 3.1-10.6 GHz ultra-wide-band (UWB) applications. The switch with ITNs has /spl sim/5 dB worse isolation than the switch without. The difference is due to the larger transistor size of the switch with ITNs, which introduces lower parasitic impedance path between Tx/Rx ports and antenna port.     

50 Gbit/s 2:1 multiplexer in 0.13 /spl mu/m CMOS technology

A fully integrated 2:1 multiplexer IC which operates at up to 50 Gbit/s data rate is presented. The MUX uses inductive shunt peaking and an output series inductor for higher bandwidth. The MUX directly drives the 50 /spl Omega/ load. The IC is fabricated in a 0.13 /spl mu/m bulk CMOS technology and draws 65 mA at 1.5 V supply voltage. The output voltage swing is 2/spl times/100 mV.     

A miniature Q-band low noise amplifier using 0.13-/spl mu/m CMOS technology

A miniature Q-band low noise amplifier (LNA) using 0.13-/spl mu/m standard mixed signal/radio frequency complementary metal-oxide-semiconductor (CMOS) technology is presented in this letter. This three-stage common source thin-film microstrip LNA achieves a peak gain of 20dB at 43GHz with a compact chip size of 0.525mm/sup 2/. The 3-dB frequency bandwidth ranges from 34 to 44GHz and the minimum noise figure is 6.3dB at 41GHz. The LNA outperforms all the reported commercial standard CMOS Q-band LNAs, with the highest gain, highest output IP3, and smallest chip size.     

A low-voltage folded-switching mixer in 0.18-/spl mu/m CMOS

Scaling of CMOS technologies has a great impact on analog design. The most severe consequence is the reduction of the voltage supply. In this paper, a low voltage, low power, AC-coupled folded-switching mixer with current-reuse is presented. The main advantages of the introduced mixer topology are: high voltage gain, moderate noise figure, moderate linearity, and operation at low supply voltages. Insight into the mixer operation is given by analyzing voltage gain, noise figure (NF), linearity (IIP3), and DC stability. The mixer is designed and implemented in 0.18-/spl mu/m CMOS technology with metal-insulator-metal (MIM) capacitors as an option. The active chip area is 160 /spl mu/m/spl times/200 /spl mu/m. At 2.4 GHz a single side band (SSB) noise figure of 13.9 dB, a voltage gain of 11.9 dB and an IIP3 of -3 dBm are measured at a supply voltage of 1 V and with a power consumption of only 3.2 mW. At a supply voltage of 1.8 V, an SSB noise figure of 12.9 dB, a voltage gain of 16 dB and an IIP3 of 1 dBm are measured at a power consumption of 8.1 mW.     

A 15-GHz broad-band /spl divide/2 frequency divider in 0.13-/spl mu/m CMOS for quadrature generation

This letter presents a 0.13-/spl mu/m CMOS frequency divider realized with an injection-locking ring oscillator. This topology can achieve a larger input frequency range and better phase accuracy with respect to injection-locking LC oscillators, because of the smoother slope of the loop gain phase-frequency plot. Post layout simulations show that the circuit is able to divide an input signal spanning from 7 to 19GHz, although the available tuning range of the signal source limited the experimental verification to the interval 11-15GHz, featuring a 31% locking range. The divider dissipates 3mA from a 1.2-V power supply.     

A 20-GHz phase-locked loop for 40-gb/s serializing transmitter in 0.13-/spl mu/m CMOS

A 20-GHz phase-locked loop with 4.9 ps/sub pp//0.65 ps/sub rms/ jitter and -113.5 dBc/Hz phase noise at 10-MHz offset is presented. A half-duty sampled-feedforward loop filter that simply replaces the resistor with a switch and an inverter suppresses the reference spur down to -44.0 dBc. A design iteration procedure is outlined that minimizes the phase noise of a negative-g/sub m/ oscillator with a coupled microstrip resonator. Static frequency dividers made of pulsed latches operate faster than those made of flip-flops and achieve near 2:1 frequency range. The phase-locked loop fabricated in a 0.13-/spl mu/m CMOS operates from 17.6 to 19.4GHz and dissipates 480mW.     

A 3-to-8-GHz fast-hopping frequency synthesizer in 0.18-/spl mu/m CMOS technology

A frequency synthesizer incorporating one single-sideband (SSB) mixer generates seven bands of clock distributed from 3 to 8GHz with 1-ns switching time. An efficient frequency synthesizing technique producing balanced bands around one center frequency is employed, and the SSB mixer uses double degeneration topology to increase the linearity. Fabricated in 0.18-/spl mu/m CMOS technology, this circuit achieves a sideband rejection of 37 dB while consuming 48 mW from a 2.2-V supply.     

A 0.35-/spl mu/m CMOS 2-GHz VCO in wafer-level package

This letter presents a complementary metal oxide semiconductor (CMOS) voltage-controlled oscillator (VCO) with a high-Q inductor in a wafer-level package for the LC-resonator. The on-chip inductor is implemented using the redistribution metal layer of the wafer-level package (WLP), and therefore it is called a WLP inductor. Using the thick passivation and copper metallization, the WLP inductor has high quality-factor (Q-factor). A 2-nH inductor exhibits a Q-factor of 8 at 2 GHz. The center frequency of the VCO is 2.16 GHz with a tuning range of 385 MHz (18%). The minimum phase noise is measured to be -120.2 dBc/Hz at an offset frequency of 600 kHz. The dc power consumed by the VCO-core is 1.87 mW with a supply voltage of 1.7 V and a current of 1.1 mA. The output power with a 50-/spl Omega/ load is -12.5/spl plusmn/1.3 dBm throughout the whole tuning range. From the best of our knowledge, compared with recently published 2-GHz-band 0.35 /spl mu/m CMOS VCOs in the literature, the VCO in this work shows the lowest power consumption and the best figure-of-merit.     

A 5.9-GHz voltage-controlled ring oscillator in 0.18-/spl mu/m CMOS

This paper presents the design of three- and nine-stage voltage-controlled ring oscillators that were fabricated in TSMC 0.18-/spl mu/m CMOS technology with oscillation frequencies up to 5.9 GHz. The circuits use a multiple-pass loop architecture and delay stages with cross-coupled FETs to aid in the switching speed and to improve the noise parameters. Measurements show that the oscillators have linear frequency-voltage characteristics over a wide tuning range, with the three- and nine-stage rings resulting in frequency ranges of 5.16-5.93 GHz and 1.1-1.86 GHz, respectively. The measured phase noise of the nine-stage ring oscillator was -105.5 dBc/Hz at a 1-MHz offset from a 1.81-GHz center frequency, whereas the value for the three-stage ring oscillator was simulated to be -99.5 dBc/Hz at a 1-MHz offset from a 5.79-GHz center frequency.     

50-GHz optically injection-locked 1.55-/spl mu/m VCSELs

High-speed directly modulated diode lasers are important for optical communications and optical interconnects. In this work, we demonstrate greatly enhanced resonance frequency for vertical-cavity surface-emitting lasers, from 7 to 50 GHz, under ultrahigh injection-locking conditions. In addition, a 20-dB gain is achieved for small signal modulation below resonance frequency.     

A 32-GHz non-uniform distributed amplifier in 0.18-/spl mu/m CMOS

This letter presents a fully integrated distributed amplifier in a standard 0.18-/spl mu/m CMOS technology. By employing a nonuniform architecture for the synthetic transmission lines, the proposed distributed amplifier exhibits enhanced performance in terms of gain and bandwidth. Drawing a dc current of 45mA from a 2.2-V supply voltage, the fabricated circuit exhibits 9.5-dB pass-band gain with a bandwidth of 32GHz while maintaining good input and output return losses over the entire frequency band. With a compact layout technique, the chip size of the distributed amplifier including the testing pads is 940/spl times/860/spl mu/m/sup 2/.     

A 1.8-V 2.4/5.15-GHz dual-band LCVCO in 0.18-/spl mu/m CMOS technology

A dual band, fully integrated, low phase-noise and low-power LC voltage-controlled oscillator (VCO) operating at the 2.4-GHz industrial scientific and medical band and 5.15-GHz unlicensed national information infrastructure band has been demonstrated in an 0.18-/spl mu/m CMOS process. At 1.8-V power supply voltage, the power dissipation is only 5.4mW for a 2.4-GHz band and 8mW for a 5.15-GHz band. The proposed VCO features phase-noise of -135dBc/Hz at 3-MHz offset frequency away from the carrier frequency of 2.74GHz and -126dBc/Hz at 3-MHz offset frequency away from 5.49GHz. The oscillator is tuned from 2.2 to 2.85GHz in the low band (2.4-GHz band) and from 4.4 to 5.7GHz in the high band (5.15-GHz band).