Synthesis and humidity sensitive properties of nanocrystalline Ba1−xSrxTiO3 thick films

Nanocrystalline Ba_1−xSr_xTiO₃ (x=0, 0.2, 0.4, 0.6, 0.8 and 1.0) precursors were synthesized using the stearic acid gel method. After the precursors had been calcined at 600–950°C for 0.5–1 h, nanocrystalline powders with the cubic perovskite structure were obtained and these were made into thick films. The powder samples were characterized by differential thermal analysis, X-ray diffraction and transmission electron microscopy, and the thick film samples were characterized by scanning electron microscopy and X-ray diffraction. The humidity-sensitive properties of the nanocrystalline Ba_1−xSr_xTiO₃ thick films were investigated. The results show that these nanocrystalline thick films possess higher humidity sensitivity and lower resistance than those of conventional materials.     

Spectroscopic ellipsometry analysis of GaAs1 − xNx layers grown by molecular beam epitaxy

In this work, we present the effect of nitrogen incorporation on the dielectric function of GaAsN samples, grown by molecular beam epitaxy (MBE) followed by a rapid thermal annealing (for 90 s at 680 °C). The GaAs_1 − xN_x samples with N content up to 1.5% (x = 0.0%, 0.1%, 0.5%, 1.5%), are investigated using room temperature spectroscopic ellipsometry (SE). The optical transitions in the spectral region around 3 eV are analyzed by fitting analytical critical point line shapes to the second derivative of the dielectric function. It was found that the features associated with E₁ and E₁ + Δ₁ transitions are blue-shifted and become less sharp with increasing nitrogen incorporation, in contrast to the case of E₀ transition energy in GaAs_1 − xN_x. An increase of the split-off Δ₁ energy with nitrogen content was also obtained, in agreement to results found with MOVPE GaAs_1 − xN_x grown samples.     

Structural and optical properties of (100 − x)(Li2B4O7) − x(SrO–Bi2O3–0.7Nb2O5–0.3V2O5) glasses and glass nanocrystal composites

Glasses of various compositions in the system (100 − x)(Li₂B₄O₇) − x(SrO–Bi₂O₃–0.7Nb₂O₅–0.3V₂O₅) (10  x  60, in molar ratio) were prepared by splat quenching technique. The glassy nature of the as-quenched samples was established by differential thermal analyses (DTA). The amorphous nature of the as-quenched glasses and crystallinity of glass nanocrystal composites were confirmed by X-ray powder diffraction studies. Glass composites comprising strontium bismuth niobate doped with vanadium (SrBi₂(Nb_0.7V_0.3)₂O_9−δ (SBVN)) nanocrystallites were obtained by controlled heat-treatment of the as-quenched glasses at 783 K for 6 h. High resolution transmission electron microscopy (HRTEM) of the glass nanocrystal composites (heat-treated at 783 K/6 h) confirm the presence of rod shaped crystallites of SBVN embedded in Li₂B₄O₇ glass matrix. The optical transmission spectra of these glasses and glass nanocrystal composites of various compositions were recorded in the wavelength range 190–900 nm. Various optical parameters such as optical band gap (E_opt), Urbach energy (ΔE), refractive index (n), optical dielectric constant and ratio of carrier concentration to the effective mass (N/m^*) were determined. The effects of composition of the glasses and glass nanocrystal composites on these parameters were studied.     

Optical and electrical properties of p-type AgInSnxS2−x (x = 0–0.04) thin films prepared by spray pyrolysis

AgInSn_xS_2−x (x = 0–0.2) polycrystalline thin films were prepared by the spray pyrolysis technique. The samples were deposited on glass substrates at temperatures of 375 and 400 °C from alcoholic solutions comprising silver acetate, indium chloride, thiourea and tin chloride. All deposited films crystallized in the chalcopyrite structure of AgInS₂. A p-type conductivity was detected in the Sn-doped samples deposited at 375 °C, otherwise they are n-type. The optical properties of AgInSn_xS_2−x (x < 0.2) resemble those of chalcopyrite AgInS₂. Low-temperature PL measurements revealed that Sn occupying an S-site could be the responsible defect for the p-type conductivity observed in AgInSn_xS_2−x (x < 2) thin films.     

Optical absorption and emission properties of Er doped mixed alkali borosilicate glasses

This paper presents the optical absorption and luminescence properties of Er³⁺ doped mixed alkali borosilicate glasses: 59.5SiO₂ · 20B₂O₃ · xLi₂O · (20 − x)Na₂O · 0.5Er₂O₃ and 59.5SiO₂ · 20B₂O₃ · xLi₂O · (20 − x)K₂O · 0.5Er₂O₃, with x = 0, 4, 8, 12, 16 and 20 mol%. The variations of Judd–Ofelt intensity parameters (Ω₂, Ω₄, and Ω₆), hypersensitive transition intensities, total radiative transition probability (A_T), radiative lifetimes (τ_R), integrated absorption cross-sections (Σ) and stimulated emission cross-sections (σ_p) as a function of x are discussed in detail. The changes in Ω₂ and intensities of hypersensitive transitions are attributed to optical basicity changes in the host glass matrix, which leads to variations in the covalency of the Er–O bond. The luminescence properties are reported for certain transitions, and the emission cross-section is high at x = 8–12 in the case of lithium sodium glass, whereas in lithium potassium glass it is high at x = 8.     

Preparation and optical properties of sol–gel derived Er-doped Al2O3–Ta2O5 films

Thin films of the system xAl₂O₃–(100 − x)Ta₂O₅–1Er₂O₃ were prepared by a sol–gel method and a dip-coating technique. The influences of the composition and the crystallization of the films on Er³⁺ optical properties were investigated. Results of X-ray diffraction indicated that the crystallization temperature of Ta₂O₅ increased from 800 to 1000 °C with increased values of x. In crystallized films, the intensities of the visible fluorescence and upconversion fluorescence tend to decrease with an increase in x values, due to the high phonon energy of Al₂O₃; the strongest fluorescence is observed in a crystallized film for x = 4 heat treated at 1000 °C. In amorphous films obtained by heat treatment at relatively low temperatures the Er³⁺ fluorescence could not be observed because strong fluorescence from organic residues remaining in the films thoroughly covered the Er³⁺ fluorescence. On the other hand, the Er³⁺ upconversion fluorescence in the amorphous films was observed to be stronger than that in the crystallized films. The strongest upconversion fluorescence is observed in an amorphous film for x = 75 heat treated at 800 °C.     

Characterization of CuIn1 − xAlxS2 thin films prepared by thermal evaporation

Ingots containing single crystals of the quaternary alloys CuIn_1 − xAl_xS₂ (CIAS) were grown by a horizontal Bridgman method for compositions with x = 0, 0.2 and x = 0.4. (CIAS) thin films were prepared by thermal evaporation technique on to glass substrates. Structural and optical properties of the films were studied in function of the Al content. Band gap, and absorption coefficients were determined from the analysis of the optical spectra (transmittance and reflectance as a function of wavelength) recorded by a spectrophotometer. The samples have direct bandgap energies of 1.95 eV (x = 0), 2.06 eV (x = 0,2) and 2.1 eV (x = 0,4). These optical results were correlated with the structural analysis by X-Ray diffraction.     

Optical band gap studies on xPb3O4–(1−x)P2O5 lead[(II, IV)] phosphate glasses

A series of glasses in the xPb₃O₄–(1−x)P₂O₅ (red lead phosphate) (RLP) system with ‘x' varying from 0.075 to 0.4 were prepared by the single-step melt quenching process from Pb₃O₄ and NH₄H₂PO₄. The optical absorption spectra of these glasses have been recorded in the ultraviolet region from 200 to 400 nm and the fundamental absorption edges have been identified. The optical band gap E_opt values have been determined for all the glasses using the known theories. The (E_opt) values vary from 4.90 to 3.21 eV the highest being 4.57 eV, corresponding to the most stable glass of x=0.225. The absorption edge is attributed to the indirect transitions and the origin of the Urbach energy ΔE is suggested to be thermal vibrations. These glasses promise as potential candidates for application in optical technology compared to simple xPbO–(1−x)P₂O₅ (lead phosphate) (LP) glasses.     

YNixMn1−xO3 thin films by pulsed laser deposition: Structure and magnetic properties

Highly oriented YNi_xMn_1−xO₃ thin films on SrTiO₃ (100) substrates were achieved by using pulsed laser deposition for x = 0.33 and x = 0.50. We used a combination of X-ray diffraction, scanning electron microscopy, atomic force microscopy, and magnetic-property measurements. The magnetic transition temperatures (T_c) of the as-grown films are higher than the corresponding bulk values (typically 85 K instead of 80 K, for x = 0.5, and 60 K instead of 50 K, for x = 0.33). Our magnetic measurements also suggest a spin-glass characteristic in the x = 0.33 films, while a cluster glasslike behavior is observed for the films with x = 0.5, which is quite different from that of the bulk samples. Finally, the influence of post-deposition heat treatment on the magnetic properties of the as-grown films is discussed.     

Dielectric and piezoelectric properties of sol–gel derived Ca doped PbTiO3

Synthesis of Ca doped PbTiO₃ powder by a chemically derived sol–gel process is described. Crystallization characteristics of different compositions Pb_1−xCa_xTiO₃ (PCT) with varying calcium (Ca) content in the range x = 0–0.45 has been investigated by DTA/TGA, X-ray diffraction and scanning electron microscopy. The crystallization temperature is found to decrease with increasing calcium content. X-ray diffraction reveals a tetragonal structure for PCT compositions with x ≤ 0.35, and a cubic structure for x = 0.45. Dielectric properties on sintered ceramics prepared with fine sol–gel derived powders have been measured. The dielectric constant is found to increase with increasing Ca content, and the dielectric loss decreases continuously. Sol–gel derived Pb_1−xCa_xTiO₃ ceramics with x = 0.45 after poling exhibit infinite electromechanical anisotropy (k_t/k_p) with a high d₃₃ = 80 pC/N, ′ = 298 and low dielectric loss (tan δ = 0.0041).     

Sintering behavior and microwave dielectric properties of Bi3(Nb1−xTax)O7 solid solutions

Solid solutions of Bi₃(Nb_1−xTa_x)O₇ (x = 0.0, 0.3, 0.7, 1) were synthesized using solid state reaction method and their microwave dielectric properties were first reported. Pure phase of fluorite-type could be obtained after calcined at 700 °C (2 h)⁻¹ between 0 ≤ x ≤ 1 and Bi₃(Nb_1−xTa_x)O₇ ceramics could be well densified below 990 °C. As x increased from 0.0 to 1.0, saturated density of Bi₃(Nb_1−xTa_x)O₇ ceramics increased from 8.2 to 9.1 g cm⁻³, microwave permittivity decreased from 95 to 65 while Q_f values increasing from 230 to 560 GHz. Substitution of Ta for Nb modified temperature coefficient of resonant frequency τ_f from −113 ppm °C⁻¹ of Bi₃NbO₇ to −70 ppm °C⁻¹ of Bi₃TaO₇. Microwave permittivity, Q_f values and τ_f values were found to correlate strongly with the structure parameters of fluorite solid solutions and the correlation between them was discussed in detail. Considering the low densified temperature and good microwave dielectric proprieties, solid solutions of Bi₃(Nb_1−xTa_x)O₇ ceramics could be a good candidate for low temperature co-fired ceramics application.     

Physical properties of (La,Sr)Ti(O,N)3 thin films grown by pulsed laser deposition

Thin films of La_xSr_1−xTiO_3+x/2 (x = 0, 0.25, 0.5, 0.75, 1) were grown by laser ablation on two different kinds of substrates (SrTiO₃ (STO) and MgO) and were subsequently ammonolysed to yield the corresponding oxynitrides La_xSr_1−xTi(O,N)₃. For both substrates all films were found to grow epitaxially to the (1 0 0) direction of the cubic perovskite structure, except for x = 0.5 that grew parallel to the (1 1 0) direction. For some of the films TiN was detected as impurity phase. Scanning electron microscopy revealed that the films are dense and homogeneous with thicknesses around 350 nm. Atomic force microscopy showed that the surface roughness of the films varied between 4.2 and 14.1 nm. The employed substrate had a strong influence on the electrical properties. Films grown on STO exhibited a metallic behaviour, in contrast to the films grown on MgO, which were insulating.     

Structure and electrical properties of boron-added (Ba,Sr)TiO3 thin films fabricated by the sol-gel method

Thin films of Ba_xSr_1−xTiO₃ (BST, with x=0.5) were fabricated on a RuO₂/Ru/SiO₂/Si substrate by the spin coating of the multicomponent sol prepared using metal alkoxides. Boron alkoxide was intentionally introduced to establish a better microstructure and to reduce the leakage current. AFM indicated that a crack-free uniform microstructure having a smooth surface was gradually developed with increasing boron content. The relative dielectric permittivity of the 250-nm thick BST thin films fired at 700°C decreased with increasing content of boron, from 420 for the undoped film to 190 for the 10 mol% boron-added film at 1 MHz. This observation was interpreted in terms of a serial capacitance composed of the perovskite BST grain and the interfacial B₂O₃ glassy phase having a low dielectric permittivity. The leakage current density (J) also decreased with the amount of boron added. The leakage current for the applied voltage greater than 1 V showed a linear variation of logJ with E^1/2 at room temperature, suggesting that the interface-controlled Schottky emission was the dominant conduction process for the BST thin films fabricated on the RuO₂ electrode.     

Thermal nonlinear refraction in the dye-doped sol–gel xTiO2 · (100 − x)SiO2 system

The build-up time of the thermal lens effect induced by a Gaussian beam in the DO3-doped sol–gel system xTiO₂ · (100 − x)SiO₂ at different compositions, both in the liquid and gel phases has been measured in a Z-scan geometry. While the pure titania samples show a minimum of the thermal diffusivity, a maximum is found for x ≈ 30. The sol to gel transformation leads to an increase of the build-up times at all compositions.     

Mechanical characterization of Ni1−xZnxFe2O4 prepared by non-conventional methods

The mechanical properties like hardness, H_v and compressive strength, σ of Ni_1−xZn_xFe₂O₄ (x = 0.2, 0.3, 0.4 and 0.5) prepared by the non-conventional flash combustion and citrate-gel decomposition techniques are studied and reported. It is observed that there is an increase in hardness with zinc content as well as sintering temperature. The hardness in the order of 2.0–3.63 GPa and compressive strength in the order of 150–240 MPa are obtained for Ni–Zn ferrites prepared by these non-conventional techniques. The influence of density, porosity and microstructure on hardness and compressive strength of Ni–Zn ferrites with respect to sintering temperature was studied.     

Influence of rare-earth oxides on structure and crystallization properties of Bi2O3–B2O3 glass

Bi₂O₃·B₂O₃ glasses doped with rare-earth oxides (RE₂O₃) (RE³⁺ = La³⁺, Pr³⁺, Sm³⁺, Gd³⁺, Er³⁺ and Yb³⁺) were prepared by the melting–quenching method. The relationships between composition and properties were demonstrated by IR, DSC, XRD and SEM analysis. The results show that the network structure resembles that of undoped Bi₂O₃·B₂O₃ glass, composing of [BO₃], [BO₄] and [BiO₆] units. RE₂O₃ stabilizes the glass structure as a modifier. Transition temperature (T_g) increases linearly with cationic field strength (CFS) of RE³⁺. La₂O₃, Pr₂O₃, Sm₂O₃ and Gd₂O₃ are benefit to promote the formation of BiBO₃ crystal. When Er₂O₃ and Yb₂O₃ are introduced, respectively, the main crystal phase changes to Bi₆B₁₀O₂₄. Transparent surface crystallized samples are obtained by reheating at 460–540 °C for 5 h. In this case, needle like BiBO₃ crystal or rare-earth-doped BiBO₃ crystal (Pr_xBi_1−xBO₃ and Gd_xBi_1−xBO₃) are observed, which is promising for non-linear optical application.     

High-resolution and analytical transmission electron microscopy of epitaxial YBa2Cu3O7−x thin films and YBa2Cu3O7/PrBa2Cu3O7 superlattices

Transmission electron microscopy (TEM) studies of epitaxial YBa₂Cu₃O_7−x thin films and YBa₂Cu₃O₇/PrBa₂Cu₃O₇ superlattices are summarized. High-resolution imaging of cross-sections and plan views and energy-dispersive X-ray microanalysis and electron energy loss spectroscopy in the transmission electron microscope were the methods applied. In the first section results on YBa₂Cu₃O_7−x thin films With varying oxygen stoichiometry deposited onto SrTiO₃ are discussed. Then, YBa₂Cu₃O₇/PrBa₂Cu₃O₇ superlattices deposited onto SrTiO₃ and MgO are investigated. Finally, an interface analysis of high-quality YBa₂Cu₃O_7−x thin films deposited onto sapphire with yttrium-stabilized zirconia buffer layers is presented.     

Doping and electrical characteristics of in-situ heavily B-doped Si1−x−yGexCy films epitaxially grown using ultraclean LPCVD

Doping and electrical characteristics of in-situ heavily B-doped Si_1−x−yGe_xC_y (0.22<x<0.6, 0<y<0.02) films epitaxially grown on Si(100) were investigated. The epitaxial growth was carried out at 550°C in a SiH₄–GeH₄–CH₃SiH₃–B₂H₆–H₂ gas mixture using an ultraclean hot-wall low-pressure chemical vapor deposition (LPCVD) system. It was found that the deposition rate increased with increasing GeH₄ partial pressure, and only at high GeH₄ partial pressure did it decrease with increasing B₂H₆ as well as CH₃SiH₃ partial pressures. With the B₂H₆ addition, the Ge and C fractions scarcely changed and the B concentration (C_B) increased proportionally. The C fraction increased proportionally with increasing CH₃SiH₃ partial pressures. These results can be explained by the modified Langmuir-type adsorption and reaction scheme. In B-doped Si_1−x−yGe_xC_y with y=0.0054 or below, the carrier concentration was nearly equal to C_B up to approximately 2×10²⁰ cm⁻³ and was saturated at approximately 5×10²⁰ cm⁻³, regardless of the Ge fraction. The B-doped Si_1−x−yGe_xC_y with high Ge and C fractions contained some electrically inactive B even at the lower C_B region. Resistivity measurements show that the existence of C in the film enhances alloy scattering. The discrepancy between the observed lattice constant and the calculated value at the higher Ge and C fraction suggests that the B and C atoms exist at the interstitial site more preferentially.     

Investigation on the cross sensitivity of NO2 sensors based on In2O3 thin films prepared by sol-gel and vacuum thermal evaporation

In₂O₃ thin films have been prepared from commercially available pure In₂O₃ powders by high vacuum thermal evaporation (HVTE) and from indium iso-propoxide solutions by sol-gel techniques (SG). The films have been deposited on sapphire substrates provided with platinum interdigital sputtered electrodes. The as-deposited HVTE and SG films have been annealed at 500°C for 24 and 1 h, respectively. The film morphology, crystalline phase and chemical composition have been characterised by SEM, glancing angle XRD and XPS techniques. After annealing at 500°C the films’ microstructure turns from amorphous to crystalline with the development of highly crystalline cubic In₂O_3−x (JCPDS card 6-0416). XPS characterisation has revealed the formation of stoichiometric In₂O₃ (HVTE) and nearly stoichiometric In₂O_3−x (SG) after annealing. SEM characterisation has highlighted substantial morphological differences between the SG (highly porous microstructure) and HVTE (denser) films. All the films show the highest sensitivity to NO₂ gas (0.7–7 ppm concentration range), at 250°C working temperature. At this temperature and 0.7 ppm NO₂ the calculated sensitivities (S=R_g/R_a) yield S=10 and S=7 for SG and HVTE, respectively. No cross sensitivity have been found by exposing the In₂O₃ films to CO and CH₄. Negligible H₂O cross has resulted in the 40–80% relative humidity range, as well as to 1 ppm Cl₂ and 10 ppm NO. Only 1000 ppm C₂H₅OH has resulted to have a significant cross to the NO₂ response.     

In situ co-precipitation synthesis and photoluminescence of YxGd1−xVO4:Tm microcrystalline phosphors by hybrid precursors

Y_xGd_1−xVO₄:Tm³⁺ (5 mol%) phosphors were prepared by in situ co-precipitation technology with the different content ratio of Y/Gd (x = 0.2, 0.3, 0.4, 0.5, 0.6, 0.8, respectively). During the process, rare earth coordination polymers with o-hydroxylbenzoate were used as precursors, composing with polyethylene glycol (PEG) as dispersing media. After heat-treatment of the resulting multicomponent hybrid precursors at 900 °C, the samples were obtained. SEM indicated the particles present good crystalline state, whose crystalline grain sizes were about 0.2–2 μm. Under the excitation of 257 nm, all the materials show the characteristic emission of Tm³⁺ which is the strong blue emission centered at 475 nm originating from ¹G₄ → ³H₆ of Tm³⁺. Besides this, concentration quenching appears in the system of YVO₄:Tm³⁺ and GdVO₄:Tm³⁺. And when x reaches 0.5, the system of Y_xGd_1−xVO₄:Tm³⁺ shows the strongest blue emission.