用于日盲波段的MgZnO薄膜材料和紫外探测器

考虑ZnO优秀的物理和化学性能以及由于生长温度低而具有更低的缺陷密度从而易于实现高的光电器件效率等特点，本文采用射频磁控溅射和金属有机化学汽相沉积（MOCVD）方法在石英及蓝宝石衬底上生长了立方结构MgZnO薄膜，制备了MgZnO的MSM型紫外探测器。该器件实现了在日盲（太阳盲）波段的光响应，典型的光响应峰值分别在225和250nm，截止边为230和273nm。     

Ultrashort-pulse investigation of the propagation properties of the LP(11) mode in 1.55-mum communication fibers

The coupling of an ultrashort laser pulse into a single-mode optical communication fiber gives rise to two propagating pulses as a result of the excitation of two guided modes, the fundamental, LP(01) , and the leaky, LP(11) . Such a phenomenon provides a new approach to the study of the propagation properties of the LP(11) mode. An experiment with tunable 110-fs pulses at a wavelength near 1550 nm is described. Information about the group velocity, the polarization-rotation length, the attenuation coefficient, and the cutoff wavelength of the LP(11) mode is obtained in a simple and direct way for various fibers.     

空气孔辅助光纤的模式截止

光纤的截止波长是光纤设计的重要参量之一。利用全矢量正交函数模型对空气孔辅助光纤的模式截止特性进行了讨论。分析表明：由于光纤包层中存在空气孔,即使不考虑材料色散,包层的有效折射率也与波长有关;包层有效折射率由包层中空气孔的大小和波长决定,与芯子的掺杂浓度无关。在所研究的波长范围之内,与传统的w型光纤类似,在包层中空气孔的相对尺寸d／Λ较大时出现了基模截止现象。d／Λ从0．2到0．9变化时,光纤的各阶模式的截止波长都随之减小;各阶模式的截止波长随d／Λ变化曲线的斜率随模式阶次的升高而降低。     

少模多芯光纤的纤芯排布方法

提出一种3模12芯光纤的纤芯排布优化方法.在分析芯间串扰、弯曲半径阈值和相对纤芯多重性因子等特性后,给出了单圆形结构和方点阵结构的纤芯排布方法及优化方案.对于单圆形结构,在波长为1 625nm的情况下很难找到合适纤芯排布以使芯间串扰小于-30dB/100km并且使光缆截至波长小于1 530nm.对于方点阵结构,在波长为1 625nm,且弯曲半径大于弯曲半径阈值时,可使芯间串扰小于-30dB/100km,最大光缆截至波长不大于1 530nm,纤芯多重性因子可达到~15,这表明方点阵结构是一种比单圆形结构更适合3模12芯光纤的纤芯排布结构.     

Doped photonic bandgap fibers for short-wavelength nonlinear devices

Microstructured photonic bandgap fibers with a doped honeycomb cladding structure and the guiding defect defined by the absence of doping are proposed as nonlinear optical fibers for short wavelengths. It is shown that zero-dispersion wavelengths below 500 nm and corresponding effective areas of 1-2 microm2 can be obtained if structures with interhole distances near 600 nm can be fabricated. The cutoff wavelength for guidance of second-order modes can be controlled by variation of the radius and index contrast of the doped regions.     

Cutoff Wavelength Measurement for Single Mode Optical Fibers with Computer-generated Matched Filter

１ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｃｕｔｏｆｗａｖｅｌｅｎｇｔｈ，ａｔｗｈｉｃｈｔｈｅｆｉｒｓｔｈｉｇｈｅｒｏｒｄｅｒｍｏｄｅｄｉｓａｐｐｅａｒｓ，ｉｓｏｎｅｏｆｔｈｅｍｏｓｔｉｍｐｏｒｔａｎｔｐａｒａｍｅｔｅｒｓｆｏｒａｓｉｎｇｌｅｍｏｄｅｏｐｔｉ...     

Crystal growth and characterization of l-phenylalaninium trichloroacetate—A new organic nonlinear optical material

Amino acid based crystals exhibit excellent nonlinear and electro-optical properties. A new nonlinear optical single crystal l-phenylalaninium trichloroacetate (LPTCA) belonging to the amino acid group was grown by the slow evaporation solution growth method. The grown crystals have been subjected to powder X-ray diffraction studies to identify the crystalline nature. Single crystal X-ray diffraction study showed that LPTCA belongs to monoclinic crystal system. Fourier transform infrared study is used to confirm the presence of various functional groups in the grown crystal. Optical transparency of the grown crystals was investigated by UV-vis-NIR spectrum. The lower optical cutoff wavelength for this crystal is observed at 254 nm and energy band gap is 4.89 eV. Thermal properties of the LPTCA crystal were studied by thermogravimetric analysis (TGA) and differential thermal analysis (DTA) techniques, which indicate that the material does not decompose before melting. The melting point of grown crystal was observed to be 136 °C in a melting point apparatus. The existence of nonlinear optical (NLO) property of LPTCA was confirmed by second harmonic generation test using Nd:YAG laser fundamental wavelength of 1064 nm.     

W型单模单偏振光纤基模截止的条件

给出了 W型单模单偏振光纤基模截止的必要条件。通过对基模截止波长的数值计算 ,分析了这个必要条件的充分性。结论是 :对于圆形内包层 W型光纤来说 ,这是必要的而又充分的条件 ;对于低椭圆度内包层 W型单模单偏振光纤来说 ,它可以在较高的精度上近似作为充分条件 ,而对于高椭圆度内包层 W型单模单偏振光纤来说 ,它仅仅只是必要条件而非充分条件     

Ultrabroad-band wavelength converter with high flattening conversion efficiency in a semiconductor optical amplifier

The efficiency of ultrabroad-band wavelength conversion using orthogonal-pump four-wave mixing in a semiconductor optical amplifier is measured for the wavelength shifts from 1500 to 1640 nm. The variation of conversion efficiency is ＜ 0.9 dB over the wavelength range from 1530 to 1560 nm (C-band), and ＜ 4.5dB over the wavelength range from 1560 to 1610 nm (L-band). The maximum conversion efficiency is about -8.7 dB.     

飞秒激光空气等离子体发射光谱的实验研究

对强飞秒激光聚焦在空气中所激发的等离子体的发射光谱进行了实验研究.结果表明,光谱特征表现为短波段(截至波长为340 nm)强烈的连续谱和长波段(波长在800 nm附近)强度相对较低的线光谱.在脉冲宽度(50 fs)保持不变而不断调节激光脉冲能量时,等离子体光谱形状的特征基本相似;当激光脉冲能量(1 mJ)保持不变而脉冲宽度从50 fs增加至500 fs和1 ps时,连续谱的峰值(500 nm)显得格外突出,并开始呈现出线光谱特征. 关键词： 飞秒激光 激光空气等离子体 发射光谱 线光谱     

Photoemission electron microscopy as a tool for the investigation of optical near fields

Photoemission electron microscopy was used to image the electrons photoemitted from specially tailored Ag nanoparticles deposited on a Si substrate (with its native oxide SiO(x)). Photoemission was induced by illumination with a Hg UV lamp (photon energy cutoff homega(UV) = 5.0 eV, wavelength lambda(UV) = 250 nm) and with a Ti:sapphire femtosecond laser (homega(l) = 3.1 eV, lambda(l) = 400 nm, pulse width below 200 fs), respectively. While homogeneous photoelectron emission from the metal is observed upon illumination at energies above the silver plasmon frequency, at lower photon energies the emission is localized at tips of the structure. This is interpreted as a signature of the local electrical field therefore providing a tool to map the optical near field with the resolution of emission electron microscopy.     

Wavelength-spacing tunable multi-wavelength fiber optical parametric oscillator based on multiple four-wave mixing

We propose a wavelength-spacing tunable multi-wavelength fiber optical parametric oscillator (MW-FOPO) with a simple line cavity and one pump source based on multiple four-wave mixing (MFWM). Stable multi-wavelength lasing at room temperature is achieved due to the four-wave mixing effect and the broadband gain of the fiber optical parametric amplifier based on a highly nonlinear fiber. The wavelength spacing of the proposed MW-FOPO can be tuned by adjusting the wavelength of the pump light or the central wavelength of the fiber Bragg grating. Seventeen lasing lines with a wavelength spacing of 2.89 nm and an extinction ratio larger than 10 dB, which covers the wavelength region from 1540 to 1568 nm is demonstrated.     

Optical properties of MnAl films

The optical properties of MnAl films of different compositions, deposited at different substrate temperatures and in the thickness range 25 to 90 nm, are reported. The reflectance and transmittance are measured in the wavelength range 320–900 nm for near normal incidence of light. These measurements are used to calculate the optical constants namely, refractive index (n) and extinction coefficient (k). The wavelength and thickness dependence of these optical constants are reported. The optical measurements for films with higher Mn content and grown at higher substrate temperature reveal that n and k values are constant over a wide wavelength range (500–900 nm) showing high reflectance in the visible and near infrared region.     

重铬酸盐明胶反射全息图的波长调节新技术研究

介绍了一种采用有机预膨胀剂调节李普曼反射全息图再现波长的新方法. 将水溶性的有机试剂丙稀酰胺作为预膨胀剂均匀加入亚甲基蓝敏化的重铬酸盐明胶（MBDCG）溶液中来制作全息干板,预膨胀剂在反射全息图的后处理阶段溶于水,明胶层发生均匀收缩,从而使再现波长向短波方向移动. 通过控制丙稀酰胺浓度,可在整个可见光区大范围定量控制再现波长.     

Study of mode propagation with 632.8-nm laser in tapered fiber

The material dispersion of a tapered fiber is described by Sellmeier＇s equation. The dependence of refractive index on wavelength and doping concentration is discussed. A He-Ne laser with the output wavelength of 632.8 nm is used in the experiment. When the cutoff frequency of the fiber is less than the laser frequency, the guiding modes of a singl~-mode fiber （at 1550 am） are investigated. The results show that the original single-mode fiber becomes a multi-mode waveguide. The propagation and mode coupling of the light in the taper region are analyzed. By controlling the taper end size of the fiber, the unique tapered fiber can convert a multi-mode beam into a single-mode one.     

基于半导体光放大器瞬态交叉相位调制效应的高速反相和同相波长转换的研究

采用半导体光放大器(SOA)中的瞬态交叉相位调制效应是实现高速全光信号处理的有效途径.利用SOA和带宽为0.4 nm的窄带滤波器同时实现了重复频率为10 GHz、脉冲宽度为10 ps的同相和反相全光波长转换.当滤波器的中心波长相对于探测光载波波长蓝移0.25 nm或者红移0.05 nm时，得到反相波长转换；当滤波器的中心波长相对于探测光波长蓝移0.29 nm或者红移0.25 nm时，得到同相的波长转换.同时用数值模拟了从同相到反相波长转换的极性演化过程，理论分析和实验结果基本相符. 关键词： 半导体光放大器 波长转换 瞬态交叉相位调制     

Spatial optical filter sensor based on hollow-core silica tube

A spatial optical filter based on a hollow-core silica tube is proposed. Because of the hollow-core dimensions, it is possible to obtain a periodical spatial filter ranging from 1200 to 1700 nm with a channel spacing of 2.64 THz. The bandwidth is approximately 5.32 nm, and the isolation loss is ~30 dB. The optical losses are approximately ~0.67 dB/mm for a wavelength of 1500 nm. The 40 mm long spatial optical filter is tested as a sensing element and subjected to different physical parameters. The spatial optical filter is wavelength sensitive to strain and temperature, while for refractive-index variations there is an optical power dependency. This fiber structure can be used as a sensing element for extreme conditions, such as in very high temperature environments, where it presents a sensitivity of 27.5 pm °C(-1).     

双泵浦光子晶体光纤参量放大研究

利用光子晶体光纤在不同零色散波长附近具有不同色散的特性,研究了在零色散波长为780 nm和1550 nm附近的双泵浦光子晶体光纤参量放大过程.在780 nm附近,讨论了零色散波长变化对双泵浦光子晶体光纤参量放大的影响.数值模拟结果表明:当零色散波长发生微小的变化时,信号增益谱带宽会发生很大的变化.当两泵浦光之间的波长差值减小时,零色散波长的变化对参量放大的影响在很大程度上可以得到抑制,但是增益带宽会有一定的减小.依据这一原理,在1550 nm附近设计光子晶体光纤中的色散平坦光纤参量放大,在5 m长的光子晶体光纤中,当峰值功率为10 W时,得到了增益为65 dB,带宽达到420 nm且极为平坦的增益谱.     

多孔氧化铝薄膜的制备和光学特性研究

采用阳极氧化法制备了二维有序纳米孔氧化铝膜.研究了工艺参数对多孔薄膜有序性、孔径、膜厚度等的影响，测量了多孔氧化铝有序膜的光透过、光吸收和光发射等光学特性.结果表明，在波长360 nm附近多孔氧化铝有序膜的光透过谱线和光吸收谱线发生突变，波长大于360 nm时，光透过增强；波长小于360 nm时，光吸收增强.多孔氧化铝有序膜的光致发光强度和峰位与激发光波长有关，光致发光谱范围在340~600 nm.     

Four-wave mixing in dual wavelength fiber laser utilizing SOA for wavelength conversion

In this paper, a novel configuration of a wavelength converter is set forth by utilizing a semiconductor optical amplifier (SOA) as a nonlinear gain medium to generate a four-wave mixing (FWM) effect by using a dual wavelength bi-erbium-doped fiber laser that uses an Arrayed Waveguide Grating (AWG) together with two optical channel selector (OSC) as selective elements to function as a dual wavelength switchable pump power. The four-wave mixing (FWM) is produced with a wavelength detuning of 7 nm from the pump and signal which used is as the converted signal at wavelength 1532.8 nm or 1534.5 nm for transferring data from the input signal at wavelength 1547.0 nm. Thus, even though the conversion efficiency is as low as −43 dB, it is still possible for applications as a wavelength converter.