焙烧温度对Ni/CaO-Al_2O_3结构及其催化重整性能的影响

采用共沉淀法制备了一系列具有类水滑石结构前驱体的Ni/CaO-Al_2O_3复合催化剂,考察了制备过程中焙烧温度对复合催化剂结构及性能的影响。结果表明,焙烧温度可调控活性组分Ni与载体之间的相互作用力,进而调变复合催化剂的比表面积、活性组分Ni的颗粒粒径。当焙烧温度为700℃时,Ni与载体之间相互作用力适宜,复合催化剂具有最大的比表面积(21.42 m~2/g)和最小的Ni颗粒粒径(19.51 nm);该复合催化剂在CO_2吸附强化CH_4/H_2O重整制氢过程中可得到98.31%的H_2浓度和94.87%的CH_4转化率,循环10次后,H_2浓度仍能保持在97.35%以上。这是因为大的比表面积为反应提供了更多的活性位点,利于CO_2吸附过程的强化,而小的Ni颗粒粒径提高了复合催化剂的抗烧结能力。     

等离子体技术对CO2甲烷化用Ni/SiO2催化剂的改性作用

采用浸渍法制备了Ni/SiO₂催化剂,应用等离子体技术对催化剂进行改性处理。以CO₂甲烷化为模型反应对催化剂进行活性评价,通过H₂程序升温还原(H₂-TPR)和CO₂程序升温脱附(CO₂-TPD)技术对催化剂进行表征。研究了等离子体技术强化处理对催化剂吸附性能和还原性能的影响。结果表明,与常规焙烧的催化剂相比,等离子体技术改性处理提高了催化剂活性组分的分散度,增加反应活性位并调变了活性位对吸附物种的吸附强度,改进了催化剂的还原性能,CO₂甲烷化反应活性和甲烷的时空产率显著提高。     

制备条件对Ni/ZrO2-SiO2催化剂煤气甲烷化的影响

采用浸渍法制备了ZrO₂-SiO₂复合载体和Ni质量分数为6%的Ni/ZrO₂-SiO₂催化剂,考察了载体制备时浸渍溶液pH值、焙烧温度和催化剂制备时的焙烧温度对Ni/ZrO₂-SiO₂催化剂煤气甲烷化反应性能的影响。采用X射线衍射、程序升温还原和扫描电子显微镜等方法对催化剂进行了表征。结果表明,载体浸渍溶液pH值为8.0～9.0, 载体焙烧温度为550 ℃,催化剂焙烧温度为450 ℃时,Ni/ZrO₂-SiO₂催化剂在煤气甲烷化反应中显示了最优的催化性能,CO转化率100%,CO₂转化率1.8%,CH₄生成速率16.6 mmol/(h·g)。进一步表征发现,制备ZrO₂-SiO₂复合载体时,增大浸渍溶液的pH值有利于形成粒径较小的亚稳态四方晶相ZrO₂,可见四方晶相ZrO₂更有利于甲烷化反应;载体焙烧温度会影响到NiO粒径的大小和其在催化剂表面的分散,温度过高和过低都会导致NiO粒径大小的不适宜以及分散性的降低;催化剂焙烧温度过高则会导致NiO与载体间的相互作用减弱,NiO分散性降低。     

制备方法对 Ni-Al2O3催化剂在 CO2-CH4重整反应中 催化性能的影响

为提高镍基催化剂的干法重整活性,采用溶液燃烧法、等体积浸渍法、胶体磨循环浸渍法和水热-沉积法制备了SCM、IMP、T310和HTP四种催化剂,在800 ℃考察了其在CO₂-CH₄重整反应中的催化性能,并结合ICP-AES、N₂吸附-脱附、XRD、H₂-TPR和TEM等表征手段对催化剂进行分析。结果表明,水热-沉积法和胶体磨循环浸渍法制备的催化剂比表面积较大,分别为190.83和182.21 m²/g,可为反应提供较多的接触面积,进而提高催化剂的初始活性(HTP试样CH₄和CO₂初始转化率相对较高,分别达85.15%和90.84%);而溶液燃烧法和等体积浸渍法制备的催化剂具有较多的NiAl₂O₄尖晶石,其还原峰面积占总还原峰面积90%以上,还原后可获得更多晶粒粒径更小的稳定活性组分Ni(SCM和IMP试样稳定性更好,反应50 h后活性超过HTP和T310试样,100 h后CH₄转化率方降至50%以下)。因此,决定催化剂稳定活性的更重要的因素应该是活性组分Ni晶粒粒径的大小及其抗烧结能力的强弱。     

制备方法对甲烷干重整催化剂Ni/La2O3/Al2O3结构及性能的影响

采用浸渍法及蒸发法制备了Ni/La₂O₃/Al₂O₃催化剂,考察了制备方法对其结构及甲烷干重整催化性能的影响。通过XRD、H₂ TPR、BET、TEM、TG-DSC等方法对催化剂进行了表征。结果表明,浸渍法制备的催化剂具有较好的Ni分散性、更均匀的粒径分布,较大的比表面积及更优的孔结构,从而具有更好的Ni抗烧结能力及抗积炭性。浸渍法制备的催化剂平均积炭速率很低,约为0.6737mg/(g_cat·h),相当于蒸发法制备催化剂的21%。活性测试结果表明,浸渍法制备的催化剂上CH₄、CO₂转化率及H₂、CO选择性比蒸发法制备的催化剂分别高约5%、10%及4%、3%,具有更好的稳定性。     

CoAl2O4/Al2O3载体对钴基费托催化剂反应性能影响的研究

通过浸渍和高温焙烧,制得表面附着CoAl₂O₄微晶颗粒的改性Al₂O₃载体,并采用等体积浸渍法制备负载型Co基催化剂。结合 N₂物理吸附、XRD、H₂-TPR、XPS及H₂化学吸附等表征手段,研究改性载体及其负载钴基催化剂的织构特征;采用费托合成反应评价其催化性能。结果表明,Al₂O₃改性后,表面CoAl₂O₄的存在有效减少了载体与活性组分Co的相互作用,显著提高了催化剂的还原度和催化活性。载体的改性量在20%左右达到最佳值,继续增加,催化剂还原度和活性基本不再升高。载体改性促使催化剂CH₄选择性有所降低,C₅₊选择性略有提高。     

Ni-Co/TiO2增强CO2加氢反应性能的研究

通过浸渍-沉淀法合成负载型双金属催化剂Ni-Co/TiO₂,采用X射线衍射(XRD)、场发射扫描电子显微镜(FESEM)、X射线能谱(EDS)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)和氮气吸附-脱附(BET)对其晶型、形貌、组成、表面元素价态和比表面积进行表征.在CO₂加氢反应中,Ni-Co/Ti O₂催化剂在3 h反应时间内生成84.4μmol CH₄,相较于Ni/Ti O₂催化剂,其CH₄产量提高了46.3%.二氧化碳程序升温脱附(CO₂-TPD)和氢气程序升温还原(H₂-TPR)测试结果证实,Co的引入能增强Ni-Co/Ti O₂对CO₂的吸附和活化,从而促进其加氢反应效率的提高.经过5次循环活性测试,Ni/Ti O₂的活性降低了20.5%,而Ni-Co/Ti O₂的活性仅仅降低了10.9%,这表明Co的引...     

负载Ni催化剂用于乙二醇蒸汽重整制氢催化性能研究

采用等体积浸渍法和共沉淀法制备了Ni催化剂,在固定床反应器上考察了Ni负载量、焙烧温度、反应温度等因素对乙二醇低温重整制氢反应活性和选择性的影响。应用X射线衍射、氮物理吸附、H₂程序升温还原等技术对负载型Ni催化剂进行了表征。结果表明,共沉淀法制备的Ni/CeO₂催化剂具有较小的NiO颗粒与CeO₂载体颗粒粒径,催化活性较高。添加少量氧化钴到Ni/CeO₂催化剂中可使H₂收率达72.6%,EG转化率达93.1%。在CeO₂中添加Al₂O₃能提高负载Ni催化剂的活性,乙二醇转化率达94.0%,H₂收率达67.0%;但添加SiO₂则使其活性明显变差。     

柠檬酸对MoO3/CeO2-Al2O3催化剂耐硫甲烷化性能的影响

将柠檬酸（CA）作为络合剂添加至CeO₂-Al₂O₃复合载体中,并考察了CA对MoO₃/CeO₂-Al₂O₃催化剂耐硫甲烷化性能的影响。活性评价结果显示,催化剂活性随柠檬酸添加量的增大而增大,当n（CA）/n（Ce）为3时,CO转化率可达60%。催化剂BET、XRD、H₂-TPR及XPS等表征结果表明,在CeO₂-Al₂O₃复合载体中加入CA,可以增大载体及催化剂的比表面积,使Mo物种分散性提高。同时,CA对Ce物种起络合作用,致使催化剂表面Ce元素含量明显增加,进而减弱了活性组分Mo物种与载体间相互作用力,并最终导致了催化剂活性的提升。     

Ca/Al物质的量比对Ni/CaO-Al_2O_3结构及其催化重整性能的影响

合成兼具催化、吸附性能的复合催化剂是实现CO_2吸附强化CH_4/H_2O重整制氢过程的关键。研究采用共沉淀法制备了一系列具有类水滑石结构前驱体的Ni/Ca O-Al_2O_3复合催化剂,考察了制备过程中Ca/Al物质的量比对复合催化剂结构及性能的影响。结果表明,Ca/Al物质的量比可调控活性组分Ni与载体之间的相互作用力,进而调变复合催化剂的比表面积和活性组分Ni的分散度。当Ca/Al物质的量比为3时,Ni与载体之间相互作用力适宜,复合催化剂具有最大的比表面积(12.9 m~2/g)和最高的Ni分散度(1.07%);该复合催化剂在CO_2吸附强化CH_4/H_2O重整制氢过程中可得到95%的H_2浓度和88%的CH_4转化率,循环10次后,H2浓度仍能保持在93%以上。     

Characterization of La-promoted Ni/Al2O3 catalysts for hydrogen production from glycerol dry reforming

In the current paper, dry (CO₂)-reforming of glycerol, a new reforming route, was carried out over alumina (Al₂O₃)-supported, non-promoted and lanthanum-promoted nickel (Ni) catalysts. Both sets of catalysts were synthesized via a wet co-impregnation procedure. Physicochemical characterization of the catalysts showed that the promoted catalyst possessed smaller metal crystallite size, hence higher metal dispersion compared to the virgin Ni/Al₂O₃ catalyst. This was also corroborated by the surface images captured by the FESEM analysis. From temperature-programmed calcination analysis, the derivative weight profiles revealed two peaks, which represent a water elimination peak at a temperature range of 373 to 473 K followed by nickel nitrate decomposition from 473 to 573 K. In addition, BET surface area measurements gave 85.0 m²·g⁻¹ for the non-promoted Ni catalyst, whilst the promoted catalysts showed an average of 1% to 6% improvement depending on the La loadings. Significantly, reaction studies at 873 K showed that glycerol dry reforming successfully produced H₂. The 2%La-Ni/Al₂O₃ catalyst, which possessed the largest BET surface area, gave an optimum H₂ generation (9.70%) at a glycerol conversion of 24.5%.     

柠檬酸辅助固相研磨法制备铜基催化剂及在CO_2加氢合成甲醇反应中的性能研究

通过柠檬酸辅助固相研磨法制备铜基催化剂,采用XRD、TPR、TG-DSC、SEM、BET、TEM、XPS、CO_2-TPD等手段对催化剂性能进行表征.结果表明室温固相研磨的前驱体在惰性气体N_2中焙烧使体系中的CuO绝大部分被原位还原成Cu~0,不需外加H_2还原,直接制得了C/I-Cu/ZnO催化剂,催化剂具有中孔.利用高压固定床连续反应装置对催化剂活性进行了评价,结果表明,柠檬酸用量、前驱体焙烧温度、焙烧升温速率等条件对催化剂活性产生影响,当C_6H_8O_7/(Cu+Zn)摩尔比为1.2/1并Cu/Zn摩尔比1/1,前驱体在N_2中以3 K·min~(-1)升温速率于623 K焙烧3 h,制得的C/I-Cu/ZnO催化剂比表面积最大,Cu~0粒径最小,在CO_2加氢合成甲醇反应中表现出最佳的活性,CO_2转化率、甲醇选择性和产率分别达到了28.28%、74.29%和21.01%.与外加H_2还原的C/H-Cu/ZnO催化剂相比,原位还原C/I-Cu/ZnO催化剂比表面积较大,Cu~0的粒径较小,活性较高.     

Ni/Al2O3 catalysts for CO methanation: Effect of Al2O3 supports calcined at different temperatures

The correlation between phase structures and surface acidity of Al₂O₃ supports calcined at different temperatures and the catalytic performance of Ni/Al₂O₃ catalysts in the production of synthetic natural gas (SNG) via CO methanation was systematically investigated. A series of 10 wt% NiO/Al₂O₃ catalysts were prepared by the conventional impregnation method, and the phase structures and surface acidity of Al₂O₃ supports were adjusted by calcining the commercial γ-Al₂O₃ at different temperatures (600–1200 °C). CO methanation reaction was carried out in the temperature range of 300–600 °C at different weight hourly space velocities (WHSV = 30000 and 120000 mL·g^?1·h^?1) and pressures (0.1 and 3.0 MPa). It was found that high calcination temperature not only led to the growth in Ni particle size, but also weakened the interaction between Ni nanoparticles and Al₂O₃ supports due to the rapid decrease of the specific surface area and acidity of Al₂O₃ supports. Interestingly, Ni catalysts supported on Al₂O₃ calcined at 1200 °C (Ni/Al₂O₃-1200) exhibited the best catalytic activity for CO methanation under different reaction conditions. Lifetime reaction tests also indicated that Ni/Al₂O₃-1200 was the most active and stable catalyst compared with the other three catalysts, whose supports were calcined at lower temperatures (600, 800 and 1000 °C). These findings would therefore be helpful to develop Ni/Al₂O₃ methanation catalyst for SNG production.     

Cu-Ni-Al尖晶石催化甲醇水蒸气重整制氢性能的研究

以氢氧化铜、醋酸镍和拟薄水铝石为原料,通过固相法合成了Cu-Ni-Al尖晶石催化剂。采用N2物理吸附、XRD、H2-TPR和XPS等表征方法,研究Cu/Ni/Al的物质的量比和焙烧温度对催化剂的比表面积、物相、还原性能以及表面性质的影响,并以甲醇水蒸气重整制氢为探针反应,考察催化剂的缓释催化性能。结果表明,随着焙烧温度的升高,Cu-Ni-Al催化剂的尖晶石含量增加,但尖晶石晶粒增大,且比表面积下降。不同的焙烧温度和Cu/Ni/Al物质的量比,所得催化剂的比表面积、还原性能和表面性质不同,从而表现出不同的缓释催化性能。与计量比Cu/Al=1∶2的合成比较,Cu/Al=1∶3形成了非计量比的富Al尖晶石固溶体,生成的晶体粒子小、比表面积和孔容大、难还原的尖晶石部分增多,呈现出更好的缓释催化性能。甲醇制氢反应性能评价结果显示,Cu-Ni-Al尖晶石在反应条件下逐渐释放活性铜而催化反应的进行,其中,CNA3-1000催化剂表现中最高的催化活性和稳定性。     

Al2O3催化剂结构对催化臭氧化活性的影响

以Al₂O₃为催化剂催化臭氧化处理邻苯二甲酸二甲酯. 通过XRD、比表面积、孔结构、FTIR和活性评价等方法对催化剂的物化性质及催化活性进行了研究, 考察了焙烧温度、成型粒径对催化剂活性的影响. 结果表明, Al₂O₃催化剂对臭氧化降解邻苯二甲酸二甲酯具有很高的催化活性, 反应120 min后, 总有机碳(TOC)的去除率从单独臭氧氧化的23.9%提高到55.1%; 焙烧温度对催化剂的活性具有很大的影响, 600 ℃催化剂催化活性最高; 随着焙烧温度的升高, Al₂O₃晶型经历了从γ-Al₂O₃到θ-Al₂O₃到α-Al₂O₃的转变, 催化剂的比表面积、焙烧得到的孔容逐渐变小, 晶体粒径变大, 表面•OH数量减少, 催化活性下降. Al₂O₃成型粒径的减小, 提高了催化剂的外比表面积, 减小了内部传质扩散的影响, 从而提高了催化活性.     

Novel Ni/CeO2-Al2O3 composite catalysts synthesized by one-step citric acid complex and their performance in catalytic partial oxidation of methane

A series of novel Ni/CeO2-Al2O3composite catalysts were synthesized by one-step citric acid complex method. The as-synthesized catalysts were characterized by N2physical adsorption/desorption, X-ray diffraction(XRD), Fourier transform infrared(FT-IR) spectroscopy, hydrogen temperature-programmed reduction(H2-TPR), X-ray photoelectron spectroscopy(XPS) and thermogravimetry analysis(TGA). The effects of nickel content, calcination and reaction temperatures, gas hourly space velocity(GHSV) and inert gas dilution of N2on their performance of catalytic partial oxidation of methane(CPOM) were investigated. Catalytic activity test results show that the highest methane conversion(85%), the best selectivities to carbon monoxide(87%) and to hydrogen(95%), the excellent stability and perfect H2/CO ratio(2.0) can be obtained over Ni/CeO2-Al2O3with 8 wt% Ni content calcined at 700 ℃ under the reaction condition of 750 ℃, CH4/O2ratio of 2 : 1 and gas hourly space velocity of 12000 mL h-1 g-1. Characterization results show that the good catalytic performance of this composite catalyst can be contributed to its large specific surface area(～108 m2 g-1), small crystallite size, easy reducibility and low coking rate.     

CO oxidation over Co3O4/SiO2 catalysts: Effects of porous structure of silica and catalyst calcination temperature

The catalytic performances of Co3O4/SiO2 catalysts prepared by incipient wetness impregnation for CO oxidation were investigated using three kinds of silica as carriers with different pore sizes of 7.7, 14.0 and 27.0 nm. The effects of calcination temperature on the catalyst surface and micro structure properties as well as catalytic performance for the oxidation of carbon monoxide were also studied. All catalysts were characterized by N2 adsorption-desorption, XRD, XPS, FTIR, H2-TPR and O2-TPD. It was found that the properties and crystal size of cobalt-containing species strongly depended on the pore size of silica carrier. While the silica pore size increased from 7.7 to 27.0 nm, the Co3O4 crystal size increased from 8.5 to 13.5 nm. Moreover, it was demonstrated that if the spinel crystal structure of Co3O4 was obtained at a calcination temperature as low as 150 ℃, the catalyst sample would have a high Co3O4 surface dispersion and a increase of surface active species, and thus exhibit a high activity for the oxidation of carbon monoxide.     

Effect of Calcination Temperature and Pretreatment with Reaction Gas on Properties of Co/γ‐Al2O3 Catalysts for Partial Oxidation of Methane

The effects of calcination temperature and feedstock pretreatment on the catalytic performance of Co/γ‐Al₂O₃ catalysts were studied for partial oxidation of methane (POM) to synthesis gas, with emphasis on the role of feedstock pretreatment. The physicochemical properties of the catalysts were characterized by N₂ adsorption, X‐ray diffraction (XRD), transmission electron microscopy (TEM), H₂ temperature‐programmed reduction (H₂‐TPR), and Raman spectroscopy. The results showed that the pretreatment of the catalyst by reaction gas significantly improved the catalytic activity and stability for the POM reaction. On the other hand, the effect of calcination temperature was less significant. Although the initial activity was increased by an increased calcination temperature, the catalyst without the feedstock pretreatment suffered a rapid deactivation. The reaction‐atmosphere pretreatment was revealed as a process that mainly modified the surface structure of the catalyst. In that process, the formation of a CoAl₂O₄‐like compound led to high Co metal dispersion after reduction, and the transformation of the carrier into α‐Al₂O₃ occurred over the catalyst surface. Both the high dispersion of cobalt and the presence of α‐Al₂O₃ surface phase were assumed as the important factors resulting in an excellent catalytic performance in terms of high activity and high stability.     

不同载体Ni基负载型催化剂对甲烷部分氧化制合成气催化行为研究

采用浸渍法制备了单一载体(Al₂O₃、ZrO₂、CeO₂)和ZrO₂、CeO₂改性的Al₂O₃复合载体的Ni催化剂,考察了在甲烷部分氧化制备合成气反应中的催化性能。通过N₂-物理吸附、H₂程序升温还原、X射线衍射、NH₃程序升温脱附和程序升温氧化等技术对催化剂进行了表征。结果表明,在单一载体催化剂中,Ni/Al₂O₃具有较大的比表面积,其初始反应活性较高,但该催化剂表面易形成大量的积炭而快速失活。Ni/ZrO₂和Ni/CeO₂催化剂比表面积较小,活性金属Ni在其表面分散性差,催化剂具有较低的CH₄转化率。而CeO₂和ZrO₂改性的Al₂O₃复合载体催化剂,具有较大的比表面积,反应活性明显高于单一载体催化剂。CeO₂-Al₂O₃复合载体催化剂具有最高的反应活性和较好的反应稳定性。同时表明,含CeO₂催化剂反应后表面积炭较少,CeO₂的储放氧功能增强了催化剂对O₂的活化,提高催化剂活性的同时,可以抑制积炭的生成。