Evaluation of hot corrosion behavior of CSZ,CSZ/micro Al2O3 and CSZ/nano Al2O3 plasma sprayed thermal barrier coatings

Hot corrosion is one of the main destructive factors in thermal barrier coatings (TBCs) which come as a result of molten salt effect on the coating–gas interface. Hot corrosion behavior of three types of plasma sprayed TBCs was evaluated: usual CSZ, layer composite of CSZ/Micro Al₂O₃ and layer composite of CSZ/Nano Al₂O₃ in which Al₂O₃ was as a topcoat on CSZ layer. Hot corrosion studies of plasma sprayed thermal barrier coatings (TBCs) were conducted in 45 wt% Na₂SO₄+55 wt% V₂O₅ molten salt at 1050 °C for 40 h. The graded microstructure of the coatings was examined using scanning electron microscope (SEM) and X-ray diffractometer (XRD) before and after hot corrosion test. The results showed that no damage and hot corrosion products was found on the surface of CSZ/Nano Al₂O₃ coating and monoclinic ZrO₂ fraction was lower in CSZ/Micro Al₂O₃ coating in comparison with usual CSZ. reaction of molten salts with stabilizers of zirconia (Y₂O₃ and CeO₂) that accompanied by formation of monoclinic zirconia, irregular shape crystals of YVO₄, CeVO₄ and semi-cubic crystals of CeO₂ as hot corrosion products, caused the degradation of CSZ coating in usual CSZ and CSZ/Micro Al₂O₃ coating.     

Composite Ni/Al2O3 coatings and their corrosion resistance

Composite coatings Ni/Al₂O₃ were electrochemically deposited from a Watts bath. Al₂O₃ powder with particle diameter below 1 μm was codeposited with the metal. The obtained Ni/Al₂O₃ coatings contained 5-6% by weight of corundum. The structure of the coatings was examined by scanning electron microscopy (SEM). It has been found that the codeposition of Al₂O₃ particles with nickel disturbs the nickel coating's regular surface structure, increasing its microcrystallinity and surface roughness. DC and AC electrochemical tests were carried out on such coatings in a 0.5 M solution of Na₂SO₄ in order to evaluate their corrosion resistance. The potentiodynamic tests showed that the corrosion resistance of composite coating Ni/Al₂O₃ is better than that of the standard nickel coating. After 14 days of exposure the nickel coating corrodes three times faster than the Ni/Al₂O₃ coating. The electrochemical behaviour of the coatings in the corrosive solution was investigated by electrochemical impedance spectroscopy (EIS). An equivalent circuit diagram consisting of two RC electric circuits: one for electrode, nickel corrosion processes and the other for processes causing coating surface blockage, were adopted for the analysis of the impedance spectra. The changes in the charge transfer resistance determined from the impedance measurements are comparable with the changes in corrosion resistance determined from potentiodynamic measurements.     

Electrochemical anticorrosion performance evaluation of Al2O3 coatings deposited by MOCVD on an industrial brass substrate

Alumina (Al₂O₃) coatings of different thickness were deposited on OT59 brass substrate (BS) using the metal organic chemical vapour deposition (MOCVD) technique to evaluate the corrosion performance by EIS measurements. The used precursor was dimethyl-aluminium-isopropoxide. Electrochemical characterizations of the deposited films were performed in a standard very aggressive acidic solution (aerated 1N H₂SO₄ at 25 °C up to 168 h of immersion time) by means of direct current method (Tafel curves) and electrochemical impedance spectroscopy (EIS). The Rutherford backscattering spectroscopy (RBS) indicated that the films are very pure with the correct Al₂O₃ stoichiometry, while the IR absorption spectra showed that the films did not contain any OH groups. The surface film morphology was investigated by atomic force microscopy (AFM) and displayed a globular texture. The films were very smooth, with a maximum root mean square roughness, for example, of 14 nm for a 0.96 μm thick coating. The EIS data confirmed, as expected, that a 2.40 μm Al₂O₃ layer ensures the best corrosion protection after 168 h of immersion in the very acidic environment used.     

The preparation of Cu-coated Al2O3 composite powders by electroless plating

Cu-coated Al₂O₃ composite powders were synthesized by using the electroless plating method. The influence of the components proportion and the pH value of the plating solution on the Cu layer were analyzed with XRD and SEM. The results showed that the proportion of the plating solution components plays an important role for synthesizing the Al₂O₃/Cu composite powders. The content of copper in the composite powders could be effectively controlled by adjusting the content of copper sulfate and formaldehyde in the plating solution. Furthermore, the pretreatment of the Al₂O₃ powders is also a key factor to form a uniform Cu layer coating Al₂O₃ particles. The optimum technical parameters for producing Al₂O₃/Cu composite powders with uniform Cu coat were obtained.     

Laser machining of Al2O3-ZrO2 (3%Y2O3) eutectic composite

In this work we present the study of the interaction between NIR pulsed laser and Al₂O₃-ZrO₂ (3%Y₂O₃) eutectic composite. The effect produced by modifying the reference position as well as the working conditions and laser beam features has been studied when the samples are processed by means of pulse bursts.The samples were obtained by the laser floating zone technique using a CO₂ laser system. The laser machining was carried out with a Q-switched Nd:YAG laser at its fundamental wavelength of 1064 nm with pulse-widths in the nanosecond range.Geometric dimensions, i.e. ablated depth, machined width and removed volume as well as ablation yield of the resulting holes have been studied. We have described and discussed the morphology, composition and microstructure of the processed samples.     

Phase diagram of the Al2O3-HfO2-Y2O3 system

The phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system was first constructed in the temperature range 1200-2800 °C. The phase transformations in the system are completed in eutectic reactions. No ternary compounds or regions of appreciable solid solution were found in the components or binaries in this system. Four new ternary and three new quasibinary eutectics were found. The minimum melting temperature is 1755 °C and it corresponds to the ternary eutectic Al₂O₃ + HfO₂ + Y₃Al₅O₁₂. The solidus surface projection, the schematic of the alloy crystallization path and the vertical sections present the complete phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system.     

Al2O3-coated SnO2/TiO2 composite electrode for the dye-sensitized solar cell

A novel Al₂O₃-coated SnO₂/TiO₂ composite electrode has been applied to the dye-sensitized solar cell. In such an electrode, two kinds of energy barriers (SnO₂/TiO₂ and TiO₂/Al₂O₃) were designed to suppress the recombination processes of the photo-generated electrons and holes. After the SnO₂ was modified by colloid TiO₂, the photoelectric conversion efficiency of the SnO₂/TiO₂ composite cell increased to 2.08% by a factor of 2.8 comparing with that of the SnO₂ cell. The Al₂O₃ layer on the SnO₂/TiO₂ composite electrode further suppressed the generation of the dark current, resulting in 37% improvement in device performance comparing with the SnO₂/TiO₂ cell.     

Study on the formation process of Al2O3-TiO2 composite powders

Fine particles of anatase were suspended in solutions of ammonium alum with Al₂O₃/TiO₂ molar ratios from 0.1:1 to 7:1. By spray drying the suspensions and calcining the spray-dried powders, Al₂O₃-TiO₂ composite particles were obtained. The results show that after the spray drying, coatings of ammomium alum are formed on the surface of the anatase particles, leading to composite precursor powders (CCPs) with larger particle sizes. Upon calcining the CCPs, ammomium alum pyrolyzes to amorphous Al₂O₃ and anatase transforms into rutile. Both are mainly responsible for the observed particle size reductions as well as the densification of each composite particle. The in-situ formed α-Al₂O₃ and rutile may have higher reactivities, forming aluminum titanate at 1150 °C, about 130 °C lower than the theoretical temperature for the formation of Al₂TiO₅ by solid reaction. The reaction between α-Al₂O₃ and rutile starts from the interface between the anatase and the alum coating and mainly takes place in the single particles formed by spray drying. The molar ratio of Al₂O₃ to TiO₂ influences the final crystalline phases in the composite powders, but not stoichiometrically.     

Dynamic corrosion of Al2O3-ZrO2-SiO2 and Cr2O3-containing refractories by molten frits. Part I: Macroscopic analysis

Manufacturing of enamels and frits has undergone dramatic changes since the 1980s. This has required significant efforts in research and development. Typical compositions of frits for ceramic tiles are silica-based with fluxing agents; some of the components are highly corrosive. Improvements in the production of frits would imply the selection of the most adequate refractories as a function of the chemical composition of the considered frit and the fabrication procedure.The refractories currently used in frit furnaces are Al₂O₃-ZrO₂-SiO₂ (AZS) fused cast materials and Cr₂O₃-based materials. In this work, results on dynamic corrosion studies of AZS and Cr₂O₃-based materials by two ZnO-containing frits are described. Experiments have been performed using the “Merry Go Round” test at ≅1500 °C. Macroscopic results are analysed in terms of the remaining volume after the tests, as usually done in the glass industry. The significance and limits of such an approach are discussed.     

Dynamic corrosion of Al2O3-ZrO2-SiO2 and Cr2O3-containing refractories by molten frits. Part II: Microstructural study

In this work results on dynamic corrosion studies of fused cast Al₂O₃-SiO₂-ZrO₂ and isostatically pressed and sintered Cr₂O₃-based refractories by two crystalline (transparent) frits are described. Experiments have been performed using the “Merry Go Round” test at ≅1500 °C.Microstructural and mineralogical analyses of selected areas from the corroded regions of the studied refractories were performed by reflected light optical microscopy and scanning electron microscopy with analysis by X-ray dispersive energy.Significant differences between the corrosion mechanisms acting in the two types of materials were found. In the fused cast Al₂O₃-SiO₂-ZrO₂ specimens corrosion took place by the dissolution of alumina and zirconia in the frit and in the glass formed by the reaction between the frit and the refractory. In the Cr₂O₃-based materials the corrosion process was controlled by the capillar penetration of the molten frit through the open pores. The reaction between the ZnO from the frits and Cr₂O₃ led to the formation of spinel (ZnCr₂O₄), a high-melting point bonding phase that retarded the frit penetration. Results are discussed using the relevant phase equilibrium diagrams.     

Formation of GdAlO3–Al2O3 composite having fine pseudo-eutectic microstructure

GdAlO₃ and Al₂O₃ powders were mixed and pulverized using ball mills. The prepared powder was sintered by SPS at 1450 °C without holding time. SEM observation of the sintered specimen showed a eutectic-like microstructure. This is called ‘pseudo-eutectic’ in this research. The microstructure formed from a powder pulverized by a tumbling ball mill for one week was much finer than that by a planetary ball mill for 5 and 10 h. The fine homogeneous eutectic-like (pseudo-eutectic) microstructures could be formed at both eutectic and off-eutectic compositions. In case of crystallization from a melt of eutectic components, homogeneous eutectic microstructures can be formed only at restricted compositions very close to the eutectic one. Coarse primary crystals generally exist in the eutectic microstructure at off-eutectic compositions. The pseudo-eutectic microstructures can be formed at any compositions because a mixing ratio of the starting powders can be varied.     

Steady State Isotopic Transient Kinetic Analysis of Flameless Methane Combustion over Pd/Al2O3 and Pt/Al2O3 Catalysts

The SSITKA measurements were performed in the steady state of complete methane oxidation on the Pd/Al₂O₃ and Pt/Al₂O₃ catalysts. It was found that the number of intermediates and their average life-time on the catalyst surface changes with the increase of reaction temperature. On the Pd/Al₂O₃ catalyst there is larger number of active centres than on Pt/Al₂O₃ catalyst which permits the course of methane oxidation at lower temperatures.     

Processing and physical properties of Al2O3/aluminum alloy composites

Porous aluminum oxide (Al₂O₃) preforms were formed by sintering in air at 1200 °C for 2 h. A356, 6061, and 1050 aluminum alloys were infiltrated into the preforms by squeeze casting in order to fabricate Al₂O₃/A356, Al₂O₃/6061, and Al₂O₃/1050 composites, respectively, with different volumes of aluminum alloy content. The content of aluminum alloy in the composites was 10–40% by volume. The resistivity of Al₂O₃/A356, Al₂O₃/6061, and Al₂O₃/1050 composites decreased dramatically from 6.41 × 10¹² to 9.77 × 10⁻⁴, 7.28 × 10⁻⁴, and 6.24 × 10⁻⁴ Ω m, respectively, the four-points bending strength increased from 397 to 443, 435.1, 407.2 MPa, respectively, and the deviations were smaller than 2%. From SEM microstructural analysis and TEM bright field images, the pore volume fraction and the relative density of the composites were the most important factors that affected the physical and mechanical properties. The ceramic phase and alloy phase in Al₂O₃/aluminum alloy composites were found to be homogenized and uniformly distributed using electrical and mechanical properties analysis, microstructure analysis, and image analysis.     

Sintering of Al2O3-SiC composite from sol-gel method with MgO, TiO2 and Y2O3 addition

Al₂O₃-SiC composite ceramics were prepared by pressureless sintering with and without the addition of MgO, TiO₂ and Y₂O₃ as sintering aids. The effects of these compositional variables on final density and hardness were investigated. In the present article at first α-Al₂O₃ and β-SiC nano powders have been synthesized by sol-gel method separately by using AlCl₃, TEOS and saccharose as precursors. Pressureless sintering was carried out in nitrogen atmosphere at 1600 °C and 1630 °C. The addition of 5 vol.% SiC to Al₂O₃ hindered densification. In contrast, the addition of nano MgO and nano TiO₂ to Al₂O₃-5 vol.% SiC composites improved densification but Y₂O₃ did not have positive effect on sintering. Maximum density (97%) was achieved at 1630 °C. Vickers hardness was 17.7 GPa after sintering at 1630 °C. SEM revealed that the SiC particles were well distributed throughout the composite microstructures. The precursors and the resultant powders were characterized by XRD, STA and SEM.     

Selective synthesis of mixed alcohols from syngas over catalyst Fe2O3/Al2O3 in slurry reactor

The Fe₂O₃/Al₂O₃ catalyst was studied to selectively synthesize mixed alcohols from syngas in a continuously stirred slurry reactor with the oxygenated solvent Polyethylene Glycol-400 (PEG-400). The selectivity of mixed alcohols in the products reached as high as 95 wt.% and the C₂₊ alcohols (mainly ethanol) was more than 40 wt.% in the total alcohol products at the reaction conditions of 250 °C, 3.0 MPa, H₂/CO = 2 and space velocity = 360 ml/g_cat h. The hydrogen temperature programmed reduction (H₂-TPR) and X-ray photoelectron spectroscopy (XPS) measurements of the catalyst confirmed that the FeO phase was responsible for the high selectivity to mixed alcohols in the process. And the oxygenated solvent PEG-400 was also necessary for the selective synthesis of mixed alcohols in the reaction system.     

Corrosion mechanisms of Al2O3/MgAl2O4 by V2O5, NiO, Fe2O3 and vanadium slag

The effects of V₂O₅, NiO, Fe₂O₃ and vanadium slag on the corrosion of Al₂O₃ and MgAl₂O₄ have been investigated. The specimens of Al₂O₃ and MgAl₂O₄ with the respective oxides above mentioned were heated at 10 °C/min from room temperature up to three different temperatures: 1400, 1450 and 1500 °C. The corrosion mechanisms of each system were followed by XRD and SEM analyses. The results obtained showed that Al₂O₃ was less affected by the studied oxides than MgAl₂O₄. Alumina was only attacked by NiO forming NiAl₂O₄ spinel, while the MgAl₂O₄ spinel was attacked by V₂O₅ forming MgV₂O₆. It was also observed that Fe₂O₃ and Mg, Ni, V and Fe present in the vanadium slag diffused into Al₂O₃. On the other hand, the Fe₂O₃ and Ca, S, Si, Na, Mg, V and Fe diffused into the MgAl₂O₄ structure. Finally, the results obtained were compared with those predicted by the FactSage software.     

Synthesis and electrochemical characteristics of Al2O3-coated LiNi1/3Co1/3Mn1/3O2 cathode materials for lithium ion batteries

LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials have been coated with Al₂O₃ nano-particles using sol-gel processing to improve its electrochemical properties. The X-ray diffraction (XRD) pattern of the as-prepared Al₂O₃ nano-particles was indexed to the cubic structure of the γ-Al₂O₃ phase and had an average size of ∼4 nm. The XRD showed that the structure of LiNi_1/3Co_1/3Mn_1/3O₂ was not affected by the Al₂O₃ coating. However, the Al₂O₃ coatings on LiNi_1/3Co_1/3Mn_1/3O₂ improved the cyclic life performance and rate capability without decreasing its initial discharge capacity. These electrochemical properties were also compared with those of LiAlO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ cathode material. The electrochemical impedance spectroscopy (EIS) was studied to understand the enhanced electrochemical properties of the Al₂O₃-coated LiNi_1/3Co_1/3Mn_1/3O₂ compared to uncoated LiNi_1/3Co_1/3Mn_1/3O₂.     

Synergetic effect of combined use of Cu–ZnO–Al2O3 and Pt–Al2O3 for the steam reforming of methanol

Commercial Cu–ZnO–Al₂O₃ catalysts are used widely for steam reforming of methanol. However, the reforming reactions should be modified to avoid fuel cell catalyst poisoning originated from carbon monoxide. The modification was implemented by mixing the Cu–ZnO–Al₂O₃ catalyst with Pt–Al₂O₃ catalyst. The Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalyst mixture created a synergetic effect because the methanol decomposition and the water–gas shift reactions occurred simultaneously over nearby Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalysts in the mixture. A methanol conversion of 96.4% was obtained and carbon monoxide was not detected from the reforming reaction when the Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalyst mixture was used.     

Mechanical properties of Al2O3-Cr2O3/Cr3C2 nanocomposite fabricated by spark plasma sintering

The fine grains of Al₂O₃-Cr₂O₃/Cr-carbide nanocomposites were prepared by employing recently developed spark plasma sintering (SPS) technique. The initial materials were fabricated by a metal organic chemical vapor deposition (MOCVD) process, in which Cr(CO)₆ was used as a precursor and Al₂O₃ powders as matrix in a spouted chamber. The basic mechanical properties like hardness, fracture strength and toughness, and the nanoindentation characterization of nanocomposites such as Elastics modulus (E), elastic work (W_e) and plastic work (W_p) were analyzed. The microstructure of dislocation, transgranular and step-wise fracture surface were observed in the nanocomposites. The nanocomposites show fracture toughness of (4.8 MPa m^1/2) and facture strength (780 MPa), which is higher than monolithic alumina. The strengthening mechanism from the secondary phase and solid solution are also discussed in the present work. Nanoindentation characterization further illustrates the strengthening of nanocomposites.