Relaxation of stress in polypropylene and ethylene–propylene–diene elastomer blend vulcanizates at moderate and high extensions

Measurements were made of the relaxation of the stress of stretched polypropylene (PP) and ethylene–propylene–diene elastomer blend vulcanizates at various strain levels. It was found that PP-blended vulcanizates showed greater relaxation than that of the gum vulcanizate at all extensions. There was a continual increase in the relaxation rate with the 10% PP-blended vulcanizate but an initial sharp decrease and then a flattening tendency with the above 10% PP-blended vulcanizate at an increasing stain level. An interesting observation of the study was that the rate of stress relaxation decreased linearly in two steps in the case of blend vulcanizates above 10% PP at 100% and above strain levels. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 2155–2162, 1998     

Influence of the compounding route on the properties of polypropylene/nano‐CaCO3/ethylene–propylene–diene terpolymer tercomponent composites

The influence of the compounding route of polypropylene (PP)/ethylene–propylene–diene terpolymer (EPDM)/nano‐CaCO₃ composites on their properties, including their mechanical properties, the dispersion degree of nano‐CaCO₃, and the morphology of EPDM, was studied. The results showed that the toughness of the composites and the morphology of the EPDM particles were markedly influenced by the compounding route, whereas the dispersion degree of nano‐CaCO₃ in the matrix was little influenced by the compounding route. The impact strength of composites prepared by one route was about 60 kJ/m² with 20 wt % nano‐CaCO₃. The results indicated that a sandbag of nano‐CaCO₃ embedded in EPDM could effectively improve the toughness of the composites. A sandbag composed of EPDM and nano‐CaCO₃ eliminated the deterioration effect of the nano‐CaCO₃ agglomerate on the toughness of the composites, whereas the nano‐CaCO₃ agglomerate separately dispersed in PP decreased the toughness of the tercomponent composite © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Miscibility of blends of ethylene‐propylene‐diene terpolymer and polypropylene

The miscibility of polymers is not only an important basis for selecting a proper blending method, but it is also one of the key factors in determining the morphology and properties of the blends. The miscibility between ethylene‐propylene‐diene terpolymer (EPDM) and polypropylene (PP) was explored by means of dynamic mechanical thermal analysis, transmission electron microscopy (TEM), and differential scanning calorimetry (DSC). The results showed that a decrease in the PP content and an increase of the crosslinking density of EPDM in the EPDM/PP blends caused the glass‐transition temperature peaks of EPDM to shift from a lower temperature to higher one, yet there was almost no variance in the glass‐transition temperature peaks of PP and the degree of crystallinity of PP decreased. It was observed that the blends prepared with different mixing equipment, such as a single‐screw extruder and an open mill, had different mechanical properties and blends prepared with the former had better mechanical properties than those prepared with the latter. The TEM micrographs revealed that the blends were composed of two phases: a bright, light PP phase and a dark EPDM phase. As the crosslinking degree of EPDM increased, the interface between the phases of EPDM and PP was less defined and the EPDM gradually dispersed in the PP phase became a continuous phase. The results indicated that EPDM and PP were both partially miscible. The mechanical properties of the blends had a lot to do with the blend morphology and the miscibility between the blend components. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 315–322, 2002     

Dynamic mechanical properties of polypropylene‐g‐maleic anhydride and ethylene–propylene–diene terpolymer blends: Effect of blend preparation methods

In this work, we attempted two different ways of processing to improve interfacial adhesion of polypropylene (PP) and ethylene–propylene–diene terpolymer (EPDM) by introducing maleic anhydride (MAH); In one way, the in situ grafting and dynamic vulcanization (ISGV) were performed simultaneously from PP and EPDM with MAH in the presence of dicumyl peroxide (DCP) in an intensive mixer. In another way, PP was first grafted with MAH and then the PP‐g‐MAH was blended with EPDM in the intensive mixer in the presence of DCP by the dynamic vulcanization (DV). It was found that the glass transition temperatures (T_gs) of both PP and EPDM phases were shifted to higher temperature as the EPDM content increased for the blends prepared by both IGSV and DV methods, mainly due to the crosslinking of EPDM. The higher T_gs and larger storage moduli were observed for the blends prepared by the ISGV method than those prepared by the DV method, while the morphology showed that the size reduction of dispersed particles in latter blends was larger than that of the former blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2777–2784, 2000     

Properties of dynamically vulcanized ethylene–propylene–diene copolymer/polypropylene blends

In this study, vulcanized thermoplastic elastomers were produced through the formation of crosslinks with peroxide for different ratios of ethylene–propylene–diene copolymer to polypropylene. Mixing was performed with a twin‐screw extruder. Afterward, the yield, tensile strength, elastic modulus, elongation, Izod impact strength, hardness, melt flow index, Vicat softening point, heat deflection temperature, and density of the crosslinks were determined. The thermal transition temperatures and microstructure were determined with differential scanning calorimetry and scanning electron microscopy, respectively. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 3895–3902, 2007     

Ethylene–propylene‐diene terpolymer/halloysite nanocomposites: Thermal,mechanical properties,and foam processing

Ethylene–propylene‐diene terpolymer (EPDM)/halloysite nanotube (HNT) nanocomposites were prepared by melt mixing in an internal mixer using a commercially available maleated semicrystalline EPDM and HNT. Transmission electron microscopy analysis of the EPDM/HNT composites revealed that the HNTs are uniformly dispersed at a nanometer scale in the matrix. Differential scanning calorimeter studies indicated that the HNT caused an increase in the nonisothermal crystallization temperature of the EPDM. Tensile and dynamic mechanical analysis exhibited that a small amount of the HNTs effectively enhanced the stiffness of the EPDM without adversely affecting its elongation‐at‐break. The EPDM/HNT nanocomposites were used to produce foams by using a batch process in an autoclave, with supercritical carbon dioxide as a foaming agent. The nanocomposite foams showed a smaller cell size and higher cell density as compared to the neat EPDM foam, and the nanocomposite with 10 phr HNT produced a microcellular foam with average cell size as small as 7.8 μm and cell density as high as 1.5 × 10¹⁰ cell/cm³. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40307.     

Abrasion resistance of thermoplastic polyurethane materials blended with ethylene–propylene–diene monomer rubber

The effect of ethylene–propylene–diene monomer rubber (EPDM) as an additive on the abrasion resistance of a thermoplastic polyurethane (TPU) resin was investigated. The mechanical properties and microstructure of the resultant TPU/EPDM composites were evaluated, and the surface morphology of the composites after abrasion testing was examined. The results showed that the addition of EPDM greatly improved both the mechanical properties and abrasion resistance of the TPU resin. A TPU/EPDM composite with 8 wt % EPDM demonstrated the highest tensile strength, the largest elongation at break, and the best overall performance. The abrasion of this composite was 27 mg, whereas that of the pure resin was 73 mg. With the further addition of EPDM, the abrasion resistance of the resultant composites decreased, whereas the viscosity increased. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Properties of copolymer-type polyacetal/ethylene–propylene–diene terpolymer blends

Two kinds of polymer blends, polyacetals (POMs) and ethylene–propylene–diene terpolymer (EPDM), have been prepared by mechanical blending. The rubbery EPDM was added to the rigid POM matrix to increase toughness. The mechanical, physical, thermal, dynamic mechanical, and morphological properties of these samples have been measured. The notched Izod impact strength and the elongation of the blends reaches a maximum at 7.5 wt % EPDM content. Scanning electron micrographs (SEM) showed that the domain sizes of EPDM vary from 0.25 to 1.0 μm and were independent of the composition. The POM/EPDM blends were determined to be immiscible by SEM, but showed single T_g behavior as determined by differential scanning calorimetry (DSC) and dynamic mechanical analyses up to 7.5 wt % EPDM. Because of that, the T_g's of POM and EPDM were very similar in value. © 1993 John Wiley & Sons, Inc.     

Photocrosslinking of an ethylene–propylene–diene terpolymer and the characterization of its structure and mechanical properties

An ethylene–propylene–diene terpolymer (EPDM) was photocrosslinked under UV irradiation with benzil dimethyl ketal (BDK) as a photoinitiator and trimethylolpropane triacrylate (TMPTA) as a crosslinker. The efficiency of the photoinitiated crosslinking system EPDM–BDK–TMPTA, various factors affecting the crosslinking process (the photoinitiator and crosslinker and their concentrations, the irradiation time, the temperature, the atmosphere and UV‐light intensity, and the depth of the UV‐light penetration), and the mechanical properties of photocrosslinked EPDM were examined extensively through the determination of the gel contents, infrared spectra, and mechanical measurements. EPDM samples 3 mm thick were easily crosslinked with a gel content of about 90% after 30 s of UV irradiation under optimum conditions. The photoinitiating system of a suitable initiator combined with a multifunctional crosslinker such as BDK–TMPTA enhanced the efficiency of the photocrosslinking reaction, especially by increasing the initial rate of crosslinking. The gel content of photocrosslinked EPDM, which was determined by the content of diene in EPDM, the depth of the UV‐light penetration, and the light intensity, played a key role in increasing the mechanical properties of the photocrosslinked samples in this work. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1837–1845, 2004     

Effect of dynamic crosslinking on impact strength and other mechanical properties of polypropylene/ethylene‐propylene‐diene rubber blends

The deformation and fracture behavior of several dynamic vulcanizate blends of isotactic polypropylene with ethylene‐propylene‐diene rubber (EPDM) was examined and compared with those of uncrosslinked blends of PP/EPDM. These blends were prepared by melt mixing in an internal mixer at 190°C in a composition range of 10–40 wt % EPDM rubber. The variation in yield stress, the strength of fibrils of the craze, and the number density of the EPDM rubber domains (morphology fixation) that are dominant factors for enhancing interfacial adhesion and toughness in dynamic vulcanizate blends were evaluated. The ductility and toughness of these materials were explained in light of the composition between crack formation and the degree of plastic deformation through crazing and shear yielding. The physicomechanical properties including the hardness, yield stress, Young's modulus, percentage elongation, impact strength, flexural strength, and flexural modulus of dynamic vulcanized blends were found to be consistent and displayed higher values compared with uncrosslinked blends. The nucleation effect of the crosslinked particles and the decrease of crystallinity of the EPDM rubber were also considered to contribute to the improvement in the impact strength. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2089–2103, 2000     

Degradation kinetics of vulcanized ethylene–propylene–diene terpolymer residues

In this study, ethylene–propylene–diene terpolymer residues (EPDM‐r) from the automotive industry were analyzed by thermogravimetric analysis (TGA) for determination of the activation energy (E_a) of decomposition by the Flynn‐Wall‐Ozawa (FWO) method. The degradation mechanism was determined by the method of Criado et al. Analysis of the nonvulcanized EPDM gum (EPDM‐g) and paraffinic oil used in the composition of the compound was also carried out. The E_a values for the decomposition of the EPDM‐g and paraffinic oil remained constant with the conversion, but for the EPDM‐r decomposition, they changed due to the initial oil elimination followed by decomposition of the EPDM fraction. It was observed that removal of the paraffinic oil occurred less easily in the tridimensional vulcanized network, and there were differences in the elimination mechanism. The EPDM degradation mechanism was also affected by vulcanization and the fillers present in the compound. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Viscosities of ethylene–propylene–diene terpolymer blends in oil

Viscosities were obtained on oil solutions of two ethylene–propylene–diene terpolymers (EPDMs) and their blends. For the amorphous terpolymer with 59 mol% ethylene, intrinsic viscosities were constant between–10 and 40°C. The viscosities decreased rapidly at low temperature for blends of this material with as little as 20 wt % of a slightly crystalline EPDM with 79 mol% ethylene. Dynamic viscosity measurements on 1.0% solutions of blends likewise gave considerably smaller values at low temperature than measurements on an amorphous EPDM of similar molecular weight. The data are in agreement with the view that longer ethylene sequences that crystallize in the bulk polymer can organize in oil into ordered domains that interfere less with flow than the disordered amorphous polymer regions. © 1993 John Wiley & Sons, Inc.     

Mechanical and morphological properties of white rice husk ash filled polypropylene/ethylene‐propylene‐diene terpolymer thermoplastic elastomer composites

The performance of white rice husk ash (WRHA) as filler for polypropylene (PP)/ethylene‐propylene‐diene terpolymer (EPDM) thermoplastic elastomer (TPE) composites was investigated. The composites with different filler loadings were prepared in a Brabender plasticorder internal mixer. Both unvulcanized and dynamically vulcanized composites were prepared. Mixing and vulcanization processes of the composites were monitored through the typical Brabender torque‐time curves. The mechanical properties and morphology of the composites were also studied. The Brabender torque curves revealed that the dynamic vulcanization process employed was successful and incorporation of filler has no adverse effect on the processibility of the composites. Incorporation of WRHA improves the tensile modulus and flexural modulus and lowers tensile strength, elongation at break, tear strength, and toughness of both types of composites. Dynamic vulcanization significantly enhances the mechanical and TPE properties of the composites. Dynamic mechanical analysis (DMA) study revealed the existence of two phases in both types of composites. It further shows that neither dynamic vulcanization nor filler agglomeration has played a prominent role in the compatibility of the composites. Thermogravimetric investigation shows that dynamic vulcanization or WRHA loading has not adversely affected the thermal stability of the composites. The scanning electron micrographs provide evidence for the tendency to form filler agglomerates with increasing filler loading, better filler dispersion of dynamically vulcanized composites over unvulcanized composites, and effective vulcanization of elastomer phase of the composites in the presence of filler. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 438–453, 2002     

Dynamic mechanical analysis of ethylene–propylene–diene monomer rubber and styrene–butadiene rubber blends

The effects of blend ratio, crosslinking systems, and fillers on the viscoelastic response of ethylene–propylene–diene monomer (EPDM)/styrene–butadiene rubber (SBR) blends were studied as functions of frequency, temperature, and cure systems. The storage modulus decreased with increasing SBR content. The loss modulus and loss tangent results showed that the EPDM/SBR blend vulcanizate containing 80 wt % EPDM had the highest compatibility. Among the different cure systems studied, the dicumyl peroxide cured blends exhibited the highest storage modulus. The reinforcing fillers were found to reduce the loss tangent peak height. The blend containing 40 wt % EPDM showed partial miscibility. The dispersed EPDM phase suppressed the glass‐transition temperature of the matrix phase. The dynamic mechanical response of rubbery region was dominated by SBR in the EPDM–SBR blend. The morphology of the blend was studied by means of scanning electron microscopy. The blend containing 80 wt % EPDM had small domains of SBR particles dispersed uniformly throughout the EPDM matrix, which helped to toughen the matrix and prevent crack propagation; this led to enhanced blend compatibility. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Cure and scorch in the processing of ethylene‐propylene‐diene terpolymer (EPDM)

The objective of this work is to ascertain the characteristics of desirable (cure) and especially undesirable (scorch) crosslinking when carbon black filled ethylene propylene diene terpolymer (EPDM) is processed using different peroxide initiators. The mixing temperature and the nature of the peroxide initiator are crucial parameters affecting scorch (undesirably premature crosslinking) in this rubber. Processability and properties of EPDM prepared using various mixer set temperatures have been investigated. Dicumyl peroxide (Luperox DC), di(t‐butylperoxy) diisopropylbenzene (Luperox F), and 2,5‐dimethyl‐2,5‐di(t‐butylperoxy) hexane (Luperox 101) were used as crosslinking initiators. Higher mixing temperatures give shorter scorch times, greater scorch magnitudes, greater heterogeneities in crosslink spatial distribution and poorer tensile properties. However, extreme localization of the unwanted crosslinking at the rubber‐filler interface does have a beneficial effect. Luperox DC offers poorer processability and poorer resulting properties than do Luperox F and Luperox 101, due to its shorter half‐life and greater solubility in the rubber phase. This is the first time that the spatial heterogeneity of crosslinking and scorch has been related to the basic thermodynamics of 3‐component 2‐phase systems. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44523.     

Acrylonitrile–styrene copolymer grafted onto ethylene–propylene–diene terpolymer

The two-phase structure of the acrylonitrile–styrene copolymer grafted onto ethylene–propylene–diene terpolymer (EPDM) was investigated using an electron microscope. It was found that the microstructure depends on the solvent system for graft copolymerization, separation of the graft copolymer, and the processing procedure. The graft EPDM phase forms the discontinuous phase in chlorobenzene and in the toluene–ethyl acetate mixed solvent, whereas it is the continuous phase in the hexane–ethyl acetate mixed solvent. The phase inversion of the rubber phase in the case of the latter is carried out partially in the separation procedure and completely in the processing procedure.     

Effect of dynamic cross‐linking on melt rheological properties of polypropylene/ethylene‐propylene‐diene rubber blends

Study of melts rheological properties of unvulcanized and dynamically vulcanized polypropylene (PP)/ethylene‐propylene‐diene rubber (EPDM) blends, at blending ratios 10–40 wt %, EPDM, are reported. Blends were prepared by melt mixing in an internal mixer at 190°C and rheological parameters have been evaluated at 220°C by single screw capillary rheometer. Vulcanization was performed with dimethylol phenolic resin. The effects of (i) blend composition; (ii) shear rate or shear stress on melt viscosity; (iii) shear sensitivity and flow characteristics at processing shear; (iv) melt elasticity of the extrudate; and (v) dynamic cross‐linking effect on the processing characteristics of the blends were studied. The melt viscosity increases with increasing EPDM concentration and decreased with increasing intensity of the shear mixing for all compositions. In comparison to the unvulcanized blends, dynamically vulcanized blends display highly pseudoplastic behavior provides unique processing characteristics that enable to perform well in both injection molding and extusion. The high viscosity at low shear rate provides the integrity of the extrudate during extrusion, and the low viscosity at high shear rate enables low injection pressure and less injection time. The low die‐swell characteristics of vulcanizate blends also give high precision for dimensional control during extrusion. The property differences for vulcanizate blends have also been explained in the light of differences in the morphology developed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1488–1505, 2000     

Effect of melt flow on morphology and linear thermal expansion of injection‐molded ethylene–propylene–diene terpolymer/isotactic polypropylene blends

An ethylene–propylene–diene terpolymer/isotactic polypropylene blend with a structure of co‐continuous microlayers was fabricated by injection molding and was then investigated. The blend exhibited an extremely low coefficient of linear thermal expansion (CLTE) in the directions of the length and the width. As the thickness of the oriented portion increased, the CLTE was further reduced. The morphology of the co‐continuous microlayers and the thermal expansion behavior varied with the sampling positions on the injection‐molded sheets. To study the relationship between the morphology and the melt flow, the melt flow behavior during injection molding was simulated using Moldflow. Orientation of the microlayers was determined using shear flow. When the shear rate increased, the orientation state increased and the CLTE decreased. © 2015 Society of Chemical Industry     

Structure and properties of peroxide dynamically vulcanized polypropylene/ethylene–propylene–diene/zinc dimethacrylate composites

Peroxide dynamically vulcanized thermoplastic olefin (TPO) based on polypropylene (PP)/ethylene–propylene–diene (EPDM) loaded with zinc dimethacrylate (ZDMA) was prepared. The addition of ZDMA improved the complex viscosity of the resulting materials in the melt state significantly, as determined from oscillatory rheology analyses. Dynamic mechanical analysis (DMA) and transmission electron microscopy (TEM) examinations were performed to evaluate the structure of the PP/EPDM/ZDMA composite. Atomic force microscope (AFM) and scanning electron microscopy (SEM) were used to study the morphology. The degree of crystallinity was evaluated using X‐ray diffraction method (XRD). The results revealed that incorporation of ZDMA resulted in a size reduction of the rubber droplets and improved the compatibility between rubber and PP phases. The nanoparticles of the polymerized ZDMA (PZDMA) served as an effective nucleating agent for the crystallization of PP. The rheological properties and mechanical properties were improved by ZDMA. Particularly, the izod impact strength of the PP/EPDM/ZDMA (80/20/6, w/w) composite is nearly 2 times higher than the PP/EPDM (80/20, w/w) and 12 times higher than the PP; besides, the elongation at break of the PP/EPDM/ZDMA (80/20/6, w/w) is 3 times higher than that of the PP/EPDM (80/20, w/w) and 6 times higher than the PP. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Synthesis of brominated acenaphthylenes and their flame-retardant effects on ethylene–propylene–diene terpolymer

Bromoacenaphthylenes and their condensates as flame-retardant reagents were synthesized by bromination of acenaphthylene using ZnCl₂? CF₃COOH or FeCl₃ as catalysts and subsequent dehydrobromination. The chief components were identified as bromoacenaphthylene monomers when ZnCl₂? CF₃COOH were used, and as their condensates (mostly trimers) in the case of FeCl₃. Their performance as flame-retardant reagents for ethylene–propylene–diene terpolymer (EPDM) was evaluated by measuring the oxygen index of finished compounds, and flammability by a vertical flammability test based on UL-94-VO. Both the monomers and the condensates demonstrated high flame-retardant effectiveness. The high efficiency was attributed to their excellent dispersity in the base polymer and their characteristic thermal decomposition behavior. In TGA, they decomposed in a very wide range of temprature (ca.200–560°C), which covers the decomposition range of EPDM. This was attributed to the existence of bromines of different thermal stabilities in one molecule.